Skip to contentSkip to conversation

OPP: Replace custom set_opp() with config_regulators()

PATCH New Viresh Kumar 1 participant 6 messages Jul 1, 2022

Subsystems (2)
Power management core Operating performance points (OPP)
lore
Share & tools
lore

Viresh Kumar

author
#0 lore raw

v2 cover OPP: Replace custom set_opp() with config_regulators()

Hi,

Currently the custom set_opp() helper, which is implemented only for OMAP, is responsible to set both clock and regulators for the device and may end up doing tricky stuff behind the scene. This makes the OPP core contain special code to support it.

This patch series tries to streamline the code path in _set_opp() in the OPP core and minimize the platform specific code within it. The platforms provide a config_regulators() callback now, from which they should only program the regulators in their preferred sequence. Rest of the code sequence to program clk, bw, required-opps, etc is common across all device and platform types and is present in the OPP core.

Keerthy/Dave: I couldn't test it on omap, can any of you do that please ? It builds just fine though. Also maybe you can simplify the OPP driver to drop all restoration logic on failures, as the OPP core doesn't do any of it as well. I can add a patch for that if you guys are fine with it.

This is pushed here along with other dependencies:

git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm.git opp/linux-next

V1->V2:
- Moved back to 80 column width instead of 100.
- Rebased over updated set-config API changes, which forced minor changes to this series as well.

Thanks.

--
Viresh

Viresh Kumar (5):
OPP: Add support for config_regulators() helper
OPP: Make _generic_set_opp_regulator() a config_regulators() interface
OPP: Add dev_pm_opp_get_supplies()
OPP: ti: Migrate to config_regulators()
OPP: Remove custom OPP helper support

 drivers/opp/core.c          | 218 +++++++++++++-----------------------
 drivers/opp/opp.h           |   9 +-
 drivers/opp/ti-opp-supply.c |  74 ++++++------
 include/linux/pm_opp.h      |  46 ++------
 4 files changed, 125 insertions(+), 222 deletions(-)
Signature · 1 line
2.31.1.272.g89b43f80a514
author
#1 lore raw

PATCH v2 1/5 OPP: Add support for config_regulators() helper

Extend the dev_pm_opp_set_config() interface to allow adding config_regulators() helpers. This helper will be called to set the voltages of the regulators from the regular path in _set_opp(), while we are trying to change the OPP.

This will eventually replace the custom set_opp() helper.

Tested-by Dmitry Osipenko <[email protected]>
Signed-off-by Viresh Kumar <[email protected]>
---
 drivers/opp/core.c     | 68 +++++++++++++++++++++++++++++++++++++++++-
 drivers/opp/opp.h      |  2 ++
 include/linux/pm_opp.h |  6 ++++
 3 files changed, 75 insertions(+), 1 deletion(-)
drivers/opp/core.c +67 -1
index 75bb570d30e4..d5e1ae6f5ea1 100644
@@ -1185,6 +1185,17 @@ static int _set_opp(struct device *dev, struct opp_table *opp_table,
 			dev_err(dev, "Failed to set bw: %d\n", ret);
 			return ret;
 		}
+
+		if (opp_table->config_regulators) {
+			ret = opp_table->config_regulators(dev, old_opp, opp,
+							   opp_table->regulators,
+							   opp_table->regulator_count);
+			if (ret) {
+				dev_err(dev, "Failed to set regulator voltages: %d\n",
+					ret);
+				return ret;
+			}
+		}
 	}
 
 	if (opp_table->set_opp) {

@@ -1202,6 +1213,17 @@ static int _set_opp(struct device *dev, struct opp_table *opp_table,
 
 	/* Scaling down? Configure required OPPs after frequency */
 	if (scaling_down) {
+		if (opp_table->config_regulators) {
+			ret = opp_table->config_regulators(dev, old_opp, opp,
+							   opp_table->regulators,
+							   opp_table->regulator_count);
+			if (ret) {
+				dev_err(dev, "Failed to set regulator voltages: %d\n",
+					ret);
+				return ret;
+			}
+		}
+
 		ret = _set_opp_bw(opp_table, opp, dev);
 		if (ret) {
 			dev_err(dev, "Failed to set bw: %d\n", ret);

@@ -2246,6 +2268,38 @@ static void _opp_unregister_set_opp_helper(struct opp_table *opp_table)
 	}
 }
 
