Add CMU/RMU/DMA/MMC/I2C support for Actions Semi
Subsystems (5)
v3 cover Add CMU/RMU/DMA/MMC/I2C support for Actions Semi
Hi,
This patchset brings a series of improvements for the Actions Semi S500 SoCs family, by adding support for Clock & Reset Management Units, DMA, MMC, I2C & SIRQ controllers.
Please note the patches consist mostly of DTS and bindings/compatibles changes, since all the work they depend on has been already merged, i.e. clock fixes/additions, pinctrl driver, sirq driver.
For the moment, I have only enabled the features I could test on RoseapplePi SBC.
Thanks,
Cristi
Changes in v3:
- Squashed 'arm: dts: owl-s500-roseapplepi: Use UART clock from CMU' with 'arm: dts: owl-s500: Set CMU clocks for UARTs', according to Mani's review
- Rebased series on v5.11-rc1 and dropped the already merged patches:
* dt-bindings: mmc: owl: Add compatible string for Actions Semi S500 SoC
* dt-bindings: i2c: owl: Convert Actions Semi Owl binding to a schema
* MAINTAINERS: Update entry for Actions Semi Owl I2C binding
* i2c: owl: Add compatible for the Actions Semi S500 I2C controller
Changes in v2:
- Added new bindings/compatibles for S500 DMA, MMC & I2C controllers
- Added support for the SIRQ controller
- Added new entries in MAINTAINERS
- Updated naming of some patches in v1
Cristian Ciocaltea (13):
arm: dts: owl-s500: Add Clock Management Unit
arm: dts: owl-s500: Set CMU clocks for UARTs
arm: dts: owl-s500: Add Reset controller
dt-bindings: dma: owl: Add compatible string for Actions Semi S500 SoC
dmaengine: owl: Add compatible for the Actions Semi S500 DMA
controller
arm: dts: owl-s500: Add DMA controller
arm: dts: owl-s500: Add pinctrl & GPIO support
arm: dts: owl-s500: Add MMC support
arm: dts: owl-s500: Add I2C support
arm: dts: owl-s500: Add SIRQ controller
arm: dts: owl-s500-roseapplepi: Add uSD support
arm: dts: owl-s500-roseapplepi: Add I2C pinctrl configuration
MAINTAINERS: Add linux-actions ML for Actions Semi Arch
.../devicetree/bindings/dma/owl-dma.yaml | 7 +- MAINTAINERS | 1 + arch/arm/boot/dts/owl-s500-cubieboard6.dts | 7 - .../arm/boot/dts/owl-s500-guitar-bb-rev-b.dts | 7 - .../arm/boot/dts/owl-s500-labrador-base-m.dts | 7 - arch/arm/boot/dts/owl-s500-roseapplepi.dts | 97 +++++++++++- arch/arm/boot/dts/owl-s500-sparky.dts | 7 - arch/arm/boot/dts/owl-s500.dtsi | 140 ++++++++++++++++++ drivers/dma/owl-dma.c | 3 +- 9 files changed, 239 insertions(+), 37 deletions(-)
Signature · 1 line
2.30.0
PATCH v3 1/13 arm: dts: owl-s500: Add Clock Management Unit
Add Clock Management Unit for Actions Semi S500 SoC.
---
Changes in v3:
- Added Reviewed-by from Mani
arch/arm/boot/dts/owl-s500.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
arch/arm/boot/dts/owl-s500.dtsi +14 -0
@@ -5,6 +5,7 @@ * Copyright (c) 2016-2017 Andreas Färber */ +#include <dt-bindings/clock/actions,s500-cmu.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/power/owl-s500-powergate.h>
@@ -70,6 +71,12 @@ hosc: hosc { #clock-cells = <0>; }; + losc: losc { + compatible = "fixed-clock"; + clock-frequency = <32768>; + #clock-cells = <0>; + }; + soc { compatible = "simple-bus"; #address-cells = <1>;
@@ -169,6 +176,13 @@ uart6: serial@b012c000 { status = "disabled"; }; + cmu: clock-controller@b0160000 { + compatible = "actions,s500-cmu"; + reg = <0xb0160000 0x8000>; + clocks = <&hosc>, <&losc>; + #clock-cells = <1>; + }; + timer: timer@b0168000 { compatible = "actions,s500-timer"; reg = <0xb0168000 0x8000>;
Signature · 1 line
2.30.0
PATCH v3 2/13 arm: dts: owl-s500: Set CMU clocks for UARTs
In reply to Cristian CiocalteaSet Clock Management Unit clocks for the UART nodes of Actions Semi S500 SoCs and remove the dummy "uart2_clk" and "uart3_clk" fixed clocks.
---
Changes in v3:
- Added Reviewed-by from Mani
- Removed the dummy 'uart2_clk' and 'uart3_clk' nodes from all owl-s500 DTS, per Mani's review
arch/arm/boot/dts/owl-s500-cubieboard6.dts | 7 ------- arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts | 7 ------- arch/arm/boot/dts/owl-s500-labrador-base-m.dts | 7 ------- arch/arm/boot/dts/owl-s500-roseapplepi.dts | 7 ------- arch/arm/boot/dts/owl-s500-sparky.dts | 7 ------- arch/arm/boot/dts/owl-s500.dtsi | 7 +++++++ 6 files changed, 7 insertions(+), 35 deletions(-)
arch/arm/boot/dts/owl-s500-cubieboard6.dts +0 -7
@@ -25,12 +25,6 @@ memory@0 { device_type = "memory"; reg = <0x0 0x80000000>; }; - - uart3_clk: uart3-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &timer {
@@ -39,5 +33,4 @@ &timer { &uart3 { status = "okay"; - clocks = <&uart3_clk>; };
arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts +0 -7
@@ -18,15 +18,8 @@ aliases { chosen { stdout-path = "serial3:115200n8"; }; - - uart3_clk: uart3-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &uart3 { status = "okay"; - clocks = <&uart3_clk>; };
arch/arm/boot/dts/owl-s500-labrador-base-m.dts +0 -7
@@ -21,15 +21,8 @@ aliases { chosen { stdout-path = "serial3:115200n8"; }; - - uart3_clk: uart3-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &uart3 { status = "okay"; - clocks = <&uart3_clk>; };
arch/arm/boot/dts/owl-s500-roseapplepi.dts +0 -7
@@ -25,12 +25,6 @@ memory@0 { device_type = "memory"; reg = <0x0 0x80000000>; /* 2GB */ }; - - uart2_clk: uart2-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &twd_timer {
@@ -43,5 +37,4 @@ &timer { &uart2 { status = "okay"; - clocks = <&uart2_clk>; };
arch/arm/boot/dts/owl-s500-sparky.dts +0 -7
@@ -25,12 +25,6 @@ memory@0 { device_type = "memory"; reg = <0x0 0x40000000>; /* 1 or 2 GiB */ }; - - uart3_clk: uart3-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &timer {
@@ -39,5 +33,4 @@ &timer { &uart3 { status = "okay"; - clocks = <&uart3_clk>; };
arch/arm/boot/dts/owl-s500.dtsi +7 -0
@@ -131,6 +131,7 @@ uart0: serial@b0120000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0120000 0x2000>; interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART0>; status = "disabled"; };
@@ -138,6 +139,7 @@ uart1: serial@b0122000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0122000 0x2000>; interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART1>; status = "disabled"; };
@@ -145,6 +147,7 @@ uart2: serial@b0124000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0124000 0x2000>; interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART2>; status = "disabled"; };
@@ -152,6 +155,7 @@ uart3: serial@b0126000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0126000 0x2000>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART3>; status = "disabled"; };
@@ -159,6 +163,7 @@ uart4: serial@b0128000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0128000 0x2000>; interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART4>; status = "disabled"; };
@@ -166,6 +171,7 @@ uart5: serial@b012a000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb012a000 0x2000>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART5>; status = "disabled"; };
@@ -173,6 +179,7 @@ uart6: serial@b012c000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb012c000 0x2000>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART6>; status = "disabled"; };
Signature · 1 line
2.30.0
PATCH v3 3/13 arm: dts: owl-s500: Add Reset controller
In reply to Cristian CiocalteaAdd reset controller property and bindings header for the Actions Semi S500 SoC DTS.
