Skip to contentSkip to conversation

Minimal build for RISCV

PATCH Superseded Connor Davis 2 participants 5 messages Jun 2, 2021 RISC-V

v5 of 8 Superseded Latest is v8 →

lore
Share & tools
lore
#1 lore raw

PATCH v5 1/2 xen/char: Default HAS_NS16550 to y only for X86 and ARM

In reply to Connor Davis

Defaulting to yes only for X86 and ARM reduces the requirements for a minimal build when porting new architectures.

---
 xen/drivers/char/Kconfig | 1 +
 1 file changed, 1 insertion(+)
xen/drivers/char/Kconfig +1 -0
index b572305657..2ff5b288e2 100644
@@ -1,5 +1,6 @@
 config HAS_NS16550
 	bool "NS16550 UART driver" if ARM
+	default n if RISCV
 	default y
 	help
 	  This selects the 16550-series UART support. For most systems, say Y.
Signature · 1 line
2.31.1
#0 lore raw

v5 cover Minimal build for RISCV

Hi all,

This series introduces a minimal build for RISCV. It is based on Bobby's previous work from last year[0] rebased onto current Xen.

This series provides the patches necessary to get a minimal build working. The build is "minimal" in the sense that it only supports building TARGET=riscv64/head.o. The arch/riscv/riscv64/head.S is just a simple while(1).

The first patch is a mod to non-RISCV bits that enable building a config with !CONFIG_HAS_NS16550.

The second patch adds the make/Kconfig boilerplate alongside head.S and asm-riscv/config.h (head.S references ENTRY that is defined in asm-riscv/config.h).

[0] https://lore.kernel.org/xen-devel/[email protected]/

Thanks,
Connor

--
Changes since v4:
- Dropped patches 2 and 4 as these have been applied
- Moved arch/riscv/head.S to arch/riscv/riscv64/head.S for consistency with ARM.
- Added Bob and myself to MAINTAINERS

Changes since v3:
- Dropped "xen: Fix build when !CONFIG_GRANT_TABLE" since this was applied by Jan
- Adjusted Kconfig condition for building NS16550
- Use bool rather than bool_t
- Removed riscv memory map, as this should probably be done later once the frametable size is figured out
- Consolidated 64-bit #defines in asm-riscv/config.h
- Renamed riscv64_defconfig to tiny64_defconfig, added CONFIG_DEBUG and CONFIG_DEBUG_INFO
- Fixed logic/alignment/whitespace issues in Kconfig files
- Use upstream archlinux riscv64 cross-compiler packages instead of custom built toolchain in docker container

Changes since v2:
- Reduced number of riscv files added to ease review

Changes since v1:
- Dropped "xen/sched: Fix build when NR_CPUS == 1" since this was

    fixed for 4.15

- Moved #ifdef-ary around iommu_enabled to iommu.h
- Moved struct grant_table declaration above ifdef CONFIG_GRANT_TABLE instead of defining an empty struct when !CONFIG_GRANT_TABLE

--
Connor Davis (2):
xen/char: Default HAS_NS16550 to y only for X86 and ARM
xen: Add files needed for minimal riscv build

 MAINTAINERS                             |  8 +++++
 config/riscv64.mk                       |  5 +++
 xen/Makefile                            |  8 +++--
 xen/arch/riscv/Kconfig                  | 47 +++++++++++++++++++++++++
 xen/arch/riscv/Kconfig.debug            |  0
 xen/arch/riscv/Makefile                 |  2 ++
 xen/arch/riscv/Rules.mk                 |  0
 xen/arch/riscv/arch.mk                  | 14 ++++++++
 xen/arch/riscv/configs/tiny64_defconfig | 13 +++++++
 xen/arch/riscv/riscv64/asm-offsets.c    |  0
 xen/arch/riscv/riscv64/head.S           |  6 ++++
 xen/drivers/char/Kconfig                |  1 +
 xen/include/asm-riscv/config.h          | 47 +++++++++++++++++++++++++
 13 files changed, 149 insertions(+), 2 deletions(-)
 create mode 100644 config/riscv64.mk
 create mode 100644 xen/arch/riscv/Kconfig
 create mode 100644 xen/arch/riscv/Kconfig.debug
 create mode 100644 xen/arch/riscv/Makefile
 create mode 100644 xen/arch/riscv/Rules.mk
 create mode 100644 xen/arch/riscv/arch.mk
 create mode 100644 xen/arch/riscv/configs/tiny64_defconfig
 create mode 100644 xen/arch/riscv/riscv64/asm-offsets.c
 create mode 100644 xen/arch/riscv/riscv64/head.S
 create mode 100644 xen/include/asm-riscv/config.h
Signature · 1 line
2.31.1
#4 lore raw

PATCH v5 2/2 xen: Add files needed for minimal riscv build

Add arch-specific makefiles and configs needed to build for riscv. Also add a minimal head.S that is a simple infinite loop. head.o can be built with

$ make XEN_TARGET_ARCH=riscv64 SUBSYSTEMS=xen -C xen tiny64_defconfig
$ make XEN_TARGET_ARCH=riscv64 SUBSYSTEMS=xen -C xen TARGET=riscv64/head.o

No other TARGET is supported at the moment.