+/**
+ * _opp_set_config_regulators_helper() - Register custom set regulator helper.
+ * @dev: Device for which the helper is getting registered.
+ * @config_regulators: Custom set regulator helper.
+ *
+ * This is useful to support platforms with multiple regulators per device.
+ *
+ * This must be called before any OPPs are initialized for the device.
+ */
+static int _opp_set_config_regulators_helper(struct opp_table *opp_table,
+		struct device *dev, config_regulators_t config_regulators)
+{
+	/* Another CPU that shares the OPP table has set the helper ? */
+	if (!opp_table->config_regulators)
+		opp_table->config_regulators = config_regulators;
+
+	return 0;
+}
+
+/**
+ * _opp_put_config_regulators_helper() - Releases resources blocked for
+ *					 config_regulators helper.
+ * @opp_table: OPP table returned from _opp_set_config_regulators_helper().
+ *
+ * Release resources blocked for platform specific config_regulators helper.
+ */
+static void _opp_put_config_regulators_helper(struct opp_table *opp_table)
+{
+	if (opp_table->config_regulators)
+		opp_table->config_regulators = NULL;
+}
+
 static void _detach_genpd(struct opp_table *opp_table)
 {
 	int index;

@@ -2372,8 +2426,10 @@ static void _opp_clear_config(struct opp_config_data *data)
 		_opp_put_regulators(data->opp_table);
 	if (data->flags & OPP_CONFIG_SUPPORTED_HW)
 		_opp_put_supported_hw(data->opp_table);
-	if (data->flags & OPP_CONFIG_REGULATOR_HELPER)
+	if (data->flags & OPP_CONFIG_REGULATOR_HELPER) {
+		_opp_put_config_regulators_helper(data->opp_table);
 		_opp_unregister_set_opp_helper(data->opp_table);
+	}
 	if (data->flags & OPP_CONFIG_PROP_NAME)
 		_opp_put_prop_name(data->opp_table);
 	if (data->flags & OPP_CONFIG_CLK)

@@ -2455,6 +2511,16 @@ int dev_pm_opp_set_config(struct device *dev, struct dev_pm_opp_config *config)
 		data->flags |= OPP_CONFIG_REGULATOR_HELPER;
 	}
 
+	/* Configure config_regulators helper */
+	if (config->config_regulators) {
+		ret = _opp_set_config_regulators_helper(opp_table, dev,
+						config->config_regulators);
+		if (ret)
+			goto err;
+
+		data->flags |= OPP_CONFIG_REGULATOR_HELPER;
+	}
+
 	/* Configure supported hardware */
 	if (config->supported_hw) {
 		ret = _opp_set_supported_hw(opp_table, config->supported_hw,
drivers/opp/opp.h +2 -0
index d652f0cc84f1..45fd40737159 100644
@@ -172,6 +172,7 @@ enum opp_table_access {
  * @prop_name: A name to postfix to many DT properties, while parsing them.
  * @clk_configured: Clock name is configured by the platform.
  * @clk: Device's clock handle
+ * @config_regulators: Platform specific config_regulators() callback.
  * @regulators: Supply regulators
  * @regulator_count: Number of power supply regulators. Its value can be -1
  * (uninitialized), 0 (no opp-microvolt property) or > 0 (has opp-microvolt

@@ -224,6 +225,7 @@ struct opp_table {
 	const char *prop_name;
 	bool clk_configured;
 	struct clk *clk;
+	config_regulators_t config_regulators;
 	struct regulator **regulators;
 	int regulator_count;
 	struct icc_path **paths;
include/linux/pm_opp.h +6 -0
index 26653be21dc0..721aa02bcaaf 100644
@@ -90,12 +90,17 @@ struct dev_pm_set_opp_data {
 	struct device *dev;
 };
 
+typedef int (*config_regulators_t)(struct device *dev,
+			struct dev_pm_opp *old_opp, struct dev_pm_opp *new_opp,
+			struct regulator **regulators, unsigned int count);
+
 /**
  * struct dev_pm_opp_config - Device OPP configuration values
  * @clk_names: Clk name.
  * @clk_count: Number of clocks, max 1 for now.
  * @prop_name: Name to postfix to properties.
  * @set_opp: Custom set OPP helper.
+ * @config_regulators: Custom set regulator helper.
  * @supported_hw: Array of hierarchy of versions to match.
  * @supported_hw_count: Number of elements in the array.
  * @regulator_names: Array of pointers to the names of the regulator.

