Skip to contentSkip to conversation

net: ethernet: mtk_eth_soc: various enhancements

PATCH Superseded Daniel Golle 2 participants 14 messages Feb 15, 2023

Subsystems (10)

v7 of 14 Superseded Latest is v14 →

lore
Share & tools
lore

Daniel Golle

author maintainer
#0 lore raw

v7 cover net: ethernet: mtk_eth_soc: various enhancements

This series brings a variety of fixes and enhancements for mtk_eth_soc, adds support for the MT7981 SoC and facilitates sharing the SGMII PCS code between mtk_eth_soc and mt7530.

Note that this series depends on commit 697c3892d825 ("regmap: apply reg_base and reg_downshift for single register ops") to not break mt7530 pcs register access.

The whole series has been tested on MT7622+MT7531 (BPi-R64), MT7623+MT7530 (BPi-R2) and MT7981+GPY211 (GL.iNet GL-MT3000).

Changes since v6:
* label MAC MCR bit 12 in 08/12, MediaTek replied explaining its function
* move mediatek,sgmiisys bindings to Documentation/devicetree/bindings/clock

Changes since v5:
* drop dev pointer also from struct mtk_sgmii, pass it as function paramter instead
* address comments left for dt-bindings
* minor improvements to commit messages

Changes since v4:
* remove unused dev pointer in struct pcs_mtk_lynxi
* squash link timer check into correct follow-up patch

Changes since v3:
* remove unused #define's
* use BMCR_* instead of #define'ing our own constants
* return before changing registers in case of invalid link timer

Changes since v2:
* improve dt-bindings, convert sgmisys bindings to dt-schema yaml
* fix typo

Changes since v1:
* apply reverse xmas tree everywhere
* improve commit descriptions
* add dt binding documentation
* various small changes addressing all comments received for v1

Daniel Golle (12):
net: ethernet: mtk_eth_soc: add support for MT7981 SoC
dt-bindings: net: mediatek,net: add mt7981-eth binding
dt-bindings: arm: mediatek: sgmiisys: Convert to DT schema
dt-bindings: arm: mediatek: sgmiisys: add MT7981 SoC
net: ethernet: mtk_eth_soc: set MDIO bus clock frequency
net: ethernet: mtk_eth_soc: reset PCS state
net: ethernet: mtk_eth_soc: only write values if needed
net: ethernet: mtk_eth_soc: fix RX data corruption issue
net: ethernet: mtk_eth_soc: ppe: add support for flow accounting
net: pcs: add driver for MediaTek SGMII PCS
net: ethernet: mtk_eth_soc: switch to external PCS driver
net: dsa: mt7530: use external PCS driver

 .../arm/mediatek/mediatek,sgmiisys.txt        |  27 --
 .../bindings/clock/mediatek,sgmiisys.yaml     |  55 ++++
 .../devicetree/bindings/net/mediatek,net.yaml |  52 ++-
 MAINTAINERS                                   |   7 +
 drivers/net/dsa/Kconfig                       |   1 +
 drivers/net/dsa/mt7530.c                      | 277 ++++------------
 drivers/net/dsa/mt7530.h                      |  47 +--
 drivers/net/ethernet/mediatek/Kconfig         |   2 +
 drivers/net/ethernet/mediatek/mtk_eth_path.c  |  14 +-
 drivers/net/ethernet/mediatek/mtk_eth_soc.c   |  67 +++-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h   | 105 +++---
 drivers/net/ethernet/mediatek/mtk_ppe.c       | 114 ++++++-
 drivers/net/ethernet/mediatek/mtk_ppe.h       |  25 +-
 .../net/ethernet/mediatek/mtk_ppe_debugfs.c   |   9 +-
 .../net/ethernet/mediatek/mtk_ppe_offload.c   |   8 +
 drivers/net/ethernet/mediatek/mtk_ppe_regs.h  |  14 +
 drivers/net/ethernet/mediatek/mtk_sgmii.c     | 192 ++---------
 drivers/net/pcs/Kconfig                       |   7 +
 drivers/net/pcs/Makefile                      |   1 +
 drivers/net/pcs/pcs-mtk-lynxi.c               | 303 ++++++++++++++++++
 include/linux/pcs/pcs-mtk-lynxi.h             |  13 +
 21 files changed, 802 insertions(+), 538 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,sgmiisys.txt
 create mode 100644 Documentation/devicetree/bindings/clock/mediatek,sgmiisys.yaml
 create mode 100644 drivers/net/pcs/pcs-mtk-lynxi.c
 create mode 100644 include/linux/pcs/pcs-mtk-lynxi.h

base-commit: 9d9019bcea1aac7eed64a1a4966282b6b7b141c8

Signature · 1 line
2.39.1
author maintainer
#1 lore raw

PATCH v7 1/12 net: ethernet: mtk_eth_soc: add support for MT7981 SoC

The MediaTek MT7981 SoC comes with two 1G/2.5G SGMII ports, just like MT7986.

In addition MT7981 is equipped with a built-in 1000Base-T PHY which can be used with GMAC1.

As many MT7981 boards make use of inverting SGMII signal polarity, add new device-tree attribute 'mediatek,pn_swap' to support them.

---
 drivers/net/ethernet/mediatek/mtk_eth_path.c | 14 +++++++--
 drivers/net/ethernet/mediatek/mtk_eth_soc.c  | 21 +++++++++++++
 drivers/net/ethernet/mediatek/mtk_eth_soc.h  | 31 ++++++++++++++++++++
 drivers/net/ethernet/mediatek/mtk_sgmii.c    | 10 +++++++
 4 files changed, 73 insertions(+), 3 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_path.c +11 -3
index 72648535a14d..317e447f4991 100644
@@ -96,12 +96,20 @@ static int set_mux_gmac2_gmac0_to_gephy(struct mtk_eth *eth, int path)
 
 static int set_mux_u3_gmac2_to_qphy(struct mtk_eth *eth, int path)
 {
-	unsigned int val = 0;
+	unsigned int val = 0, mask = 0, reg = 0;
 	bool updated = true;
 
 	switch (path) {
 	case MTK_ETH_PATH_GMAC2_SGMII:
-		val = CO_QPHY_SEL;
+		if (MTK_HAS_CAPS(eth->soc->caps, MTK_U3_COPHY_V2)) {
+			reg = USB_PHY_SWITCH_REG;
+			val = SGMII_QPHY_SEL;
+			mask = QPHY_SEL_MASK;
+		} else {
+			reg = INFRA_MISC2;
+			val = CO_QPHY_SEL;
+			mask = val;
+		}
 		break;
 	default:
 		updated = false;
@@ -109,7 +117,7 @@ static int set_mux_u3_gmac2_to_qphy(struct mtk_eth *eth, int path)
 	}
 
 	if (updated)
-		regmap_update_bits(eth->infra, INFRA_MISC2, CO_QPHY_SEL, val);
+		regmap_update_bits(eth->infra, reg, mask, val);
 
 	dev_dbg(eth->dev, "path %s in %s updated = %d\n",
 		mtk_eth_path_name(path), __func__, updated);
drivers/net/ethernet/mediatek/mtk_eth_soc.c +21 -0
index 14be6ea51b88..cfb15a84b894 100644
@@ -4860,6 +4860,26 @@ static const struct mtk_soc_data mt7629_data = {
 	},
 };
 
