Skip to contentSkip to conversation

Improve clock support for Actions S500 SoC

PATCH Superseded Cristian Ciocaltea 2 participants 13 messages May 27, 2021 – Jun 10, 2021

Subsystems (3)
Device tree bindings Common clk Arm/actions semi architecture

v2 of 3 Superseded Latest is v3 →

lore
Share & tools
lore

Cristian Ciocaltea

author
#0 lore raw

v2 cover Improve clock support for Actions S500 SoC

While working on a driver to support the Actions Semi Owl Ethernet MAC, I found and fixed some issues on the existing implementation of the S500 SoC clock subsystem and, additionally, I added two missing clocks.

Thanks,
Cristi

Changes in v2 (according to Mani's review):
- Re-added entry "{ 24, 1, 25 }" to sd_factor_table, according to the datasheet (V1.8+), this is a valid divider
- Re-added OWL_GATE_HW to SENSOR[0-1], according to the datasheet they are gated, even though the vendor implementation states the opposite
- Reverted the addition of the clock div table for H clock to support the '1' divider (according to the datasheet), even though the vendor implementation marks it as reserved
- Reordered "nic_clk_mux_p" after "ahbprediv_clk_mux_p" to follow the reg field ordering
- Rebased patch series on v5.13-rc3

Cristian Ciocaltea (6):
clk: actions: Fix UART clock dividers on Owl S500 SoC
clk: actions: Fix SD clocks factor table on Owl S500 SoC
clk: actions: Fix bisp_factor_table based clocks on Owl S500 SoC
clk: actions: Fix AHPPREDIV-H-AHB clock chain on Owl S500 SoC
dt-bindings: clock: Add NIC and ETHERNET bindings for Actions S500 SoC
clk: actions: Add NIC and ETHERNET clock support for Actions S500 SoC

 drivers/clk/actions/owl-s500.c               | 92 +++++++++++++-------
 include/dt-bindings/clock/actions,s500-cmu.h |  6 +-
 2 files changed, 65 insertions(+), 33 deletions(-)
Signature · 1 line
2.31.1
author
#1 lore raw

PATCH v2 1/6 clk: actions: Fix UART clock dividers on Owl S500 SoC

Use correct divider registers for the Actions Semi Owl S500 SoC's UART clocks.

Fixes ed6b4795ece4 ("clk: actions: Add clock driver for S500 SoC")
Signed-off-by Cristian Ciocaltea <[email protected]>
Reviewed-by Manivannan Sadhasivam <[email protected]>

---
Changes in v2:
- Added Reviewed-by from Mani

 drivers/clk/actions/owl-s500.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)
drivers/clk/actions/owl-s500.c +6 -6
index 61bb224f6330..75b7186185b0 100644
@@ -305,7 +305,7 @@ static OWL_COMP_FIXED_FACTOR(i2c3_clk, "i2c3_clk", "ethernet_pll_clk",
 static OWL_COMP_DIV(uart0_clk, "uart0_clk", uart_clk_mux_p,
 			OWL_MUX_HW(CMU_UART0CLK, 16, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN1, 6, 0),
-			OWL_DIVIDER_HW(CMU_UART1CLK, 0, 8, CLK_DIVIDER_ROUND_CLOSEST, NULL),
+			OWL_DIVIDER_HW(CMU_UART0CLK, 0, 8, CLK_DIVIDER_ROUND_CLOSEST, NULL),
 			CLK_IGNORE_UNUSED);
 
 static OWL_COMP_DIV(uart1_clk, "uart1_clk", uart_clk_mux_p,

@@ -317,31 +317,31 @@ static OWL_COMP_DIV(uart1_clk, "uart1_clk", uart_clk_mux_p,
 static OWL_COMP_DIV(uart2_clk, "uart2_clk", uart_clk_mux_p,
 			OWL_MUX_HW(CMU_UART2CLK, 16, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN1, 8, 0),
-			OWL_DIVIDER_HW(CMU_UART1CLK, 0, 8, CLK_DIVIDER_ROUND_CLOSEST, NULL),
+			OWL_DIVIDER_HW(CMU_UART2CLK, 0, 8, CLK_DIVIDER_ROUND_CLOSEST, NULL),
 			CLK_IGNORE_UNUSED);
 
 static OWL_COMP_DIV(uart3_clk, "uart3_clk", uart_clk_mux_p,
 			OWL_MUX_HW(CMU_UART3CLK, 16, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN1, 19, 0),
-			OWL_DIVIDER_HW(CMU_UART1CLK, 0, 8, CLK_DIVIDER_ROUND_CLOSEST, NULL),
+			OWL_DIVIDER_HW(CMU_UART3CLK, 0, 8, CLK_DIVIDER_ROUND_CLOSEST, NULL),
 			CLK_IGNORE_UNUSED);
 
 static OWL_COMP_DIV(uart4_clk, "uart4_clk", uart_clk_mux_p,
 			OWL_MUX_HW(CMU_UART4CLK, 16, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN1, 20, 0),
-			OWL_DIVIDER_HW(CMU_UART1CLK, 0, 8, CLK_DIVIDER_ROUND_CLOSEST, NULL),
+			OWL_DIVIDER_HW(CMU_UART4CLK, 0, 8, CLK_DIVIDER_ROUND_CLOSEST, NULL),
 			CLK_IGNORE_UNUSED);
 
 static OWL_COMP_DIV(uart5_clk, "uart5_clk", uart_clk_mux_p,
 			OWL_MUX_HW(CMU_UART5CLK, 16, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN1, 21, 0),
-			OWL_DIVIDER_HW(CMU_UART1CLK, 0, 8, CLK_DIVIDER_ROUND_CLOSEST, NULL),
+			OWL_DIVIDER_HW(CMU_UART5CLK, 0, 8, CLK_DIVIDER_ROUND_CLOSEST, NULL),
 			CLK_IGNORE_UNUSED);
 
 static OWL_COMP_DIV(uart6_clk, "uart6_clk", uart_clk_mux_p,
 			OWL_MUX_HW(CMU_UART6CLK, 16, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN1, 18, 0),
-			OWL_DIVIDER_HW(CMU_UART1CLK, 0, 8, CLK_DIVIDER_ROUND_CLOSEST, NULL),
+			OWL_DIVIDER_HW(CMU_UART6CLK, 0, 8, CLK_DIVIDER_ROUND_CLOSEST, NULL),
 			CLK_IGNORE_UNUSED);
 
 static OWL_COMP_DIV(i2srx_clk, "i2srx_clk", i2s_clk_mux_p,
Signature · 1 line
2.31.1
author
#2 lore raw

PATCH v2 2/6 clk: actions: Fix SD clocks factor table on Owl S500 SoC

In reply to Cristian Ciocaltea

Drop the unsupported entries in the factor table used for the SD[0-2] clocks definitions on the Actions Semi Owl S500 SoC.