@@ -111,6 +116,7 @@ struct dev_pm_opp_config {
 	unsigned int clk_count;
 	const char *prop_name;
 	int (*set_opp)(struct dev_pm_set_opp_data *data);
+	config_regulators_t config_regulators;
 	unsigned int *supported_hw;
 	unsigned int supported_hw_count;
 	const char * const *regulator_names;
Signature · 1 line
2.31.1.272.g89b43f80a514
author
#2 lore raw

PATCH v2 2/5 OPP: Make _generic_set_opp_regulator() a config_regulators() interface

In reply to Viresh Kumar

In order to reuse the same code path, i.e. clk_set_rate() from _set_opp(), migrate _generic_set_opp_regulator() to implement a config_regulators() interface.

It is renamed to _opp_config_regulator_single() and is set as the preferred config_regulators() interface whenever we have a single regulator available.

Note that this also drops code responsible for restoring the voltage/freq in case of errors. We aren't handling that properly currently, restoring only some of the resources while leaving others out (like bandwidth and required OPPs). It is better to drop all of it instead of partial restoration.

Tested-by Dmitry Osipenko <[email protected]>
Signed-off-by Viresh Kumar <[email protected]>
---
 drivers/opp/core.c | 51 +++++++++++-----------------------------------
 1 file changed, 12 insertions(+), 39 deletions(-)
drivers/opp/core.c +12 -39
index d5e1ae6f5ea1..df0135f2cfec 100644
@@ -896,62 +896,34 @@ static inline int _generic_set_opp_clk_only(struct device *dev, struct clk *clk,
 	return ret;
 }
 
-static int _generic_set_opp_regulator(struct opp_table *opp_table,
-				      struct device *dev,
-				      struct dev_pm_opp *opp,
-				      unsigned long freq,
-				      int scaling_down)
+static int _opp_config_regulator_single(struct device *dev,
+			struct dev_pm_opp *old_opp, struct dev_pm_opp *new_opp,
+			struct regulator **regulators, unsigned int count)
 {
-	struct regulator *reg = opp_table->regulators[0];
-	struct dev_pm_opp *old_opp = opp_table->current_opp;
+	struct regulator *reg = regulators[0];
 	int ret;
 
 	/* This function only supports single regulator per device */
-	if (WARN_ON(opp_table->regulator_count > 1)) {
+	if (WARN_ON(count > 1)) {
 		dev_err(dev, "multiple regulators are not supported\n");
 		return -EINVAL;
 	}
 
-	/* Scaling up? Scale voltage before frequency */
-	if (!scaling_down) {
-		ret = _set_opp_voltage(dev, reg, opp->supplies);
-		if (ret)
-			goto restore_voltage;
-	}
-
-	/* Change frequency */
-	ret = _generic_set_opp_clk_only(dev, opp_table->clk, freq);
+	ret = _set_opp_voltage(dev, reg, new_opp->supplies);
 	if (ret)
-		goto restore_voltage;
-
-	/* Scaling down? Scale voltage after frequency */
-	if (scaling_down) {
-		ret = _set_opp_voltage(dev, reg, opp->supplies);
-		if (ret)
-			goto restore_freq;
-	}
+		return ret;
 
 	/*
 	 * Enable the regulator after setting its voltages, otherwise it breaks
 	 * some boot-enabled regulators.
 	 */
-	if (unlikely(!opp_table->enabled)) {
+	if (unlikely(!new_opp->opp_table->enabled)) {
 		ret = regulator_enable(reg);
 		if (ret < 0)
 			dev_warn(dev, "Failed to enable regulator: %d", ret);
 	}
 
 	return 0;
-
-restore_freq:
-	if (_generic_set_opp_clk_only(dev, opp_table->clk, old_opp->rate))
-		dev_err(dev, "%s: failed to restore old-freq (%lu Hz)\n",
-			__func__, old_opp->rate);
-restore_voltage:
-	/* This shouldn't harm even if the voltages weren't updated earlier */
-	_set_opp_voltage(dev, reg, old_opp->supplies);
-
-	return ret;
 }
 
 static int _set_opp_bw(const struct opp_table *opp_table,

@@ -1200,9 +1172,6 @@ static int _set_opp(struct device *dev, struct opp_table *opp_table,
 
 	if (opp_table->set_opp) {
 		ret = _set_opp_custom(opp_table, dev, opp, freq);
-	} else if (opp_table->regulators) {
-		ret = _generic_set_opp_regulator(opp_table, dev, opp, freq,
-						 scaling_down);
 	} else {
 		/* Only frequency scaling */
 		ret = _generic_set_opp_clk_only(dev, opp_table->clk, freq);