+static const struct mtk_soc_data mt7981_data = {
+	.reg_map = &mt7986_reg_map,
+	.ana_rgc3 = 0x128,
+	.caps = MT7981_CAPS,
+	.hw_features = MTK_HW_FEATURES,
+	.required_clks = MT7981_CLKS_BITMAP,
+	.required_pctl = false,
+	.offload_version = 2,
+	.hash_offset = 4,
+	.foe_entry_size = sizeof(struct mtk_foe_entry),
+	.txrx = {
+		.txd_size = sizeof(struct mtk_tx_dma_v2),
+		.rxd_size = sizeof(struct mtk_rx_dma_v2),
+		.rx_irq_done_mask = MTK_RX_DONE_INT_V2,
+		.rx_dma_l4_valid = RX_DMA_L4_VALID_V2,
+		.dma_max_len = MTK_TX_DMA_BUF_LEN_V2,
+		.dma_len_offset = 8,
+	},
+};
+
 static const struct mtk_soc_data mt7986_data = {
 	.reg_map = &mt7986_reg_map,
 	.ana_rgc3 = 0x128,
@@ -4902,6 +4922,7 @@ const struct of_device_id of_mtk_match[] = {
 	{ .compatible = "mediatek,mt7622-eth", .data = &mt7622_data},
 	{ .compatible = "mediatek,mt7623-eth", .data = &mt7623_data},
 	{ .compatible = "mediatek,mt7629-eth", .data = &mt7629_data},
+	{ .compatible = "mediatek,mt7981-eth", .data = &mt7981_data},
 	{ .compatible = "mediatek,mt7986-eth", .data = &mt7986_data},
 	{ .compatible = "ralink,rt5350-eth", .data = &rt5350_data},
 	{},
drivers/net/ethernet/mediatek/mtk_eth_soc.h +31 -0
index afc9d52e79bf..7230dcb29315 100644
@@ -551,11 +551,22 @@
 #define SGMSYS_QPHY_PWR_STATE_CTRL 0xe8
 #define	SGMII_PHYA_PWD		BIT(4)
 
+/* Register to QPHY wrapper control */
+#define SGMSYS_QPHY_WRAP_CTRL	0xec
+#define SGMII_PN_SWAP_MASK	GENMASK(1, 0)
+#define SGMII_PN_SWAP_TX_RX	(BIT(0) | BIT(1))
+#define MTK_SGMII_FLAG_PN_SWAP	BIT(0)
+
 /* Infrasys subsystem config registers */
 #define INFRA_MISC2            0x70c
 #define CO_QPHY_SEL            BIT(0)
 #define GEPHY_MAC_SEL          BIT(1)
 
+/* Top misc registers */
+#define USB_PHY_SWITCH_REG	0x218
+#define QPHY_SEL_MASK		GENMASK(1, 0)
+#define SGMII_QPHY_SEL		0x2
+
 /* MT7628/88 specific stuff */
 #define MT7628_PDMA_OFFSET	0x0800
 #define MT7628_SDM_OFFSET	0x0c00
@@ -736,6 +747,17 @@ enum mtk_clks_map {
 				 BIT(MTK_CLK_SGMII2_CDR_FB) | \
 				 BIT(MTK_CLK_SGMII_CK) | \
 				 BIT(MTK_CLK_ETH2PLL) | BIT(MTK_CLK_SGMIITOP))
+#define MT7981_CLKS_BITMAP	(BIT(MTK_CLK_FE) | BIT(MTK_CLK_GP2) | BIT(MTK_CLK_GP1) | \
+				 BIT(MTK_CLK_WOCPU0) | \
+				 BIT(MTK_CLK_SGMII_TX_250M) | \
+				 BIT(MTK_CLK_SGMII_RX_250M) | \
+				 BIT(MTK_CLK_SGMII_CDR_REF) | \
+				 BIT(MTK_CLK_SGMII_CDR_FB) | \
+				 BIT(MTK_CLK_SGMII2_TX_250M) | \
+				 BIT(MTK_CLK_SGMII2_RX_250M) | \
+				 BIT(MTK_CLK_SGMII2_CDR_REF) | \
+				 BIT(MTK_CLK_SGMII2_CDR_FB) | \
+				 BIT(MTK_CLK_SGMII_CK))
 #define MT7986_CLKS_BITMAP	(BIT(MTK_CLK_FE) | BIT(MTK_CLK_GP2) | BIT(MTK_CLK_GP1) | \
 				 BIT(MTK_CLK_WOCPU1) | BIT(MTK_CLK_WOCPU0) | \
 				 BIT(MTK_CLK_SGMII_TX_250M) | \
@@ -849,6 +871,7 @@ enum mkt_eth_capabilities {
 	MTK_NETSYS_V2_BIT,
 	MTK_SOC_MT7628_BIT,
 	MTK_RSTCTRL_PPE1_BIT,
+	MTK_U3_COPHY_V2_BIT,
 
 	/* MUX BITS*/
 	MTK_ETH_MUX_GDM1_TO_GMAC1_ESW_BIT,
@@ -883,6 +906,7 @@ enum mkt_eth_capabilities {
 #define MTK_NETSYS_V2		BIT(MTK_NETSYS_V2_BIT)
 #define MTK_SOC_MT7628		BIT(MTK_SOC_MT7628_BIT)
 #define MTK_RSTCTRL_PPE1	BIT(MTK_RSTCTRL_PPE1_BIT)
+#define MTK_U3_COPHY_V2		BIT(MTK_U3_COPHY_V2_BIT)
 
 #define MTK_ETH_MUX_GDM1_TO_GMAC1_ESW		\
 	BIT(MTK_ETH_MUX_GDM1_TO_GMAC1_ESW_BIT)
@@ -955,6 +979,11 @@ enum mkt_eth_capabilities {
 		      MTK_MUX_U3_GMAC2_TO_QPHY | \
 		      MTK_MUX_GMAC12_TO_GEPHY_SGMII | MTK_QDMA)
 
+#define MT7981_CAPS  (MTK_GMAC1_SGMII | MTK_GMAC2_SGMII | MTK_GMAC2_GEPHY | \
+		      MTK_MUX_GMAC12_TO_GEPHY_SGMII | MTK_QDMA | \
+		      MTK_MUX_U3_GMAC2_TO_QPHY | MTK_U3_COPHY_V2 | \
+		      MTK_NETSYS_V2 | MTK_RSTCTRL_PPE1)
+
 #define MT7986_CAPS  (MTK_GMAC1_SGMII | MTK_GMAC2_SGMII | \
 		      MTK_MUX_GMAC12_TO_GEPHY_SGMII | MTK_QDMA | \
 		      MTK_NETSYS_V2 | MTK_RSTCTRL_PPE1)
@@ -1068,12 +1097,14 @@ struct mtk_soc_data {
  * @ana_rgc3:          The offset refers to register ANA_RGC3 related to regmap
  * @interface:         Currently configured interface mode
  * @pcs:               Phylink PCS structure
+ * @flags:             Flags indicating hardware properties
  */
 struct mtk_pcs {
 	struct regmap	*regmap;
 	u32             ana_rgc3;
 	phy_interface_t	interface;
 	struct phylink_pcs pcs;
+	u32		flags;
 };
 