Fixes ed6b4795ece4 ("clk: actions: Add clock driver for S500 SoC")
Signed-off-by Cristian Ciocaltea <[email protected]>

---
Changes in v2:
- Re-added entry "{ 24, 1, 25 }" to sd_factor_table, according to the datasheet (V1.8+), this is a valid divider

 drivers/clk/actions/owl-s500.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/clk/actions/owl-s500.c +2 -4
index 75b7186185b0..42abdf964044 100644
@@ -127,8 +127,7 @@ static struct clk_factor_table sd_factor_table[] = {
 	{ 12, 1, 13 }, { 13, 1, 14 }, { 14, 1, 15 }, { 15, 1, 16 },
 	{ 16, 1, 17 }, { 17, 1, 18 }, { 18, 1, 19 }, { 19, 1, 20 },
 	{ 20, 1, 21 }, { 21, 1, 22 }, { 22, 1, 23 }, { 23, 1, 24 },
-	{ 24, 1, 25 }, { 25, 1, 26 }, { 26, 1, 27 }, { 27, 1, 28 },
-	{ 28, 1, 29 }, { 29, 1, 30 }, { 30, 1, 31 }, { 31, 1, 32 },
+	{ 24, 1, 25 },
 
 	/* bit8: /128 */
 	{ 256, 1, 1 * 128 }, { 257, 1, 2 * 128 }, { 258, 1, 3 * 128 }, { 259, 1, 4 * 128 },

@@ -137,8 +136,7 @@ static struct clk_factor_table sd_factor_table[] = {
 	{ 268, 1, 13 * 128 }, { 269, 1, 14 * 128 }, { 270, 1, 15 * 128 }, { 271, 1, 16 * 128 },
 	{ 272, 1, 17 * 128 }, { 273, 1, 18 * 128 }, { 274, 1, 19 * 128 }, { 275, 1, 20 * 128 },
 	{ 276, 1, 21 * 128 }, { 277, 1, 22 * 128 }, { 278, 1, 23 * 128 }, { 279, 1, 24 * 128 },
-	{ 280, 1, 25 * 128 }, { 281, 1, 26 * 128 }, { 282, 1, 27 * 128 }, { 283, 1, 28 * 128 },
-	{ 284, 1, 29 * 128 }, { 285, 1, 30 * 128 }, { 286, 1, 31 * 128 }, { 287, 1, 32 * 128 },
+	{ 280, 1, 25 * 128 },
 	{ 0, 0, 0 },
 };
Signature · 1 line
2.31.1
Reviewed-by on v2 2/6
#3 lore raw

Re: [PATCH v2 2/6] clk: actions: Fix SD clocks factor table on Owl S500 SoC

Quoted 5 lines · Cristian Ciocaltea

Drop the unsupported entries in the factor table used for the SD[0-2] clocks definitions on the Actions Semi Owl S500 SoC.

Fixes ed6b4795ece4 ("clk: actions: Add clock driver for S500 SoC")
Signed-off-by Cristian Ciocaltea <[email protected]>
Reviewed-by Manivannan Sadhasivam <[email protected]>

Thanks,
Mani

Quoted 35 lines

---
Changes in v2:
- Re-added entry "{ 24, 1, 25 }" to sd_factor_table, according to the datasheet (V1.8+), this is a valid divider

 drivers/clk/actions/owl-s500.c | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)
drivers/clk/actions/owl-s500.c +2 -4
index 75b7186185b0..42abdf964044 100644
@@ -127,8 +127,7 @@ static struct clk_factor_table sd_factor_table[] = {
 	{ 12, 1, 13 }, { 13, 1, 14 }, { 14, 1, 15 }, { 15, 1, 16 },
 	{ 16, 1, 17 }, { 17, 1, 18 }, { 18, 1, 19 }, { 19, 1, 20 },
 	{ 20, 1, 21 }, { 21, 1, 22 }, { 22, 1, 23 }, { 23, 1, 24 },
-	{ 24, 1, 25 }, { 25, 1, 26 }, { 26, 1, 27 }, { 27, 1, 28 },
-	{ 28, 1, 29 }, { 29, 1, 30 }, { 30, 1, 31 }, { 31, 1, 32 },
+	{ 24, 1, 25 },
 
 	/* bit8: /128 */
 	{ 256, 1, 1 * 128 }, { 257, 1, 2 * 128 }, { 258, 1, 3 * 128 }, { 259, 1, 4 * 128 },

@@ -137,8 +136,7 @@ static struct clk_factor_table sd_factor_table[] = {
 	{ 268, 1, 13 * 128 }, { 269, 1, 14 * 128 }, { 270, 1, 15 * 128 }, { 271, 1, 16 * 128 },
 	{ 272, 1, 17 * 128 }, { 273, 1, 18 * 128 }, { 274, 1, 19 * 128 }, { 275, 1, 20 * 128 },
 	{ 276, 1, 21 * 128 }, { 277, 1, 22 * 128 }, { 278, 1, 23 * 128 }, { 279, 1, 24 * 128 },
-	{ 280, 1, 25 * 128 }, { 281, 1, 26 * 128 }, { 282, 1, 27 * 128 }, { 283, 1, 28 * 128 },
-	{ 284, 1, 29 * 128 }, { 285, 1, 30 * 128 }, { 286, 1, 31 * 128 }, { 287, 1, 32 * 128 },
+	{ 280, 1, 25 * 128 },
 	{ 0, 0, 0 },
 };
Signature · 1 line
2.31.1
author
#4 lore raw

PATCH v2 3/6 clk: actions: Fix bisp_factor_table based clocks on Owl S500 SoC

In reply to Cristian Ciocaltea

The following clocks of the Actions Semi Owl S500 SoC have been defined to use a shared clock factor table 'bisp_factor_table[]': DE[1-2], VCE, VDE, BISP, SENSOR[0-1]

There are several issues involved in this approach:

* 'bisp_factor_table[]' describes the configuration of a regular 8-rates divider, so its usage is redundant. Additionally, judging by the BISP clock context, it is incomplete since it maps only 8 out of 12 possible entries.

* The clocks mentioned above are not identical in terms of the available rates, therefore cannot rely on the same factor table. Specifically, BISP and SENSOR* are standard 12-rate dividers so their configuration should rely on a proper clock div table, while VCE and VDE require a factor table that is a actually a subset of the one needed for DE[1-2] clocks.

Let's fix this by implementing the following:

* Add new factor tables 'de_factor_table' and 'hde_factor_table' to properly handle DE[1-2], VCE and VDE clocks.

* Add a common div table 'std12rate_div_table' for BISP and SENSOR[0-1] clocks converted to OWL_COMP_DIV.