@@ -2113,6 +2082,10 @@ static int _opp_set_regulators(struct opp_table *opp_table, struct device *dev,
 	}
 	mutex_unlock(&opp_table->lock);
 
+	/* Set generic config_regulators() for single regulators here */
+	if (count == 1)
+		opp_table->config_regulators = _opp_config_regulator_single;
+
 	return 0;
 
 free_regulators:
Signature · 1 line
2.31.1.272.g89b43f80a514
author
#3 lore raw

PATCH v2 3/5 OPP: Add dev_pm_opp_get_supplies()

In reply to Viresh Kumar

We already have an API for getting voltage information for a single regulator, dev_pm_opp_get_voltage(), but there is nothing available for multiple regulator case.

This patch adds a new API, dev_pm_opp_get_supplies(), to get all information related to the supplies for an OPP.

Tested-by Dmitry Osipenko <[email protected]>
Signed-off-by Viresh Kumar <[email protected]>
---
 drivers/opp/core.c     | 25 +++++++++++++++++++++++++
 include/linux/pm_opp.h |  7 +++++++
 2 files changed, 32 insertions(+)
drivers/opp/core.c +25 -0
index df0135f2cfec..ee842a3d27a6 100644
@@ -117,6 +117,31 @@ unsigned long dev_pm_opp_get_voltage(struct dev_pm_opp *opp)
 }
 EXPORT_SYMBOL_GPL(dev_pm_opp_get_voltage);
 
+/**
+ * dev_pm_opp_get_supplies() - Gets the supply information corresponding to an opp
+ * @opp:	opp for which voltage has to be returned for
+ * @supplies:	Placeholder for copying the supply information.
+ *
+ * Return: negative error number on failure, 0 otherwise on success after
+ * setting @supplies.
+ *
+ * This can be used for devices with any number of power supplies. The caller
+ * must ensure the @supplies array must contain space for each regulator.
+ */
+int dev_pm_opp_get_supplies(struct dev_pm_opp *opp,
+			    struct dev_pm_opp_supply *supplies)
+{
+	if (IS_ERR_OR_NULL(opp) || !supplies) {
+		pr_err("%s: Invalid parameters\n", __func__);
+		return -EINVAL;
+	}
+
+	memcpy(supplies, opp->supplies,
+	       sizeof(*supplies) * opp->opp_table->regulator_count);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(dev_pm_opp_get_supplies);
+
 /**
  * dev_pm_opp_get_power() - Gets the power corresponding to an opp
  * @opp:	opp for which power has to be returned for
include/linux/pm_opp.h +7 -0
index 721aa02bcaaf..4c1cce06a61c 100644
@@ -132,6 +132,8 @@ void dev_pm_opp_put_opp_table(struct opp_table *opp_table);
 
 unsigned long dev_pm_opp_get_voltage(struct dev_pm_opp *opp);
 
+int dev_pm_opp_get_supplies(struct dev_pm_opp *opp, struct dev_pm_opp_supply *supplies);
+
 unsigned long dev_pm_opp_get_power(struct dev_pm_opp *opp);
 
 unsigned long dev_pm_opp_get_freq(struct dev_pm_opp *opp);

@@ -220,6 +222,11 @@ static inline unsigned long dev_pm_opp_get_voltage(struct dev_pm_opp *opp)
 	return 0;
 }
 
+static inline int dev_pm_opp_get_supplies(struct dev_pm_opp *opp, struct dev_pm_opp_supply *supplies)
+{
+	return -EOPNOTSUPP;
+}
+
 static inline unsigned long dev_pm_opp_get_power(struct dev_pm_opp *opp)
 {
 	return 0;
Signature · 1 line
2.31.1.272.g89b43f80a514
author
#4 lore raw

PATCH v2 4/5 OPP: ti: Migrate to config_regulators()

In reply to Viresh Kumar

The OPP core now provides config_regulators() interface, which needs the platforms to just set the OPP voltages instead of both clk and voltage. The clock is set by the OPP core instead and hence reduces code redundancy.

Migrate the only user of the custom set_opp() interface to config_regulators().

