Skip to contentSkip to conversation

sh: Common PCI Framework driver support.

PATCH In review Yoshinori Sato 2 participants 17 messages Apr 4, 2024 – Apr 5, 2024 1 message not in the archive

Subsystems (12)
lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

Yoshinori Sato

author maintainer
#1 lore raw

PATCH v7 9/36 sh: Common PCI Framework driver support.

Add New OF based PCI Host driver.
This driver conflicts some point in legacy PCI driver. To resolve the conflict, I made some changes to the legacy driver.

---
 arch/sh/include/asm/io.h  |  6 ++++++
 arch/sh/include/asm/pci.h |  4 ++++
 arch/sh/kernel/iomap.c    | 18 ++++++++++++++++++
 3 files changed, 28 insertions(+)
arch/sh/include/asm/io.h +6 -0
index 5c544cf5201b..29b5f996cde3 100644
@@ -20,6 +20,7 @@
 #include <asm/page.h>
 #include <linux/pgtable.h>
 #include <asm-generic/iomap.h>
+#include <linux/ioport.h>
 
 #define __IO_PREFIX     generic
 #include <asm/io_generic.h>
@@ -310,4 +311,9 @@ unsigned long long poke_real_address_q(unsigned long long addr,
 int valid_phys_addr_range(phys_addr_t addr, size_t size);
 int valid_mmap_phys_addr_range(unsigned long pfn, size_t size);
 
+#if defined(CONFIG_PCI) && !defined(CONFIG_GENERIC_IOMAP)
+#define pci_remap_iospace pci_remap_iospace
+int pci_remap_iospace(const struct resource *res, phys_addr_t phys_addr);
+#endif
+
 #endif /* __ASM_SH_IO_H */
arch/sh/include/asm/pci.h +4 -0
index 54c30126ea17..92b3bd604319 100644
@@ -2,6 +2,7 @@
 #ifndef __ASM_SH_PCI_H
 #define __ASM_SH_PCI_H
 
+#ifndef CONFIG_SH_DEVICE_TREE
 /* Can be used to override the logic in pci_scan_bus for skipping
    already-configured bus numbers - to be used for buggy BIOSes
    or architectures with incomplete PCI setup by the loader */
@@ -88,4 +89,7 @@ static inline int pci_proc_domain(struct pci_bus *bus)
 	return hose->need_domain_info;
 }
 
+#else /* CONFIG_SH_DEVICE_TREE */
+#include <asm-generic/pci.h>
+#endif
 #endif /* __ASM_SH_PCI_H */
arch/sh/kernel/iomap.c +18 -0
index 0a0dff4e66de..d1b8e496ca23 100644
@@ -160,3 +160,21 @@ void iowrite32_rep(void __iomem *addr, const void *src, unsigned long count)
 	mmio_outsl(addr, src, count);
 }
 EXPORT_SYMBOL(iowrite32_rep);
+
+#if defined(pci_remap_iospace)
+int pci_remap_iospace(const struct resource *res, phys_addr_t phys_addr)
+{
+	unsigned long vaddr = res->start;
+
+	if (!(res->flags & IORESOURCE_IO))
+		return -EINVAL;
+
+	if (res->end > IO_SPACE_LIMIT)
+		return -EINVAL;
+
+	__set_io_port_base(phys_addr);
+	return vmap_page_range(vaddr, vaddr + resource_size(res), phys_addr,
+			       pgprot_device(PAGE_KERNEL));
+}
+EXPORT_SYMBOL(pci_remap_iospace);
+#endif
Signature · 1 line
2.39.2
author maintainer
#2 lore raw

PATCH v7 10/36 pci: pci-sh7751: Add SH7751 PCI driver

In reply to a message not in the archive

Renesas SH7751 CPU Internal PCI Controller driver.

---
 drivers/pci/controller/Kconfig      |   9 +
 drivers/pci/controller/Makefile     |   1 +
 drivers/pci/controller/pci-sh7751.c | 342 ++++++++++++++++++++++++++++
 3 files changed, 352 insertions(+)
 create mode 100644 drivers/pci/controller/pci-sh7751.c
drivers/pci/controller/Kconfig +9 -0
index e534c02ee34f..a2fd917a2e03 100644
@@ -353,6 +353,15 @@ config PCIE_XILINX_CPM
 	  Say 'Y' here if you want kernel support for the
 	  Xilinx Versal CPM host bridge.
 
+config PCI_SH7751
+	bool "Renesas SH7751 PCI controller"
+	depends on OF
+	depends on CPU_SUBTYPE_SH7751 || CPU_SUBTYPE_SH7751R || COMPILE_TEST
+	select PCI_HOST_COMMON
+	help
+	  Say 'Y' here if you want kernel to support the Renesas SH7751 PCI
+	  Host Bridge driver.
+
 source "drivers/pci/controller/cadence/Kconfig"
 source "drivers/pci/controller/dwc/Kconfig"
 source "drivers/pci/controller/mobiveil/Kconfig"
drivers/pci/controller/Makefile +1 -0
index f2b19e6174af..aa97e5d74e58 100644
@@ -40,6 +40,7 @@ obj-$(CONFIG_PCI_LOONGSON) += pci-loongson.o
 obj-$(CONFIG_PCIE_HISI_ERR) += pcie-hisi-error.o
 obj-$(CONFIG_PCIE_APPLE) += pcie-apple.o
 obj-$(CONFIG_PCIE_MT7621) += pcie-mt7621.o
+obj-$(CONFIG_PCI_SH7751) += pci-sh7751.o
 
 # pcie-hisi.o quirks are needed even without CONFIG_PCIE_DW
 obj-y				+= dwc/
drivers/pci/controller/pci-sh7751.c new file +342 -0

342 lines not on this page · raw message

Signature · 1 line
2.39.2
author maintainer
#3 lore raw

PATCH v7 11/36 dt-bindings: pci: pci-sh7751: Add SH7751 PCI

In reply to a message not in the archive

Renesas SH7751 PCI Controller json-schema.