* Drop the now unused 'bisp_factor_table[]'.

Additionally, drop the CLK_IGNORE_UNUSED flag for SENSOR[0-1] since there is no reason to always keep ON those clocks.

Fixes ed6b4795ece4 ("clk: actions: Add clock driver for S500 SoC")
Signed-off-by Cristian Ciocaltea <[email protected]>

---
Changes in v2:
- Re-added OWL_GATE_HW to SENSOR[0-1], according to the datasheet they are gated, even though the vendor implementation states the opposite

 drivers/clk/actions/owl-s500.c | 44 ++++++++++++++++++++++------------
 1 file changed, 29 insertions(+), 15 deletions(-)
drivers/clk/actions/owl-s500.c +29 -15
index 42abdf964044..42d6899755e6 100644
@@ -140,9 +140,16 @@ static struct clk_factor_table sd_factor_table[] = {
 	{ 0, 0, 0 },
 };
 
-static struct clk_factor_table bisp_factor_table[] = {
-	{ 0, 1, 1 }, { 1, 1, 2 }, { 2, 1, 3 }, { 3, 1, 4 },
-	{ 4, 1, 5 }, { 5, 1, 6 }, { 6, 1, 7 }, { 7, 1, 8 },
+static struct clk_factor_table de_factor_table[] = {
+	{ 0, 1, 1 }, { 1, 2, 3 }, { 2, 1, 2 }, { 3, 2, 5 },
+	{ 4, 1, 3 }, { 5, 1, 4 }, { 6, 1, 6 }, { 7, 1, 8 },
+	{ 8, 1, 12 },
+	{ 0, 0, 0 },
+};
+
+static struct clk_factor_table hde_factor_table[] = {
+	{ 0, 1, 1 }, { 1, 2, 3 }, { 2, 1, 2 }, { 3, 2, 5 },
+	{ 4, 1, 3 }, { 5, 1, 4 }, { 6, 1, 6 }, { 7, 1, 8 },
 	{ 0, 0, 0 },
 };
 

@@ -156,6 +163,13 @@ static struct clk_div_table rmii_ref_div_table[] = {
 	{ 0, 0 },
 };
 
+static struct clk_div_table std12rate_div_table[] = {
+	{ 0, 1 }, { 1, 2 }, { 2, 3 }, { 3, 4 },
+	{ 4, 5 }, { 5, 6 }, { 6, 7 }, { 7, 8 },
+	{ 8, 9 }, { 9, 10 }, { 10, 11 }, { 11, 12 },
+	{ 0, 0 },
+};
+
 static struct clk_div_table i2s_div_table[] = {
 	{ 0, 1 }, { 1, 2 }, { 2, 3 }, { 3, 4 },
 	{ 4, 6 }, { 5, 8 }, { 6, 12 }, { 7, 16 },

@@ -191,39 +205,39 @@ static OWL_DIVIDER(rmii_ref_clk, "rmii_ref_clk", "ethernet_pll_clk", CMU_ETHERNE
 
 /* factor clocks */
 static OWL_FACTOR(ahb_clk, "ahb_clk", "h_clk", CMU_BUSCLK1, 2, 2, ahb_factor_table, 0, 0);
-static OWL_FACTOR(de1_clk, "de_clk1", "de_clk", CMU_DECLK, 0, 3, bisp_factor_table, 0, 0);
-static OWL_FACTOR(de2_clk, "de_clk2", "de_clk", CMU_DECLK, 4, 3, bisp_factor_table, 0, 0);
+static OWL_FACTOR(de1_clk, "de_clk1", "de_clk", CMU_DECLK, 0, 4, de_factor_table, 0, 0);
+static OWL_FACTOR(de2_clk, "de_clk2", "de_clk", CMU_DECLK, 4, 4, de_factor_table, 0, 0);
 
 /* composite clocks */
 static OWL_COMP_FACTOR(vce_clk, "vce_clk", hde_clk_mux_p,
 			OWL_MUX_HW(CMU_VCECLK, 4, 2),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 26, 0),
-			OWL_FACTOR_HW(CMU_VCECLK, 0, 3, 0, bisp_factor_table),
+			OWL_FACTOR_HW(CMU_VCECLK, 0, 3, 0, hde_factor_table),
 			0);
 
 static OWL_COMP_FACTOR(vde_clk, "vde_clk", hde_clk_mux_p,
 			OWL_MUX_HW(CMU_VDECLK, 4, 2),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 25, 0),
-			OWL_FACTOR_HW(CMU_VDECLK, 0, 3, 0, bisp_factor_table),
+			OWL_FACTOR_HW(CMU_VDECLK, 0, 3, 0, hde_factor_table),
 			0);
 
-static OWL_COMP_FACTOR(bisp_clk, "bisp_clk", bisp_clk_mux_p,
+static OWL_COMP_DIV(bisp_clk, "bisp_clk", bisp_clk_mux_p,
 			OWL_MUX_HW(CMU_BISPCLK, 4, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 14, 0),
-			OWL_FACTOR_HW(CMU_BISPCLK, 0, 3, 0, bisp_factor_table),
+			OWL_DIVIDER_HW(CMU_BISPCLK, 0, 4, 0, std12rate_div_table),
 			0);
 
-static OWL_COMP_FACTOR(sensor0_clk, "sensor0_clk", sensor_clk_mux_p,
+static OWL_COMP_DIV(sensor0_clk, "sensor0_clk", sensor_clk_mux_p,
 			OWL_MUX_HW(CMU_SENSORCLK, 4, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 14, 0),
-			OWL_FACTOR_HW(CMU_SENSORCLK, 0, 3, 0, bisp_factor_table),
-			CLK_IGNORE_UNUSED);
+			OWL_DIVIDER_HW(CMU_SENSORCLK, 0, 4, 0, std12rate_div_table),
+			0);
 
-static OWL_COMP_FACTOR(sensor1_clk, "sensor1_clk", sensor_clk_mux_p,
+static OWL_COMP_DIV(sensor1_clk, "sensor1_clk", sensor_clk_mux_p,
 			OWL_MUX_HW(CMU_SENSORCLK, 4, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 14, 0),
-			OWL_FACTOR_HW(CMU_SENSORCLK, 8, 3, 0, bisp_factor_table),
-			CLK_IGNORE_UNUSED);
+			OWL_DIVIDER_HW(CMU_SENSORCLK, 8, 4, 0, std12rate_div_table),
+			0);
 
 static OWL_COMP_FACTOR(sd0_clk, "sd0_clk", sd_clk_mux_p,
 			OWL_MUX_HW(CMU_SD0CLK, 9, 1),
Signature · 1 line
2.31.1
Reviewed-by on v2 3/6
#5 lore raw

Re: [PATCH v2 3/6] clk: actions: Fix bisp_factor_table based clocks on Owl S500 SoC

Quoted 26 lines · Cristian Ciocaltea

The following clocks of the Actions Semi Owl S500 SoC have been defined to use a shared clock factor table 'bisp_factor_table[]': DE[1-2], VCE, VDE, BISP, SENSOR[0-1]

There are several issues involved in this approach:

* 'bisp_factor_table[]' describes the configuration of a regular 8-rates divider, so its usage is redundant. Additionally, judging by the BISP clock context, it is incomplete since it maps only 8 out of 12 possible entries.