Signed-off-by Viresh Kumar <[email protected]>
---
 drivers/opp/ti-opp-supply.c | 74 +++++++++++++++++--------------------
 1 file changed, 34 insertions(+), 40 deletions(-)
drivers/opp/ti-opp-supply.c +34 -40
index 26e929377ebd..f1f881140fa2 100644
@@ -36,11 +36,15 @@ struct ti_opp_supply_optimum_voltage_table {
  * @vdd_table:	Optimized voltage mapping table
  * @num_vdd_table: number of entries in vdd_table
  * @vdd_absolute_max_voltage_uv: absolute maximum voltage in UV for the supply
+ * @old_supplies: Placeholder for supplies information for old OPP.
+ * @new_supplies: Placeholder for supplies information for new OPP.
  */
 struct ti_opp_supply_data {
 	struct ti_opp_supply_optimum_voltage_table *vdd_table;
 	u32 num_vdd_table;
 	u32 vdd_absolute_max_voltage_uv;
+	struct dev_pm_opp_supply old_supplies[2];
+	struct dev_pm_opp_supply new_supplies[2];
 };
 
 static struct ti_opp_supply_data opp_data;

@@ -266,27 +270,32 @@ static int _opp_set_voltage(struct device *dev,
 	return 0;
 }
 
-/**
- * ti_opp_supply_set_opp() - do the opp supply transition
- * @data:	information on regulators and new and old opps provided by
- *		opp core to use in transition
- *
- * Return: If successful, 0, else appropriate error value.
- */
-static int ti_opp_supply_set_opp(struct dev_pm_set_opp_data *data)
+/* Do the opp supply transition */
+static int ti_opp_config_regulators(struct device *dev,
+			struct dev_pm_opp *old_opp, struct dev_pm_opp *new_opp,
+			struct regulator **regulators, unsigned int count)
 {
-	struct dev_pm_opp_supply *old_supply_vdd = &data->old_opp.supplies[0];
-	struct dev_pm_opp_supply *old_supply_vbb = &data->old_opp.supplies[1];
-	struct dev_pm_opp_supply *new_supply_vdd = &data->new_opp.supplies[0];
-	struct dev_pm_opp_supply *new_supply_vbb = &data->new_opp.supplies[1];
-	struct device *dev = data->dev;
-	unsigned long old_freq = data->old_opp.rate, freq = data->new_opp.rate;
-	struct clk *clk = data->clk;
-	struct regulator *vdd_reg = data->regulators[0];
-	struct regulator *vbb_reg = data->regulators[1];
+	struct dev_pm_opp_supply *old_supply_vdd = &opp_data.old_supplies[0];
+	struct dev_pm_opp_supply *old_supply_vbb = &opp_data.old_supplies[1];
+	struct dev_pm_opp_supply *new_supply_vdd = &opp_data.new_supplies[0];
+	struct dev_pm_opp_supply *new_supply_vbb = &opp_data.new_supplies[1];
+	struct regulator *vdd_reg = regulators[0];
+	struct regulator *vbb_reg = regulators[1];
+	unsigned long old_freq, freq;
 	int vdd_uv;
 	int ret;
 
+	/* We must have two regulators here */
+	WARN_ON(count != 2);
+
+	/* Fetch supplies and freq information from OPP core */
+	ret = dev_pm_opp_get_supplies(new_opp, opp_data.new_supplies);
+	WARN_ON(ret);
+
+	old_freq = dev_pm_opp_get_freq(old_opp);
+	freq = dev_pm_opp_get_freq(new_opp);
+	WARN_ON(!old_freq || !freq);
+
 	vdd_uv = _get_optimal_vdd_voltage(dev, &opp_data,
 					  new_supply_vdd->u_volt);
 

@@ -303,39 +312,24 @@ static int ti_opp_supply_set_opp(struct dev_pm_set_opp_data *data)
 		ret = _opp_set_voltage(dev, new_supply_vbb, 0, vbb_reg, "vbb");
 		if (ret)
 			goto restore_voltage;
-	}
-
-	/* Change frequency */
-	dev_dbg(dev, "%s: switching OPP: %lu Hz --> %lu Hz\n",
-		__func__, old_freq, freq);
-
-	ret = clk_set_rate(clk, freq);
-	if (ret) {
-		dev_err(dev, "%s: failed to set clock rate: %d\n", __func__,
-			ret);
-		goto restore_voltage;
-	}
-
-	/* Scaling down? Scale voltage after frequency */
-	if (freq < old_freq) {
+	} else {
 		ret = _opp_set_voltage(dev, new_supply_vbb, 0, vbb_reg, "vbb");
 		if (ret)
-			goto restore_freq;
+			goto restore_voltage;
 
 		ret = _opp_set_voltage(dev, new_supply_vdd, vdd_uv, vdd_reg,
 				       "vdd");
 		if (ret)
-			goto restore_freq;
+			goto restore_voltage;
 	}
 
 	return 0;
 