---
 .../bindings/pci/renesas,sh7751-pci.yaml      | 89 +++++++++++++++++++
 1 file changed, 89 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml
Documentation/devicetree/bindings/pci/renesas,sh7751-pci.yaml new file +89 -0
new file mode 100644
index 000000000000..115c2bb67339
@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/renesas,sh7751-pci.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas SH7751 PCI Host controller
+
+maintainers:
+  - Yoshinori Sato <[email protected]>
+
+allOf:
+  - $ref: /schemas/pci/pci-bus.yaml#
+
+properties:
+  compatible:
+    const: renesas,sh7751-pci
+
+  reg:
+    minItems: 2
+    maxItems: 2
+
+  reg-names:
+    items:
+      - const: PCI Controller
+      - const: Bus State Controller
+
+  "#interrupt-cells":
+    const: 1
+
+  "#address-cells":
+    const: 3
+
+  "#size-cells":
+    const: 2
+
+  ranges: true
+
+  dma-ranges: true
+
+  interrupt-controller: true
+
+  renesas,bus-arbit-round-robin:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: |
+      Set DMA bus arbitration to round robin.
+
+required:
+  - compatible
+  - reg
+  - "#interrupt-cells"
+  - "#address-cells"
+  - "#size-cells"
+  - ranges
+  - interrupt-map
+  - interrupt-map-mask
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    pci@fe200000 {
+            compatible = "renesas,sh7751-pci";
+            #address-cells = <3>;
+            #size-cells = <2>;
+            #interrupt-cells = <1>;
+            interrupt-controller;
+            device_type = "pci";
+            bus-range = <0 0>;
+            ranges = <0x02000000 0 0xfd000000 0xfd000000 0 0x01000000>,
+                     <0x01000000 0 0x00000000 0xfe240000 0 0x00040000>;
+            dma-ranges = <0x02000000 0 0xc000000 0x0c000000 0 0x04000000>;
+            reg = <0xfe200000 0x0400>,
+                  <0xff800000 0x0100>;
+            interrupt-map = <0x0000 0 0 1 &julianintc 5 IRQ_TYPE_LEVEL_LOW>,
+                            <0x0000 0 0 2 &julianintc 6 IRQ_TYPE_LEVEL_LOW>,
+                            <0x0000 0 0 3 &julianintc 7 IRQ_TYPE_LEVEL_LOW>,
+                            <0x0000 0 0 4 &julianintc 8 IRQ_TYPE_LEVEL_LOW>,
+                            <0x0800 0 0 1 &julianintc 6 IRQ_TYPE_LEVEL_LOW>,
+                            <0x0800 0 0 2 &julianintc 7 IRQ_TYPE_LEVEL_LOW>,
+                            <0x0800 0 0 3 &julianintc 8 IRQ_TYPE_LEVEL_LOW>,
+                            <0x0800 0 0 4 &julianintc 5 IRQ_TYPE_LEVEL_LOW>,
+                            <0x1000 0 0 1 &julianintc 7 IRQ_TYPE_LEVEL_LOW>,
+                            <0x1000 0 0 2 &julianintc 8 IRQ_TYPE_LEVEL_LOW>,
+                            <0x1000 0 0 3 &julianintc 5 IRQ_TYPE_LEVEL_LOW>,
+                            <0x1000 0 0 4 &julianintc 6 IRQ_TYPE_LEVEL_LOW>;
+            interrupt-map-mask = <0x1800 0 0 7>;
+    };
Signature · 1 line
2.39.2
author maintainer
#4 lore raw

PATCH v7 12/36 dt-bindings: clock: sh7750-cpg: Add renesas,sh7750-cpg header.

In reply to a message not in the archive

SH7750 CPG Clock output define.

---
 .../bindings/clock/renesas,sh7750-cpg.yaml    | 105 ++++++++++++++++++
 include/dt-bindings/clock/sh7750-cpg.h        |  26 +++++
 2 files changed, 131 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml
 create mode 100644 include/dt-bindings/clock/sh7750-cpg.h
Documentation/devicetree/bindings/clock/renesas,sh7750-cpg.yaml new file +105 -0
new file mode 100644
index 000000000000..04c10b0834ee
@@ -0,0 +1,105 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/renesas,sh7750-cpg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas SH7750/7751 Clock Pulse Generator (CPG)
+
+maintainers:
+  - Yoshinori Sato <[email protected]>
+
+description:
+  The Clock Pulse Generator (CPG) generates core clocks for the SoC.  It
+  includes PLLs, and variable ratio dividers.
+
+  The CPG may also provide a Clock Domain for SoC devices, in combination with
+  the CPG Module Stop (MSTP) Clocks.
+
+properties:
+  compatible:
+    enum:
+      - renesas,sh7750-cpg             # SH7750
+      - renesas,sh7750s-cpg            # SH775S
+      - renesas,sh7750r-cpg            # SH7750R
+      - renesas,sh7751-cpg             # SH7751
+      - renesas,sh7751r-cpg            # SH7751R
+
+  reg: true
+
+  reg-names: true
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: extal
+
+  '#clock-cells':
+    const: 1
+
+  renesas,mode:
+    description: Board-specific settings of the MD[0-2] pins on SoC
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 6
+
+  '#power-domain-cells':
+    const: 0
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - clocks
+  - clock-names
+  - '#clock-cells'
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - renesas,sh7750-cpg
+              - renesas,sh7750s-cpg
+    then:
+      properties:
+        reg:
+          maxItems: 1
+        reg-names:
+          items:
+            - const: FRQCR
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - renesas,sh7750r-cpg
+              - renesas,sh7751-cpg
+              - renesas,sh7751r-cpg
+    then:
+      properties:
+        reg:
+          maxItems: 2
+        reg-names:
+          items:
+            - const: FRQCR
+            - const: CLKSTP00
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/sh7750-cpg.h>
+    cpg: clock-controller@ffc00000 {
+        #clock-cells = <1>;
+        #power-domain-cells = <0>;
+        compatible = "renesas,sh7751r-cpg";
+        clocks = <&extal>;
+        clock-names = "extal";
+        reg = <0xffc00000 20>, <0xfe0a0000 16>;
+        reg-names = "FRQCR", "CLKSTP00";
+        renesas,mode = <0>;
+    };
include/dt-bindings/clock/sh7750-cpg.h new file +26 -0
new file mode 100644
index 000000000000..ec267be91adf
@@ -0,0 +1,26 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+ *
+ * Copyright 2023 Yoshinori Sato
+ */
+
+#ifndef __DT_BINDINGS_CLOCK_SH7750_H__
+#define __DT_BINDINGS_CLOCK_SH7750_H__
+
+#define SH7750_CPG_PLLOUT	0
+
+#define SH7750_CPG_PCK		1
+#define SH7750_CPG_BCK		2
+#define SH7750_CPG_ICK		3
+
+#define SH7750_MSTP_SCI		4
+#define SH7750_MSTP_RTC		5
+#define SH7750_MSTP_TMU012	6
+#define SH7750_MSTP_SCIF	7
+#define SH7750_MSTP_DMAC	8
+#define SH7750_MSTP_UBC		9
+#define SH7750_MSTP_SQ		10
+#define SH7750_CSTP_INTC	11
+#define SH7750_CSTP_TMU34	12
+#define SH7750_CSTP_PCIC	13
+
+#endif
Signature · 1 line
2.39.2
author maintainer
#5 lore raw

PATCH v7 13/36 clk: Compatible with narrow registers

In reply to a message not in the archive

divider and gate only support 32-bit registers.
Older hardware uses narrower registers, so I want to be able to handle 8-bit and 16-bit wide registers.

Seven clk_divider flags are used, and if I add flags for 8bit access and 16bit access, 8bit will not be enough, so I expanded it to u16.

---
 drivers/clk/clk-divider.c    | 56 +++++++++++++++++++++-----------
 drivers/clk/clk-gate.c       | 62 ++++++++++++++++++++++++++++--------
 include/linux/clk-provider.h | 22 ++++++++++---
 3 files changed, 103 insertions(+), 37 deletions(-)
drivers/clk/clk-divider.c +37 -19
index a2c2b5203b0a..a1b5187cd63d 100644
@@ -26,20 +26,38 @@
  * parent - fixed parent.  No clk_set_parent support
  */
 
-static inline u32 clk_div_readl(struct clk_divider *divider)
-{
-	if (divider->flags & CLK_DIVIDER_BIG_ENDIAN)
-		return ioread32be(divider->reg);
-
-	return readl(divider->reg);
+static inline u32 clk_div_read(struct clk_divider *divider)
+{
+	if (divider->flags & CLK_DIVIDER_REG_8BIT)
+		return readb(divider->reg);
+	else if (divider->flags & CLK_DIVIDER_REG_16BIT) {
+		if (divider->flags & CLK_DIVIDER_BIG_ENDIAN)
+			return ioread16be(divider->reg);
+		else
+			return readw(divider->reg);
+	} else {
+		if (divider->flags & CLK_DIVIDER_BIG_ENDIAN)
+			return ioread32be(divider->reg);
+		else
+			return readl(divider->reg);
+	}
 }
 