---
Changes in v3:
- Added Reviewed-by from Mani
arch/arm/boot/dts/owl-s500.dtsi | 2 ++ 1 file changed, 2 insertions(+)
arch/arm/boot/dts/owl-s500.dtsi +2 -0
@@ -8,6 +8,7 @@ #include <dt-bindings/clock/actions,s500-cmu.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/power/owl-s500-powergate.h> +#include <dt-bindings/reset/actions,s500-reset.h> / { compatible = "actions,s500";
@@ -188,6 +189,7 @@ cmu: clock-controller@b0160000 { reg = <0xb0160000 0x8000>; clocks = <&hosc>, <&losc>; #clock-cells = <1>; + #reset-cells = <1>; }; timer: timer@b0168000 {
Signature · 1 line
2.30.0
PATCH v3 4/13 dt-bindings: dma: owl: Add compatible string for Actions Semi S500 SoC
In reply to Cristian CiocalteaAdd a new compatible string corresponding to the DMA controller found in the S500 variant of the Actions Semi Owl SoCs family. Additionally, order the entries alphabetically.
---
Changes in v3:
- Added Reviewed-by tags from Mani and Rob
- Ordered the entries per Mani's suggestion
Documentation/devicetree/bindings/dma/owl-dma.yaml | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
Documentation/devicetree/bindings/dma/owl-dma.yaml +4 -3
@@ -8,8 +8,8 @@ title: Actions Semi Owl SoCs DMA controller description: | The OWL DMA is a general-purpose direct memory access controller capable of - supporting 10 and 12 independent DMA channels for S700 and S900 SoCs - respectively. + supporting 10 independent DMA channels for the Actions Semi S700 SoC and 12 + independent DMA channels for the S500 and S900 SoC variants. maintainers: - Manivannan Sadhasivam <[email protected]>
@@ -20,8 +20,9 @@ allOf: properties: compatible: enum: - - actions,s900-dma + - actions,s500-dma - actions,s700-dma + - actions,s900-dma reg: maxItems: 1
Signature · 1 line
2.30.0
PATCH v3 6/13 arm: dts: owl-s500: Add DMA controller
In reply to Cristian CiocalteaAdd DMA controller node for Actions Semi S500 SoC.
---
Changes in v3:
- Added Reviewed-by from Mani
arch/arm/boot/dts/owl-s500.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
arch/arm/boot/dts/owl-s500.dtsi +14 -0
@@ -207,5 +207,19 @@ sps: power-controller@b01b0100 { reg = <0xb01b0100 0x100>; #power-domain-cells = <1>; }; + + dma: dma-controller@b0260000 { + compatible = "actions,s500-dma"; + reg = <0xb0260000 0xd00>; + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + dma-channels = <12>; + dma-requests = <46>; + clocks = <&cmu CLK_DMAC>; + power-domains = <&sps S500_PD_DMA>; + }; }; };
Signature · 1 line
2.30.0
PATCH v3 5/13 dmaengine: owl: Add compatible for the Actions Semi S500 DMA controller
In reply to Cristian CiocalteaThe DMA controller present on the Actions Semi S500 SoC is compatible with the S900 variant, so add it to the list of devices supported by the Actions Semi Owl DMA driver. Additionally, order the entries alphabetically.
---
Changes in v3:
- Added Reviewed-by from Mani
- Ordered the entries to be consistent with the related dt-bindings
drivers/dma/owl-dma.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/dma/owl-dma.c +2 -1
@@ -1080,8 +1080,9 @@ static struct dma_chan *owl_dma_of_xlate(struct of_phandle_args *dma_spec, }static const struct of_device_id owl_dma_match[] = { - { .compatible ="actions,s900-dma" , .data = (void *)S900_DMA ,}, + { .compatible ="actions,s500-dma" , .data = (void *)S900_DMA ,}, { .compatible ="actions,s700-dma" , .data = (void *)S700_DMA ,}, + { .compatible ="actions,s900-dma" , .data = (void *)S900_DMA ,}, {/* sentinel */ }, };MODULE_DEVICE_TABLE (of, owl_dma_match);
Signature · 1 line
2.30.0
PATCH v3 9/13 arm: dts: owl-s500: Add I2C support
In reply to Cristian CiocalteaAdd I2C controller nodes for Actions Semi S500 SoC.