-restore_freq:
-	ret = clk_set_rate(clk, old_freq);
-	if (ret)
-		dev_err(dev, "%s: failed to restore old-freq (%lu Hz)\n",
-			__func__, old_freq);
 restore_voltage:
+	/* Fetch old supplies information only if required */
+	ret = dev_pm_opp_get_supplies(old_opp, opp_data.old_supplies);
+	WARN_ON(ret);
+
 	/* This shouldn't harm even if the voltages weren't updated earlier */
 	if (old_supply_vdd->u_volt) {
 		ret = _opp_set_voltage(dev, old_supply_vbb, 0, vbb_reg, "vbb");

@@ -383,7 +377,7 @@ static int ti_opp_supply_probe(struct platform_device *pdev)
 	const struct ti_opp_supply_of_data *of_data;
 	int ret = 0;
 	struct dev_pm_opp_config config = {
-		.set_opp = ti_opp_supply_set_opp,
+		.config_regulators = ti_opp_config_regulators,
 	};
 
 	match = of_match_device(ti_opp_supply_of_match, dev);
Signature · 1 line
2.31.1.272.g89b43f80a514
author
#5 lore raw

PATCH v2 5/5 OPP: Remove custom OPP helper support

In reply to Viresh Kumar

The only user of the custom helper is migrated to use config_regulators() interface. Remove the now unused custom OPP helper support.

This cleans up _set_opp() and leaves a single code path to be used by all users.

Tested-by Dmitry Osipenko <[email protected]>
Signed-off-by Viresh Kumar <[email protected]>
---
 drivers/opp/core.c     | 132 +----------------------------------------
 drivers/opp/opp.h      |   7 ---
 include/linux/pm_opp.h |  35 -----------
 3 files changed, 2 insertions(+), 172 deletions(-)
drivers/opp/core.c +2 -130
index ee842a3d27a6..024a9106b6d2 100644
@@ -979,36 +979,6 @@ static int _set_opp_bw(const struct opp_table *opp_table,
 	return 0;
 }
 
-static int _set_opp_custom(const struct opp_table *opp_table,
-			   struct device *dev, struct dev_pm_opp *opp,
-			   unsigned long freq)
-{
-	struct dev_pm_set_opp_data *data = opp_table->set_opp_data;
-	struct dev_pm_opp *old_opp = opp_table->current_opp;
-	int size;
-
-	/*
-	 * We support this only if dev_pm_opp_set_config() was called
-	 * earlier to set regulators.
-	 */
-	if (opp_table->sod_supplies) {
-		size = sizeof(*old_opp->supplies) * opp_table->regulator_count;
-		memcpy(data->old_opp.supplies, old_opp->supplies, size);
-		memcpy(data->new_opp.supplies, opp->supplies, size);
-		data->regulator_count = opp_table->regulator_count;
-	} else {
-		data->regulator_count = 0;
-	}
-
-	data->regulators = opp_table->regulators;
-	data->clk = opp_table->clk;
-	data->dev = dev;
-	data->old_opp.rate = old_opp->rate;
-	data->new_opp.rate = freq;
-
-	return opp_table->set_opp(data);
-}
-
 static int _set_required_opp(struct device *dev, struct device *pd_dev,
 			     struct dev_pm_opp *opp, int i)
 {

@@ -1195,13 +1165,7 @@ static int _set_opp(struct device *dev, struct opp_table *opp_table,
 		}
 	}
 
-	if (opp_table->set_opp) {
-		ret = _set_opp_custom(opp_table, dev, opp, freq);
-	} else {
-		/* Only frequency scaling */
-		ret = _generic_set_opp_clk_only(dev, opp_table->clk, freq);
-	}
-
+	ret = _generic_set_opp_clk_only(dev, opp_table->clk, freq);
 	if (ret)
 		return ret;
 

@@ -2065,7 +2029,6 @@ static void _opp_put_prop_name(struct opp_table *opp_table)
 static int _opp_set_regulators(struct opp_table *opp_table, struct device *dev,
 			       const char * const names[], unsigned int count)
 {
-	struct dev_pm_opp_supply *supplies;
 	struct regulator *reg;
 	int ret, i;
 