* The clocks mentioned above are not identical in terms of the available rates, therefore cannot rely on the same factor table. Specifically, BISP and SENSOR* are standard 12-rate dividers so their configuration should rely on a proper clock div table, while VCE and VDE require a factor table that is a actually a subset of the one needed for DE[1-2] clocks.

Let's fix this by implementing the following:

* Add new factor tables 'de_factor_table' and 'hde_factor_table' to properly handle DE[1-2], VCE and VDE clocks.

* Add a common div table 'std12rate_div_table' for BISP and SENSOR[0-1] clocks converted to OWL_COMP_DIV.

Quoted 7 lines

* Drop the now unused 'bisp_factor_table[]'.

Additionally, drop the CLK_IGNORE_UNUSED flag for SENSOR[0-1] since there is no reason to always keep ON those clocks.

Fixes ed6b4795ece4 ("clk: actions: Add clock driver for S500 SoC")
Signed-off-by Cristian Ciocaltea <[email protected]>
Reviewed-by Manivannan Sadhasivam <[email protected]>

Thanks,
Mani

Quoted 101 lines

---
Changes in v2:
- Re-added OWL_GATE_HW to SENSOR[0-1], according to the datasheet they are gated, even though the vendor implementation states the opposite

 drivers/clk/actions/owl-s500.c | 44 ++++++++++++++++++++++------------
 1 file changed, 29 insertions(+), 15 deletions(-)
drivers/clk/actions/owl-s500.c +29 -15
index 42abdf964044..42d6899755e6 100644
@@ -140,9 +140,16 @@ static struct clk_factor_table sd_factor_table[] = {
 	{ 0, 0, 0 },
 };
 
-static struct clk_factor_table bisp_factor_table[] = {
-	{ 0, 1, 1 }, { 1, 1, 2 }, { 2, 1, 3 }, { 3, 1, 4 },
-	{ 4, 1, 5 }, { 5, 1, 6 }, { 6, 1, 7 }, { 7, 1, 8 },
+static struct clk_factor_table de_factor_table[] = {
+	{ 0, 1, 1 }, { 1, 2, 3 }, { 2, 1, 2 }, { 3, 2, 5 },
+	{ 4, 1, 3 }, { 5, 1, 4 }, { 6, 1, 6 }, { 7, 1, 8 },
+	{ 8, 1, 12 },
+	{ 0, 0, 0 },
+};
+
+static struct clk_factor_table hde_factor_table[] = {
+	{ 0, 1, 1 }, { 1, 2, 3 }, { 2, 1, 2 }, { 3, 2, 5 },
+	{ 4, 1, 3 }, { 5, 1, 4 }, { 6, 1, 6 }, { 7, 1, 8 },
 	{ 0, 0, 0 },
 };
 

@@ -156,6 +163,13 @@ static struct clk_div_table rmii_ref_div_table[] = {
 	{ 0, 0 },
 };
 
+static struct clk_div_table std12rate_div_table[] = {
+	{ 0, 1 }, { 1, 2 }, { 2, 3 }, { 3, 4 },
+	{ 4, 5 }, { 5, 6 }, { 6, 7 }, { 7, 8 },
+	{ 8, 9 }, { 9, 10 }, { 10, 11 }, { 11, 12 },
+	{ 0, 0 },
+};
+
 static struct clk_div_table i2s_div_table[] = {
 	{ 0, 1 }, { 1, 2 }, { 2, 3 }, { 3, 4 },
 	{ 4, 6 }, { 5, 8 }, { 6, 12 }, { 7, 16 },

@@ -191,39 +205,39 @@ static OWL_DIVIDER(rmii_ref_clk, "rmii_ref_clk", "ethernet_pll_clk", CMU_ETHERNE
 
 /* factor clocks */
 static OWL_FACTOR(ahb_clk, "ahb_clk", "h_clk", CMU_BUSCLK1, 2, 2, ahb_factor_table, 0, 0);
-static OWL_FACTOR(de1_clk, "de_clk1", "de_clk", CMU_DECLK, 0, 3, bisp_factor_table, 0, 0);
-static OWL_FACTOR(de2_clk, "de_clk2", "de_clk", CMU_DECLK, 4, 3, bisp_factor_table, 0, 0);
+static OWL_FACTOR(de1_clk, "de_clk1", "de_clk", CMU_DECLK, 0, 4, de_factor_table, 0, 0);
+static OWL_FACTOR(de2_clk, "de_clk2", "de_clk", CMU_DECLK, 4, 4, de_factor_table, 0, 0);
 
 /* composite clocks */
 static OWL_COMP_FACTOR(vce_clk, "vce_clk", hde_clk_mux_p,
 			OWL_MUX_HW(CMU_VCECLK, 4, 2),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 26, 0),
-			OWL_FACTOR_HW(CMU_VCECLK, 0, 3, 0, bisp_factor_table),
+			OWL_FACTOR_HW(CMU_VCECLK, 0, 3, 0, hde_factor_table),
 			0);
 
 static OWL_COMP_FACTOR(vde_clk, "vde_clk", hde_clk_mux_p,
 			OWL_MUX_HW(CMU_VDECLK, 4, 2),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 25, 0),
-			OWL_FACTOR_HW(CMU_VDECLK, 0, 3, 0, bisp_factor_table),
+			OWL_FACTOR_HW(CMU_VDECLK, 0, 3, 0, hde_factor_table),
 			0);
 
-static OWL_COMP_FACTOR(bisp_clk, "bisp_clk", bisp_clk_mux_p,
+static OWL_COMP_DIV(bisp_clk, "bisp_clk", bisp_clk_mux_p,
 			OWL_MUX_HW(CMU_BISPCLK, 4, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 14, 0),
-			OWL_FACTOR_HW(CMU_BISPCLK, 0, 3, 0, bisp_factor_table),
+			OWL_DIVIDER_HW(CMU_BISPCLK, 0, 4, 0, std12rate_div_table),
 			0);
 