---
Changes in v3:
- Added Reviewed-by from Mani
arch/arm/boot/dts/owl-s500.dtsi | 40 +++++++++++++++++++++++++++++++++ 1 file changed, 40 insertions(+)
arch/arm/boot/dts/owl-s500.dtsi +40 -0
@@ -193,6 +193,46 @@ cmu: clock-controller@b0160000 { #reset-cells = <1>; }; + i2c0: i2c@b0170000 { + compatible = "actions,s500-i2c"; + reg = <0xb0170000 0x4000>; + clocks = <&cmu CLK_I2C0>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@b0174000 { + compatible = "actions,s500-i2c"; + reg = <0xb0174000 0x4000>; + clocks = <&cmu CLK_I2C1>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@b0178000 { + compatible = "actions,s500-i2c"; + reg = <0xb0178000 0x4000>; + clocks = <&cmu CLK_I2C2>; + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@b017c000 { + compatible = "actions,s500-i2c"; + reg = <0xb017c000 0x4000>; + clocks = <&cmu CLK_I2C3>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + timer: timer@b0168000 { compatible = "actions,s500-timer"; reg = <0xb0168000 0x8000>;
Signature · 1 line
2.30.0
PATCH v3 10/13 arm: dts: owl-s500: Add SIRQ controller
In reply to Cristian CiocalteaAdd SIRQ controller node for Actions Semi S500 SoC.
---
Changes in v3:
- Added Reviewed-by from Mani
arch/arm/boot/dts/owl-s500.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+)
arch/arm/boot/dts/owl-s500.dtsi +10 -0
@@ -233,6 +233,16 @@ i2c3: i2c@b017c000 { status = "disabled"; }; + sirq: interrupt-controller@b01b0200 { + compatible = "actions,s500-sirq"; + reg = <0xb01b0200 0x4>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, /* SIRQ0 */ + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, /* SIRQ1 */ + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; /* SIRQ2 */ + }; + timer: timer@b0168000 { compatible = "actions,s500-timer"; reg = <0xb0168000 0x8000>;
Signature · 1 line
2.30.0
PATCH v3 7/13 arm: dts: owl-s500: Add pinctrl & GPIO support
In reply to Cristian CiocalteaAdd pinctrl node for Actions Semi S500 SoC.
---
Changes in v3:
- Added Reviewed-by from Mani
arch/arm/boot/dts/owl-s500.dtsi | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+)
arch/arm/boot/dts/owl-s500.dtsi +20 -0
@@ -6,6 +6,7 @@ */ #include <dt-bindings/clock/actions,s500-cmu.h> +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/power/owl-s500-powergate.h> #include <dt-bindings/reset/actions,s500-reset.h>
@@ -208,6 +209,25 @@ sps: power-controller@b01b0100 { #power-domain-cells = <1>; }; + pinctrl: pinctrl@b01b0000 { + compatible = "actions,s500-pinctrl"; + reg = <0xb01b0000 0x40>, /* GPIO */ + <0xb01b0040 0x10>, /* Multiplexing Control */ + <0xb01b0060 0x18>, /* PAD Control */ + <0xb01b0080 0xc>; /* PAD Drive Capacity */ + clocks = <&cmu CLK_GPIO>; + gpio-controller; + gpio-ranges = <&pinctrl 0 0 132>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, /* GPIOA */ + <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, /* GPIOB */ + <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, /* GPIOC */ + <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, /* GPIOD */ + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; /* GPIOE */ + }; + dma: dma-controller@b0260000 { compatible = "actions,s500-dma"; reg = <0xb0260000 0xd00>;
Signature · 1 line
2.30.0
PATCH v3 8/13 arm: dts: owl-s500: Add MMC support
In reply to Cristian CiocalteaAdd MMC controller nodes for Actions Semi S500 SoC, in order to facilitate access to SD/EMMC/SDIO cards.
---
Changes in v3:
- Added Reviewed-by tags from Ulf and Mani
arch/arm/boot/dts/owl-s500.dtsi | 33 +++++++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+)
arch/arm/boot/dts/owl-s500.dtsi +33 -0
@@ -241,5 +241,38 @@ dma: dma-controller@b0260000 { clocks = <&cmu CLK_DMAC>; power-domains = <&sps S500_PD_DMA>; }; + + mmc0: mmc@b0230000 { + compatible = "actions,s500-mmc", "actions,owl-mmc"; + reg = <0xb0230000 0x38>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_SD0>; + resets = <&cmu RESET_SD0>; + dmas = <&dma 2>; + dma-names = "mmc"; + status = "disabled"; + }; + + mmc1: mmc@b0234000 { + compatible = "actions,s500-mmc", "actions,owl-mmc"; + reg = <0xb0234000 0x38>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_SD1>; + resets = <&cmu RESET_SD1>; + dmas = <&dma 3>; + dma-names = "mmc"; + status = "disabled"; + }; + + mmc2: mmc@b0238000 { + compatible = "actions,s500-mmc", "actions,owl-mmc"; + reg = <0xb0238000 0x38>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_SD2>; + resets = <&cmu RESET_SD2>; + dmas = <&dma 4>; + dma-names = "mmc"; + status = "disabled"; + }; }; };
Signature · 1 line
2.30.0
PATCH v3 11/13 arm: dts: owl-s500-roseapplepi: Add uSD support
In reply to Cristian CiocalteaAdd uSD support for RoseapplePi SBC using a fixed regulator as a temporary solution until PMIC support becomes available.
---
Changes in v3:
- None
arch/arm/boot/dts/owl-s500-roseapplepi.dts | 50 ++++++++++++++++++++++ 1 file changed, 50 insertions(+)
arch/arm/boot/dts/owl-s500-roseapplepi.dts +50 -0
@@ -14,6 +14,7 @@ / { model = "Roseapple Pi"; aliases { + mmc0 = &mmc0; serial2 = &uart2; };
@@ -25,6 +26,55 @@ memory@0 { device_type = "memory"; reg = <0x0 0x80000000>; /* 2GB */ }; + + /* Fixed regulator used in the absence of PMIC */ + sd_vcc: sd-vcc { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.1V"; + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-always-on; + }; +}; + +&pinctrl { + mmc0_pins: mmc0-pins { + pinmux { + groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp", + "sd0_cmd_mfp", "sd0_clk_mfp"; + function = "sd0"; + }; + + drv-pinconf { + groups = "sd0_d0_d3_drv", "sd0_cmd_drv", "sd0_clk_drv"; + drive-strength = <8>; + }; + + bias0-pinconf { + pins = "sd0_d0", "sd0_d1", "sd0_d2", + "sd0_d3", "sd0_cmd"; + bias-pull-up; + }; + + bias1-pinconf { + pins = "sd0_clk"; + bias-pull-down; + }; + }; +}; + +/* uSD */ +&mmc0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + no-sdio; + no-mmc; + no-1-8-v; + cd-gpios = <&pinctrl 117 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <&sd_vcc>; + vqmmc-supply = <&sd_vcc>; }; &twd_timer {
Signature · 1 line
2.30.0
PATCH v3 12/13 arm: dts: owl-s500-roseapplepi: Add I2C pinctrl configuration
In reply to Cristian CiocalteaAdd pinctrl definitions for the I2C controllers used in RoseapplePi SBC. For the moment enable only I2C0, which is used by the ATC2603C PMIC.