-static inline void clk_div_writel(struct clk_divider *divider, u32 val)
+static inline void clk_div_write(struct clk_divider *divider, u32 val)
 {
-	if (divider->flags & CLK_DIVIDER_BIG_ENDIAN)
-		iowrite32be(val, divider->reg);
-	else
-		writel(val, divider->reg);
+	if (divider->flags & CLK_DIVIDER_REG_8BIT)
+		writeb(val, divider->reg);
+	else if (divider->flags & CLK_DIVIDER_REG_16BIT) {
+		if (divider->flags & CLK_DIVIDER_BIG_ENDIAN)
+			iowrite16be(val, divider->reg);
+		else
+			writew(val, divider->reg);
+	} else {
+		if (divider->flags & CLK_DIVIDER_BIG_ENDIAN)
+			iowrite32be(val, divider->reg);
+		else
+			writel(val, divider->reg);
+	}
 }
 
 static unsigned int _get_table_maxdiv(const struct clk_div_table *table,
@@ -152,7 +170,7 @@ static unsigned long clk_divider_recalc_rate(struct clk_hw *hw,
 	struct clk_divider *divider = to_clk_divider(hw);
 	unsigned int val;
 
-	val = clk_div_readl(divider) >> divider->shift;
+	val = clk_div_read(divider) >> divider->shift;
 	val &= clk_div_mask(divider->width);
 
 	return divider_recalc_rate(hw, parent_rate, val, divider->table,
@@ -434,7 +452,7 @@ static long clk_divider_round_rate(struct clk_hw *hw, unsigned long rate,
 	if (divider->flags & CLK_DIVIDER_READ_ONLY) {
 		u32 val;
 
-		val = clk_div_readl(divider) >> divider->shift;
+		val = clk_div_read(divider) >> divider->shift;
 		val &= clk_div_mask(divider->width);
 
 		return divider_ro_round_rate(hw, rate, prate, divider->table,
@@ -455,7 +473,7 @@ static int clk_divider_determine_rate(struct clk_hw *hw,
 	if (divider->flags & CLK_DIVIDER_READ_ONLY) {
 		u32 val;
 
-		val = clk_div_readl(divider) >> divider->shift;
+		val = clk_div_read(divider) >> divider->shift;
 		val &= clk_div_mask(divider->width);
 
 		return divider_ro_determine_rate(hw, req, divider->table,
@@ -505,11 +523,11 @@ static int clk_divider_set_rate(struct clk_hw *hw, unsigned long rate,
 	if (divider->flags & CLK_DIVIDER_HIWORD_MASK) {
 		val = clk_div_mask(divider->width) << (divider->shift + 16);
 	} else {
-		val = clk_div_readl(divider);
+		val = clk_div_read(divider);
 		val &= ~(clk_div_mask(divider->width) << divider->shift);
 	}
 	val |= (u32)value << divider->shift;
-	clk_div_writel(divider, val);
+	clk_div_write(divider, val);
 
 	if (divider->lock)
 		spin_unlock_irqrestore(divider->lock, flags);
@@ -538,7 +556,7 @@ struct clk_hw *__clk_hw_register_divider(struct device *dev,
 		struct device_node *np, const char *name,
 		const char *parent_name, const struct clk_hw *parent_hw,
 		const struct clk_parent_data *parent_data, unsigned long flags,
-		void __iomem *reg, u8 shift, u8 width, u8 clk_divider_flags,
+		void __iomem *reg, u8 shift, u8 width, u32 clk_divider_flags,
 		const struct clk_div_table *table, spinlock_t *lock)
 {
 	struct clk_divider *div;
@@ -610,7 +628,7 @@ EXPORT_SYMBOL_GPL(__clk_hw_register_divider);
 struct clk *clk_register_divider_table(struct device *dev, const char *name,
 		const char *parent_name, unsigned long flags,
 		void __iomem *reg, u8 shift, u8 width,
-		u8 clk_divider_flags, const struct clk_div_table *table,
+		u32 clk_divider_flags, const struct clk_div_table *table,
 		spinlock_t *lock)
 {
 	struct clk_hw *hw;
@@ -664,7 +682,7 @@ struct clk_hw *__devm_clk_hw_register_divider(struct device *dev,
 		struct device_node *np, const char *name,
 		const char *parent_name, const struct clk_hw *parent_hw,
 		const struct clk_parent_data *parent_data, unsigned long flags,
-		void __iomem *reg, u8 shift, u8 width, u8 clk_divider_flags,
+		void __iomem *reg, u8 shift, u8 width, u32 clk_divider_flags,
 		const struct clk_div_table *table, spinlock_t *lock)
 {
 	struct clk_hw **ptr, *hw;
drivers/clk/clk-gate.c +49 -13

102 lines not on this page · raw message

include/linux/clk-provider.h +17 -5
index 4a537260f655..eaa6ff1d0b2e 100644
@@ -508,12 +508,16 @@ void of_fixed_clk_setup(struct device_node *np);
  * CLK_GATE_BIG_ENDIAN - by default little endian register accesses are used for
  *	the gate register.  Setting this flag makes the register accesses big
  *	endian.
+ * CLK_GATE_REG_8BIT - by default 32bit register accesses are used for
+ *	the gate register.  Setting this flag makes the register accesses 8bit.
+ * CLK_GATE_REG_16BIT - by default 32bit register accesses are used for
+ *	the gate register.  Setting this flag makes the register accesses 16bit.
  */
 struct clk_gate {
 	struct clk_hw hw;
 	void __iomem	*reg;
 	u8		bit_idx;
-	u8		flags;
+	u32		flags;
 	spinlock_t	*lock;
 };
 
@@ -522,6 +526,8 @@ struct clk_gate {
 #define CLK_GATE_SET_TO_DISABLE		BIT(0)
 #define CLK_GATE_HIWORD_MASK		BIT(1)
 #define CLK_GATE_BIG_ENDIAN		BIT(2)
+#define CLK_GATE_REG_8BIT		BIT(3)
+#define CLK_GATE_REG_16BIT		BIT(4)
 
 extern const struct clk_ops clk_gate_ops;
 struct clk_hw *__clk_hw_register_gate(struct device *dev,
@@ -675,13 +681,17 @@ struct clk_div_table {
  * CLK_DIVIDER_BIG_ENDIAN - By default little endian register accesses are used
  *	for the divider register.  Setting this flag makes the register accesses
  *	big endian.
+ * CLK_DIVIDER_REG_8BIT - by default 32bit register accesses are used for
+ *	the gate register.  Setting this flag makes the register accesses 8bit.
+ * CLK_DIVIDER_REG_16BIT - by default 32bit register accesses are used for
+ *	the gate register.  Setting this flag makes the register accesses 16bit.
  */
 struct clk_divider {
 	struct clk_hw	hw;
 	void __iomem	*reg;
 	u8		shift;
 	u8		width;
-	u8		flags;
+	u16		flags;
 	const struct clk_div_table	*table;
 	spinlock_t	*lock;
 };
@@ -697,6 +707,8 @@ struct clk_divider {
 #define CLK_DIVIDER_READ_ONLY		BIT(5)
 #define CLK_DIVIDER_MAX_AT_ZERO		BIT(6)
 #define CLK_DIVIDER_BIG_ENDIAN		BIT(7)
+#define CLK_DIVIDER_REG_8BIT		BIT(8)
+#define CLK_DIVIDER_REG_16BIT		BIT(9)
 