-static OWL_COMP_FACTOR(sensor0_clk, "sensor0_clk", sensor_clk_mux_p,
+static OWL_COMP_DIV(sensor0_clk, "sensor0_clk", sensor_clk_mux_p,
 			OWL_MUX_HW(CMU_SENSORCLK, 4, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 14, 0),
-			OWL_FACTOR_HW(CMU_SENSORCLK, 0, 3, 0, bisp_factor_table),
-			CLK_IGNORE_UNUSED);
+			OWL_DIVIDER_HW(CMU_SENSORCLK, 0, 4, 0, std12rate_div_table),
+			0);
 
-static OWL_COMP_FACTOR(sensor1_clk, "sensor1_clk", sensor_clk_mux_p,
+static OWL_COMP_DIV(sensor1_clk, "sensor1_clk", sensor_clk_mux_p,
 			OWL_MUX_HW(CMU_SENSORCLK, 4, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 14, 0),
-			OWL_FACTOR_HW(CMU_SENSORCLK, 8, 3, 0, bisp_factor_table),
-			CLK_IGNORE_UNUSED);
+			OWL_DIVIDER_HW(CMU_SENSORCLK, 8, 4, 0, std12rate_div_table),
+			0);
 
 static OWL_COMP_FACTOR(sd0_clk, "sd0_clk", sd_clk_mux_p,
 			OWL_MUX_HW(CMU_SD0CLK, 9, 1),
Signature · 1 line
2.31.1
author
#6 lore raw

PATCH v2 4/6 clk: actions: Fix AHPPREDIV-H-AHB clock chain on Owl S500 SoC

In reply to Cristian Ciocaltea

There are a few issues with the setup of the Actions Semi Owl S500 SoC's clock chain involving AHPPREDIV, H and AHB clocks:

* AHBPREDIV clock is defined as a muxer only, although it also acts as a divider.
* H clock is using a wrong divider register offset
* AHB is defined as a multi-rate factor clock, but it is actually just a fixed pass clock.

Let's provide the following fixes:

* Change AHBPREDIV clock to an ungated OWL_COMP_DIV definition.
* Use the correct register shift value in the OWL_DIVIDER definition for H clock
* Drop the unneeded 'ahb_factor_table[]' and change AHB clock to an ungated OWL_COMP_FIXED_FACTOR definition.

Fixes ed6b4795ece4 ("clk: actions: Add clock driver for S500 SoC")
Signed-off-by Cristian Ciocaltea <[email protected]>

---
Changes in v2:
- Reverted the addition of the clock div table for H clock to support the '1' divider (according to the datasheet), even though the vendor implementation marks it as reserved

 drivers/clk/actions/owl-s500.c | 19 +++++++++++--------
 1 file changed, 11 insertions(+), 8 deletions(-)
drivers/clk/actions/owl-s500.c +11 -8
index 42d6899755e6..257923bd5386 100644
@@ -153,11 +153,6 @@ static struct clk_factor_table hde_factor_table[] = {
 	{ 0, 0, 0 },
 };
 
-static struct clk_factor_table ahb_factor_table[] = {
-	{ 1, 1, 2 }, { 2, 1, 3 },
-	{ 0, 0, 0 },
-};
-
 static struct clk_div_table rmii_ref_div_table[] = {
 	{ 0, 4 }, { 1, 10 },
 	{ 0, 0 },

@@ -186,7 +181,6 @@ static struct clk_div_table nand_div_table[] = {
 
 /* mux clock */
 static OWL_MUX(dev_clk, "dev_clk", dev_clk_mux_p, CMU_DEVPLL, 12, 1, CLK_SET_RATE_PARENT);
-static OWL_MUX(ahbprediv_clk, "ahbprediv_clk", ahbprediv_clk_mux_p, CMU_BUSCLK1, 8, 3, CLK_SET_RATE_PARENT);
 
 /* gate clocks */
 static OWL_GATE(gpio_clk, "gpio_clk", "apb_clk", CMU_DEVCLKEN0, 18, 0, 0);

@@ -199,16 +193,25 @@ static OWL_GATE(timer_clk, "timer_clk", "hosc", CMU_DEVCLKEN1, 27, 0, 0);
 static OWL_GATE(hdmi_clk, "hdmi_clk", "hosc", CMU_DEVCLKEN1, 3, 0, 0);
 
 /* divider clocks */
-static OWL_DIVIDER(h_clk, "h_clk", "ahbprediv_clk", CMU_BUSCLK1, 12, 2, NULL, 0, 0);
+static OWL_DIVIDER(h_clk, "h_clk", "ahbprediv_clk", CMU_BUSCLK1, 2, 2, NULL, 0, 0);
 static OWL_DIVIDER(apb_clk, "apb_clk", "ahb_clk", CMU_BUSCLK1, 14, 2, NULL, 0, 0);
 static OWL_DIVIDER(rmii_ref_clk, "rmii_ref_clk", "ethernet_pll_clk", CMU_ETHERNETPLL, 1, 1, rmii_ref_div_table, 0, 0);
 
 /* factor clocks */
-static OWL_FACTOR(ahb_clk, "ahb_clk", "h_clk", CMU_BUSCLK1, 2, 2, ahb_factor_table, 0, 0);
 static OWL_FACTOR(de1_clk, "de_clk1", "de_clk", CMU_DECLK, 0, 4, de_factor_table, 0, 0);
 static OWL_FACTOR(de2_clk, "de_clk2", "de_clk", CMU_DECLK, 4, 4, de_factor_table, 0, 0);
 
 /* composite clocks */
+static OWL_COMP_DIV(ahbprediv_clk, "ahbprediv_clk", ahbprediv_clk_mux_p,
+			OWL_MUX_HW(CMU_BUSCLK1, 8, 3),
+			{ 0 },
+			OWL_DIVIDER_HW(CMU_BUSCLK1, 12, 2, 0, NULL),
+			0);
+
+static OWL_COMP_FIXED_FACTOR(ahb_clk, "ahb_clk", "h_clk",
+			{ 0 },
+			1, 1, CLK_SET_RATE_PARENT);
+
 static OWL_COMP_FACTOR(vce_clk, "vce_clk", hde_clk_mux_p,
 			OWL_MUX_HW(CMU_VCECLK, 4, 2),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 26, 0),
Signature · 1 line
2.31.1
#7 lore raw

Re: [PATCH v2 4/6] clk: actions: Fix AHPPREDIV-H-AHB clock chain on Owl S500 SoC

Quoted 66 lines · Cristian Ciocaltea

There are a few issues with the setup of the Actions Semi Owl S500 SoC's clock chain involving AHPPREDIV, H and AHB clocks:

* AHBPREDIV clock is defined as a muxer only, although it also acts as a divider.
* H clock is using a wrong divider register offset
* AHB is defined as a multi-rate factor clock, but it is actually just a fixed pass clock.