---
Changes in v3:
- Added Reviewed-by from Mani
arch/arm/boot/dts/owl-s500-roseapplepi.dts | 44 ++++++++++++++++++++++ 1 file changed, 44 insertions(+)
arch/arm/boot/dts/owl-s500-roseapplepi.dts +44 -0
@@ -37,7 +37,51 @@ sd_vcc: sd-vcc { }; }; +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; +}; + +&i2c1 { + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; +}; + +&i2c2 { + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; +}; + &pinctrl { + i2c0_pins: i2c0-pins { + pinmux { + groups = "i2c0_mfp"; + function = "i2c0"; + }; + + pinconf { + pins = "i2c0_sclk", "i2c0_sdata"; + bias-pull-up; + }; + }; + + i2c1_pins: i2c1-pins { + pinconf { + pins = "i2c1_sclk", "i2c1_sdata"; + bias-pull-up; + }; + }; + + i2c2_pins: i2c2-pins { + pinconf { + pins = "i2c2_sclk", "i2c2_sdata"; + bias-pull-up; + }; + }; + mmc0_pins: mmc0-pins { pinmux { groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp",
Signature · 1 line
2.30.0
PATCH v3 13/13 MAINTAINERS: Add linux-actions ML for Actions Semi Arch
In reply to Cristian CiocalteaAdd the linux-actions mailing list for the Actions Semi architecture.
---
Changes in v3:
- Added Reviewed-by from Mani
MAINTAINERS | 1 + 1 file changed, 1 insertion(+)
MAINTAINERS +1 -0
@@ -1512,6 +1512,7 @@ ARM/ACTIONS SEMI ARCHITECTURE M: Andreas Färber <[email protected]> M: Manivannan Sadhasivam <[email protected]> L: [email protected] (moderated for non-subscribers) +L: [email protected] (moderated for non-subscribers) S: Maintained F: Documentation/devicetree/bindings/arm/actions.yaml F: Documentation/devicetree/bindings/clock/actions,owl-cmu.txt
Signature · 1 line
2.30.0
Re: [PATCH v3 11/13] arm: dts: owl-s500-roseapplepi: Add uSD support
In reply to Cristian CiocalteaQuoted 4 lines · Cristian Ciocaltea
Add uSD support for RoseapplePi SBC using a fixed regulator as a temporary solution until PMIC support becomes available.
Signed-off-by Cristian Ciocaltea <[email protected]>
Thanks,
Mani
Quoted 78 lines
---
Changes in v3:
- Nonearch/arm/boot/dts/owl-s500-roseapplepi.dts | 50 ++++++++++++++++++++++ 1 file changed, 50 insertions(+)arch/arm/boot/dts/owl-s500-roseapplepi.dts +50
-0@@ -14,6 +14,7 @@ / { model = "Roseapple Pi"; aliases { + mmc0 = &mmc0; serial2 = &uart2; };@@ -25,6 +26,55 @@ memory@0 { device_type = "memory"; reg = <0x0 0x80000000>; /* 2GB */ }; + + /* Fixed regulator used in the absence of PMIC */ + sd_vcc: sd-vcc { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.1V"; + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-always-on; + }; +}; + +&pinctrl { + mmc0_pins: mmc0-pins { + pinmux { + groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp", + "sd0_cmd_mfp", "sd0_clk_mfp"; + function = "sd0"; + }; + + drv-pinconf { + groups = "sd0_d0_d3_drv", "sd0_cmd_drv", "sd0_clk_drv"; + drive-strength = <8>; + }; + + bias0-pinconf { + pins = "sd0_d0", "sd0_d1", "sd0_d2", + "sd0_d3", "sd0_cmd"; + bias-pull-up; + }; + + bias1-pinconf { + pins = "sd0_clk"; + bias-pull-down; + }; + }; +}; + +/* uSD */ +&mmc0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + no-sdio; + no-mmc; + no-1-8-v; + cd-gpios = <&pinctrl 117 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <&sd_vcc>; + vqmmc-supply = <&sd_vcc>; }; &twd_timer {Signature · 1 line
2.30.0
Quoted 6 lines · Cristian Ciocaltea
Hi,
This patchset brings a series of improvements for the Actions Semi S500 SoCs family, by adding support for Clock & Reset Management Units, DMA, MMC, I2C & SIRQ controllers.
Quoted 7 lines
Please note the patches consist mostly of DTS and bindings/compatibles changes, since all the work they depend on has been already merged, i.e. clock fixes/additions, pinctrl driver, sirq driver.
For the moment, I have only enabled the features I could test on RoseapplePi SBC.
Applied all patches except the 2 dmaengine patches for v5.12. Andreas, please let me know if you want to do the PR this time. Else I'll proceed.