@@ -2093,20 +2056,6 @@ static int _opp_set_regulators(struct opp_table *opp_table, struct device *dev,
 
 	opp_table->regulator_count = count;
 
-	supplies = kmalloc_array(count * 2, sizeof(*supplies), GFP_KERNEL);
-	if (!supplies) {
-		ret = -ENOMEM;
-		goto free_regulators;
-	}
-
-	mutex_lock(&opp_table->lock);
-	opp_table->sod_supplies = supplies;
-	if (opp_table->set_opp_data) {
-		opp_table->set_opp_data->old_opp.supplies = supplies;
-		opp_table->set_opp_data->new_opp.supplies = supplies + count;
-	}
-	mutex_unlock(&opp_table->lock);
-
 	/* Set generic config_regulators() for single regulators here */
 	if (count == 1)
 		opp_table->config_regulators = _opp_config_regulator_single;

@@ -2143,16 +2092,6 @@ static void _opp_put_regulators(struct opp_table *opp_table)
 	for (i = opp_table->regulator_count - 1; i >= 0; i--)
 		regulator_put(opp_table->regulators[i]);
 
-	mutex_lock(&opp_table->lock);
-	if (opp_table->set_opp_data) {
-		opp_table->set_opp_data->old_opp.supplies = NULL;
-		opp_table->set_opp_data->new_opp.supplies = NULL;
-	}
-
-	kfree(opp_table->sod_supplies);
-	opp_table->sod_supplies = NULL;
-	mutex_unlock(&opp_table->lock);
-
 	kfree(opp_table->regulators);
 	opp_table->regulators = NULL;
 	opp_table->regulator_count = -1;

@@ -2211,61 +2150,6 @@ static void _opp_put_clknames(struct opp_table *opp_table)
 	}
 }
 
-/**
- * _opp_register_set_opp_helper() - Register custom set OPP helper
- * @dev: Device for which the helper is getting registered.
- * @set_opp: Custom set OPP helper.
- *
- * This is useful to support complex platforms (like platforms with multiple
- * regulators per device), instead of the generic OPP set rate helper.
- *
- * This must be called before any OPPs are initialized for the device.
- */
-static int _opp_register_set_opp_helper(struct opp_table *opp_table,
-	struct device *dev, int (*set_opp)(struct dev_pm_set_opp_data *data))
-{
-	struct dev_pm_set_opp_data *data;
-
-	/* Another CPU that shares the OPP table has set the helper ? */
-	if (opp_table->set_opp)
-		return 0;
-
-	data = kzalloc(sizeof(*data), GFP_KERNEL);
-	if (!data)
-		return -ENOMEM;
-
-	mutex_lock(&opp_table->lock);
-	opp_table->set_opp_data = data;
-	if (opp_table->sod_supplies) {
-		data->old_opp.supplies = opp_table->sod_supplies;
-		data->new_opp.supplies = opp_table->sod_supplies +
-					 opp_table->regulator_count;
-	}
-	mutex_unlock(&opp_table->lock);
-
-	opp_table->set_opp = set_opp;
-
-	return 0;
-}
-
-/**
- * _opp_unregister_set_opp_helper() - Releases resources blocked for set_opp helper
- * @opp_table: OPP table returned from _opp_register_set_opp_helper().
- *
- * Release resources blocked for platform specific set_opp helper.
- */
-static void _opp_unregister_set_opp_helper(struct opp_table *opp_table)
-{
-	if (opp_table->set_opp) {
-		opp_table->set_opp = NULL;
-
-		mutex_lock(&opp_table->lock);
-		kfree(opp_table->set_opp_data);
-		opp_table->set_opp_data = NULL;
-		mutex_unlock(&opp_table->lock);
-	}
-}
-
 /**
  * _opp_set_config_regulators_helper() - Register custom set regulator helper.
  * @dev: Device for which the helper is getting registered.