Let's provide the following fixes:

* Change AHBPREDIV clock to an ungated OWL_COMP_DIV definition.
* Use the correct register shift value in the OWL_DIVIDER definition for H clock
* Drop the unneeded 'ahb_factor_table[]' and change AHB clock to an ungated OWL_COMP_FIXED_FACTOR definition.

Fixes ed6b4795ece4 ("clk: actions: Add clock driver for S500 SoC")
Signed-off-by Cristian Ciocaltea <[email protected]>

---
Changes in v2:
- Reverted the addition of the clock div table for H clock to support the '1' divider (according to the datasheet), even though the vendor implementation marks it as reserved

 drivers/clk/actions/owl-s500.c | 19 +++++++++++--------
 1 file changed, 11 insertions(+), 8 deletions(-)
drivers/clk/actions/owl-s500.c +1 -8
index 42d6899755e6..257923bd5386 100644
@@ -153,11 +153,6 @@ static struct clk_factor_table hde_factor_table[] = {
 	{ 0, 0, 0 },
 };
 
-static struct clk_factor_table ahb_factor_table[] = {
-	{ 1, 1, 2 }, { 2, 1, 3 },
-	{ 0, 0, 0 },
-};
-
 static struct clk_div_table rmii_ref_div_table[] = {
 	{ 0, 4 }, { 1, 10 },
 	{ 0, 0 },

@@ -186,7 +181,6 @@ static struct clk_div_table nand_div_table[] = {
 
 /* mux clock */
 static OWL_MUX(dev_clk, "dev_clk", dev_clk_mux_p, CMU_DEVPLL, 12, 1, CLK_SET_RATE_PARENT);
-static OWL_MUX(ahbprediv_clk, "ahbprediv_clk", ahbprediv_clk_mux_p, CMU_BUSCLK1, 8, 3, CLK_SET_RATE_PARENT);
 
 /* gate clocks */
 static OWL_GATE(gpio_clk, "gpio_clk", "apb_clk", CMU_DEVCLKEN0, 18, 0, 0);

@@ -199,16 +193,25 @@ static OWL_GATE(timer_clk, "timer_clk", "hosc", CMU_DEVCLKEN1, 27, 0, 0);
 static OWL_GATE(hdmi_clk, "hdmi_clk", "hosc", CMU_DEVCLKEN1, 3, 0, 0);
 
 /* divider clocks */
-static OWL_DIVIDER(h_clk, "h_clk", "ahbprediv_clk", CMU_BUSCLK1, 12, 2, NULL, 0, 0);
+static OWL_DIVIDER(h_clk, "h_clk", "ahbprediv_clk", CMU_BUSCLK1, 2, 2, NULL, 0, 0);
 static OWL_DIVIDER(apb_clk, "apb_clk", "ahb_clk", CMU_BUSCLK1, 14, 2, NULL, 0, 0);
 static OWL_DIVIDER(rmii_ref_clk, "rmii_ref_clk", "ethernet_pll_clk", CMU_ETHERNETPLL, 1, 1, rmii_ref_div_table, 0, 0);
 
 /* factor clocks */
-static OWL_FACTOR(ahb_clk, "ahb_clk", "h_clk", CMU_BUSCLK1, 2, 2, ahb_factor_table, 0, 0);
 static OWL_FACTOR(de1_clk, "de_clk1", "de_clk", CMU_DECLK, 0, 4, de_factor_table, 0, 0);
 static OWL_FACTOR(de2_clk, "de_clk2", "de_clk", CMU_DECLK, 4, 4, de_factor_table, 0, 0);

drivers/clk/actions/owl-s500.c static OWL_GATE(timer_clk, "timer_clk", "hosc", CMU_DEVCLKEN1, 27, 0, 0); · line 213

Quoted 10 lines
drivers/clk/actions/owl-s500.c +9 -0
 /* composite clocks */
+static OWL_COMP_DIV(ahbprediv_clk, "ahbprediv_clk", ahbprediv_clk_mux_p,
+			OWL_MUX_HW(CMU_BUSCLK1, 8, 3),
+			{ 0 },
+			OWL_DIVIDER_HW(CMU_BUSCLK1, 12, 2, 0, NULL),
+			0);
+
+static OWL_COMP_FIXED_FACTOR(ahb_clk, "ahb_clk", "h_clk",
+			{ 0 },
+			1, 1, CLK_SET_RATE_PARENT);

I think you swapped the flags between "ahbprediv_clk" and "ahb_clk"...

Quoted 7 lines
drivers/clk/actions/owl-s500.c +1 -0
+
 static OWL_COMP_FACTOR(vce_clk, "vce_clk", hde_clk_mux_p,
 			OWL_MUX_HW(CMU_VCECLK, 4, 2),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 26, 0),
Signature · 1 line
2.31.1
author
#8 lore raw

Re: [PATCH v2 4/6] clk: actions: Fix AHPPREDIV-H-AHB clock chain on Owl S500 SoC

Quoted 17 lines · Manivannan Sadhasivam
Quoted 16 lines · Cristian Ciocaltea

There are a few issues with the setup of the Actions Semi Owl S500 SoC's clock chain involving AHPPREDIV, H and AHB clocks:

* AHBPREDIV clock is defined as a muxer only, although it also acts as a divider.
* H clock is using a wrong divider register offset
* AHB is defined as a multi-rate factor clock, but it is actually just a fixed pass clock.

Let's provide the following fixes:

* Change AHBPREDIV clock to an ungated OWL_COMP_DIV definition.
* Use the correct register shift value in the OWL_DIVIDER definition for H clock
* Drop the unneeded 'ahb_factor_table[]' and change AHB clock to an ungated OWL_COMP_FIXED_FACTOR definition.

[...]

Quoted 4 lines
Quoted 4 lines

/* composite clocks */

drivers/clk/actions/owl-s500.c +3 -0
+static OWL_COMP_DIV(ahbprediv_clk, "ahbprediv_clk", ahbprediv_clk_mux_p,
+			OWL_MUX_HW(CMU_BUSCLK1, 8, 3),
+			{ 0 },
Quoted 8 lines

drivers/clk/actions/owl-s500.c static OWL_GATE(timer_clk, "timer_clk", "hosc", CMU_DEVCLKEN1, 27, 0, 0); · line 213

Quoted 6 lines
drivers/clk/actions/owl-s500.c +6 -0
+			OWL_DIVIDER_HW(CMU_BUSCLK1, 12, 2, 0, NULL),
+			0);
+
+static OWL_COMP_FIXED_FACTOR(ahb_clk, "ahb_clk", "h_clk",
+			{ 0 },
+			1, 1, CLK_SET_RATE_PARENT);

I think you swapped the flags between "ahbprediv_clk" and "ahb_clk"...