 extern const struct clk_ops clk_divider_ops;
 extern const struct clk_ops clk_divider_ro_ops;
@@ -726,18 +738,18 @@ struct clk_hw *__clk_hw_register_divider(struct device *dev,
 		struct device_node *np, const char *name,
 		const char *parent_name, const struct clk_hw *parent_hw,
 		const struct clk_parent_data *parent_data, unsigned long flags,
-		void __iomem *reg, u8 shift, u8 width, u8 clk_divider_flags,
+		void __iomem *reg, u8 shift, u8 width, u32 clk_divider_flags,
 		const struct clk_div_table *table, spinlock_t *lock);
 struct clk_hw *__devm_clk_hw_register_divider(struct device *dev,
 		struct device_node *np, const char *name,
 		const char *parent_name, const struct clk_hw *parent_hw,
 		const struct clk_parent_data *parent_data, unsigned long flags,
-		void __iomem *reg, u8 shift, u8 width, u8 clk_divider_flags,
+		void __iomem *reg, u8 shift, u8 width, u32 clk_divider_flags,
 		const struct clk_div_table *table, spinlock_t *lock);
 struct clk *clk_register_divider_table(struct device *dev, const char *name,
 		const char *parent_name, unsigned long flags,
 		void __iomem *reg, u8 shift, u8 width,
-		u8 clk_divider_flags, const struct clk_div_table *table,
+		u32 clk_divider_flags, const struct clk_div_table *table,
 		spinlock_t *lock);
 /**
  * clk_register_divider - register a divider clock with the clock framework
Signature · 1 line
2.39.2
author maintainer
#6 lore raw

PATCH v7 14/36 clk: renesas: Add SH7750/7751 CPG Driver

In reply to a message not in the archive

Renesas SH7750 and SH7751 series CPG driver. This driver supported frequency control and clock gating.

---
 drivers/clk/renesas/Kconfig      |  13 +-
 drivers/clk/renesas/Makefile     |   1 +
 drivers/clk/renesas/clk-sh7750.c | 480 +++++++++++++++++++++++++++++++
 3 files changed, 491 insertions(+), 3 deletions(-)
 create mode 100644 drivers/clk/renesas/clk-sh7750.c
drivers/clk/renesas/Kconfig +10 -3
index d252150402e8..482efcb6e76e 100644
@@ -1,8 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0
 
 config CLK_RENESAS
-	bool "Renesas SoC clock support" if COMPILE_TEST && !ARCH_RENESAS
-	default y if ARCH_RENESAS
+	bool "Renesas SoC clock support" if COMPILE_TEST && !ARCH_RENESAS && !SUPERH
+	default y if ARCH_RENESAS || SUPERH
 	select CLK_EMEV2 if ARCH_EMEV2
 	select CLK_RZA1 if ARCH_R7S72100
 	select CLK_R7S9210 if ARCH_R7S9210
@@ -41,6 +41,9 @@ config CLK_RENESAS
 	select CLK_R9A08G045 if ARCH_R9A08G045
 	select CLK_R9A09G011 if ARCH_R9A09G011
 	select CLK_SH73A0 if ARCH_SH73A0
+	select CLK_SH7750 if CPU_SUBTYPE_SH7750 || CPU_SUBTYPE_SH7750S || \
+	                     CPU_SUBTYPE_SH7750R || CPU_SUBTYPE_SH7751 || \
+			     CPU_SUBTYPE_SH7751R
 
 if CLK_RENESAS
 
@@ -198,7 +201,6 @@ config CLK_SH73A0
 	select CLK_RENESAS_CPG_MSTP
 	select CLK_RENESAS_DIV6
 
-
 # Family
 config CLK_RCAR_CPG_LIB
 	bool "CPG/MSSR library functions" if COMPILE_TEST
@@ -228,6 +230,11 @@ config CLK_RZG2L
 	bool "Renesas RZ/{G2L,G2UL,G3S,V2L} family clock support" if COMPILE_TEST
 	select RESET_CONTROLLER
 
+config CLK_SH7750
+	bool "Renesas SH7750/7751 family clock support" if COMPILE_TEST
+	help
+	  This is a driver for SH7750 / SH7751 CPG.
+
 # Generic
 config CLK_RENESAS_CPG_MSSR
 	bool "CPG/MSSR clock support" if COMPILE_TEST
drivers/clk/renesas/Makefile +1 -0
index f7e18679c3b8..ea0ffa8d59c4 100644
@@ -38,6 +38,7 @@ obj-$(CONFIG_CLK_R9A07G054)		+= r9a07g044-cpg.o
 obj-$(CONFIG_CLK_R9A08G045)		+= r9a08g045-cpg.o
 obj-$(CONFIG_CLK_R9A09G011)		+= r9a09g011-cpg.o
 obj-$(CONFIG_CLK_SH73A0)		+= clk-sh73a0.o
+obj-$(CONFIG_CLK_SH7750)		+= clk-sh7750.o
 
 # Family
 obj-$(CONFIG_CLK_RCAR_CPG_LIB)		+= rcar-cpg-lib.o
drivers/clk/renesas/clk-sh7750.c new file +480 -0

480 lines not on this page · raw message

Signature · 1 line
2.39.2
author maintainer
#7 lore raw

PATCH v7 15/36 irqchip: Add SH7751 INTC driver

In reply to a message not in the archive

Renesas SH7751 Internal interrupt controller driver.

---
 drivers/irqchip/Kconfig              |   8 +
 drivers/irqchip/Makefile             |   1 +
 drivers/irqchip/irq-renesas-sh7751.c | 282 +++++++++++++++++++++++++++
 3 files changed, 291 insertions(+)
 create mode 100644 drivers/irqchip/irq-renesas-sh7751.c
drivers/irqchip/Kconfig +8 -0
index 72c07a12f5e1..33badb5b4f00 100644
@@ -690,4 +690,12 @@ config SUNPLUS_SP7021_INTC
 	  chained controller, routing all interrupt source in P-Chip to
 	  the primary controller on C-Chip.
 
+config RENESAS_SH7751_INTC
+	bool "Renesas SH7751 Interrupt Controller"
+	depends on SH_DEVICE_TREE || COMPILE_TEST
+	select IRQ_DOMAIN_HIERARCHY
+	help
+	  Support for the Renesas SH7751 On-chip interrupt controller.
+	  And external interrupt encoder for some targets.
+
 endmenu
drivers/irqchip/Makefile +1 -0
index ec4a18380998..51855034a895 100644
@@ -121,3 +121,4 @@ obj-$(CONFIG_IRQ_IDT3243X)		+= irq-idt3243x.o
 obj-$(CONFIG_APPLE_AIC)			+= irq-apple-aic.o
 obj-$(CONFIG_MCHP_EIC)			+= irq-mchp-eic.o
 obj-$(CONFIG_SUNPLUS_SP7021_INTC)	+= irq-sp7021-intc.o
+obj-$(CONFIG_RENESAS_SH7751_INTC)	+= irq-renesas-sh7751.o
drivers/irqchip/irq-renesas-sh7751.c new file +282 -0

282 lines not on this page · raw message

Signature · 1 line
2.39.2
author maintainer
#8 lore raw

PATCH v7 16/36 dt-bindings: interrupt-controller: renesas,sh7751-intc: Add json-schema

In reply to a message not in the archive

Renesas SH7751 INTC json-schema.