 /* struct mtk_sgmii -  This is the structure holding sgmii regmap and its
drivers/net/ethernet/mediatek/mtk_sgmii.c +10 -0
index bb00de1003ac..d7ffaaeaf9ab 100644
@@ -88,6 +88,11 @@ static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
 		regmap_update_bits(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL,
 				   SGMII_PHYA_PWD, SGMII_PHYA_PWD);
 
+		if (mpcs->flags & MTK_SGMII_FLAG_PN_SWAP)
+			regmap_update_bits(mpcs->regmap, SGMSYS_QPHY_WRAP_CTRL,
+					   SGMII_PN_SWAP_MASK,
+					   SGMII_PN_SWAP_TX_RX);
+
 		if (interface == PHY_INTERFACE_MODE_2500BASEX)
 			rgc3 = RG_PHY_SPEED_3_125G;
 		else
@@ -182,6 +187,11 @@ int mtk_sgmii_init(struct mtk_sgmii *ss, struct device_node *r, u32 ana_rgc3)
 
 		ss->pcs[i].ana_rgc3 = ana_rgc3;
 		ss->pcs[i].regmap = syscon_node_to_regmap(np);
+
+		ss->pcs[i].flags = 0;
+		if (of_property_read_bool(np, "mediatek,pnswap"))
+			ss->pcs[i].flags |= MTK_SGMII_FLAG_PN_SWAP;
+
 		of_node_put(np);
 		if (IS_ERR(ss->pcs[i].regmap))
 			return PTR_ERR(ss->pcs[i].regmap);
Signature · 1 line
2.39.1
author maintainer
#2 lore raw

PATCH v7 2/12 dt-bindings: net: mediatek,net: add mt7981-eth binding

In reply to Daniel Golle

Introduce DT bindings for the MT7981 SoC to mediatek,net.yaml.

---
 .../devicetree/bindings/net/mediatek,net.yaml | 52 +++++++++++++++++--
 1 file changed, 47 insertions(+), 5 deletions(-)
Documentation/devicetree/bindings/net/mediatek,net.yaml +47 -5
index 7ef696204c5a..925ab2982d54 100644
@@ -21,6 +21,7 @@ properties:
       - mediatek,mt7623-eth
       - mediatek,mt7622-eth
       - mediatek,mt7629-eth
+      - mediatek,mt7981-eth
       - mediatek,mt7986-eth
       - ralink,rt5350-eth
 
@@ -78,6 +79,11 @@ properties:
     description:
       List of phandles to wireless ethernet dispatch nodes.
 
+  mediatek,wed-pcie:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      Phandle to the mediatek wed-pcie controller.
+
   dma-coherent: true
 
   mdio-bus:
@@ -123,6 +129,8 @@ allOf:
 
         mediatek,wed: false
 
+        mediatek,wed-pci: false
+
   - if:
       properties:
         compatible:
@@ -206,6 +214,45 @@ allOf:
 
         mediatek,wed: false
 
+        mediatek,wed-pci: false
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: mediatek,mt7981-eth
+    then:
+      properties:
+        interrupts:
+          minItems: 4
+
+        clocks:
+          minItems: 15
+          maxItems: 15
+
+        clock-names:
+          items:
+            - const: fe
+            - const: gp2
+            - const: gp1
+            - const: wocpu0
+            - const: sgmii_ck
+            - const: sgmii_tx250m
+            - const: sgmii_rx250m
+            - const: sgmii_cdr_ref
+            - const: sgmii_cdr_fb
+            - const: sgmii2_tx250m
+            - const: sgmii2_rx250m
+            - const: sgmii2_cdr_ref
+            - const: sgmii2_cdr_fb
+            - const: netsys0
+            - const: netsys1
+
+        mediatek,sgmiisys:
+          minItems: 2
+          maxItems: 2
+
+
   - if:
       properties:
         compatible:
@@ -242,11 +289,6 @@ allOf:
           minItems: 2
           maxItems: 2
 
-        mediatek,wed-pcie:
-          $ref: /schemas/types.yaml#/definitions/phandle
-          description:
-            Phandle to the mediatek wed-pcie controller.
-
 patternProperties:
   "^mac@[0-1]$":
     type: object
Signature · 1 line
2.39.1
author maintainer
#3 lore raw

PATCH v7 3/12 dt-bindings: arm: mediatek: sgmiisys: Convert to DT schema

In reply to Daniel Golle

Convert mediatek,sgmiiisys bindings to DT schema format. Add maintainer Matthias Brugger, no maintainers were listed in the original documentation.
As this node is also referenced by the Ethernet controller and used as SGMII PCS add this fact to the description.

---
 .../arm/mediatek/mediatek,sgmiisys.txt        | 27 ----------
 .../bindings/clock/mediatek,sgmiisys.yaml     | 49 +++++++++++++++++++
 2 files changed, 49 insertions(+), 27 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,sgmiisys.txt
 create mode 100644 Documentation/devicetree/bindings/clock/mediatek,sgmiisys.yaml
Documentation/devicetree/bindings/arm/mediatek/mediatek,sgmiisys.txt deleted +0 -27
deleted file mode 100644
index d2c24c277514..000000000000
@@ -1,27 +0,0 @@
-MediaTek SGMIISYS controller
-============================
-
-The MediaTek SGMIISYS controller provides various clocks to the system.
-
-Required Properties:
-
-- compatible: Should be:
-	- "mediatek,mt7622-sgmiisys", "syscon"
-	- "mediatek,mt7629-sgmiisys", "syscon"
-	- "mediatek,mt7981-sgmiisys_0", "syscon"
-	- "mediatek,mt7981-sgmiisys_1", "syscon"
-	- "mediatek,mt7986-sgmiisys_0", "syscon"
-	- "mediatek,mt7986-sgmiisys_1", "syscon"
-- #clock-cells: Must be 1
-
-The SGMIISYS controller uses the common clk binding from
-Documentation/devicetree/bindings/clock/clock-bindings.txt
-The available clocks are defined in dt-bindings/clock/mt*-clk.h.
-
-Example:
-
-sgmiisys: sgmiisys@1b128000 {
-	compatible = "mediatek,mt7622-sgmiisys", "syscon";
-	reg = <0 0x1b128000 0 0x1000>;
-	#clock-cells = <1>;
-};
Documentation/devicetree/bindings/clock/mediatek,sgmiisys.yaml new file +49 -0

49 lines not on this page · raw message

Signature · 1 line
2.39.1
author maintainer
#4 lore raw

PATCH v7 4/12 dt-bindings: arm: mediatek: sgmiisys: add MT7981 SoC

In reply to Daniel Golle

Add mediatek,pnswap boolean property needed on many boards using the MediaTek MT7981 SoC.

