Skip to contentSkip to conversation

staging: rtl8192e: Rename or remove CamelCase variables from r8192_priv

PATCH New Philipp Hortmann 1 participant 10 messages Jan 18, 2023 Staging

lore
Share & tools
lore

Philipp Hortmann

author
#0 lore raw

cover staging: rtl8192e: Rename or remove CamelCase variables from r8192_priv

Rename or remove variables to avoid CamelCase which is not accepted by checkpatch.

Tested with rtl8192e
Transferred this patch over wlan connection of rtl8192e

Philipp Hortmann (9):
staging: rtl8192e: Rename LongRetryL.., ShortRetryL.. and
ReceiveConfig
staging: rtl8192e: Rename LastRxDescTSF, LoopbackMode and pFirmware
staging: rtl8192e: Rename PHYRegDef, CurrentChannelBW and CustomerID
staging: rtl8192e: Remove unused variable SifsTime
staging: rtl8192e: Remove unused variable framesyncC34
staging: rtl8192e: Remove unused variable PwrDomainProtect
staging: rtl8192e: Remove unused variable H2CTxCmdSeq
staging: rtl8192e: Remove unused variable RF_C_TxPwDiff
staging: rtl8192e: Remove unused variable DM_Type

 .../rtl8192e/rtl8192e/r8190P_rtl8256.c        |   4 +-
 .../staging/rtl8192e/rtl8192e/r8192E_dev.c    |  70 ++++---
 .../rtl8192e/rtl8192e/r8192E_firmware.c       |   4 +-
 .../staging/rtl8192e/rtl8192e/r8192E_phy.c    | 192 +++++++++---------
 drivers/staging/rtl8192e/rtl8192e/rtl_core.c  |  12 +-
 drivers/staging/rtl8192e/rtl8192e/rtl_core.h  |  26 +--
 drivers/staging/rtl8192e/rtl8192e/rtl_dm.c    |  38 ++--
 drivers/staging/rtl8192e/rtl8192e/rtl_dm.h    |   2 -
 8 files changed, 165 insertions(+), 183 deletions(-)
Signature · 1 line
2.39.0
author
#1 lore raw

PATCH 1/9 staging: rtl8192e: Rename LongRetryL.., ShortRetryL.. and ReceiveConfig

Rename variable LongRetryLimit to long_retry_limit, ShortRetryLimit to short_retry_limit and ReceiveConfig to receive_config to avoid CamelCase which is not accepted by checkpatch.

Signed-off-by Philipp Hortmann <[email protected]>
---
 .../staging/rtl8192e/rtl8192e/r8192E_dev.c    | 26 +++++++++----------
 drivers/staging/rtl8192e/rtl8192e/rtl_core.h  |  6 ++---
 2 files changed, 16 insertions(+), 16 deletions(-)
drivers/staging/rtl8192e/rtl8192e/r8192E_dev.c +13 -13
index 9cffe09e429c..b0f33fbffa42 100644
@@ -127,7 +127,7 @@ void rtl92e_set_reg(struct net_device *dev, u8 variable, u8 *val)
 
 		Type = val[0];
 		RegRCR = rtl92e_readl(dev, RCR);
-		priv->ReceiveConfig = RegRCR;
+		priv->receive_config = RegRCR;
 
 		if (Type)
 			RegRCR |= (RCR_CBSSID);

@@ -135,7 +135,7 @@ void rtl92e_set_reg(struct net_device *dev, u8 variable, u8 *val)
 			RegRCR &= (~RCR_CBSSID);
 
 		rtl92e_writel(dev, RCR, RegRCR);
-		priv->ReceiveConfig = RegRCR;
+		priv->receive_config = RegRCR;
 
 	}
 	break;

@@ -594,8 +594,8 @@ static void _rtl92e_hwconfig(struct net_device *dev)
 	rtl92e_writel(dev, RRSR, regRRSR);
 
 	rtl92e_writew(dev, RETRY_LIMIT,
-		      priv->ShortRetryLimit << RETRY_LIMIT_SHORT_SHIFT |
-		      priv->LongRetryLimit << RETRY_LIMIT_LONG_SHIFT);
+		      priv->short_retry_limit << RETRY_LIMIT_SHORT_SHIFT |
+		      priv->long_retry_limit << RETRY_LIMIT_LONG_SHIFT);
 }
 
 bool rtl92e_start_adapter(struct net_device *dev)

@@ -670,7 +670,7 @@ bool rtl92e_start_adapter(struct net_device *dev)
 				  (MXDMA2_NoLimit<<MXDMA2_TX_SHIFT)));
 	rtl92e_writel(dev, MAC0, ((u32 *)dev->dev_addr)[0]);
 	rtl92e_writew(dev, MAC4, ((u16 *)(dev->dev_addr + 4))[0]);
-	rtl92e_writel(dev, RCR, priv->ReceiveConfig);
+	rtl92e_writel(dev, RCR, priv->receive_config);
 
 	rtl92e_writel(dev, RQPN1, NUM_OF_PAGE_IN_FW_QUEUE_BK <<
 		      RSVD_FW_QUEUE_PAGE_BK_SHIFT |