@@ -2424,10 +2308,8 @@ static void _opp_clear_config(struct opp_config_data *data)
 		_opp_put_regulators(data->opp_table);
 	if (data->flags & OPP_CONFIG_SUPPORTED_HW)
 		_opp_put_supported_hw(data->opp_table);
-	if (data->flags & OPP_CONFIG_REGULATOR_HELPER) {
+	if (data->flags & OPP_CONFIG_REGULATOR_HELPER)
 		_opp_put_config_regulators_helper(data->opp_table);
-		_opp_unregister_set_opp_helper(data->opp_table);
-	}
 	if (data->flags & OPP_CONFIG_PROP_NAME)
 		_opp_put_prop_name(data->opp_table);
 	if (data->flags & OPP_CONFIG_CLK)

@@ -2499,16 +2381,6 @@ int dev_pm_opp_set_config(struct device *dev, struct dev_pm_opp_config *config)
 		data->flags |= OPP_CONFIG_PROP_NAME;
 	}
 
-	/* Configure opp helper */
-	if (config->set_opp) {
-		ret = _opp_register_set_opp_helper(opp_table, dev,
-						   config->set_opp);
-		if (ret)
-			goto err;
-
-		data->flags |= OPP_CONFIG_REGULATOR_HELPER;
-	}
-
 	/* Configure config_regulators helper */
 	if (config->config_regulators) {
 		ret = _opp_set_config_regulators_helper(opp_table, dev,
drivers/opp/opp.h +0 -7
index 45fd40737159..13abe991e811 100644
@@ -182,9 +182,6 @@ enum opp_table_access {
  * @enabled: Set to true if the device's resources are enabled/configured.
  * @genpd_performance_state: Device's power domain support performance state.
  * @is_genpd: Marks if the OPP table belongs to a genpd.
- * @set_opp: Platform specific set_opp callback
- * @sod_supplies: Set opp data supplies
- * @set_opp_data: Data to be passed to set_opp callback
  * @dentry:	debugfs dentry pointer of the real device directory (not links).
  * @dentry_name: Name of the real dentry.
  *

@@ -234,10 +231,6 @@ struct opp_table {
 	bool genpd_performance_state;
 	bool is_genpd;
 
-	int (*set_opp)(struct dev_pm_set_opp_data *data);
-	struct dev_pm_opp_supply *sod_supplies;
-	struct dev_pm_set_opp_data *set_opp_data;
-
 #ifdef CONFIG_DEBUG_FS
 	struct dentry *dentry;
 	char dentry_name[NAME_MAX];
include/linux/pm_opp.h +0 -35
index 4c1cce06a61c..25a1e15cb7fe 100644
@@ -57,39 +57,6 @@ struct dev_pm_opp_icc_bw {
 	u32 peak;
 };
 
-/**
- * struct dev_pm_opp_info - OPP freq/voltage/current values
- * @rate:	Target clk rate in hz
- * @supplies:	Array of voltage/current values for all power supplies
- *
- * This structure stores the freq/voltage/current values for a single OPP.
- */
-struct dev_pm_opp_info {
-	unsigned long rate;
-	struct dev_pm_opp_supply *supplies;
-};
-
-/**
- * struct dev_pm_set_opp_data - Set OPP data
- * @old_opp:	Old OPP info
- * @new_opp:	New OPP info
- * @regulators:	Array of regulator pointers
- * @regulator_count: Number of regulators
- * @clk:	Pointer to clk
- * @dev:	Pointer to the struct device
- *
- * This structure contains all information required for setting an OPP.
- */
-struct dev_pm_set_opp_data {
-	struct dev_pm_opp_info old_opp;
-	struct dev_pm_opp_info new_opp;
-
-	struct regulator **regulators;
-	unsigned int regulator_count;
-	struct clk *clk;
-	struct device *dev;
-};
-
 typedef int (*config_regulators_t)(struct device *dev,
 			struct dev_pm_opp *old_opp, struct dev_pm_opp *new_opp,
 			struct regulator **regulators, unsigned int count);

@@ -99,7 +66,6 @@ typedef int (*config_regulators_t)(struct device *dev,
  * @clk_names: Clk name.
  * @clk_count: Number of clocks, max 1 for now.
  * @prop_name: Name to postfix to properties.
- * @set_opp: Custom set OPP helper.
  * @config_regulators: Custom set regulator helper.
  * @supported_hw: Array of hierarchy of versions to match.
  * @supported_hw_count: Number of elements in the array.

@@ -115,7 +81,6 @@ struct dev_pm_opp_config {
 	const char * const *clk_names;
 	unsigned int clk_count;
 	const char *prop_name;
-	int (*set_opp)(struct dev_pm_set_opp_data *data);
 	config_regulators_t config_regulators;
 	unsigned int *supported_hw;
 	unsigned int supported_hw_count;
Signature · 1 line
2.31.1.272.g89b43f80a514