---
 .../devicetree/bindings/clock/mediatek,sgmiisys.yaml | 6 ++++++
 1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/clock/mediatek,sgmiisys.yaml +6 -0
index 6bb84fe23de4..43721ec119d9 100644
@@ -19,6 +19,8 @@ properties:
       - enum:
           - mediatek,mt7622-sgmiisys
           - mediatek,mt7629-sgmiisys
+          - mediatek,mt7981-sgmiisys_0
+          - mediatek,mt7981-sgmiisys_1
           - mediatek,mt7986-sgmiisys_0
           - mediatek,mt7986-sgmiisys_1
       - const: syscon
@@ -29,6 +31,10 @@ properties:
   '#clock-cells':
     const: 1
 
+  mediatek,pnswap:
+    description: Invert polarity of the SGMII data lanes
+    type: boolean
+
 required:
   - compatible
   - reg
Signature · 1 line
2.39.1
author maintainer
#5 lore raw

PATCH v7 5/12 net: ethernet: mtk_eth_soc: set MDIO bus clock frequency

In reply to Daniel Golle

Set MDIO bus clock frequency and allow setting a custom maximum frequency from device tree.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 21 +++++++++++++++++++++
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |  7 +++++++
 2 files changed, 28 insertions(+)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +21 -0
index cfb15a84b894..030d87c42bd4 100644
@@ -789,8 +789,10 @@ static const struct phylink_mac_ops mtk_phylink_ops = {
 
 static int mtk_mdio_init(struct mtk_eth *eth)
 {
+	unsigned int max_clk = 2500000, divider;
 	struct device_node *mii_np;
 	int ret;
+	u32 val;
 
 	mii_np = of_get_child_by_name(eth->dev->of_node, "mdio-bus");
 	if (!mii_np) {
@@ -818,6 +820,25 @@ static int mtk_mdio_init(struct mtk_eth *eth)
 	eth->mii_bus->parent = eth->dev;
 
 	snprintf(eth->mii_bus->id, MII_BUS_ID_SIZE, "%pOFn", mii_np);
+
+	if (!of_property_read_u32(mii_np, "clock-frequency", &val)) {
+		if (val > MDC_MAX_FREQ || val < MDC_MAX_FREQ / MDC_MAX_DIVIDER) {
+			dev_err(eth->dev, "MDIO clock frequency out of range");
+			ret = -EINVAL;
+			goto err_put_node;
+		}
+		max_clk = val;
+	}
+	divider = min_t(unsigned int, DIV_ROUND_UP(MDC_MAX_FREQ, max_clk), 63);
+
+	/* Configure MDC Divider */
+	val = mtk_r32(eth, MTK_PPSC);
+	val &= ~PPSC_MDC_CFG;
+	val |= FIELD_PREP(PPSC_MDC_CFG, divider) | PPSC_MDC_TURBO;
+	mtk_w32(eth, val, MTK_PPSC);
+
+	dev_dbg(eth->dev, "MDC is running on %d Hz\n", MDC_MAX_FREQ / divider);
+
 	ret = of_mdiobus_register(eth->mii_bus, mii_np);
 
 err_put_node:
drivers/net/ethernet/mediatek/mtk_eth_soc.h +7 -0
index 7230dcb29315..7014c02ba2d4 100644
@@ -363,6 +363,13 @@
 #define RX_DMA_VTAG_V2		BIT(0)
 #define RX_DMA_L4_VALID_V2	BIT(2)
 
+/* PHY Polling and SMI Master Control registers */
+#define MTK_PPSC		0x10000
+#define PPSC_MDC_CFG		GENMASK(29, 24)
+#define PPSC_MDC_TURBO		BIT(20)
+#define MDC_MAX_FREQ		25000000
+#define MDC_MAX_DIVIDER		63
+
 /* PHY Indirect Access Control registers */
 #define MTK_PHY_IAC		0x10004
 #define PHY_IAC_ACCESS		BIT(31)
Signature · 1 line
2.39.1
author maintainer
#6 lore raw

PATCH v7 6/12 net: ethernet: mtk_eth_soc: reset PCS state

In reply to Daniel Golle

Reset PCS state when changing interface mode.

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 4 ++++
 drivers/net/ethernet/mediatek/mtk_sgmii.c   | 4 ++++
 2 files changed, 8 insertions(+)
drivers/net/ethernet/mediatek/mtk_eth_soc.h +4 -0
index 7014c02ba2d4..142def8629c8 100644
@@ -548,6 +548,10 @@
 #define SGMII_SEND_AN_ERROR_EN		BIT(11)
 #define SGMII_IF_MODE_MASK		GENMASK(5, 1)
 
+/* Register to reset SGMII design */
+#define SGMII_RESERVED_0	0x34
+#define SGMII_SW_RESET		BIT(0)
+
 /* Register to set SGMII speed, ANA RG_ Control Signals III*/
 #define SGMSYS_ANA_RG_CS3	0x2028
 #define RG_PHY_SPEED_MASK	(BIT(2) | BIT(3))
drivers/net/ethernet/mediatek/mtk_sgmii.c +4 -0
index d7ffaaeaf9ab..d7e7352041a4 100644
@@ -88,6 +88,10 @@ static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
 		regmap_update_bits(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL,
 				   SGMII_PHYA_PWD, SGMII_PHYA_PWD);
 
+		/* Reset SGMII PCS state */
+		regmap_update_bits(mpcs->regmap, SGMII_RESERVED_0,
+				   SGMII_SW_RESET, SGMII_SW_RESET);
+
 		if (mpcs->flags & MTK_SGMII_FLAG_PN_SWAP)
 			regmap_update_bits(mpcs->regmap, SGMSYS_QPHY_WRAP_CTRL,
 					   SGMII_PN_SWAP_MASK,
Signature · 1 line
2.39.1
author maintainer
#7 lore raw

PATCH v7 7/12 net: ethernet: mtk_eth_soc: only write values if needed

In reply to Daniel Golle

Only restart auto-negotiation and write link timer if actually necessary.

---
 drivers/net/ethernet/mediatek/mtk_sgmii.c | 24 +++++++++++------------
 1 file changed, 12 insertions(+), 12 deletions(-)
drivers/net/ethernet/mediatek/mtk_sgmii.c +12 -12
index d7e7352041a4..61bd9986466a 100644
@@ -38,20 +38,16 @@ static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
 			  const unsigned long *advertising,
 			  bool permit_pause_to_mac)
 {
+	bool mode_changed = false, changed, use_an;
 	struct mtk_pcs *mpcs = pcs_to_mtk_pcs(pcs);
 	unsigned int rgc3, sgm_mode, bmcr;
 	int advertise, link_timer;
-	bool changed, use_an;
 
 	advertise = phylink_mii_c22_pcs_encode_advertisement(interface,
 							     advertising);
 	if (advertise < 0)
 		return advertise;
 
-	link_timer = phylink_get_link_timer_ns(interface);
-	if (link_timer < 0)
-		return link_timer;
-
 	/* Clearing IF_MODE_BIT0 switches the PCS to BASE-X mode, and
 	 * we assume that fixes it's speed at bitrate = line rate (in
 	 * other words, 1000Mbps or 2500Mbps).
@@ -77,13 +73,16 @@ static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
 	}
 
 	if (use_an) {
-		/* FIXME: Do we need to set AN_RESTART here? */
-		bmcr = SGMII_AN_RESTART | SGMII_AN_ENABLE;
+		bmcr = SGMII_AN_ENABLE;
 	} else {
 		bmcr = 0;
 	}
 
 	if (mpcs->interface != interface) {
+		link_timer = phylink_get_link_timer_ns(interface);
+		if (link_timer < 0)
+			return link_timer;
+
 		/* PHYA power down */
 		regmap_update_bits(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL,
 				   SGMII_PHYA_PWD, SGMII_PHYA_PWD);
@@ -106,16 +105,17 @@ static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
 		regmap_update_bits(mpcs->regmap, mpcs->ana_rgc3,
 				   RG_PHY_SPEED_3_125G, rgc3);
 