@@ -860,9 +860,9 @@ void rtl92e_link_change(struct net_device *dev)
 			if (ieee->intel_promiscuous_md_info.promiscuous_on)
 				;
 			else
-				priv->ReceiveConfig = reg |= RCR_CBSSID;
+				priv->receive_config = reg |= RCR_CBSSID;
 		} else
-			priv->ReceiveConfig = reg &= ~RCR_CBSSID;
+			priv->receive_config = reg &= ~RCR_CBSSID;
 
 		rtl92e_writel(dev, RCR, reg);
 	}

@@ -874,12 +874,12 @@ void rtl92e_set_monitor_mode(struct net_device *dev, bool bAllowAllDA,
 	struct r8192_priv *priv = rtllib_priv(dev);
 
 	if (bAllowAllDA)
-		priv->ReceiveConfig |= RCR_AAP;
+		priv->receive_config |= RCR_AAP;
 	else
-		priv->ReceiveConfig &= ~RCR_AAP;
+		priv->receive_config &= ~RCR_AAP;
 
 	if (WriteIntoReg)
-		rtl92e_writel(dev, RCR, priv->ReceiveConfig);
+		rtl92e_writel(dev, RCR, priv->receive_config);
 }
 
 static u8 _rtl92e_rate_mgn_to_hw(u8 rate)

@@ -2010,10 +2010,10 @@ rtl92e_init_variables(struct net_device  *dev)
 
 	priv->rtllib->tx_headroom = sizeof(struct tx_fwinfo_8190pci);
 
-	priv->ShortRetryLimit = 0x30;
-	priv->LongRetryLimit = 0x30;
+	priv->short_retry_limit = 0x30;
+	priv->long_retry_limit = 0x30;
 
-	priv->ReceiveConfig = RCR_ADD3	|
+	priv->receive_config = RCR_ADD3	|
 		RCR_AMF | RCR_ADF |
 		RCR_AICV |
 		RCR_AB | RCR_AM | RCR_APM |
drivers/staging/rtl8192e/rtl8192e/rtl_core.h +3 -3
index d86577277844..8de726de57f4 100644
@@ -362,7 +362,7 @@ struct r8192_priv {
 
 	u64		LastRxDescTSF;
 
-	u32		ReceiveConfig;
+	u32 receive_config;
 	u8		retry_data;
 	u8		retry_rts;
 	u16		rts;

@@ -371,8 +371,8 @@ struct r8192_priv {
 	int		 txringcount;
 	atomic_t	tx_pending[0x10];
 
-	u16		ShortRetryLimit;
-	u16		LongRetryLimit;
+	u16 short_retry_limit;
+	u16 long_retry_limit;
 
 	bool		hw_radio_off;
 	bool		blinked_ingpio;
Signature · 1 line
2.39.0
author
#2 lore raw

PATCH 2/9 staging: rtl8192e: Rename LastRxDescTSF, LoopbackMode and pFirmware

In reply to Philipp Hortmann

Rename variable LastRxDescTSF to last_rx_desc_tsf, LoopbackMode to loopback_mode and pFirmware to fw_info to avoid CamelCase which is not accepted by checkpatch.

Signed-off-by Philipp Hortmann <[email protected]>
---
 drivers/staging/rtl8192e/rtl8192e/r8192E_dev.c     | 14 +++++++-------
 .../staging/rtl8192e/rtl8192e/r8192E_firmware.c    |  4 ++--
 drivers/staging/rtl8192e/rtl8192e/rtl_core.c       | 12 ++++++------
 drivers/staging/rtl8192e/rtl8192e/rtl_core.h       |  6 +++---
 4 files changed, 18 insertions(+), 18 deletions(-)
drivers/staging/rtl8192e/rtl8192e/r8192E_dev.c +7 -7
index b0f33fbffa42..a0678c6bac72 100644
@@ -619,16 +619,16 @@ bool rtl92e_start_adapter(struct net_device *dev)
 		rtl92e_writeb(dev, ANAPAR, 0x37);
 		mdelay(500);
 	}
-	priv->pFirmware->status = FW_STATUS_0_INIT;
+	priv->fw_info->status = FW_STATUS_0_INIT;
 
 	ulRegRead = rtl92e_readl(dev, CPU_GEN);
-	if (priv->pFirmware->status == FW_STATUS_0_INIT)
+	if (priv->fw_info->status == FW_STATUS_0_INIT)
 		ulRegRead |= CPU_GEN_SYSTEM_RESET;
-	else if (priv->pFirmware->status == FW_STATUS_5_READY)
+	else if (priv->fw_info->status == FW_STATUS_5_READY)
 		ulRegRead |= CPU_GEN_FIRMWARE_RESET;
 	else
 		netdev_err(dev, "%s(): undefined firmware state: %d.\n",
-			   __func__, priv->pFirmware->status);
+			   __func__, priv->fw_info->status);
 
 	rtl92e_writel(dev, CPU_GEN, ulRegRead);
 

@@ -647,13 +647,13 @@ bool rtl92e_start_adapter(struct net_device *dev)
 		return rtStatus;
 	}
 