Thanks,
Mani
Quoted 48 lines
Thanks,
CristiChanges in v3:
- Squashed 'arm: dts: owl-s500-roseapplepi: Use UART clock from CMU' with 'arm: dts: owl-s500: Set CMU clocks for UARTs', according to Mani's review
- Rebased series on v5.11-rc1 and dropped the already merged patches:
* dt-bindings: mmc: owl: Add compatible string for Actions Semi S500 SoC
* dt-bindings: i2c: owl: Convert Actions Semi Owl binding to a schema
*MAINTAINERS: Update entry for Actions Semi Owl I2C binding
* i2c: owl: Add compatible for the Actions Semi S500 I2C controllerChanges in v2:
- Added new bindings/compatibles for S500 DMA, MMC & I2C controllers
- Added support for the SIRQ controller
- Added new entries inMAINTAINERS
- Updated naming of some patches in v1Cristian Ciocaltea (13):
arm: dts: owl-s500: Add Clock Management Unit
arm: dts: owl-s500: Set CMU clocks for UARTs
arm: dts: owl-s500: Add Reset controller
dt-bindings: dma: owl: Add compatible string for Actions Semi S500 SoC
dmaengine: owl: Add compatible for the Actions Semi S500 DMA
controller
arm: dts: owl-s500: Add DMA controller
arm: dts: owl-s500: Add pinctrl & GPIO support
arm: dts: owl-s500: Add MMC support
arm: dts: owl-s500: Add I2C support
arm: dts: owl-s500: Add SIRQ controller
arm: dts: owl-s500-roseapplepi: Add uSD support
arm: dts: owl-s500-roseapplepi: Add I2C pinctrl configuration
MAINTAINERS: Add linux-actions ML for Actions Semi Arch.../devicetree/bindings/dma/owl-dma.yaml | 7 +- MAINTAINERS | 1 + arch/arm/boot/dts/owl-s500-cubieboard6.dts | 7 - .../arm/boot/dts/owl-s500-guitar-bb-rev-b.dts | 7 - .../arm/boot/dts/owl-s500-labrador-base-m.dts | 7 - arch/arm/boot/dts/owl-s500-roseapplepi.dts | 97 +++++++++++- arch/arm/boot/dts/owl-s500-sparky.dts | 7 - arch/arm/boot/dts/owl-s500.dtsi | 140 ++++++++++++++++++ drivers/dma/owl-dma.c | 3 +- 9 files changed, 239 insertions(+), 37 deletions(-)Signature · 1 line
2.30.0
Re: [PATCH v3 11/13] arm: dts: owl-s500-roseapplepi: Add uSD support
In reply to Manivannan SadhasivamQuoted 7 lines · Manivannan Sadhasivam
Quoted 4 lines · Cristian Ciocaltea
Add uSD support for RoseapplePi SBC using a fixed regulator as a temporary solution until PMIC support becomes available.
Signed-off-by Cristian Ciocaltea <[email protected]>Reviewed-by Manivannan Sadhasivam <[email protected]>
Thank you, Mani!
Quoted 81 lines
Thanks,
ManiQuoted 78 lines
---
Changes in v3:
- Nonearch/arm/boot/dts/owl-s500-roseapplepi.dts | 50 ++++++++++++++++++++++ 1 file changed, 50 insertions(+)arch/arm/boot/dts/owl-s500-roseapplepi.dts +50
-0@@ -14,6 +14,7 @@ / { model = "Roseapple Pi"; aliases { + mmc0 = &mmc0; serial2 = &uart2; };@@ -25,6 +26,55 @@ memory@0 { device_type = "memory"; reg = <0x0 0x80000000>; /* 2GB */ }; + + /* Fixed regulator used in the absence of PMIC */ + sd_vcc: sd-vcc { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.1V"; + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-always-on; + }; +}; + +&pinctrl { + mmc0_pins: mmc0-pins { + pinmux { + groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp", + "sd0_cmd_mfp", "sd0_clk_mfp"; + function = "sd0"; + }; + + drv-pinconf { + groups = "sd0_d0_d3_drv", "sd0_cmd_drv", "sd0_clk_drv"; + drive-strength = <8>; + }; + + bias0-pinconf { + pins = "sd0_d0", "sd0_d1", "sd0_d2", + "sd0_d3", "sd0_cmd"; + bias-pull-up; + }; + + bias1-pinconf { + pins = "sd0_clk"; + bias-pull-down; + }; + }; +}; + +/* uSD */ +&mmc0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + no-sdio; + no-mmc; + no-1-8-v; + cd-gpios = <&pinctrl 117 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <&sd_vcc>; + vqmmc-supply = <&sd_vcc>; }; &twd_timer {Signature · 1 line
2.30.0
Quoted 11 lines · Manivannan Sadhasivam
Quoted 10 lines · Cristian Ciocaltea
Hi,
This patchset brings a series of improvements for the Actions Semi S500 SoCs family, by adding support for Clock & Reset Management Units, DMA, MMC, I2C & SIRQ controllers.
Please note the patches consist mostly of DTS and bindings/compatibles changes, since all the work they depend on has been already merged, i.e. clock fixes/additions, pinctrl driver, sirq driver.
Quoted 6 lines
Quoted 3 lines
For the moment, I have only enabled the features I could test on RoseapplePi SBC.
Applied all patches except the 2 dmaengine patches for v5.12. Andreas, please let me know if you want to do the PR this time. Else I'll proceed.
Thank you, Mani!
The dmaengine patches should be picked up by Vinod, right?
Quoted 51 lines
Thanks,
ManiQuoted 48 lines
Thanks,
CristiChanges in v3:
- Squashed 'arm: dts: owl-s500-roseapplepi: Use UART clock from CMU' with 'arm: dts: owl-s500: Set CMU clocks for UARTs', according to Mani's review
- Rebased series on v5.11-rc1 and dropped the already merged patches:
* dt-bindings: mmc: owl: Add compatible string for Actions Semi S500 SoC
* dt-bindings: i2c: owl: Convert Actions Semi Owl binding to a schema
*MAINTAINERS: Update entry for Actions Semi Owl I2C binding
* i2c: owl: Add compatible for the Actions Semi S500 I2C controllerChanges in v2:
- Added new bindings/compatibles for S500 DMA, MMC & I2C controllers
- Added support for the SIRQ controller
- Added new entries inMAINTAINERS
- Updated naming of some patches in v1Cristian Ciocaltea (13):
arm: dts: owl-s500: Add Clock Management Unit
arm: dts: owl-s500: Set CMU clocks for UARTs
arm: dts: owl-s500: Add Reset controller
dt-bindings: dma: owl: Add compatible string for Actions Semi S500 SoC
dmaengine: owl: Add compatible for the Actions Semi S500 DMA
controller
arm: dts: owl-s500: Add DMA controller
arm: dts: owl-s500: Add pinctrl & GPIO support
arm: dts: owl-s500: Add MMC support
arm: dts: owl-s500: Add I2C support
arm: dts: owl-s500: Add SIRQ controller
arm: dts: owl-s500-roseapplepi: Add uSD support
arm: dts: owl-s500-roseapplepi: Add I2C pinctrl configuration
MAINTAINERS: Add linux-actions ML for Actions Semi Arch.../devicetree/bindings/dma/owl-dma.yaml | 7 +- MAINTAINERS | 1 + arch/arm/boot/dts/owl-s500-cubieboard6.dts | 7 - .../arm/boot/dts/owl-s500-guitar-bb-rev-b.dts | 7 - .../arm/boot/dts/owl-s500-labrador-base-m.dts | 7 - arch/arm/boot/dts/owl-s500-roseapplepi.dts | 97 +++++++++++- arch/arm/boot/dts/owl-s500-sparky.dts | 7 - arch/arm/boot/dts/owl-s500.dtsi | 140 ++++++++++++++++++ drivers/dma/owl-dma.c | 3 +- 9 files changed, 239 insertions(+), 37 deletions(-)Signature · 1 line
2.30.0
Quoted 19 lines · Cristian Ciocaltea
Quoted 4 lines · Manivannan Sadhasivam
Quoted 3 lines · Cristian Ciocaltea
Hi,
This patchset brings a series of improvements for the Actions Semi
S500
Quoted 1 line
Quoted 1 line
SoCs family, by adding support for Clock & Reset Management Units,
DMA,
Quoted 3 lines
Quoted 3 lines
MMC, I2C & SIRQ controllers.