+		/* Setup the link timer */
+		regmap_write(mpcs->regmap, SGMSYS_PCS_LINK_TIMER, link_timer / 2 / 8);
+
 		mpcs->interface = interface;
+		mode_changed = true;
 	}
 
 	/* Update the advertisement, noting whether it has changed */
 	regmap_update_bits_check(mpcs->regmap, SGMSYS_PCS_ADVERTISE,
 				 SGMII_ADVERTISE, advertise, &changed);
 
-	/* Setup the link timer and QPHY power up inside SGMIISYS */
-	regmap_write(mpcs->regmap, SGMSYS_PCS_LINK_TIMER, link_timer / 2 / 8);
-
 	/* Update the sgmsys mode register */
 	regmap_update_bits(mpcs->regmap, SGMSYS_SGMII_MODE,
 			   SGMII_REMOTE_FAULT_DIS | SGMII_SPEED_DUPLEX_AN |
@@ -123,7 +123,7 @@ static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
 
 	/* Update the BMCR */
 	regmap_update_bits(mpcs->regmap, SGMSYS_PCS_CONTROL_1,
-			   SGMII_AN_RESTART | SGMII_AN_ENABLE, bmcr);
+			   SGMII_AN_ENABLE, bmcr);
 
 	/* Release PHYA power down state
 	 * Only removing bit SGMII_PHYA_PWD isn't enough.
@@ -137,7 +137,7 @@ static int mtk_pcs_config(struct phylink_pcs *pcs, unsigned int mode,
 	usleep_range(50, 100);
 	regmap_write(mpcs->regmap, SGMSYS_QPHY_PWR_STATE_CTRL, 0);
 
-	return changed;
+	return changed || mode_changed;
 }
 
 static void mtk_pcs_restart_an(struct phylink_pcs *pcs)
Signature · 1 line
2.39.1
author maintainer
#8 lore raw

PATCH v7 8/12 net: ethernet: mtk_eth_soc: fix RX data corruption issue

In reply to Daniel Golle

Also set bit 12 which disabled the RX FIDO clear function when setting up MAC MCR, as MediaTek SDK did the same change stating:
"If without this patch, kernel might receive invalid packets that are corrupted by GMAC."[1]
This fixes issues with <= 1G speed where we could previously observe about 30% packet loss while the bad packet counter was increasing.

[1]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/d8a2975939a12686c4a95c40db21efdc3f821f63

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 3 ++-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 1 +
 2 files changed, 3 insertions(+), 1 deletion(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +2 -1
index 030d87c42bd4..ed32a511adc3 100644
@@ -616,7 +616,8 @@ static int mtk_mac_finish(struct phylink_config *config, unsigned int mode,
 	mcr_cur = mtk_r32(mac->hw, MTK_MAC_MCR(mac->id));
 	mcr_new = mcr_cur;
 	mcr_new |= MAC_MCR_IPG_CFG | MAC_MCR_FORCE_MODE |
-		   MAC_MCR_BACKOFF_EN | MAC_MCR_BACKPR_EN | MAC_MCR_FORCE_LINK;
+		   MAC_MCR_BACKOFF_EN | MAC_MCR_BACKPR_EN | MAC_MCR_FORCE_LINK |
+		   MAC_MCR_RX_FIFO_CLR_DIS;
 
 	/* Only update control register when needed! */
 	if (mcr_new != mcr_cur)
drivers/net/ethernet/mediatek/mtk_eth_soc.h +1 -0
index 142def8629c8..529c95c481b7 100644
@@ -404,6 +404,7 @@
 #define MAC_MCR_FORCE_MODE	BIT(15)
 #define MAC_MCR_TX_EN		BIT(14)
 #define MAC_MCR_RX_EN		BIT(13)
+#define MAC_MCR_RX_FIFO_CLR_DIS	BIT(12)
 #define MAC_MCR_BACKOFF_EN	BIT(9)
 #define MAC_MCR_BACKPR_EN	BIT(8)
 #define MAC_MCR_FORCE_RX_FC	BIT(5)
Signature · 1 line
2.39.1
author maintainer
#9 lore raw

PATCH v7 9/12 net: ethernet: mtk_eth_soc: ppe: add support for flow accounting

In reply to Daniel Golle

The PPE units found in MT7622 and newer support packet and byte accounting of hw-offloaded flows. Add support for reading those counters as found in MediaTek's SDK[1].

[1]: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/bc6a6a375c800dc2b80e1a325a2c732d1737df92

---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c   |   8 +-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h   |   1 +
 drivers/net/ethernet/mediatek/mtk_ppe.c       | 114 +++++++++++++++++-
 drivers/net/ethernet/mediatek/mtk_ppe.h       |  25 +++-
 .../net/ethernet/mediatek/mtk_ppe_debugfs.c   |   9 +-
 .../net/ethernet/mediatek/mtk_ppe_offload.c   |   8 ++
 drivers/net/ethernet/mediatek/mtk_ppe_regs.h  |  14 +++
 7 files changed, 170 insertions(+), 9 deletions(-)
drivers/net/ethernet/mediatek/mtk_eth_soc.c +6 -2
index ed32a511adc3..677a39cbde08 100644
@@ -4712,8 +4712,8 @@ static int mtk_probe(struct platform_device *pdev)
 		for (i = 0; i < num_ppe; i++) {
 			u32 ppe_addr = eth->soc->reg_map->ppe_base + i * 0x400;
 
-			eth->ppe[i] = mtk_ppe_init(eth, eth->base + ppe_addr,
-						   eth->soc->offload_version, i);
+			eth->ppe[i] = mtk_ppe_init(eth, eth->base + ppe_addr, i);
+
 			if (!eth->ppe[i]) {
 				err = -ENOMEM;
 				goto err_deinit_ppe;
@@ -4835,6 +4835,7 @@ static const struct mtk_soc_data mt7622_data = {
 	.required_pctl = false,
 	.offload_version = 2,
 	.hash_offset = 2,
+	.has_accounting = true,
 	.foe_entry_size = sizeof(struct mtk_foe_entry) - 16,
 	.txrx = {
 		.txd_size = sizeof(struct mtk_tx_dma),
@@ -4872,6 +4873,7 @@ static const struct mtk_soc_data mt7629_data = {
 	.hw_features = MTK_HW_FEATURES,
 	.required_clks = MT7629_CLKS_BITMAP,
 	.required_pctl = false,
+	.has_accounting = true,
 	.txrx = {
 		.txd_size = sizeof(struct mtk_tx_dma),
 		.rxd_size = sizeof(struct mtk_rx_dma),
@@ -4892,6 +4894,7 @@ static const struct mtk_soc_data mt7981_data = {
 	.offload_version = 2,
 	.hash_offset = 4,
 	.foe_entry_size = sizeof(struct mtk_foe_entry),
+	.has_accounting = true,
 	.txrx = {
 		.txd_size = sizeof(struct mtk_tx_dma_v2),
 		.rxd_size = sizeof(struct mtk_rx_dma_v2),
@@ -4912,6 +4915,7 @@ static const struct mtk_soc_data mt7986_data = {
 	.offload_version = 2,
 	.hash_offset = 4,
 	.foe_entry_size = sizeof(struct mtk_foe_entry),
+	.has_accounting = true,
 	.txrx = {
 		.txd_size = sizeof(struct mtk_tx_dma_v2),
 		.rxd_size = sizeof(struct mtk_rx_dma_v2),
drivers/net/ethernet/mediatek/mtk_eth_soc.h +1 -0
index 529c95c481b7..f90d61bfa3c1 100644
@@ -1087,6 +1087,7 @@ struct mtk_soc_data {
 	u8		hash_offset;
 	u16		foe_entry_size;
 	netdev_features_t hw_features;
+	bool		has_accounting;
 	struct {
 		u32	txd_size;
 		u32	rxd_size;
drivers/net/ethernet/mediatek/mtk_ppe.c +111 -3