-	priv->LoopbackMode = RTL819X_NO_LOOPBACK;
+	priv->loopback_mode = RTL819X_NO_LOOPBACK;
 	if (priv->rst_progress == RESET_TYPE_NORESET) {
 		ulRegRead = rtl92e_readl(dev, CPU_GEN);
-		if (priv->LoopbackMode == RTL819X_NO_LOOPBACK)
+		if (priv->loopback_mode == RTL819X_NO_LOOPBACK)
 			ulRegRead = (ulRegRead & CPU_GEN_NO_LOOPBACK_MSK) |
 				    CPU_GEN_NO_LOOPBACK_SET;
-		else if (priv->LoopbackMode == RTL819X_MAC_LOOPBACK)
+		else if (priv->loopback_mode == RTL819X_MAC_LOOPBACK)
 			ulRegRead |= CPU_CCK_LOOPBACK;
 		else
 			netdev_err(dev, "%s: Invalid loopback mode setting.\n",
drivers/staging/rtl8192e/rtl8192e/r8192E_firmware.c +2 -2
index 789d288d7503..b011ec8c8a41 100644
@@ -51,7 +51,7 @@ static bool _rtl92e_fw_check_ready(struct net_device *dev,
 				   u8 load_fw_status)
 {
 	struct r8192_priv *priv = rtllib_priv(dev);
-	struct rt_firmware *pfirmware = priv->pFirmware;
+	struct rt_firmware *pfirmware = priv->fw_info;
 	bool rt_status  = true;
 
 	switch (load_fw_status) {

@@ -134,7 +134,7 @@ bool rtl92e_init_fw(struct net_device *dev)
 	enum opt_rst_type rst_opt = OPT_SYSTEM_RESET;
 	enum firmware_init_step starting_state = FW_INIT_STEP0_BOOT;
 
-	struct rt_firmware *pfirmware = priv->pFirmware;
+	struct rt_firmware *pfirmware = priv->fw_info;
 
 	netdev_dbg(dev, " PlatformInitFirmware()==>\n");
drivers/staging/rtl8192e/rtl8192e/rtl_core.c +6 -6
index 8e1180b75d38..7a89381bae50 100644
@@ -891,8 +891,8 @@ static void _rtl92e_init_priv_variable(struct net_device *dev)
 
 	priv->card_type = PCI;
 
-	priv->pFirmware = vzalloc(sizeof(struct rt_firmware));
-	if (!priv->pFirmware)
+	priv->fw_info = vzalloc(sizeof(struct rt_firmware));
+	if (!priv->fw_info)
 		netdev_err(dev,
 			   "rtl8192e: Unable to allocate space for firmware\n");
 

@@ -1807,9 +1807,9 @@ void rtl92e_update_rx_pkt_timestamp(struct net_device *dev,
 	struct r8192_priv *priv = rtllib_priv(dev);
 
 	if (stats->bIsAMPDU && !stats->bFirstMPDU)
-		stats->mac_time = priv->LastRxDescTSF;
+		stats->mac_time = priv->last_rx_desc_tsf;
 	else
-		priv->LastRxDescTSF = stats->mac_time;
+		priv->last_rx_desc_tsf = stats->mac_time;
 }
 
 long rtl92e_translate_to_dbm(struct r8192_priv *priv, u8 signal_strength_index)

@@ -2386,8 +2386,8 @@ static void _rtl92e_pci_disconnect(struct pci_dev *pdev)
 		priv->polling_timer_on = 0;
 		_rtl92e_down(dev, true);
 		rtl92e_dm_deinit(dev);
-		vfree(priv->pFirmware);
-		priv->pFirmware = NULL;
+		vfree(priv->fw_info);
+		priv->fw_info = NULL;
 		_rtl92e_free_rx_ring(dev);
 		for (i = 0; i < MAX_TX_QUEUE_COUNT; i++)
 			_rtl92e_free_tx_ring(dev, i);
drivers/staging/rtl8192e/rtl8192e/rtl_core.h +3 -3
index 8de726de57f4..da10835a987e 100644
@@ -325,8 +325,8 @@ struct r8192_priv {
 	struct bb_reg_definition PHYRegDef[4];
 	struct rate_adaptive rate_adaptive;
 
-	struct rt_firmware			*pFirmware;
-	enum rtl819x_loopback LoopbackMode;
+	struct rt_firmware *fw_info;
+	enum rtl819x_loopback loopback_mode;
 
 	struct timer_list			watch_dog_timer;
 	struct timer_list			fsync_timer;

@@ -360,7 +360,7 @@ struct r8192_priv {
 	int		rxringcount;
 	u16		rxbuffersize;
 
-	u64		LastRxDescTSF;
+	u64 last_rx_desc_tsf;
 
 	u32 receive_config;
 	u8		retry_data;
Signature · 1 line
2.39.0
author
#3 lore raw

PATCH 3/9 staging: rtl8192e: Rename PHYRegDef, CurrentChannelBW and CustomerID

In reply to Philipp Hortmann

Rename variable PHYRegDef to phy_reg_def, CurrentChannelBW to current_chnl_bw and CustomerID to customer_id to avoid CamelCase which is not accepted by checkpatch.