Please note the patches consist mostly of DTS and
bindings/compatibles
Quoted 7 lines
Quoted 6 lines
changes, since all the work they depend on has been already merged, i.e. clock fixes/additions, pinctrl driver, sirq driver.
For the moment, I have only enabled the features I could test on RoseapplePi SBC.
Quoted 7 lines
Quoted 1 line
Applied all patches except the 2 dmaengine patches for v5.12.
Andreas, please
Quoted 1 line
let me know if you want to do the PR this time. Else I'll proceed.
Thank you, Mani!
The dmaengine patches should be picked up by Vinod, right?
Yes! Vinod is just back from vacation, so he will :)
Thanks,
Mani
Quoted 60 lines
Quoted 8 lines
Thanks,
ManiQuoted 5 lines
Thanks,
CristiChanges in v3:
- Squashed 'arm: dts: owl-s500-roseapplepi: Use UART clock fromCMU' with
Quoted 1 line
Quoted 1 line
'arm: dts: owl-s500: Set CMU clocks for UARTs', according to
Mani's review
Quoted 1 line
Quoted 1 line
- Rebased series on v5.11-rc1 and dropped the already merged
patches:
Quoted 1 line
Quoted 1 line
* dt-bindings: mmc: owl: Add compatible string for Actions Semi
S500 SoC
Quoted 1 line
Quoted 1 line
* dt-bindings: i2c: owl: Convert Actions Semi Owl binding to a
schema
Quoted 2 lines
Quoted 2 lines
*
MAINTAINERS: Update entry for Actions Semi Owl I2C binding
* i2c: owl: Add compatible for the Actions Semi S500 I2Ccontroller
Quoted 3 lines
Quoted 3 lines
Changes in v2:
- Added new bindings/compatibles for S500 DMA, MMC & I2Ccontrollers
Quoted 9 lines
Quoted 9 lines
- Added support for the SIRQ controller
- Added new entries inMAINTAINERS
- Updated naming of some patches in v1Cristian Ciocaltea (13):
arm: dts: owl-s500: Add Clock Management Unit
arm: dts: owl-s500: Set CMU clocks for UARTs
arm: dts: owl-s500: Add Reset controller
dt-bindings: dma: owl: Add compatible string for Actions SemiS500 SoC
Quoted 11 lines
Quoted 11 lines
dmaengine: owl: Add compatible for the Actions Semi S500 DMA
controller
arm: dts: owl-s500: Add DMA controller
arm: dts: owl-s500: Add pinctrl & GPIO support
arm: dts: owl-s500: Add MMC support
arm: dts: owl-s500: Add I2C support
arm: dts: owl-s500: Add SIRQ controller
arm: dts: owl-s500-roseapplepi: Add uSD support
arm: dts: owl-s500-roseapplepi: Add I2C pinctrl configuration
MAINTAINERS: Add linux-actions ML for Actions Semi ArchQuoted 8 lines
Quoted 8 lines
.../devicetree/bindings/dma/owl-dma.yaml | 7 +- MAINTAINERS | 1 + arch/arm/boot/dts/owl-s500-cubieboard6.dts | 7 - .../arm/boot/dts/owl-s500-guitar-bb-rev-b.dts | 7 - .../arm/boot/dts/owl-s500-labrador-base-m.dts | 7 - arch/arm/boot/dts/owl-s500-roseapplepi.dts | 97 +++++++++++- arch/arm/boot/dts/owl-s500-sparky.dts | 7 - arch/arm/boot/dts/owl-s500.dtsi | 140++++++++++++++++++
Quoted 6 lines
Quoted 6 lines
drivers/dma/owl-dma.c | 3 +- 9 files changed, 239 insertions(+), 37 deletions(-)Signature · 1 line
2.30.0
Signature · 1 line
Sent from my Android device with K-9 Mail. Please excuse my brevity.
Re: [PATCH v3 04/13] dt-bindings: dma: owl: Add compatible string for Actions Semi S500 SoC
In reply to Cristian CiocalteaQuoted 3 lines · Cristian Ciocaltea
Add a new compatible string corresponding to the DMA controller found in the S500 variant of the Actions Semi Owl SoCs family. Additionally, order the entries alphabetically.
Applied, thanks
Signature · 1 line
~Vinod
Re: [PATCH v3 05/13] dmaengine: owl: Add compatible for the Actions Semi S500 DMA controller
In reply to Cristian CiocalteaQuoted 4 lines · Cristian Ciocaltea
The DMA controller present on the Actions Semi S500 SoC is compatible with the S900 variant, so add it to the list of devices supported by the Actions Semi Owl DMA driver. Additionally, order the entries alphabetically.
Applied, thanks
Signature · 1 line
~Vinod
Re: [PATCH v3 01/13] arm: dts: owl-s500: Add Clock Management Unit
In reply to Cristian CiocalteaEm 12/29/2020 6:17 PM, Cristian Ciocaltea escreveu:
Quoted 41 lines
Add Clock Management Unit for Actions Semi S500 SoC.