---
 .../renesas,sh7751-intc.yaml                  | 53 +++++++++++++++++++
 1 file changed, 53 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,sh7751-intc.yaml
Documentation/devicetree/bindings/interrupt-controller/renesas,sh7751-intc.yaml new file +53 -0
new file mode 100644
index 000000000000..fb924eff465d
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/renesas,sh7751-intc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas SH7751 Interrupt Controller
+
+maintainers:
+  - Yoshinori Sato <[email protected]>
+
+properties:
+  compatible:
+    items:
+      - const: renesas,sh7751-intc
+
+  '#interrupt-cells':
+    const: 1
+
+  interrupt-controller: true
+
+  reg:
+    maxItems: 2
+
+  reg-names:
+    items:
+      - const: ICR
+      - const: INTPRI00
+
+  renesas,icr-irlm:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: If true four independent interrupt requests mode (ICR.IRLM is 1).
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - '#interrupt-cells'
+  - interrupt-controller
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/renesas,sh7751-intc.h>
+    shintc: interrupt-controller@ffd00000 {
+            compatible = "renesas,sh7751-intc";
+            reg = <0xffd00000 14>, <0xfe080000 128>;
+            reg-names = "ICR", "INTPRI00";
+            #interrupt-cells = <1>;
+            interrupt-controller;
+    };
+...
Signature · 1 line
2.39.2
author maintainer
#9 lore raw

PATCH v7 17/36 irqchip: SH7751 external interrupt encoder with enable gate.

In reply to a message not in the archive

SH7751 have 15 level external interrupt.
It is typically connected to the CPU through a priority encoder that can suppress requests.
This driver provides a way to control those hardware with irqchip.

---
 drivers/irqchip/Kconfig                 |   7 +
 drivers/irqchip/Makefile                |   2 +
 drivers/irqchip/irq-renesas-sh7751irl.c | 221 ++++++++++++++++++++++++
 3 files changed, 230 insertions(+)
 create mode 100644 drivers/irqchip/irq-renesas-sh7751irl.c
drivers/irqchip/Kconfig +7 -0
index 33badb5b4f00..7670fcd6757d 100644
@@ -698,4 +698,11 @@ config RENESAS_SH7751_INTC
 	  Support for the Renesas SH7751 On-chip interrupt controller.
 	  And external interrupt encoder for some targets.
 
+config RENESAS_SH7751IRL_INTC
+	bool "Renesas SH7751 based target IRL encoder support."
+	depends on RENESAS_SH7751_INTC
+	help
+	  Support for External Interrupt encoder
+	  on the some Renesas SH7751 based target.
+
 endmenu
drivers/irqchip/Makefile +2 -0
index 51855034a895..bc21d65441f2 100644
@@ -122,3 +122,5 @@ obj-$(CONFIG_APPLE_AIC)			+= irq-apple-aic.o
 obj-$(CONFIG_MCHP_EIC)			+= irq-mchp-eic.o
 obj-$(CONFIG_SUNPLUS_SP7021_INTC)	+= irq-sp7021-intc.o
 obj-$(CONFIG_RENESAS_SH7751_INTC)	+= irq-renesas-sh7751.o
+obj-$(CONFIG_RENESAS_SH7751IRL_INTC)	+= irq-renesas-sh7751irl.o
+
drivers/irqchip/irq-renesas-sh7751irl.c new file +221 -0

221 lines not on this page · raw message

Signature · 1 line
2.39.2
author maintainer
#10 lore raw

PATCH v7 18/36 dt-bindings: interrupt-controller: renesas,sh7751-irl-ext: Add json-schema

In reply to a message not in the archive

Renesas SH7751 external interrupt encoder json-schema.

---
 .../renesas,sh7751-irl-ext.yaml               | 57 +++++++++++++++++++
 1 file changed, 57 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interrupt-controller/renesas,sh7751-irl-ext.yaml
Documentation/devicetree/bindings/interrupt-controller/renesas,sh7751-irl-ext.yaml new file +57 -0
new file mode 100644
index 000000000000..fc174c0467e7
@@ -0,0 +1,57 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/renesas,sh7751-irl-ext.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas SH7751 external interrupt encoder with enable regs.
+
+maintainers:
+  - Yoshinori Sato <[email protected]>
+
+description:
+  This is the generally used external interrupt encoder on SH7751 based boards.
+
+properties:
+  compatible:
+    items:
+      - const: renesas,sh7751-irl-ext
+
+  reg: true
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    const: 2
+
+  '#address-cells':
+    const: 0
+
+  renesas,set-to-disable:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: Invert enable registers. Setting the bit to 0 enables interrupts.
+
+  renesas,enable-reg:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description: |
+      IRQ enable register bit mapping
+
+required:
+  - compatible
+  - reg
+  - interrupt-controller
+  - '#interrupt-cells'
+  - renesas,enable-reg
+
+additionalProperties: false
+
+examples:
+  - |
+    r2dintc: interrupt-controller@a4000000 {
+        compatible = "renesas,sh7751-irl-ext";
+        reg = <0xa4000000 0x02>;
+        interrupt-controller;
+        #address-cells = <0>;
+        #interrupt-cells = <1>;
+        renesas,enable-reg = <12 9 10 3 0 4 1 2 8 5 6 7 15 15 15 11>;
+    };
Signature · 1 line
2.39.2
author maintainer
#11 lore raw

PATCH v7 19/36 serial: sh-sci: fix SH4 OF support.

In reply to a message not in the archive

- fix earlycon name.
- fix earlyprintk hung (NULL pointer reference).
- fix SERIAL_SH_SCI_EARLYCON enablement

---
 drivers/tty/serial/Kconfig  | 2 +-
 drivers/tty/serial/sh-sci.c | 6 +++---
 2 files changed, 4 insertions(+), 4 deletions(-)
drivers/tty/serial/Kconfig +1 -1
index ffcf4882b25f..dfe5fd436816 100644
@@ -661,7 +661,7 @@ config SERIAL_SH_SCI_EARLYCON
 	depends on SERIAL_SH_SCI=y
 	select SERIAL_CORE_CONSOLE
 	select SERIAL_EARLYCON
-	default ARCH_RENESAS
+	default ARCH_RENESAS || SUPERH
 
 config SERIAL_SH_SCI_DMA
 	bool "DMA support" if EXPERT
drivers/tty/serial/sh-sci.c +3 -3
index e512eaa57ed5..46466fb5a637 100644
@@ -2717,7 +2717,7 @@ static int sci_remap_port(struct uart_port *port)
 	if (port->membase)
 		return 0;
 
-	if (port->dev->of_node || (port->flags & UPF_IOREMAP)) {
+	if ((port->dev && port->dev->of_node) || (port->flags & UPF_IOREMAP)) {
 		port->membase = ioremap(port->mapbase, sport->reg_size);
 		if (unlikely(!port->membase)) {
 			dev_err(port->dev, "can't remap port#%d\n", port->line);
@@ -3545,8 +3545,8 @@ static int __init hscif_early_console_setup(struct earlycon_device *device,
 
 OF_EARLYCON_DECLARE(sci, "renesas,sci", sci_early_console_setup);
 OF_EARLYCON_DECLARE(scif, "renesas,scif", scif_early_console_setup);
-OF_EARLYCON_DECLARE(scif, "renesas,scif-r7s9210", rzscifa_early_console_setup);
-OF_EARLYCON_DECLARE(scif, "renesas,scif-r9a07g044", rzscifa_early_console_setup);
+OF_EARLYCON_DECLARE(rzscifa, "renesas,scif-r7s9210", rzscifa_early_console_setup);
+OF_EARLYCON_DECLARE(rzscifa, "renesas,scif-r9a07g044", rzscifa_early_console_setup);
 OF_EARLYCON_DECLARE(scifa, "renesas,scifa", scifa_early_console_setup);
 OF_EARLYCON_DECLARE(scifb, "renesas,scifb", scifb_early_console_setup);
 OF_EARLYCON_DECLARE(hscif, "renesas,hscif", hscif_early_console_setup);
Signature · 1 line
2.39.2
#12 lore raw

Re: [DO NOT MERGE v7 19/36] serial: sh-sci: fix SH4 OF support.