Signed-off-by Philipp Hortmann <[email protected]>
---
 .../rtl8192e/rtl8192e/r8190P_rtl8256.c        |   4 +-
 .../staging/rtl8192e/rtl8192e/r8192E_dev.c    |  28 +--
 .../staging/rtl8192e/rtl8192e/r8192E_phy.c    | 188 +++++++++---------
 drivers/staging/rtl8192e/rtl8192e/rtl_core.h  |   6 +-
 drivers/staging/rtl8192e/rtl8192e/rtl_dm.c    |  36 ++--
 5 files changed, 131 insertions(+), 131 deletions(-)
drivers/staging/rtl8192e/rtl8192e/r8190P_rtl8256.c +2 -2
index 2c1a4392aeff..9ea281808128 100644
@@ -70,7 +70,7 @@ bool rtl92e_config_rf(struct net_device *dev)
 		if (!rtl92e_is_legal_rf_path(dev, eRFPath))
 			continue;
 
-		pPhyReg = &priv->PHYRegDef[eRFPath];
+		pPhyReg = &priv->phy_reg_def[eRFPath];
 
 		switch (eRFPath) {
 		case RF90_PATH_A:

@@ -151,7 +151,7 @@ void rtl92e_set_cck_tx_power(struct net_device *dev, u8 powerlevel)
 
 	TxAGC = powerlevel;
 	if (priv->dynamic_tx_low_pwr) {
-		if (priv->CustomerID == RT_CID_819x_Netcore)
+		if (priv->customer_id == RT_CID_819x_Netcore)
 			TxAGC = 0x22;
 		else
 			TxAGC += priv->cck_pwr_enl;
drivers/staging/rtl8192e/rtl8192e/r8192E_dev.c +14 -14
index a0678c6bac72..fe985f4b8dbb 100644
@@ -478,36 +478,36 @@ static void _rtl92e_read_eeprom_info(struct net_device *dev)
 		priv->chnl_plan = priv->reg_chnl_plan;
 
 	if (priv->eeprom_vid == 0x1186 &&  priv->eeprom_did == 0x3304)
-		priv->CustomerID =  RT_CID_DLINK;
+		priv->customer_id =  RT_CID_DLINK;
 
 	switch (priv->eeprom_CustomerID) {
 	case EEPROM_CID_DEFAULT:
-		priv->CustomerID = RT_CID_DEFAULT;
+		priv->customer_id = RT_CID_DEFAULT;
 		break;
 	case EEPROM_CID_CAMEO:
-		priv->CustomerID = RT_CID_819x_CAMEO;
+		priv->customer_id = RT_CID_819x_CAMEO;
 		break;
 	case  EEPROM_CID_RUNTOP:
-		priv->CustomerID = RT_CID_819x_RUNTOP;
+		priv->customer_id = RT_CID_819x_RUNTOP;
 		break;
 	case EEPROM_CID_NetCore:
-		priv->CustomerID = RT_CID_819x_Netcore;
+		priv->customer_id = RT_CID_819x_Netcore;
 		break;
 	case EEPROM_CID_TOSHIBA:
-		priv->CustomerID = RT_CID_TOSHIBA;
+		priv->customer_id = RT_CID_TOSHIBA;
 		if (priv->eeprom_chnl_plan & 0x80)
 			priv->chnl_plan = priv->eeprom_chnl_plan & 0x7f;
 		else
 			priv->chnl_plan = 0x0;
 		break;
 	case EEPROM_CID_Nettronix:
-		priv->CustomerID = RT_CID_Nettronix;
+		priv->customer_id = RT_CID_Nettronix;
 		break;
 	case EEPROM_CID_Pronet:
-		priv->CustomerID = RT_CID_PRONET;
+		priv->customer_id = RT_CID_PRONET;
 		break;
 	case EEPROM_CID_DLINK:
-		priv->CustomerID = RT_CID_DLINK;
+		priv->customer_id = RT_CID_DLINK;
 		break;
 
 	case EEPROM_CID_WHQL:

@@ -1068,7 +1068,7 @@ void  rtl92e_fill_tx_desc(struct net_device *dev, struct tx_desc *pdesc,
 	pTxFwInfo->RtsShort = (pTxFwInfo->RtsHT == 0) ?
 			  (cb_desc->bRTSUseShortPreamble ? 1 : 0) :
 			  (cb_desc->bRTSUseShortGI ? 1 : 0);
-	if (priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20_40) {
+	if (priv->current_chnl_bw == HT_CHANNEL_WIDTH_20_40) {
 		if (cb_desc->bPacketBW) {
 			pTxFwInfo->TxBandwidth = 1;
 			pTxFwInfo->TxSubCarrier = 0;