Thanks for noticing this, I fixed it in v3:
https://lore.kernel.org/lkml/[email protected]/

Quoted 7 lines
Quoted 7 lines
drivers/clk/actions/owl-s500.c +1 -0
+
 static OWL_COMP_FACTOR(vce_clk, "vce_clk", hde_clk_mux_p,
 			OWL_MUX_HW(CMU_VCECLK, 4, 2),
 			OWL_GATE_HW(CMU_DEVCLKEN0, 26, 0),
Signature · 1 line
2.31.1
author
#9 lore raw

PATCH v2 5/6 dt-bindings: clock: Add NIC and ETHERNET bindings for Actions S500 SoC

In reply to Cristian Ciocaltea

Add the missing NIC and ETHERNET clock bindings constants for Actions Semi Owl S500 SoC.

Signed-off-by Cristian Ciocaltea <[email protected]>
Acked-by Rob Herring <[email protected]>

---
Changes in v2:
- Added Acked-by from Rob

 include/dt-bindings/clock/actions,s500-cmu.h | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
include/dt-bindings/clock/actions,s500-cmu.h +4 -2
index a250a52a6192..a237eb26accb 100644
@@ -74,10 +74,12 @@
 #define CLK_RMII_REF		54
 #define CLK_GPIO		55
 
-/* system clock (part 2) */
+/* additional clocks */
 #define CLK_APB			56
 #define CLK_DMAC		57
+#define CLK_NIC			58
+#define CLK_ETHERNET		59
 
-#define CLK_NR_CLKS		(CLK_DMAC + 1)
+#define CLK_NR_CLKS		(CLK_ETHERNET + 1)
 
 #endif /* __DT_BINDINGS_CLOCK_S500_CMU_H */
Signature · 1 line
2.31.1
Reviewed-by on v2 5/6
#10 lore raw

Re: [PATCH v2 5/6] dt-bindings: clock: Add NIC and ETHERNET bindings for Actions S500 SoC

Quoted 5 lines · Cristian Ciocaltea

Add the missing NIC and ETHERNET clock bindings constants for Actions Semi Owl S500 SoC.

Signed-off-by Cristian Ciocaltea <[email protected]>
Acked-by Rob Herring <[email protected]>
Reviewed-by Manivannan Sadhasivam <[email protected]>

Thanks,
Mani

Quoted 29 lines

---
Changes in v2:
- Added Acked-by from Rob

 include/dt-bindings/clock/actions,s500-cmu.h | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)
include/dt-bindings/clock/actions,s500-cmu.h +4 -2
index a250a52a6192..a237eb26accb 100644
@@ -74,10 +74,12 @@
 #define CLK_RMII_REF		54
 #define CLK_GPIO		55
 
-/* system clock (part 2) */
+/* additional clocks */
 #define CLK_APB			56
 #define CLK_DMAC		57
+#define CLK_NIC			58
+#define CLK_ETHERNET		59
 
-#define CLK_NR_CLKS		(CLK_DMAC + 1)
+#define CLK_NR_CLKS		(CLK_ETHERNET + 1)
 
 #endif /* __DT_BINDINGS_CLOCK_S500_CMU_H */
Signature · 1 line
2.31.1
author
#11 lore raw

PATCH v2 6/6 clk: actions: Add NIC and ETHERNET clock support for Actions S500 SoC

In reply to Cristian Ciocaltea

Add support for the missing NIC and ETHERNET clocks in the Actions Semi Owl S500 SoC clock driver.

Additionally, change APB clock parent from AHB to the newly added NIC.

Signed-off-by Cristian Ciocaltea <[email protected]>

---
Changes in v2:
- Reordered "nic_clk_mux_p" after "ahbprediv_clk_mux_p" to follow the reg field ordering

 drivers/clk/actions/owl-s500.c | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)
drivers/clk/actions/owl-s500.c +16 -1
index 257923bd5386..a9c7e06ebcd6 100644
@@ -113,6 +113,7 @@ static const char * const sensor_clk_mux_p[] = { "hosc", "bisp_clk" };
 static const char * const sd_clk_mux_p[] = { "dev_clk", "nand_pll_clk" };
 static const char * const pwm_clk_mux_p[] = { "losc", "hosc" };
 static const char * const ahbprediv_clk_mux_p[] = { "dev_clk", "display_pll_clk", "nand_pll_clk", "ddr_pll_clk" };
+static const char * const nic_clk_mux_p[] = { "dev_clk", "display_pll_clk", "nand_pll_clk", "ddr_pll_clk" };
 static const char * const uart_clk_mux_p[] = { "hosc", "dev_pll_clk" };
 static const char * const de_clk_mux_p[] = { "display_pll_clk", "dev_clk" };
 static const char * const i2s_clk_mux_p[] = { "audio_pll_clk" };

@@ -194,7 +195,7 @@ static OWL_GATE(hdmi_clk, "hdmi_clk", "hosc", CMU_DEVCLKEN1, 3, 0, 0);
 
 /* divider clocks */
 static OWL_DIVIDER(h_clk, "h_clk", "ahbprediv_clk", CMU_BUSCLK1, 2, 2, NULL, 0, 0);
-static OWL_DIVIDER(apb_clk, "apb_clk", "ahb_clk", CMU_BUSCLK1, 14, 2, NULL, 0, 0);
+static OWL_DIVIDER(apb_clk, "apb_clk", "nic_clk", CMU_BUSCLK1, 14, 2, NULL, 0, 0);
 static OWL_DIVIDER(rmii_ref_clk, "rmii_ref_clk", "ethernet_pll_clk", CMU_ETHERNETPLL, 1, 1, rmii_ref_div_table, 0, 0);
 
 /* factor clocks */

@@ -202,6 +203,12 @@ static OWL_FACTOR(de1_clk, "de_clk1", "de_clk", CMU_DECLK, 0, 4, de_factor_table
 static OWL_FACTOR(de2_clk, "de_clk2", "de_clk", CMU_DECLK, 4, 4, de_factor_table, 0, 0);
 
 /* composite clocks */
+static OWL_COMP_DIV(nic_clk, "nic_clk", nic_clk_mux_p,
+			OWL_MUX_HW(CMU_BUSCLK1, 4, 3),
+			{ 0 },
+			OWL_DIVIDER_HW(CMU_BUSCLK1, 16, 2, 0, NULL),
+			0);
+
 static OWL_COMP_DIV(ahbprediv_clk, "ahbprediv_clk", ahbprediv_clk_mux_p,
 			OWL_MUX_HW(CMU_BUSCLK1, 8, 3),
 			{ 0 },

@@ -317,6 +324,10 @@ static OWL_COMP_FIXED_FACTOR(i2c3_clk, "i2c3_clk", "ethernet_pll_clk",
 			OWL_GATE_HW(CMU_DEVCLKEN1, 31, 0),
 			1, 5, 0);
 