Signed-off-by Cristian Ciocaltea <[email protected]>Reviewed-by Manivannan Sadhasivam <[email protected]>---
Changes in v3:
- Added Reviewed-by from Maniarch/arm/boot/dts/owl-s500.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+)arch/arm/boot/dts/owl-s500.dtsi +7
-0@@ -5,6 +5,7 @@ * Copyright (c) 2016-2017 Andreas Färber */ +#include <dt-bindings/clock/actions,s500-cmu.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/power/owl-s500-powergate.h>@@ -70,6 +71,12 @@ hosc: hosc { #clock-cells = <0>; }; + losc: losc { + compatible = "fixed-clock"; + clock-frequency = <32768>; + #clock-cells = <0>; + }; + soc { compatible = "simple-bus"; #address-cells = <1>;@@ -169,6 +176,13 @@ uart6: serial@b012c000 { status = "disabled"; };
arch/arm/boot/dts/owl-s500.dtsi uart6: serial@b012c000 { · line 188
Quoted 10 lines
arch/arm/boot/dts/owl-s500.dtsi +7
-0+ cmu: clock-controller@b0160000 { + compatible = "actions,s500-cmu"; + reg = <0xb0160000 0x8000>; + clocks = <&hosc>, <&losc>; + #clock-cells = <1>; + }; + timer: timer@b0168000 { compatible = "actions,s500-timer"; reg = <0xb0168000 0x8000>;
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH v3 02/13] arm: dts: owl-s500: Set CMU clocks for UARTs
In reply to Cristian CiocalteaEm 12/29/2020 6:17 PM, Cristian Ciocaltea escreveu:
Quoted 182 lines
Set Clock Management Unit clocks for the UART nodes of Actions Semi S500 SoCs and remove the dummy "
uart2_clk" and "uart3_clk" fixed clocks.Signed-off-by Cristian Ciocaltea <[email protected]>Reviewed-by Manivannan Sadhasivam <[email protected]>---
Changes in v3:
- Added Reviewed-by from Mani
- Removed the dummy 'uart2_clk' and 'uart3_clk' nodes from all owl-s500 DTS, per Mani's reviewarch/arm/boot/dts/owl-s500-cubieboard6.dts | 7 ------- arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts | 7 ------- arch/arm/boot/dts/owl-s500-labrador-base-m.dts | 7 ------- arch/arm/boot/dts/owl-s500-roseapplepi.dts | 7 ------- arch/arm/boot/dts/owl-s500-sparky.dts | 7 ------- arch/arm/boot/dts/owl-s500.dtsi | 7 +++++++ 6 files changed, 7 insertions(+), 35 deletions(-)arch/arm/boot/dts/owl-s500-cubieboard6.dts +0
-7@@ -25,12 +25,6 @@ memory@0 { device_type = "memory"; reg = <0x0 0x80000000>; }; - - uart3_clk: uart3-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &timer {@@ -39,5 +33,4 @@ &timer { &uart3 { status = "okay"; - clocks = <&uart3_clk>; };arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts +0
-7@@ -18,15 +18,8 @@ aliases { chosen { stdout-path = "serial3:115200n8"; }; - - uart3_clk: uart3-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &uart3 { status = "okay"; - clocks = <&uart3_clk>; };arch/arm/boot/dts/owl-s500-labrador-base-m.dts +0
-7@@ -21,15 +21,8 @@ aliases { chosen { stdout-path = "serial3:115200n8"; }; - - uart3_clk: uart3-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &uart3 { status = "okay"; - clocks = <&uart3_clk>; };arch/arm/boot/dts/owl-s500-roseapplepi.dts +0
-7@@ -25,12 +25,6 @@ memory@0 { device_type = "memory"; reg = <0x0 0x80000000>; /* 2GB */ }; - - uart2_clk: uart2-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &twd_timer {@@ -43,5 +37,4 @@ &timer { &uart2 { status = "okay"; - clocks = <&uart2_clk>; };arch/arm/boot/dts/owl-s500-sparky.dts +0
-7@@ -25,12 +25,6 @@ memory@0 { device_type = "memory"; reg = <0x0 0x40000000>; /* 1 or 2 GiB */ }; - - uart3_clk: uart3-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &timer {@@ -39,5 +33,4 @@ &timer { &uart3 { status = "okay"; - clocks = <&uart3_clk>; };arch/arm/boot/dts/owl-s500.dtsi +6
-0@@ -131,6 +131,7 @@ uart0: serial@b0120000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0120000 0x2000>; interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART0>; status = "disabled"; };@@ -138,6 +139,7 @@ uart1: serial@b0122000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0122000 0x2000>; interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART1>; status = "disabled"; };@@ -145,6 +147,7 @@ uart2: serial@b0124000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0124000 0x2000>; interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART2>; status = "disabled"; };@@ -152,6 +155,7 @@ uart3: serial@b0126000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0126000 0x2000>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART3>; status = "disabled"; };@@ -159,6 +163,7 @@ uart4: serial@b0128000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0128000 0x2000>; interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART4>; status = "disabled"; };@@ -166,6 +171,7 @@ uart5: serial@b012a000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb012a000 0x2000>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART5>; status = "disabled"; };
arch/arm/boot/dts/owl-s500.dtsi uart6: serial@b012c000 { · line 185
Quoted 7 lines
arch/arm/boot/dts/owl-s500.dtsi +1
-0@@ -173,6 +179,7 @@ uart6: serial@b012c000 { compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb012c000 0x2000>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART6>; status = "disabled"; };
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH v3 03/13] arm: dts: owl-s500: Add Reset controller
In reply to Cristian CiocalteaEm 12/29/2020 6:17 PM, Cristian Ciocaltea escreveu:
Quoted 26 lines
Add reset controller property and bindings header for the Actions Semi S500 SoC DTS.
Signed-off-by Cristian Ciocaltea <[email protected]>Reviewed-by Manivannan Sadhasivam <[email protected]>---
Changes in v3:
- Added Reviewed-by from Maniarch/arm/boot/dts/owl-s500.dtsi | 2 ++ 1 file changed, 2 insertions(+)arch/arm/boot/dts/owl-s500.dtsi +1
-0@@ -8,6 +8,7 @@ #include <dt-bindings/clock/actions,s500-cmu.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/power/owl-s500-powergate.h> +#include <dt-bindings/reset/actions,s500-reset.h> / { compatible = "actions,s500";
arch/arm/boot/dts/owl-s500.dtsi cmu: clock-controller@b0160000 { · line 195
Quoted 7 lines
arch/arm/boot/dts/owl-s500.dtsi +1
-0@@ -188,6 +189,7 @@ cmu: clock-controller@b0160000 { reg = <0xb0160000 0x8000>; clocks = <&hosc>, <&losc>; #clock-cells = <1>; + #reset-cells = <1>; }; timer: timer@b0168000 {
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH v3 06/13] arm: dts: owl-s500: Add DMA controller
In reply to Cristian CiocalteaEm 12/29/2020 6:17 PM, Cristian Ciocaltea escreveu:
Quoted 26 lines
Add DMA controller node for Actions Semi S500 SoC.