@@ -2101,16 +2101,16 @@ bool rtl92e_is_rx_stuck(struct net_device *dev)
 	if (priv->undecorated_smoothed_pwdb >= (RateAdaptiveTH_High+5)) {
 		rx_chk_cnt = 0;
 	} else if ((priv->undecorated_smoothed_pwdb < (RateAdaptiveTH_High + 5))
-	  && (((priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20) &&
+	  && (((priv->current_chnl_bw != HT_CHANNEL_WIDTH_20) &&
 	  (priv->undecorated_smoothed_pwdb >= RateAdaptiveTH_Low_40M))
-	  || ((priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20) &&
+	  || ((priv->current_chnl_bw == HT_CHANNEL_WIDTH_20) &&
 	  (priv->undecorated_smoothed_pwdb >= RateAdaptiveTH_Low_20M)))) {
 		if (rx_chk_cnt < 2)
 			return bStuck;
 		rx_chk_cnt = 0;
-	} else if ((((priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20) &&
+	} else if ((((priv->current_chnl_bw != HT_CHANNEL_WIDTH_20) &&
 		  (priv->undecorated_smoothed_pwdb < RateAdaptiveTH_Low_40M)) ||
-		((priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20) &&
+		((priv->current_chnl_bw == HT_CHANNEL_WIDTH_20) &&
 		 (priv->undecorated_smoothed_pwdb < RateAdaptiveTH_Low_20M))) &&
 		priv->undecorated_smoothed_pwdb >= VeryLowRSSI) {
 		if (rx_chk_cnt < 4)
drivers/staging/rtl8192e/rtl8192e/r8192E_phy.c +94 -94

251 lines not on this page · raw message

drivers/staging/rtl8192e/rtl8192e/rtl_core.h +3 -3
index da10835a987e..cbafbecb5ca5 100644
@@ -317,12 +317,12 @@ struct r8192_priv {
 
 	struct work_struct				reset_wq;
 
-	enum rt_customer_id CustomerID;
+	enum rt_customer_id customer_id;
 
 
 	enum rt_rf_type_819xu rf_chip;
-	enum ht_channel_width CurrentChannelBW;
-	struct bb_reg_definition PHYRegDef[4];
+	enum ht_channel_width current_chnl_bw;
+	struct bb_reg_definition phy_reg_def[4];
 	struct rate_adaptive rate_adaptive;
 
 	struct rt_firmware *fw_info;
drivers/staging/rtl8192e/rtl8192e/rtl_dm.c +18 -18
index 63be5f2872c6..cb55b6645674 100644
@@ -292,7 +292,7 @@ void rtl92e_init_adaptive_rate(struct net_device *dev)
 	pra->low_rssi_thresh_for_ra20M = RateAdaptiveTH_Low_20M;
 	pra->low_rssi_thresh_for_ra40M = RateAdaptiveTH_Low_40M;
 
-	if (priv->CustomerID == RT_CID_819x_Netcore)
+	if (priv->customer_id == RT_CID_819x_Netcore)
 		pra->ping_rssi_enable = 1;
 	else
 		pra->ping_rssi_enable = 0;

@@ -353,7 +353,7 @@ static void _rtl92e_dm_check_rate_adaptive(struct net_device *dev)
 				(pra->middle_rssi_threshold_ratr & (~BIT31)) |
 				((bshort_gi_enabled) ? BIT31 : 0);
 
-		if (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20) {
+		if (priv->current_chnl_bw != HT_CHANNEL_WIDTH_20) {
 			pra->low_rssi_threshold_ratr =
 				(pra->low_rssi_threshold_ratr_40M & (~BIT31)) |
 				((bshort_gi_enabled) ? BIT31 : 0);

@@ -368,15 +368,15 @@ static void _rtl92e_dm_check_rate_adaptive(struct net_device *dev)
 
 		if (pra->ratr_state == DM_RATR_STA_HIGH) {
 			HighRSSIThreshForRA = pra->high2low_rssi_thresh_for_ra;
-			LowRSSIThreshForRA = (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20) ?
+			LowRSSIThreshForRA = (priv->current_chnl_bw != HT_CHANNEL_WIDTH_20) ?
 					(pra->low_rssi_thresh_for_ra40M) : (pra->low_rssi_thresh_for_ra20M);
 		} else if (pra->ratr_state == DM_RATR_STA_LOW) {
 			HighRSSIThreshForRA = pra->high_rssi_thresh_for_ra;
-			LowRSSIThreshForRA = (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20) ?
+			LowRSSIThreshForRA = (priv->current_chnl_bw != HT_CHANNEL_WIDTH_20) ?
 					(pra->low2high_rssi_thresh_for_ra40M) : (pra->low2high_rssi_thresh_for_ra20M);
 		} else {
 			HighRSSIThreshForRA = pra->high_rssi_thresh_for_ra;
-			LowRSSIThreshForRA = (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20) ?
+			LowRSSIThreshForRA = (priv->current_chnl_bw != HT_CHANNEL_WIDTH_20) ?
 					(pra->low_rssi_thresh_for_ra40M) : (pra->low_rssi_thresh_for_ra20M);
 		}
 

@@ -443,8 +443,8 @@ static void _rtl92e_dm_bandwidth_autoswitch(struct net_device *dev)
 {
 	struct r8192_priv *priv = rtllib_priv(dev);
 
-	if (priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20 ||
-	   !priv->rtllib->bandwidth_auto_switch.bautoswitch_enable)
+	if (priv->current_chnl_bw == HT_CHANNEL_WIDTH_20 ||
+	    !priv->rtllib->bandwidth_auto_switch.bautoswitch_enable)
 		return;
 	if (!priv->rtllib->bandwidth_auto_switch.bforced_tx20Mhz) {
 		if (priv->undecorated_smoothed_pwdb <=