159 lines not on this page · raw message

drivers/net/ethernet/mediatek/mtk_ppe.h +23 -2
index 5e8bc48252b1..e1aab2e8e262 100644
@@ -57,6 +57,7 @@ enum {
 #define MTK_FOE_IB2_MULTICAST		BIT(8)
 
 #define MTK_FOE_IB2_WDMA_QID2		GENMASK(13, 12)
+#define MTK_FOE_IB2_MIB_CNT		BIT(15)
 #define MTK_FOE_IB2_WDMA_DEVIDX		BIT(16)
 #define MTK_FOE_IB2_WDMA_WINFO		BIT(17)
 
@@ -285,16 +286,34 @@ struct mtk_flow_entry {
 	unsigned long cookie;
 };
 
+struct mtk_mib_entry {
+	u32	byt_cnt_l;
+	u16	byt_cnt_h;
+	u32	pkt_cnt_l;
+	u8	pkt_cnt_h;
+	u8	_rsv0;
+	u32	_rsv1;
+} __packed;
+
+struct mtk_foe_accounting {
+	u64	bytes;
+	u64	packets;
+};
+
 struct mtk_ppe {
 	struct mtk_eth *eth;
 	struct device *dev;
 	void __iomem *base;
 	int version;
 	char dirname[5];
+	bool accounting;
 
 	void *foe_table;
 	dma_addr_t foe_phys;
 
+	struct mtk_mib_entry *mib_table;
+	dma_addr_t mib_phys;
+
 	u16 foe_check_time[MTK_PPE_ENTRIES];
 	struct hlist_head *foe_flow;
 
@@ -303,8 +322,8 @@ struct mtk_ppe {
 	void *acct_table;
 };
 
-struct mtk_ppe *mtk_ppe_init(struct mtk_eth *eth, void __iomem *base,
-			     int version, int index);
+struct mtk_ppe *mtk_ppe_init(struct mtk_eth *eth, void __iomem *base, int index);
+
 void mtk_ppe_deinit(struct mtk_eth *eth);
 void mtk_ppe_start(struct mtk_ppe *ppe);
 int mtk_ppe_stop(struct mtk_ppe *ppe);
@@ -359,5 +378,7 @@ int mtk_foe_entry_commit(struct mtk_ppe *ppe, struct mtk_flow_entry *entry);
 void mtk_foe_entry_clear(struct mtk_ppe *ppe, struct mtk_flow_entry *entry);
 int mtk_foe_entry_idle_time(struct mtk_ppe *ppe, struct mtk_flow_entry *entry);
 int mtk_ppe_debugfs_init(struct mtk_ppe *ppe, int index);
+struct mtk_foe_accounting *mtk_foe_entry_get_mib(struct mtk_ppe *ppe, u32 index,
+						 struct mtk_foe_accounting *diff);
 
 #endif
drivers/net/ethernet/mediatek/mtk_ppe_debugfs.c +7 -2
index 391b071bcff3..53cf87e9acbb 100644
@@ -82,6 +82,7 @@ mtk_ppe_debugfs_foe_show(struct seq_file *m, void *private, bool bind)
 		struct mtk_foe_entry *entry = mtk_foe_get_entry(ppe, i);
 		struct mtk_foe_mac_info *l2;
 		struct mtk_flow_addr_info ai = {};
+		struct mtk_foe_accounting *acct;
 		unsigned char h_source[ETH_ALEN];
 		unsigned char h_dest[ETH_ALEN];
 		int type, state;
@@ -95,6 +96,8 @@ mtk_ppe_debugfs_foe_show(struct seq_file *m, void *private, bool bind)
 		if (bind && state != MTK_FOE_STATE_BIND)
 			continue;
 
+		acct = mtk_foe_entry_get_mib(ppe, i, NULL);
+
 		type = FIELD_GET(MTK_FOE_IB1_PACKET_TYPE, entry->ib1);
 		seq_printf(m, "%05x %s %7s", i,
 			   mtk_foe_entry_state_str(state),
@@ -153,9 +156,11 @@ mtk_ppe_debugfs_foe_show(struct seq_file *m, void *private, bool bind)
 		*((__be16 *)&h_dest[4]) = htons(l2->dest_mac_lo);
 
 		seq_printf(m, " eth=%pM->%pM etype=%04x"
-			      " vlan=%d,%d ib1=%08x ib2=%08x\n",
+			      " vlan=%d,%d ib1=%08x ib2=%08x"
+			      " packets=%llu bytes=%llu\n",
 			   h_source, h_dest, ntohs(l2->etype),
-			   l2->vlan1, l2->vlan2, entry->ib1, ib2);
+			   l2->vlan1, l2->vlan2, entry->ib1, ib2,
+			   acct ? acct->packets : 0, acct ? acct->bytes : 0);
 	}
 
 	return 0;
drivers/net/ethernet/mediatek/mtk_ppe_offload.c +8 -0
index 81afd5ee3fbf..f02ccffb1e79 100644
@@ -497,6 +497,7 @@ static int
 mtk_flow_offload_stats(struct mtk_eth *eth, struct flow_cls_offload *f)
 {
 	struct mtk_flow_entry *entry;
+	struct mtk_foe_accounting diff;
 	u32 idle;
 
 	entry = rhashtable_lookup(&eth->flow_table, &f->cookie,
@@ -507,6 +508,13 @@ mtk_flow_offload_stats(struct mtk_eth *eth, struct flow_cls_offload *f)
 	idle = mtk_foe_entry_idle_time(eth->ppe[entry->ppe_index], entry);
 	f->stats.lastused = jiffies - idle * HZ;
 
+	if (entry->hash != 0xFFFF &&
+	    mtk_foe_entry_get_mib(eth->ppe[entry->ppe_index], entry->hash,
+				  &diff)) {
+		f->stats.pkts += diff.packets;
+		f->stats.bytes += diff.bytes;
+	}
+
 	return 0;
 }
 
drivers/net/ethernet/mediatek/mtk_ppe_regs.h +14 -0
index 0fdb983b0a88..a2e61b3eb006 100644
@@ -149,6 +149,20 @@ enum {
 