Signed-off-by Cristian Ciocaltea <[email protected]>Reviewed-by Manivannan Sadhasivam <[email protected]>---
Changes in v3:
- Added Reviewed-by from Maniarch/arm/boot/dts/owl-s500.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+)arch/arm/boot/dts/owl-s500.dtsi +6
-0@@ -207,5 +207,19 @@ sps: power-controller@b01b0100 { reg = <0xb01b0100 0x100>; #power-domain-cells = <1>; }; + + dma: dma-controller@b0260000 { + compatible = "actions,s500-dma"; + reg = <0xb0260000 0xd00>; + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
arch/arm/boot/dts/owl-s500.dtsi sps: power-controller@b01b0100 { · line 225
Quoted 10 lines
arch/arm/boot/dts/owl-s500.dtsi +8
-0+ <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + dma-channels = <12>; + dma-requests = <46>; + clocks = <&cmu CLK_DMAC>; + power-domains = <&sps S500_PD_DMA>; + }; }; };
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH v3 07/13] arm: dts: owl-s500: Add pinctrl & GPIO support
In reply to Cristian CiocalteaEm 12/29/2020 6:17 PM, Cristian Ciocaltea escreveu:
Quoted 40 lines
Add pinctrl node for Actions Semi S500 SoC.
Signed-off-by Cristian Ciocaltea <[email protected]>Reviewed-by Manivannan Sadhasivam <[email protected]>---
Changes in v3:
- Added Reviewed-by from Maniarch/arm/boot/dts/owl-s500.dtsi | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+)arch/arm/boot/dts/owl-s500.dtsi +13
-0@@ -6,6 +6,7 @@ */ #include <dt-bindings/clock/actions,s500-cmu.h> +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/power/owl-s500-powergate.h> #include <dt-bindings/reset/actions,s500-reset.h>@@ -208,6 +209,25 @@ sps: power-controller@b01b0100 { #power-domain-cells = <1>; }; + pinctrl: pinctrl@b01b0000 { + compatible = "actions,s500-pinctrl"; + reg = <0xb01b0000 0x40>, /* GPIO */ + <0xb01b0040 0x10>, /* Multiplexing Control */ + <0xb01b0060 0x18>, /* PAD Control */ + <0xb01b0080 0xc>; /* PAD Drive Capacity */ + clocks = <&cmu CLK_GPIO>; + gpio-controller; + gpio-ranges = <&pinctrl 0 0 132>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>;
arch/arm/boot/dts/owl-s500.dtsi sps: power-controller@b01b0100 { · line 233
Quoted 10 lines
arch/arm/boot/dts/owl-s500.dtsi +7
-0+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, /* GPIOA */ + <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, /* GPIOB */ + <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>, /* GPIOC */ + <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, /* GPIOD */ + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; /* GPIOE */ + }; + dma: dma-controller@b0260000 { compatible = "actions,s500-dma"; reg = <0xb0260000 0xd00>;
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH v3 08/13] arm: dts: owl-s500: Add MMC support
In reply to Cristian CiocalteaEm 12/29/2020 6:17 PM, Cristian Ciocaltea escreveu:
Quoted 47 lines
Add MMC controller nodes for Actions Semi S500 SoC, in order to facilitate access to SD/EMMC/SDIO cards.
Signed-off-by Cristian Ciocaltea <[email protected]>Reviewed-by Ulf Hansson <[email protected]>Reviewed-by Manivannan Sadhasivam <[email protected]>---
Changes in v3:
- Added Reviewed-by tags from Ulf and Maniarch/arm/boot/dts/owl-s500.dtsi | 33 +++++++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+)arch/arm/boot/dts/owl-s500.dtsi +25
-0@@ -241,5 +241,38 @@ dma: dma-controller@b0260000 { clocks = <&cmu CLK_DMAC>; power-domains = <&sps S500_PD_DMA>; }; + + mmc0: mmc@b0230000 { + compatible = "actions,s500-mmc", "actions,owl-mmc"; + reg = <0xb0230000 0x38>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_SD0>; + resets = <&cmu RESET_SD0>; + dmas = <&dma 2>; + dma-names = "mmc"; + status = "disabled"; + }; + + mmc1: mmc@b0234000 { + compatible = "actions,s500-mmc", "actions,owl-mmc"; + reg = <0xb0234000 0x38>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_SD1>; + resets = <&cmu RESET_SD1>; + dmas = <&dma 3>; + dma-names = "mmc"; + status = "disabled"; + }; + + mmc2: mmc@b0238000 { + compatible = "actions,s500-mmc", "actions,owl-mmc";
arch/arm/boot/dts/owl-s500.dtsi dma: dma-controller@b0260000 { · line 278
Quoted 10 lines
arch/arm/boot/dts/owl-s500.dtsi +8
-0+ reg = <0xb0238000 0x38>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_SD2>; + resets = <&cmu RESET_SD2>; + dmas = <&dma 4>; + dma-names = "mmc"; + status = "disabled"; + }; }; };
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH v3 10/13] arm: dts: owl-s500: Add SIRQ controller
In reply to Cristian CiocalteaEm 12/29/2020 6:17 PM, Cristian Ciocaltea escreveu:
Quoted 23 lines
Add SIRQ controller node for Actions Semi S500 SoC.
Signed-off-by Cristian Ciocaltea <[email protected]>Reviewed-by Manivannan Sadhasivam <[email protected]>---
Changes in v3:
- Added Reviewed-by from Maniarch/arm/boot/dts/owl-s500.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+)arch/arm/boot/dts/owl-s500.dtsi +3
-0@@ -233,6 +233,16 @@ i2c3: i2c@b017c000 { status = "disabled"; }; + sirq: interrupt-controller@b01b0200 { + compatible = "actions,s500-sirq"; + reg = <0xb01b0200 0x4>;
arch/arm/boot/dts/owl-s500.dtsi i2c3: i2c@b017c000 { · line 248
Quoted 10 lines
arch/arm/boot/dts/owl-s500.dtsi +7
-0+ interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, /* SIRQ0 */ + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, /* SIRQ1 */ + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; /* SIRQ2 */ + }; + timer: timer@b0168000 { compatible = "actions,s500-timer"; reg = <0xb0168000 0x8000>;
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Re: [PATCH v3 01/13] arm: dts: owl-s500: Add Clock Management Unit
In reply to Matheus CastelloQuoted 7 lines · Matheus Castello
Em 12/29/2020 6:17 PM, Cristian Ciocaltea escreveu:
Quoted 4 lines
Add Clock Management Unit for Actions Semi S500 SoC.
Signed-off-by Cristian Ciocaltea <[email protected]>Reviewed-by Manivannan Sadhasivam <[email protected]>
[...]
Quoted 1 line
Tested-by Matheus Castello <[email protected]>
Thanks for testing this patch series!
Regards,
Cristi