Hi Sato-san,

Thanks for the update!

Quoted 1 line · Yoshinori Sato

- fix earlycon name.

Might be wise to explain what was wrong with it...

(because else "scif" will invoke rzscifa_early_console_setup()
on non-DT platforms)

Quoted 9 lines

- fix earlyprintk hung (NULL pointer reference).
- fix SERIAL_SH_SCI_EARLYCON enablement

drivers/tty/serial/sh-sci.c static int sci_remap_port(struct uart_port *port) · line 2720

Quoted 5 lines
drivers/tty/serial/sh-sci.c +1 -1
@@ -2717,7 +2717,7 @@ static int sci_remap_port(struct uart_port *port)
        if (port->membase)
                return 0;
 
-       if (port->dev->of_node || (port->flags & UPF_IOREMAP)) {
+       if ((port->dev && port->dev->of_node) || (port->flags & UPF_IOREMAP)) {

Looks like the dev_of_node() wrapper exists to handle this.

Quoted 4 lines
drivers/tty/serial/sh-sci.c +0 -0
                port->membase = ioremap(port->mapbase, sport->reg_size);
                if (unlikely(!port->membase)) {
                        dev_err(port->dev, "can't remap port#%d\n", port->line);

drivers/tty/serial/sh-sci.c static int __init hscif_early_console_setup(struct earlycon_device *device, · line 3552

Quoted 10 lines
drivers/tty/serial/sh-sci.c +2 -2
@@ -3545,8 +3545,8 @@ static int __init hscif_early_console_setup(struct earlycon_device *device,
 
 OF_EARLYCON_DECLARE(sci, "renesas,sci", sci_early_console_setup);
 OF_EARLYCON_DECLARE(scif, "renesas,scif", scif_early_console_setup);
-OF_EARLYCON_DECLARE(scif, "renesas,scif-r7s9210", rzscifa_early_console_setup);
-OF_EARLYCON_DECLARE(scif, "renesas,scif-r9a07g044", rzscifa_early_console_setup);
+OF_EARLYCON_DECLARE(rzscifa, "renesas,scif-r7s9210", rzscifa_early_console_setup);
+OF_EARLYCON_DECLARE(rzscifa, "renesas,scif-r9a07g044", rzscifa_early_console_setup);
 OF_EARLYCON_DECLARE(scifa, "renesas,scifa", scifa_early_console_setup);
 OF_EARLYCON_DECLARE(scifb, "renesas,scifb", scifb_early_console_setup);
 OF_EARLYCON_DECLARE(hscif, "renesas,hscif", hscif_early_console_setup);

Gr{oetje,eeting}s,

Geert

Signature · 5 lines
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds
author maintainer
#13 lore raw

PATCH v7 20/36 dt-bindings: serial: renesas,scif: Add scif-sh7751.

In reply to a message not in the archive

Add Renesas SH7751 SCIF.

---
 Documentation/devicetree/bindings/serial/renesas,scif.yaml | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/serial/renesas,scif.yaml +1 -0
index 4610a5bd580c..590f88e2ced9 100644
@@ -18,6 +18,7 @@ properties:
       - items:
           - enum:
               - renesas,scif-r7s72100     # RZ/A1H
+              - renesas,scif-sh7751       # SH7751
           - const: renesas,scif           # generic SCIF compatible UART
 