 #define MTK_PPE_MIB_TB_BASE			0x338
 
+#define MTK_PPE_MIB_SER_CR			0x33C
+#define MTK_PPE_MIB_SER_CR_ST			BIT(16)
+#define MTK_PPE_MIB_SER_CR_ADDR			GENMASK(13, 0)
+
+#define MTK_PPE_MIB_SER_R0			0x340
+#define MTK_PPE_MIB_SER_R0_BYTE_CNT_LOW		GENMASK(31, 0)
+
+#define MTK_PPE_MIB_SER_R1			0x344
+#define MTK_PPE_MIB_SER_R1_PKT_CNT_LOW		GENMASK(31, 16)
+#define MTK_PPE_MIB_SER_R1_BYTE_CNT_HIGH	GENMASK(15, 0)
+
+#define MTK_PPE_MIB_SER_R2			0x348
+#define MTK_PPE_MIB_SER_R2_PKT_CNT_HIGH		GENMASK(23, 0)
+
 #define MTK_PPE_MIB_CACHE_CTL			0x350
 #define MTK_PPE_MIB_CACHE_CTL_EN		BIT(0)
 #define MTK_PPE_MIB_CACHE_CTL_FLUSH		BIT(2)
Signature · 1 line
2.39.1
author maintainer
#10 lore raw

PATCH v7 10/12 net: pcs: add driver for MediaTek SGMII PCS

In reply to Daniel Golle

The SGMII core found in several MediaTek SoCs is identical to what can also be found in MediaTek's MT7531 Ethernet switch IC.
As this has not always been clear, both drivers developed different implementations to deal with the PCS.

Add a dedicated driver, mostly by copying the code now found in the Ethernet driver. The now redundant code will be removed by a follow-up commit.

---
 MAINTAINERS                       |   7 +
 drivers/net/pcs/Kconfig           |   7 +
 drivers/net/pcs/Makefile          |   1 +
 drivers/net/pcs/pcs-mtk-lynxi.c   | 303 ++++++++++++++++++++++++++++++
 include/linux/pcs/pcs-mtk-lynxi.h |  13 ++
 5 files changed, 331 insertions(+)
 create mode 100644 drivers/net/pcs/pcs-mtk-lynxi.c
 create mode 100644 include/linux/pcs/pcs-mtk-lynxi.h
MAINTAINERS +7 -0
index be167c695c64..bdfc5543d70c 100644
@@ -13038,6 +13038,13 @@ L:	[email protected]
 S:	Maintained
 F:	drivers/net/ethernet/mediatek/
 
+MEDIATEK ETHERNET PCS DRIVER
+M:	Daniel Golle <[email protected]>
+L:	[email protected]
+S:	Maintained
+F:	drivers/net/pcs/pcs-mtk-lynxi.c
+F:	include/linux/pcs/pcs-mtk-lynxi.h
+
 MEDIATEK I2C CONTROLLER DRIVER
 M:	Qii Wang <[email protected]>
 L:	[email protected]
drivers/net/pcs/Kconfig +7 -0
index 6e7e6c346a3e..7c34fb7cbf7b 100644
@@ -18,6 +18,13 @@ config PCS_LYNX
 	  This module provides helpers to phylink for managing the Lynx PCS
 	  which is part of the Layerscape and QorIQ Ethernet SERDES.
 
+config PCS_MTK_LYNXI
+	tristate
+	select REGMAP
+	help
+	  This module provides helpers to phylink for managing the LynxI PCS
+	  which is part of MediaTek's SoC and Ethernet switch ICs.
+
 config PCS_RZN1_MIIC
 	tristate "Renesas RZ/N1 MII converter"
 	depends on OF && (ARCH_RZN1 || COMPILE_TEST)
drivers/net/pcs/Makefile +1 -0
index 4c780d8f2e98..9b9afd6b1c22 100644
@@ -5,5 +5,6 @@ pcs_xpcs-$(CONFIG_PCS_XPCS)	:= pcs-xpcs.o pcs-xpcs-nxp.o
 
 obj-$(CONFIG_PCS_XPCS)		+= pcs_xpcs.o
 obj-$(CONFIG_PCS_LYNX)		+= pcs-lynx.o
+obj-$(CONFIG_PCS_MTK_LYNXI)	+= pcs-mtk-lynxi.o
 obj-$(CONFIG_PCS_RZN1_MIIC)	+= pcs-rzn1-miic.o
 obj-$(CONFIG_PCS_ALTERA_TSE)	+= pcs-altera-tse.o
drivers/net/pcs/pcs-mtk-lynxi.c new file +303 -0

303 lines not on this page · raw message

include/linux/pcs/pcs-mtk-lynxi.h new file +13 -0
new file mode 100644
index 000000000000..be3b4ab32f4a
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __LINUX_PCS_MTK_LYNXI_H
+#define __LINUX_PCS_MTK_LYNXI_H
+
+#include <linux/phylink.h>
+#include <linux/regmap.h>
+
+#define MTK_SGMII_FLAG_PN_SWAP BIT(0)
+struct phylink_pcs *mtk_pcs_lynxi_create(struct device *dev,
+					 struct regmap *regmap,
+					 u32 ana_rgc3, u32 flags);
+void mtk_pcs_lynxi_destroy(struct phylink_pcs *pcs);
+#endif
Signature · 1 line
2.39.1
author maintainer
#11 lore raw

PATCH v7 11/12 net: ethernet: mtk_eth_soc: switch to external PCS driver

In reply to Daniel Golle

Now that we got a PCS driver, use it and remove the now redundant PCS code and it's header macros from the Ethernet driver.

---
 drivers/net/ethernet/mediatek/Kconfig       |   2 +
 drivers/net/ethernet/mediatek/mtk_eth_soc.c |  14 +-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |  85 +-------
 drivers/net/ethernet/mediatek/mtk_sgmii.c   | 202 +++-----------------
 4 files changed, 40 insertions(+), 263 deletions(-)
drivers/net/ethernet/mediatek/Kconfig +2 -0
index 97374fb3ee79..da0db417ab69 100644
@@ -19,6 +19,8 @@ config NET_MEDIATEK_SOC
 	select DIMLIB
 	select PAGE_POOL
 	select PAGE_POOL_STATS
+	select PCS_MTK_LYNXI
+	select REGMAP_MMIO
 	help
 	  This driver supports the gigabit ethernet MACs in the
 	  MediaTek SoC family.
drivers/net/ethernet/mediatek/mtk_eth_soc.c +10 -4
index 677a39cbde08..e9327ffd6f5e 100644
@@ -4080,6 +4080,7 @@ static int mtk_unreg_dev(struct mtk_eth *eth)
 
 static int mtk_cleanup(struct mtk_eth *eth)
 {
+	mtk_sgmii_destroy(eth->sgmii);
 	mtk_unreg_dev(eth);
 	mtk_free_dev(eth);
 	cancel_work_sync(&eth->pending_work);
@@ -4583,7 +4584,7 @@ static int mtk_probe(struct platform_device *pdev)
 		if (!eth->sgmii)
 			return -ENOMEM;
 
-		err = mtk_sgmii_init(eth->sgmii, pdev->dev.of_node,
+		err = mtk_sgmii_init(eth->sgmii, eth->dev, pdev->dev.of_node,
 				     eth->soc->ana_rgc3);
 
 		if (err)
@@ -4595,14 +4596,17 @@ static int mtk_probe(struct platform_device *pdev)
 							    "mediatek,pctl");
 		if (IS_ERR(eth->pctl)) {
 			dev_err(&pdev->dev, "no pctl regmap found\n");
-			return PTR_ERR(eth->pctl);
+			err = PTR_ERR(eth->pctl);
+			goto err_destroy_sgmii;
 		}
 	}
 
 	if (MTK_HAS_CAPS(eth->soc->caps, MTK_NETSYS_V2)) {
 		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-		if (!res)
-			return -EINVAL;
+		if (!res) {
+			err = -EINVAL;
+			goto err_destroy_sgmii;
+		}
 	}
 
 	if (eth->soc->offload_version) {
@@ -4752,6 +4756,8 @@ static int mtk_probe(struct platform_device *pdev)
 
 	return 0;
 