---
Bob: I moved back to XEN_TARGET_ARCH=riscv64 because supplying just XEN_TARGET_ARCH=riscv causes TARGET_ARCH == TARGET_SUBARCH, and that broke the build after the recent commit b6ecd5c8bc "build: centralize / unify asm-offsets generation". It also deviates from how x86 and arm work now, so I think this change is for the best for now. That commit is also why the PHONY include target is added in the riscv/Makefile.

---
 MAINTAINERS                             |  8 +++++
 config/riscv64.mk                       |  5 +++
 xen/Makefile                            |  8 +++--
 xen/arch/riscv/Kconfig                  | 47 +++++++++++++++++++++++++
 xen/arch/riscv/Kconfig.debug            |  0
 xen/arch/riscv/Makefile                 |  2 ++
 xen/arch/riscv/Rules.mk                 |  0
 xen/arch/riscv/arch.mk                  | 14 ++++++++
 xen/arch/riscv/configs/tiny64_defconfig | 13 +++++++
 xen/arch/riscv/riscv64/asm-offsets.c    |  0
 xen/arch/riscv/riscv64/head.S           |  6 ++++
 xen/include/asm-riscv/config.h          | 47 +++++++++++++++++++++++++
 12 files changed, 148 insertions(+), 2 deletions(-)
 create mode 100644 config/riscv64.mk
 create mode 100644 xen/arch/riscv/Kconfig
 create mode 100644 xen/arch/riscv/Kconfig.debug
 create mode 100644 xen/arch/riscv/Makefile
 create mode 100644 xen/arch/riscv/Rules.mk
 create mode 100644 xen/arch/riscv/arch.mk
 create mode 100644 xen/arch/riscv/configs/tiny64_defconfig
 create mode 100644 xen/arch/riscv/riscv64/asm-offsets.c
 create mode 100644 xen/arch/riscv/riscv64/head.S
 create mode 100644 xen/include/asm-riscv/config.h
MAINTAINERS +8 -0
index d46b08a0d2..956e71220d 100644
@@ -456,6 +456,14 @@ F:	tools/libs/light/libxl_nonetbuffer.c
 F:	tools/hotplug/Linux/remus-netbuf-setup
 F:	tools/hotplug/Linux/block-drbd-probe
 
+RISCV
+M:	Bob Eshleman <[email protected]>
+R:	Connor Davis <[email protected]>
+S:	Supported
+F:	config/riscv64.mk
+F:	xen/arch/riscv/
+F:	xen/include/asm-riscv/
+
 RTDS SCHEDULER
 M:	Dario Faggioli <[email protected]>
 M:	Meng Xu <[email protected]>
config/riscv64.mk new file +5 -0
new file mode 100644
index 0000000000..a5a21e5fa2
@@ -0,0 +1,5 @@
+CONFIG_RISCV := y
+CONFIG_RISCV_64 := y
+CONFIG_RISCV_$(XEN_OS) := y
+
+CONFIG_XEN_INSTALL_SUFFIX :=
xen/Makefile +6 -2
index 7ce7692354..89879fad4c 100644
@@ -26,7 +26,9 @@ MAKEFLAGS += -rR
 EFI_MOUNTPOINT ?= $(BOOT_DIR)/efi
 
 ARCH=$(XEN_TARGET_ARCH)
-SRCARCH=$(shell echo $(ARCH) | sed -e 's/x86.*/x86/' -e s'/arm\(32\|64\)/arm/g')
+SRCARCH=$(shell echo $(ARCH) | \
+          sed -e 's/x86.*/x86/' -e s'/arm\(32\|64\)/arm/g' \
+              -e s'/riscv.*/riscv/g')
 
 # Don't break if the build process wasn't called from the top level
 # we need XEN_TARGET_ARCH to generate the proper config
@@ -35,7 +37,8 @@ include $(XEN_ROOT)/Config.mk
 # Set ARCH/SUBARCH appropriately.
 export TARGET_SUBARCH  := $(XEN_TARGET_ARCH)
 export TARGET_ARCH     := $(shell echo $(XEN_TARGET_ARCH) | \
-                            sed -e 's/x86.*/x86/' -e s'/arm\(32\|64\)/arm/g')
+                            sed -e 's/x86.*/x86/' -e s'/arm\(32\|64\)/arm/g' \
+                                -e s'/riscv.*/riscv/g')
 