@@ -715,7 +715,7 @@ static void _rtl92e_dm_tx_power_tracking_callback_tssi(struct net_device *dev)
 					= priv->rfa_txpowertrackingindex_real - priv->rfa_txpowertracking_default;
 			}
 
-			if (priv->CurrentChannelBW == HT_CHANNEL_WIDTH_20)
+			if (priv->current_chnl_bw == HT_CHANNEL_WIDTH_20)
 				priv->cck_present_attn =
 					 priv->cck_present_attn_20m_def +
 					 priv->cck_present_attn_diff;

@@ -818,7 +818,7 @@ static void _rtl92e_dm_tx_power_tracking_cb_thermal(struct net_device *dev)
 		}
 		tmpCCK40Mindex = 0;
 	}
-	if (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20)
+	if (priv->current_chnl_bw != HT_CHANNEL_WIDTH_20)
 		tmpCCKindex = tmpCCK40Mindex;
 	else
 		tmpCCKindex = tmpCCK20Mindex;

@@ -1150,7 +1150,7 @@ static void _rtl92e_dm_dig_init(struct net_device *dev)
 	dm_digtable.rssi_val = 50;
 	dm_digtable.backoff_val = DM_DIG_BACKOFF;
 	dm_digtable.rx_gain_range_max = DM_DIG_MAX;
-	if (priv->CustomerID == RT_CID_819x_Netcore)
+	if (priv->customer_id == RT_CID_819x_Netcore)
 		dm_digtable.rx_gain_range_min = DM_DIG_MIN_Netcore;
 	else
 		dm_digtable.rx_gain_range_min = DM_DIG_MIN;

@@ -1260,7 +1260,7 @@ static void _rtl92e_dm_ctrl_initgain_byrssi_false_alarm(struct net_device *dev)
 		rtl92e_writeb(dev, rOFDM0_XCAGCCore1, 0x17);
 		rtl92e_writeb(dev, rOFDM0_XDAGCCore1, 0x17);
 
-		if (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20)
+		if (priv->current_chnl_bw != HT_CHANNEL_WIDTH_20)
 			rtl92e_writeb(dev, (rOFDM0_XATxAFE+3), 0x00);
 		else
 			rtl92e_writeb(dev, rOFDM0_RxDetector1, 0x42);

@@ -1297,7 +1297,7 @@ static void _rtl92e_dm_ctrl_initgain_byrssi_false_alarm(struct net_device *dev)
 			rtl92e_writeb(dev, rOFDM0_XDAGCCore1, 0x20);
 		}
 
-		if (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20)
+		if (priv->current_chnl_bw != HT_CHANNEL_WIDTH_20)
 			rtl92e_writeb(dev, (rOFDM0_XATxAFE+3), 0x20);
 		else
 			rtl92e_writeb(dev, rOFDM0_RxDetector1, 0x44);

@@ -1328,7 +1328,7 @@ static void _rtl92e_dm_ctrl_initgain_byrssi_highpwr(struct net_device *dev)
 			return;
 		dm_digtable.dig_highpwr_state = DM_STA_DIG_ON;
 
-		if (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20)
+		if (priv->current_chnl_bw != HT_CHANNEL_WIDTH_20)
 			rtl92e_writeb(dev, (rOFDM0_XATxAFE+3), 0x10);
 		else
 			rtl92e_writeb(dev, rOFDM0_RxDetector1, 0x43);

@@ -1342,7 +1342,7 @@ static void _rtl92e_dm_ctrl_initgain_byrssi_highpwr(struct net_device *dev)
 		     dm_digtable.rssi_high_power_lowthresh) &&
 		    (priv->undecorated_smoothed_pwdb >=
 		    dm_digtable.rssi_high_thresh)) {
-			if (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20)
+			if (priv->current_chnl_bw != HT_CHANNEL_WIDTH_20)
 				rtl92e_writeb(dev, (rOFDM0_XATxAFE+3), 0x20);
 			else
 				rtl92e_writeb(dev, rOFDM0_RxDetector1, 0x44);

@@ -1453,18 +1453,18 @@ static void _rtl92e_dm_pd_th(struct net_device *dev)
 	if ((dm_digtable.prepd_thstate != dm_digtable.curpd_thstate) ||
 	    (initialized <= 3) || force_write) {
 		if (dm_digtable.curpd_thstate == DIG_PD_AT_LOW_POWER) {
-			if (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20)
+			if (priv->current_chnl_bw != HT_CHANNEL_WIDTH_20)
 				rtl92e_writeb(dev, (rOFDM0_XATxAFE+3), 0x00);
 			else
 				rtl92e_writeb(dev, rOFDM0_RxDetector1, 0x42);
 		} else if (dm_digtable.curpd_thstate ==
 			   DIG_PD_AT_NORMAL_POWER) {
-			if (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20)
+			if (priv->current_chnl_bw != HT_CHANNEL_WIDTH_20)
 				rtl92e_writeb(dev, (rOFDM0_XATxAFE+3), 0x20);
 			else
 				rtl92e_writeb(dev, rOFDM0_RxDetector1, 0x44);
 		} else if (dm_digtable.curpd_thstate == DIG_PD_AT_HIGH_POWER) {
-			if (priv->CurrentChannelBW != HT_CHANNEL_WIDTH_20)
+			if (priv->current_chnl_bw != HT_CHANNEL_WIDTH_20)
 				rtl92e_writeb(dev, (rOFDM0_XATxAFE+3), 0x10);
 			else
 				rtl92e_writeb(dev, rOFDM0_RxDetector1, 0x43);