       - items:
Signature · 1 line
2.39.2
author maintainer
#14 lore raw

PATCH v7 21/36 dt-bindings: display: smi,sm501: SMI SM501 binding json-schema

In reply to a message not in the archive
---
 .../bindings/display/smi,sm501.yaml           | 398 ++++++++++++++++++
 1 file changed, 398 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/smi,sm501.yaml
Documentation/devicetree/bindings/display/smi,sm501.yaml new file +398 -0
new file mode 100644
index 000000000000..06c6af4fa4a9
@@ -0,0 +1,398 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/smi,sm501.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Silicon Motion SM501 Mobile Multimedia Companion Chip
+
+maintainers:
+  - Yoshinori Sato <[email protected]>
+
+description: |
+  These DT bindings describe the SM501.
+
+properties:
+  compatible:
+    const:
+      smi,sm501
+
+  reg:
+    maxItems: 2
+    description: |
+     First entry: System Configuration register
+     Second entry: IO space (Display Controller register)
+
+  interrupts:
+    description: SM501 interrupt to the cpu should be described here.
+
+  mode:
+    $ref: /schemas/types.yaml#/definitions/string
+    description: select a video mode
+
+  edid:
+    description: |
+      verbatim EDID data block describing attached display.
+      Data from the detailed timing descriptor will be used to
+      program the display controller.
+
+  little-endian:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: available on big endian systems, to set different foreign endian.
+  big-endian:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: available on little endian systems, to set different foreign endian.
+
+  swap-fb-endian:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: swap framebuffer byteorder.
+
+  route-crt-panel:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: Panel output merge to CRT.
+
+  crt:
+    type: object
+    description: CRT output control
+    properties:
+      edid:
+        $ref: /schemas/types.yaml#/definitions/uint8-array
+        description: |
+          verbatim EDID data block describing attached display.
+          Data from the detailed timing descriptor will be used to
+          program the display controller.
+
+      smi,flags:
+        $ref: /schemas/types.yaml#/definitions/string-array
+        description: Display control flags.
+        items:
+          anyOf:
+            - const: use-init-done
+            - const: disable-at-exit
+            - const: use-hwcursor
+            - const: use-hwaccel
+            - const: panel-no-fpen
+            - const: panel-no-vbiasen
+            - const: panel-inv-fpen
+            - const: panel-inv-vbiasen
+        maxItems: 8
+
+      bpp:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Color depth
+
+  panel:
+    type: object
+    description: Panel output control
+    properties:
+      edid:
+        $ref: /schemas/types.yaml#/definitions/uint8-array
+        description: |
+          verbatim EDID data block describing attached display.
+          Data from the detailed timing descriptor will be used to
+          program the display controller.
+
+      smi,flags:
+        $ref: /schemas/types.yaml#/definitions/string-array
+        description: Display control flags.
+        items:
+          anyOf:
+            - const: use-init-done
+            - const: disable-at-exit
+            - const: use-hwcursor
+            - const: use-hwaccel
+            - const: panel-no-fpen
+            - const: panel-no-vbiasen
+            - const: panel-inv-fpen
+            - const: panel-inv-vbiasen
+        maxItems: 8
+
+      bpp:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Color depth
+
+  smi,devices:
+    $ref: /schemas/types.yaml#/definitions/string-array
+    description: Select SM501 device functions.
+    items:
+      anyOf:
+        - const: usb-host
+        - const: usb-slave
+        - const: ssp0
+        - const: ssp1
+        - const: uart0
+        - const: uart1
+        - const: fbaccel
+        - const: ac97
+        - const: i2s
+        - const: gpio
+    minItems: 1
+    maxItems: 10
+
+  smi,mclk:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: mclk frequency.
+
+  smi,m1xclk:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: m1xclk frequency.
+
+  misc-timing:
+    type: object
+    description: Miscellaneous Timing register values.
+    properties:
+      ex:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Extend bus holding time.
+
+      xc:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Xscale clock input select.
+
+      usb-over-current-detect-disable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB host current detection disable (Us=0).
+
+      usb-over-current-detect-enable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB host current detection disable (Us=1).
+
+      sdram-clock-mode1-288mhz:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SSM1 bit is clear.
+
+      sdram-clock-mode1-div:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SSM1 bit is set.
+
+      sm1:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SDRAM clock divider for PW mode 1.
+
+      sdram-clock-mode0-288mhz:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SSM0 bit is clear.
+
+      sdram-clock-mode0-div:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SSM0 bit is set.
+
+      sm0:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: SDRAM clock divider for PW mode 0.
+
+      pll-debug-input:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: 96MHz PLL debug input reference frequency (Deb=0).
+
+      pll-debug-output:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: 96MHz PLL debug output frequency (Deb=1).
+
+      no-acpi-control:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: No ACPI control (A=0).
+
+      acpi-control:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: No ACPI control (A=1).
+
+      divider:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Second PLL output frequency.
+
+      usb-host-normal:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB Host normal mode.
+
+      usb-host-simulation:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB Host simulation mode.
+
+      delay:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Delay time to latch read data. Set the value to 10x.
+
+  misc-control:
+    type: object
+    description: Miscellaneous Control register values.
+    properties:
+      pad:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: PCI Pad drive strength.
+
+      usbclk:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: USB Clcok Select.
+
+      uart1:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: UART1 (SSP=0)
+
+      ssp1:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SSP1 (SSP=1)
+
+      latch-address-disable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: 8051 Latch disable (Lat=0).
+
+      latch-address-enable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: 8051 Latch enable (Lat=1).
+
+      panel-data-18bit:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: Flat Panel data 18bit (FP=0).
+
+      panel-data-24bit:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: Flat Panel data 24bit (FP=1).
+
+      xtal-freq-24mhz:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: Crystal frequency 24MHz (Freq=0).
+
+      xtal-freq-12mhz:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: Crystal frequency 12MHz (Freq=1).
+
+      refresh:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: Internal memory refresh timing.
+
+      hold:
+        $ref: /schemas/types.yaml#/definitions/uint32
+        description: BUS Hold time.
+
+      sh-ready-low:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SuperH ready polarity active low (SH=0).
+
+      sh-ready-high:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: SuperH ready polarity active high (SH=1).
+
+      interrupt-normal:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: Interrupt normal (II=0).
+
+      interrupt-inverted:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: Interrupt Inverting (II=1).
+
+      pll-clock-count-disable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: PLL clock count disable.
+
+      pll-clock-count-enaable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: PLL clock count enable.
+
+      dac-power-enable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: DAC Power enable (DAC=0).
+
+      dac-power-disable:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: DAC Power disable (DAC=1).
+
+      usb-slave-cpu:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB slave controller cpu (MC=0).
+
+      usb-slave-8051:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB slave controller 8051MCU (MC=1).
+
+      burst-length-8:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: CPU Master burst length 8 (BL=0).
+
+      burst-length-1:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: CPU Master burst length 1 (BL=1).
+
+      usb-port-master:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB port master.
+
+      usb-port-slave:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: USB port slave.
+
+      vr-mmio-30mb:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: NEC VR Memory map MMIO locatedat 30MB (VR=0)
+
+      vr-mmio-62mb:
+        $ref: /schemas/types.yaml#/definitions/flag
+        description: NEC VR Memory map MMIO locatedat 62MB (VR=1)
+
+  gpio-pin-control:
+    type: object
+    description: GPIO control configuration.
+    properties:
+      pin:
+        type: object
+        properties:
+          gpio:
+            $ref: /schemas/types.yaml#/definitions/flag
+            description: pin in/out use GPIO.
+          function:
+            $ref: /schemas/types.yaml#/definitions/flag
+            description: pin in/out use function.
+
+  gpio-i2c:
+    type: object
+    description: GPIO I2C definition.
+    properties:
+      i2c:
+        type: object
+        properties:
+          bus:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: I2C bus number.
+
+          sda:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: I2C SDA pin port number.
+
+          scl:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: I2C SCL pin port number.
+
+          delay:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: bit transmission delay.
+
+          timeout:
+            $ref: /schemas/types.yaml#/definitions/uint32
+            description: transmission timeout.
+
+additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+
+examples:
+  # MPC5200
+  - |
+    display@1,0 {
+        compatible = "smi,sm501";
+        reg = <0x00000000 0x00800000
+               0x03e00000 0x00200000>;
+        interrupts = <1 1 3>;
+        mode = "640x480-32@60";
+        edid = [00 ff ff ff ff ff ff 00 00 00 00 00 00 00 00 00
+                00 00 01 04 00 00 00 00 00 00 00 00 00 00 00 00
+                00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+                00 00 00 00 00 00 f0 0a 80 fb 20 e0 25 10 32 60
+                02 00 00 00 00 00 00 06 00 00 00 00 00 00 00 00
+                00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+                00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+                00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 bd];
+    };
Signature · 1 line
2.39.2
author maintainer
#15 lore raw

PATCH v7 22/36 dt-bindings: display: sm501 register definition helper

In reply to a message not in the archive

Miscellaneous Timing and Miscellaneous Control registers definition.

---
 include/dt-bindings/display/sm501.h | 76 +++++++++++++++++++++++++++++
 1 file changed, 76 insertions(+)
 create mode 100644 include/dt-bindings/display/sm501.h
include/dt-bindings/display/sm501.h new file +76 -0
new file mode 100644
index 000000000000..a6c6943642e4
@@ -0,0 +1,76 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause */
+#ifndef __DT_BINDING_DISPALY_SM501__
+#define __DT_BINDING_DISPALY_SM501__
+
+/* Miscellaneous Conntrol */
+#define SM501_MISC_CONTROL_PAD_24	0
+#define SM501_MISC_CONTROL_PAD_12	1
+#define SM501_MISC_CONTROL_PAD_8	2
+
+#define SM501_MISC_CONTROL_USBCLK_XTAL	0
+#define SM501_MISC_CONTROL_USBCLK_96MHZ	1
+#define SM501_MISC_CONTROL_USBCLK_48MHZ	2
+
+#define SM501_MISC_CONTROL_RFSH_8US	0
+#define SM501_MISC_CONTROL_RFSH_16US	1
+#define SM501_MISC_CONTROL_RFSH_32US	2
+#define SM501_MISC_CONTROL_RFSH_64US	3
+
+#define SM501_MISC_CONTROL_HOLD_EMPTY	0
+#define SM501_MISC_CONTROL_HOLD_8TR	1
+#define SM501_MISC_CONTROL_HOLD_16TR	2
+#define SM501_MISC_CONTROL_HOLD_24TR	3
+#define SM501_MISC_CONTROL_HOLD_32TR	4
+
+/* Miscellaneous timing */
+#define SM501_MISC_TIMING_EX_HOLD_0	0
+#define SM501_MISC_TIMING_EX_HOLD_16	1
+#define SM501_MISC_TIMING_EX_HOLD_32	2
+#define SM501_MISC_TIMING_EX_HOLD_48	3
+#define SM501_MISC_TIMING_EX_HOLD_64	4
+#define SM501_MISC_TIMING_EX_HOLD_80	5
+#define SM501_MISC_TIMING_EX_HOLD_96	6
+#define SM501_MISC_TIMING_EX_HOLD_112	7
+#define SM501_MISC_TIMING_EX_HOLD_128	8
+#define SM501_MISC_TIMING_EX_HOLD_144	9
+#define SM501_MISC_TIMING_EX_HOLD_160	10
+#define SM501_MISC_TIMING_EX_HOLD_176	11
+#define SM501_MISC_TIMING_EX_HOLD_192	12
+#define SM501_MISC_TIMING_EX_HOLD_208	13
+#define SM501_MISC_TIMING_EX_HOLD_224	14
+#define SM501_MISC_TIMING_EX_HOLD_240	15
+
+#define SM501_MISC_TIMING_XC_INTERNAL	0
+#define SM501_MISC_TIMING_XC_HCLK	1
+#define SM501_MISC_TIMING_XC_GPIO	2
+
+#define SM501_MISC_TIMING_SM_DIV1	0
+#define SM501_MISC_TIMING_SM_DIV2	1
+#define SM501_MISC_TIMING_SM_DIV4	2
+#define SM501_MISC_TIMING_SM_DIV8	3
+#define SM501_MISC_TIMING_SM_DIV16	4
+#define SM501_MISC_TIMING_SM_DIV32	5
+#define SM501_MISC_TIMING_SM_DIV64	6
+#define SM501_MISC_TIMING_SM_DIV128	7
+#define SM501_MISC_TIMING_SM_DIV3	8
+#define SM501_MISC_TIMING_SM_DIV6	9
+#define SM501_MISC_TIMING_SM_DIV12	10
+#define SM501_MISC_TIMING_SM_DIV24	11
+#define SM501_MISC_TIMING_SM_DIV48	12
+#define SM501_MISC_TIMING_SM_DIV96	13
+#define SM501_MISC_TIMING_SM_DIV192	14
+#define SM501_MISC_TIMING_SM_DIV384	15
+
+#define SM501_MISC_TIMING_DIV336MHZ	0
+#define SM501_MISC_TIMING_DIV288MHZ	1
+#define SM501_MISC_TIMING_DIV240MHZ	2
+#define SM501_MISC_TIMING_DIV192MHZ	3
+
+#define SM501_MISC_TIMING_DELAY_NONE	0
+#define SM501_MISC_TIMING_DELAY_0_5	1
+#define SM501_MISC_TIMING_DELAY_1_0	2
+#define SM501_MISC_TIMING_DELAY_1_5	3
+#define SM501_MISC_TIMING_DELAY_2_0	4
+#define SM501_MISC_TIMING_DELAY_2_5	5
+
+#endif
Signature · 1 line
2.39.2
author maintainer
#16 lore raw