+static OWL_COMP_FIXED_FACTOR(ethernet_clk, "ethernet_clk", "ethernet_pll_clk",
+			OWL_GATE_HW(CMU_DEVCLKEN1, 22, 0),
+			1, 20, 0);
+
 static OWL_COMP_DIV(uart0_clk, "uart0_clk", uart_clk_mux_p,
 			OWL_MUX_HW(CMU_UART0CLK, 16, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN1, 6, 0),

@@ -451,6 +462,8 @@ static struct owl_clk_common *s500_clks[] = {
 	&apb_clk.common,
 	&dmac_clk.common,
 	&gpio_clk.common,
+	&nic_clk.common,
+	&ethernet_clk.common,
 };
 
 static struct clk_hw_onecell_data s500_hw_clks = {

@@ -510,6 +523,8 @@ static struct clk_hw_onecell_data s500_hw_clks = {
 		[CLK_APB]		= &apb_clk.common.hw,
 		[CLK_DMAC]		= &dmac_clk.common.hw,
 		[CLK_GPIO]		= &gpio_clk.common.hw,
+		[CLK_NIC]		= &nic_clk.common.hw,
+		[CLK_ETHERNET]		= &ethernet_clk.common.hw,
 	},
 	.num = CLK_NR_CLKS,
 };
Signature · 1 line
2.31.1
Reviewed-by on v2 6/6
#12 lore raw

Re: [PATCH v2 6/6] clk: actions: Add NIC and ETHERNET clock support for Actions S500 SoC

Quoted 6 lines · Cristian Ciocaltea

Add support for the missing NIC and ETHERNET clocks in the Actions Semi Owl S500 SoC clock driver.

Additionally, change APB clock parent from AHB to the newly added NIC.

Signed-off-by Cristian Ciocaltea <[email protected]>
Reviewed-by Manivannan Sadhasivam <[email protected]>

Thanks,
Mani

Quoted 74 lines

---
Changes in v2:
- Reordered "nic_clk_mux_p" after "ahbprediv_clk_mux_p" to follow the reg field ordering

 drivers/clk/actions/owl-s500.c | 17 ++++++++++++++++-
 1 file changed, 16 insertions(+), 1 deletion(-)
drivers/clk/actions/owl-s500.c +16 -1
index 257923bd5386..a9c7e06ebcd6 100644
@@ -113,6 +113,7 @@ static const char * const sensor_clk_mux_p[] = { "hosc", "bisp_clk" };
 static const char * const sd_clk_mux_p[] = { "dev_clk", "nand_pll_clk" };
 static const char * const pwm_clk_mux_p[] = { "losc", "hosc" };
 static const char * const ahbprediv_clk_mux_p[] = { "dev_clk", "display_pll_clk", "nand_pll_clk", "ddr_pll_clk" };
+static const char * const nic_clk_mux_p[] = { "dev_clk", "display_pll_clk", "nand_pll_clk", "ddr_pll_clk" };
 static const char * const uart_clk_mux_p[] = { "hosc", "dev_pll_clk" };
 static const char * const de_clk_mux_p[] = { "display_pll_clk", "dev_clk" };
 static const char * const i2s_clk_mux_p[] = { "audio_pll_clk" };

@@ -194,7 +195,7 @@ static OWL_GATE(hdmi_clk, "hdmi_clk", "hosc", CMU_DEVCLKEN1, 3, 0, 0);
 
 /* divider clocks */
 static OWL_DIVIDER(h_clk, "h_clk", "ahbprediv_clk", CMU_BUSCLK1, 2, 2, NULL, 0, 0);
-static OWL_DIVIDER(apb_clk, "apb_clk", "ahb_clk", CMU_BUSCLK1, 14, 2, NULL, 0, 0);
+static OWL_DIVIDER(apb_clk, "apb_clk", "nic_clk", CMU_BUSCLK1, 14, 2, NULL, 0, 0);
 static OWL_DIVIDER(rmii_ref_clk, "rmii_ref_clk", "ethernet_pll_clk", CMU_ETHERNETPLL, 1, 1, rmii_ref_div_table, 0, 0);
 
 /* factor clocks */

@@ -202,6 +203,12 @@ static OWL_FACTOR(de1_clk, "de_clk1", "de_clk", CMU_DECLK, 0, 4, de_factor_table
 static OWL_FACTOR(de2_clk, "de_clk2", "de_clk", CMU_DECLK, 4, 4, de_factor_table, 0, 0);
 
 /* composite clocks */
+static OWL_COMP_DIV(nic_clk, "nic_clk", nic_clk_mux_p,
+			OWL_MUX_HW(CMU_BUSCLK1, 4, 3),
+			{ 0 },
+			OWL_DIVIDER_HW(CMU_BUSCLK1, 16, 2, 0, NULL),
+			0);
+
 static OWL_COMP_DIV(ahbprediv_clk, "ahbprediv_clk", ahbprediv_clk_mux_p,
 			OWL_MUX_HW(CMU_BUSCLK1, 8, 3),
 			{ 0 },

@@ -317,6 +324,10 @@ static OWL_COMP_FIXED_FACTOR(i2c3_clk, "i2c3_clk", "ethernet_pll_clk",
 			OWL_GATE_HW(CMU_DEVCLKEN1, 31, 0),
 			1, 5, 0);
 
+static OWL_COMP_FIXED_FACTOR(ethernet_clk, "ethernet_clk", "ethernet_pll_clk",
+			OWL_GATE_HW(CMU_DEVCLKEN1, 22, 0),
+			1, 20, 0);
+
 static OWL_COMP_DIV(uart0_clk, "uart0_clk", uart_clk_mux_p,
 			OWL_MUX_HW(CMU_UART0CLK, 16, 1),
 			OWL_GATE_HW(CMU_DEVCLKEN1, 6, 0),

@@ -451,6 +462,8 @@ static struct owl_clk_common *s500_clks[] = {
 	&apb_clk.common,
 	&dmac_clk.common,
 	&gpio_clk.common,
+	&nic_clk.common,
+	&ethernet_clk.common,
 };
 
 static struct clk_hw_onecell_data s500_hw_clks = {

@@ -510,6 +523,8 @@ static struct clk_hw_onecell_data s500_hw_clks = {
 		[CLK_APB]		= &apb_clk.common.hw,
 		[CLK_DMAC]		= &dmac_clk.common.hw,
 		[CLK_GPIO]		= &gpio_clk.common.hw,
+		[CLK_NIC]		= &nic_clk.common.hw,
+		[CLK_ETHERNET]		= &ethernet_clk.common.hw,
 	},
 	.num = CLK_NR_CLKS,
 };
Signature · 1 line
2.31.1