@@ -1736,7 +1736,7 @@ static void _rtl92e_dm_init_rx_path_selection(struct net_device *dev)
 	DM_RxPathSelTable.Enable = 1;
 	DM_RxPathSelTable.SS_TH_low = RxPathSelection_SS_TH_low;
 	DM_RxPathSelTable.diff_TH = RxPathSelection_diff_TH;
-	if (priv->CustomerID == RT_CID_819x_Netcore)
+	if (priv->customer_id == RT_CID_819x_Netcore)
 		DM_RxPathSelTable.cck_method = CCK_Rx_Version_2;
 	else
 		DM_RxPathSelTable.cck_method = CCK_Rx_Version_1;
Signature · 1 line
2.39.0
author
#4 lore raw

PATCH 4/9 staging: rtl8192e: Remove unused variable SifsTime

In reply to Philipp Hortmann

SifsTime is written and then never evaluated. Remove resulting dead code.

Signed-off-by Philipp Hortmann <[email protected]>
---
 drivers/staging/rtl8192e/rtl8192e/r8192E_phy.c | 1 -
 drivers/staging/rtl8192e/rtl8192e/rtl_core.h   | 1 -
 2 files changed, 2 deletions(-)
drivers/staging/rtl8192e/rtl8192e/r8192E_phy.c +0 -1
index f7865d0c787a..ed27bdbb8fb9 100644
@@ -581,7 +581,6 @@ void rtl92e_get_tx_power(struct net_device *dev)
 
 	priv->framesync = rtl92e_readb(dev, rOFDM0_RxDetector3);
 	priv->framesyncC34 = rtl92e_readl(dev, rOFDM0_RxDetector2);
-	priv->SifsTime = rtl92e_readw(dev, SIFS);
 }
 
 void rtl92e_set_tx_power(struct net_device *dev, u8 channel)
drivers/staging/rtl8192e/rtl8192e/rtl_core.h +0 -1
index cbafbecb5ca5..feb48ee35110 100644
@@ -412,7 +412,6 @@ struct r8192_priv {
 	u8 short_preamble;
 	u8 dot11_current_preamble_mode;
 	u8 slot_time;
-	u16 SifsTime;
 
 	bool autoload_fail_flag;
Signature · 1 line
2.39.0
author
#5 lore raw

PATCH 5/9 staging: rtl8192e: Remove unused variable framesyncC34

In reply to Philipp Hortmann

framesyncC34 is written and then never evaluated. Remove resulting dead code.

Signed-off-by Philipp Hortmann <[email protected]>
---
 drivers/staging/rtl8192e/rtl8192e/r8192E_phy.c | 1 -
 drivers/staging/rtl8192e/rtl8192e/rtl_core.h   | 1 -
 2 files changed, 2 deletions(-)
drivers/staging/rtl8192e/rtl8192e/r8192E_phy.c +0 -1
index ed27bdbb8fb9..aafe39e50bd9 100644
@@ -580,7 +580,6 @@ void rtl92e_get_tx_power(struct net_device *dev)
 	priv->def_initial_gain[3] = rtl92e_readb(dev, rOFDM0_XDAGCCore1);
 
 	priv->framesync = rtl92e_readb(dev, rOFDM0_RxDetector3);
-	priv->framesyncC34 = rtl92e_readl(dev, rOFDM0_RxDetector2);
 }
 
 void rtl92e_set_tx_power(struct net_device *dev, u8 channel)
drivers/staging/rtl8192e/rtl8192e/rtl_core.h +0 -1
index feb48ee35110..626a2bc48969 100644
@@ -513,7 +513,6 @@ struct r8192_priv {
 	u32		continue_diff_count;
 	bool		bswitch_fsync;
 	u8		framesync;
-	u32		framesyncC34;
 	u8		frame_sync_monitor;
 
 	u32		reset_count;
Signature · 1 line
2.39.0
author
#7 lore raw

PATCH 7/9 staging: rtl8192e: Remove unused variable H2CTxCmdSeq

In reply to Philipp Hortmann

H2CTxCmdSeq is never used. Remove resulting dead code.

Signed-off-by Philipp Hortmann <[email protected]>
---
 drivers/staging/rtl8192e/rtl8192e/rtl_core.h | 2 --
 1 file changed, 2 deletions(-)
drivers/staging/rtl8192e/rtl8192e/rtl_core.h +0 -2
index e90cc61b3817..12a869a556bb 100644
@@ -525,8 +525,6 @@ struct r8192_priv {
 	bool		force_lps;
 
 	bool		chan_forced;
-
-	u8		H2CTxCmdSeq;
 };
 
 extern const struct ethtool_ops rtl819x_ethtool_ops;
Signature · 1 line
2.39.0
author
#6 lore raw

PATCH 6/9 staging: rtl8192e: Remove unused variable PwrDomainProtect

In reply to Philipp Hortmann

PwrDomainProtect is initialized and then never evaluated. Remove resulting dead code.