+err_destroy_sgmii:
+	mtk_sgmii_destroy(eth->sgmii);
 err_deinit_ppe:
 	mtk_ppe_deinit(eth);
 	mtk_mdio_cleanup(eth);
drivers/net/ethernet/mediatek/mtk_eth_soc.h +5 -80

107 lines not on this page · raw message

drivers/net/ethernet/mediatek/mtk_sgmii.c +23 -179

229 lines not on this page · raw message

Signature · 1 line
2.39.1
author maintainer
#12 lore raw

PATCH v7 12/12 net: dsa: mt7530: use external PCS driver

In reply to Daniel Golle

Implement regmap access wrappers, for now only to be used by the pcs-mtk driver.
Make use of external PCS driver and drop the reduntant implementation in mt7530.c.
As a nice side effect the SGMII registers can now also more easily be inspected for debugging via /sys/kernel/debug/regmap.

---
 drivers/net/dsa/Kconfig  |   1 +
 drivers/net/dsa/mt7530.c | 277 ++++++++++-----------------------------
 drivers/net/dsa/mt7530.h |  47 +------
 3 files changed, 71 insertions(+), 254 deletions(-)
drivers/net/dsa/Kconfig +1 -0
index f6f3b43dfb06..6b45fa8b6907 100644
@@ -38,6 +38,7 @@ config NET_DSA_MT7530
 	tristate "MediaTek MT7530 and MT7531 Ethernet switch support"
 	select NET_DSA_TAG_MTK
 	select MEDIATEK_GE_PHY
+	select PCS_MTK_LYNXI
 	help
 	  This enables support for the MediaTek MT7530 and MT7531 Ethernet
 	  switch chips. Multi-chip module MT7530 in MT7621AT, MT7621DAT,
drivers/net/dsa/mt7530.c +66 -211

360 lines not on this page · raw message

drivers/net/dsa/mt7530.h +4 -43

64 lines not on this page · raw message

Signature · 1 line
2.39.1
#13 lore raw
In reply to Daniel Golle

Hi Daniel,

Please don't be so quick to send the next revision as soon as you receive comments on a series - as has just been demonstrated, I've replied to Rob's comment about moving the binding to clocks which I don't agree with having read the documentation.

Posting a new series so quickly cuts off any hope of a sensible discussion, and leads to people having to scramble to say "no, we're still discussing the previous series" to possibly prevent netdev applying the patches before the discussion has reached a conclusion.

Thanks.

Quoted 89 lines · Daniel Golle

This series brings a variety of fixes and enhancements for mtk_eth_soc, adds support for the MT7981 SoC and facilitates sharing the SGMII PCS code between mtk_eth_soc and mt7530.

Note that this series depends on commit 697c3892d825 ("regmap: apply reg_base and reg_downshift for single register ops") to not break mt7530 pcs register access.

The whole series has been tested on MT7622+MT7531 (BPi-R64), MT7623+MT7530 (BPi-R2) and MT7981+GPY211 (GL.iNet GL-MT3000).

Changes since v6:
* label MAC MCR bit 12 in 08/12, MediaTek replied explaining its function
* move mediatek,sgmiisys bindings to Documentation/devicetree/bindings/clock

Changes since v5:
* drop dev pointer also from struct mtk_sgmii, pass it as function paramter instead
* address comments left for dt-bindings
* minor improvements to commit messages

Changes since v4:
* remove unused dev pointer in struct pcs_mtk_lynxi
* squash link timer check into correct follow-up patch

Changes since v3:
* remove unused #define's
* use BMCR_* instead of #define'ing our own constants
* return before changing registers in case of invalid link timer

Changes since v2:
* improve dt-bindings, convert sgmisys bindings to dt-schema yaml
* fix typo

Changes since v1:
* apply reverse xmas tree everywhere
* improve commit descriptions
* add dt binding documentation
* various small changes addressing all comments received for v1

Daniel Golle (12):
net: ethernet: mtk_eth_soc: add support for MT7981 SoC
dt-bindings: net: mediatek,net: add mt7981-eth binding
dt-bindings: arm: mediatek: sgmiisys: Convert to DT schema
dt-bindings: arm: mediatek: sgmiisys: add MT7981 SoC
net: ethernet: mtk_eth_soc: set MDIO bus clock frequency
net: ethernet: mtk_eth_soc: reset PCS state
net: ethernet: mtk_eth_soc: only write values if needed
net: ethernet: mtk_eth_soc: fix RX data corruption issue
net: ethernet: mtk_eth_soc: ppe: add support for flow accounting
net: pcs: add driver for MediaTek SGMII PCS
net: ethernet: mtk_eth_soc: switch to external PCS driver
net: dsa: mt7530: use external PCS driver

 .../arm/mediatek/mediatek,sgmiisys.txt        |  27 --
 .../bindings/clock/mediatek,sgmiisys.yaml     |  55 ++++
 .../devicetree/bindings/net/mediatek,net.yaml |  52 ++-
 MAINTAINERS                                   |   7 +
 drivers/net/dsa/Kconfig                       |   1 +
 drivers/net/dsa/mt7530.c                      | 277 ++++------------
 drivers/net/dsa/mt7530.h                      |  47 +--
 drivers/net/ethernet/mediatek/Kconfig         |   2 +
 drivers/net/ethernet/mediatek/mtk_eth_path.c  |  14 +-
 drivers/net/ethernet/mediatek/mtk_eth_soc.c   |  67 +++-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h   | 105 +++---
 drivers/net/ethernet/mediatek/mtk_ppe.c       | 114 ++++++-
 drivers/net/ethernet/mediatek/mtk_ppe.h       |  25 +-
 .../net/ethernet/mediatek/mtk_ppe_debugfs.c   |   9 +-
 .../net/ethernet/mediatek/mtk_ppe_offload.c   |   8 +
 drivers/net/ethernet/mediatek/mtk_ppe_regs.h  |  14 +
 drivers/net/ethernet/mediatek/mtk_sgmii.c     | 192 ++---------
 drivers/net/pcs/Kconfig                       |   7 +
 drivers/net/pcs/Makefile                      |   1 +
 drivers/net/pcs/pcs-mtk-lynxi.c               | 303 ++++++++++++++++++
 include/linux/pcs/pcs-mtk-lynxi.h             |  13 +
 21 files changed, 802 insertions(+), 538 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/arm/mediatek/mediatek,sgmiisys.txt
 create mode 100644 Documentation/devicetree/bindings/clock/mediatek,sgmiisys.yaml
 create mode 100644 drivers/net/pcs/pcs-mtk-lynxi.c
 create mode 100644 include/linux/pcs/pcs-mtk-lynxi.h

base-commit: 9d9019bcea1aac7eed64a1a4966282b6b7b141c8

Signature · 1 line
2.39.1
Signature · 2 lines
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!