btrfs: scrub: update last_physical more frequently
PATCH 2/2 btrfs: scrub: update last_physical after scrubing one stripe
In reply to Qu WenruoCurrently sctx->stat.last_physical only got updated in the following cases:
- When the last stripe of a non-RAID56 chunk is scrubbed This implies a pitfall, if the last stripe is at the chunk boundary, and we finished the scrub of the whole chunk, we won't update last_physical at all until the next chunk.
- When a P/Q stripe of a RAID56 chunk is scrubbed
This leads makes sctx->stat.last_physical to be not update for a long time if we're scrubbing a large data chunk (which can go up to 10GiB).
And if scrub is cancelled halfway, we would restart from last_physical, but that last_physical is only updated to the last finished chunk end, we would re-scrub the same chunk again.
This can waste a lot of time especially when the chunk is huge.
Fix the problem by properly updating @last_physical after each stripe is scrubbed.
And since we're here, for the sake of consistency, use spin lock to protect the update of @last_physical, just like all the remaining call sites touching sctx->stat.
--- fs/btrfs/scrub.c | 4 ++++ 1 file changed, 4 insertions(+)
fs/btrfs/scrub.c +4 -0
@@ -1872,6 +1872,8 @@ static int flush_scrub_stripes(struct scrub_ctx *sctx) stripe = &sctx->stripes[i];wait_scrub_stripe_io (stripe); + sctx->stat.last_physical = stripe->physical + +stripe_length (stripe);scrub_reset_stripe (stripe); } out:
@@ -2337,6 +2339,8 @@ static noinline_for_stack int scrub_stripe(struct scrub_ctx *sctx, stripe_logical += chunk_logical; ret =scrub_raid56_parity_stripe (sctx, scrub_dev, bg, map, stripe_logical); + sctx->stat.last_physical =min (physical +BTRFS_STRIPE_LEN , + physical_end);if (ret) goto out; goto next;
Signature · 1 line
2.44.0
PATCH 1/2 btrfs: extract the stripe length calculation into a helper
In reply to Qu WenruoCurrently there are two location which needs to calculate the real length of a stripe (which can be at the end of a chunk, and the chunk size may not always be 64K aligned).
Extract them into a helper as we're going to have a third user soon.
--- fs/btrfs/scrub.c | 17 +++++++++++------ 1 file changed, 11 insertions(+), 6 deletions(-)
fs/btrfs/scrub.c +11 -6
@@ -1648,14 +1648,21 @@ static void scrub_reset_stripe(struct scrub_stripe *stripe) } } +static u32 stripe_length (struct scrub_stripe *stripe) +{ +ASSERT (stripe->bg); + +return min (BTRFS_STRIPE_LEN , + stripe->bg->start + stripe->bg->length - stripe->logical); + +} +static void scrub_submit_extent_sector_read (struct scrub_ctx *sctx,struct scrub_stripe *stripe) {struct btrfs_fs_info *fs_info = stripe->bg->fs_info;struct btrfs_bio *bbio =NULL ; -unsigned int nr_sectors =min (BTRFS_STRIPE_LEN , stripe->bg->start + - stripe->bg->length - stripe->logical) >> - fs_info->sectorsize_bits; +unsigned int nr_sectors =stripe_length (stripe) >> fs_info->sectorsize_bits;u64 stripe_len =BTRFS_STRIPE_LEN ;int mirror = stripe->mirror_num;int i;
@@ -1725,9 +1732,7 @@ static void scrub_submit_initial_read(struct scrub_ctx *sctx, {struct btrfs_fs_info *fs_info = sctx->fs_info;struct btrfs_bio *bbio; -unsigned int nr_sectors =min (BTRFS_STRIPE_LEN , stripe->bg->start + - stripe->bg->length - stripe->logical) >> - fs_info->sectorsize_bits; +unsigned int nr_sectors =stripe_length (stripe) >> fs_info->sectorsize_bits;int mirror = stripe->mirror_num;ASSERT (stripe->bg);
Signature · 1 line
2.44.0
cover btrfs: scrub: update last_physical more frequently
There is a report in the mailling list that scrub only updates its @last_physical at the end of a chunk.
In fact, it can be worse if there is a used stripe (aka, some extents exist in the stripe) at the chunk boundary.
As it would skip the @last_physical for that chunk at all.
With @last_physical not update for a long time, if we cancel the scrub halfway and resume, the resumed one scrub would only start at @last_physical, meaning a lot of scrubbed extents would be re-scrubbed, wasting quite some IO and CPU.
This patchset would fix it by updateing @last_physical for each finished stripe (including both P/Q stripe of RAID56, and all data stripes for all profiles), so that even if the scrub is cancelled, we at most re-scrub one stripe.
Qu Wenruo (2):
btrfs: extract the stripe length calculation into a helper
btrfs: scrub: update last_physical after scrubing one stripe
fs/btrfs/scrub.c | 21 +++++++++++++++------ 1 file changed, 15 insertions(+), 6 deletions(-)
Signature · 1 line
2.44.0
Re: [PATCH 1/2] btrfs: extract the stripe length calculation into a helper
In reply to Qu WenruoLooks good,
Ping?
Any feedback on this small series?
Thanks,
Qu
Quoted 23 lines · Qu Wenruo
There is a report in the mailling list that scrub only updates its @last_physical at the end of a chunk.
In fact, it can be worse if there is a used stripe (aka, some extents exist in the stripe) at the chunk boundary.
As it would skip the @last_physical for that chunk at all.With @last_physical not update for a long time, if we cancel the scrub halfway and resume, the resumed one scrub would only start at @last_physical, meaning a lot of scrubbed extents would be re-scrubbed, wasting quite some IO and CPU.
This patchset would fix it by updateing @last_physical for each finished stripe (including both P/Q stripe of RAID56, and all data stripes for all profiles), so that even if the scrub is cancelled, we at most re-scrub one stripe.
Qu Wenruo (2):
btrfs: extract the stripe length calculation into a helper
btrfs: scrub: updatelast_physicalafter scrubing one stripefs/btrfs/scrub.c | 21 +++++++++++++++------ 1 file changed, 15 insertions(+), 6 deletions(-)