 # Allow someone to change their config file
 export KCONFIG_CONFIG ?= .config
@@ -335,6 +338,7 @@ _clean: delete-unfresh-files
 	$(MAKE) $(clean) xsm
 	$(MAKE) $(clean) crypto
 	$(MAKE) $(clean) arch/arm
+	$(MAKE) $(clean) arch/riscv
 	$(MAKE) $(clean) arch/x86
 	$(MAKE) $(clean) test
 	$(MAKE) -f $(BASEDIR)/tools/kconfig/Makefile.kconfig ARCH=$(ARCH) SRCARCH=$(SRCARCH) clean
xen/arch/riscv/Kconfig new file +47 -0

47 lines not on this page · raw message

xen/arch/riscv/Kconfig.debug new file +0 -0
new file mode 100644
index 0000000000..e69de29bb2
xen/arch/riscv/Makefile new file +2 -0
new file mode 100644
index 0000000000..942e4ffbc1
@@ -0,0 +1,2 @@
+.PHONY: include
+include:
xen/arch/riscv/Rules.mk new file +0 -0
new file mode 100644
index 0000000000..e69de29bb2
xen/arch/riscv/arch.mk new file +14 -0
new file mode 100644
index 0000000000..53dadb8975
@@ -0,0 +1,14 @@
+########################################
+# RISCV-specific definitions
+
+CFLAGS-$(CONFIG_RISCV_64) += -mabi=lp64
+
+riscv-march-$(CONFIG_RISCV_ISA_RV64IMA) := rv64ima
+riscv-march-$(CONFIG_RISCV_ISA_C)       := $(riscv-march-y)c
+
+# Note that -mcmodel=medany is used so that Xen can be mapped
+# into the upper half _or_ the lower half of the address space.
+# -mcmodel=medlow would force Xen into the lower half.
+
+CFLAGS += -march=$(riscv-march-y) -mstrict-align -mcmodel=medany
+CFLAGS += -I$(BASEDIR)/include
xen/arch/riscv/configs/tiny64_defconfig new file +13 -0
new file mode 100644
index 0000000000..3c9a2ff941
@@ -0,0 +1,13 @@
+# CONFIG_SCHED_CREDIT is not set
+# CONFIG_SCHED_RTDS is not set
+# CONFIG_SCHED_NULL is not set
+# CONFIG_SCHED_ARINC653 is not set
+# CONFIG_TRACEBUFFER is not set
+# CONFIG_HYPFS is not set
+# CONFIG_GRANT_TABLE is not set
+# CONFIG_SPECULATIVE_HARDEN_ARRAY is not set
+
+CONFIG_RISCV_64=y
+CONFIG_DEBUG=y
+CONFIG_DEBUG_INFO=y
+CONFIG_EXPERT=y
xen/arch/riscv/riscv64/asm-offsets.c new file +0 -0
new file mode 100644
index 0000000000..e69de29bb2
xen/arch/riscv/riscv64/head.S new file +6 -0
new file mode 100644
index 0000000000..0dbc27ba75
@@ -0,0 +1,6 @@
+#include <asm/config.h>
+
+        .text
+
+ENTRY(start)
+        j  start
xen/include/asm-riscv/config.h new file +47 -0

47 lines not on this page · raw message

Signature · 1 line
2.31.1
#2 lore raw

Re: [PATCH v5 1/2] xen/char: Default HAS_NS16550 to y only for X86 and ARM

In reply to Connor Davis
Quoted 4 lines · Connor Davis

Defaulting to yes only for X86 and ARM reduces the requirements for a minimal build when porting new architectures.

Please can you accumulate tags you've already got into re-submissions, so the status of patches is clear and committers will know what is ready to go in without having to hunt down anything? In the case here you've lost my A-b.

Jan

#3 lore raw

Re: [PATCH v5 1/2] xen/char: Default HAS_NS16550 to y only for X86 and ARM

Quoted 11 lines · Jan Beulich
Quoted 4 lines · Connor Davis

Defaulting to yes only for X86 and ARM reduces the requirements for a minimal build when porting new architectures.

Please can you accumulate tags you've already got into re-submissions, so the status of patches is clear and committers will know what is ready to go in without having to hunt down anything? In the case here you've lost my A-b.

Jan

Oops, sorry about that. Will resend shortly.

Thanks,
Connor