Signed-off-by Philipp Hortmann <[email protected]>
---
 drivers/staging/rtl8192e/rtl8192e/r8192E_dev.c | 2 --
 drivers/staging/rtl8192e/rtl8192e/rtl_core.h   | 1 -
 2 files changed, 3 deletions(-)
drivers/staging/rtl8192e/rtl8192e/r8192E_dev.c +0 -2
index fe985f4b8dbb..227c13d552fc 100644
@@ -2027,8 +2027,6 @@ rtl92e_init_variables(struct net_device  *dev)
 			    IMR_RDU | IMR_RXFOVW | IMR_TXFOVW |
 			    IMR_BcnInt | IMR_TBDOK | IMR_TBDER);
 
-	priv->PwrDomainProtect = false;
-
 	priv->bfirst_after_down = false;
 }
drivers/staging/rtl8192e/rtl8192e/rtl_core.h +0 -1
index 626a2bc48969..e90cc61b3817 100644
@@ -526,7 +526,6 @@ struct r8192_priv {
 
 	bool		chan_forced;
 
-	u8		PwrDomainProtect;
 	u8		H2CTxCmdSeq;
 };
Signature · 1 line
2.39.0
author
#8 lore raw

PATCH 8/9 staging: rtl8192e: Remove unused variable RF_C_TxPwDiff

In reply to Philipp Hortmann

RF_C_TxPwDiff is set to a value and then never evaluated. Remove resulting dead code.

Signed-off-by Philipp Hortmann <[email protected]>
---
 drivers/staging/rtl8192e/rtl8192e/r8192E_phy.c | 2 --
 drivers/staging/rtl8192e/rtl8192e/rtl_core.h   | 1 -
 2 files changed, 3 deletions(-)
drivers/staging/rtl8192e/rtl8192e/r8192E_phy.c +0 -2
index aafe39e50bd9..ff66a97b8763 100644
@@ -603,8 +603,6 @@ void rtl92e_set_tx_power(struct net_device *dev, u8 channel)
 			ant_pwr_diff = priv->tx_pwr_level_ofdm_24g_c[channel - 1]
 				       - priv->tx_pwr_level_ofdm_24g_a[channel - 1];
 
-			priv->RF_C_TxPwDiff = ant_pwr_diff;
-
 			ant_pwr_diff &= 0xf;
 
 			priv->antenna_tx_pwr_diff[2] = 0;
drivers/staging/rtl8192e/rtl8192e/rtl_core.h +0 -1
index 12a869a556bb..6662558e56fa 100644
@@ -476,7 +476,6 @@ struct r8192_priv {
 	u8 tx_pwr_level_ofdm_24g_a[14];
 	u8 tx_pwr_level_ofdm_24g_c[14];
 	u8 legacy_ht_tx_pwr_diff;
-	s8		RF_C_TxPwDiff;
 	u8 antenna_tx_pwr_diff[3];
 
 	bool		dynamic_tx_high_pwr;
Signature · 1 line
2.39.0
author
#9 lore raw

PATCH 9/9 staging: rtl8192e: Remove unused variable DM_Type

In reply to Philipp Hortmann

DM_Type is initialized and then never evaluated. Remove resulting dead code.

Signed-off-by Philipp Hortmann <[email protected]>
---
 drivers/staging/rtl8192e/rtl8192e/rtl_core.h | 2 --
 drivers/staging/rtl8192e/rtl8192e/rtl_dm.c   | 2 --
 drivers/staging/rtl8192e/rtl8192e/rtl_dm.h   | 2 --
 3 files changed, 6 deletions(-)
drivers/staging/rtl8192e/rtl8192e/rtl_core.h +0 -2
index 6662558e56fa..11f3f88491b2 100644
@@ -457,8 +457,6 @@ struct r8192_priv {
 	bool set_rf_pwr_state_in_progress;
 	bool bdisable_nic;
 
-	u8 DM_Type;
-
 	u8 cck_pwr_enl;
 	u16 tssi_13dBm;
 	u32 pwr_track;
drivers/staging/rtl8192e/rtl8192e/rtl_dm.c +0 -2
index cb55b6645674..ba92dab682ec 100644
@@ -203,8 +203,6 @@ void rtl92e_dm_init(struct net_device *dev)
 {
 	struct r8192_priv *priv = rtllib_priv(dev);
 
-	priv->DM_Type = DM_Type_ByDriver;
-
 	priv->undecorated_smoothed_pwdb = -1;
 
 	_rtl92e_dm_init_dynamic_tx_power(dev);
drivers/staging/rtl8192e/rtl8192e/rtl_dm.h +0 -2
index 1d4d7d98a859..65d077dfee37 100644
@@ -47,8 +47,6 @@
 #define		TX_RETRY_COUNT_REG		0x1ac
 #define		RegC38_TH				 20
 
-#define		DM_Type_ByDriver		1
-
 /*--------------------------Define Parameters-------------------------------*/
Signature · 1 line
2.39.0