PATCH v7 23/36 mfd: sm501: Convert platform_data to OF property

In reply to a message not in the archive

Various parameters of SM501 can be set using platform_data, so parameters cannot be passed in the DeviceTree target. Expands the parameters set in platform_data so that they can be specified using DeviceTree properties.

---
 drivers/mfd/sm501.c           | 315 ++++++++++++++++++++++++++++++++++
 drivers/video/fbdev/sm501fb.c | 106 ++++++++++++
 2 files changed, 421 insertions(+)
drivers/mfd/sm501.c +315 -0
index b3592982a83b..98a69e254f5f 100644
@@ -82,6 +82,16 @@ struct sm501_devdata {
 	unsigned int			 rev;
 };
 
+struct sm501_config_props_uint {
+	char *name;
+	u32 shift;
+};
+
+struct sm501_config_props_flag {
+	char *clr_name;
+	char *set_name;
+	u32 bit;
+};
 
 #define MHZ (1000 * 1000)
 
@@ -1370,6 +1380,305 @@ static int sm501_init_dev(struct sm501_devdata *sm)
 	return 0;
 }
 
+static const struct sm501_config_props_uint misc_timing[] = {
+	{"delay",    0},
+	{"-",        3},
+	{"divider",  4},
+	{"-",        6},
+	{"sm0",      8},
+	{"-",       12},
+	{"sm1",     16},
+	{"-",       20},
+	{"xc",      24},
+	{"-",       26},
+	{"ex",      28},
+	{NULL,      32},
+};
+
+static const struct sm501_config_props_flag misc_timing_flag[] = {
+	{"usb-host-normal",          "usb-host-simulation",    3},
+	{"no-acpi-control",          "acpi-control",           6},
+	{"pll-debug-input",          "pll-debug-output",       7},
+	{"sdram-clock-mode0-288mhz", "sdram-clock-mode0-div", 12},
+	{"sdram-clock-mode1-288mhz", "sdram-clock-mode1-div", 20},
+	{"usb-over-current-detect-disable",
+	 "usb-over-current-detect-enable",  23},
+	{},
+};
+
+static const struct sm501_config_props_uint misc_control[] = {
+	{"hold",     18},
+	{"refresh",  21},
+	{"-",        23},
+	{"usbclk",   28},
+	{"pad",      30},
+	{NULL,       32},
+};
+
+static const struct sm501_config_props_flag misc_control_flag[] = {
+	{"vr-mmio-30mb",            "vr-mmio-62mb",             4},
+	{"usb-port-master",         "usb-port-slave",           9},
+	{"burst-length-8",          "burst-length-1",          10},
+	{"usb-slave-cpu",           "usb-slave-8051",          11},
+	{"dac-power-enable",        "dac-power-disable",       12},
+	{"pll-clock-count-disable", "pll-clock-count-enable",  15},
+	{"interrupt-normal",        "interrupt-invarted",      16},
+	{"sh-ready-low",            "sh-ready-high",           17},
+	{"xtal-freq-24mhz",         "xtal-freq-12mhz",         24},
+	{"panel-data-18bit",        "panel-dtat-24bit",        25},
+	{"latch-address-disable",   "latch-address-enable",    26},
+	{"uart1",                   "ssp1",                    27},
+	{},
+};
+
+/* Read configuration values */
+static void sm501_of_read_config(struct device *dev, struct device_node *np,
+				 const char *prefix,
+				 const struct sm501_config_props_uint *props,
+				 const struct sm501_config_props_flag *props_flag,
+				 struct sm501_reg_init *ret)
+{
+	struct device_node *child;
+	char *name;
+	u32 shift;
+	u32 width;
+	u32 mask;
+	u32 val;
+
+	ret->mask = ~0;
+	ret->set = 0;
+
+	child = of_get_child_by_name(np, prefix);
+	if (!child)
+		return;
+
+	while (props->name) {
+		name = props->name;
+		shift = props->shift;
+		props++;
+
+		if (name[0] == '-' ||
+		    of_property_read_u32(child, name, &val))
+			continue;
+
+		width = props->shift - shift;
+		mask = (1 << width) - 1;
+		if (mask < val) {
+			dev_warn(dev, "%s invalid value %d", name, val);
+			continue;
+		}
+		mask = ~(mask << shift);
+		ret->mask &= mask;
+		ret->set |= val << shift;
+	}
+	while (props_flag->clr_name) {
+		val = ~0;
+		if (of_property_read_bool(child, props_flag->clr_name))
+			val = 0;
+		else if (of_property_read_bool(child, props_flag->set_name))
+			val = 1;
+		if (val != ~0) {
+			val <<= (props_flag->bit & 31);
+			mask = 1 << (props_flag->bit & 31);
+			ret->mask &= ~mask;
+			ret->set |= val;
+		}
+		props_flag++;
+	}
+}
+
+/* Read GPIO control */
+/*
+ * DT example.
+ * gpio-pin-control {
+ *   pin@0 {
+ *	 gpio-port;
+ *   };
+ *   pin@1 {
+ *	 function;
+ *   };
+ * };
+ */
+static void sm501_of_read_gpio(struct device *dev, struct device_node *np,
+			       struct sm501_reg_init *hi, struct sm501_reg_init *low)
+{
+	struct device_node *gpio_group, *pin;
+	const char *prop_mode;
+	unsigned int pin_no;
+	int mode;
+	u64 mask;
+	u64 set;
+
+	mask = ~0;
+	set = 0;
+	gpio_group = of_get_child_by_name(np, "gpio-pin-control");
+	if (gpio_group) {
+		for_each_child_of_node(gpio_group, pin) {
+			mode = -1;
+			if (sscanf(pin->full_name, "pin@%u", &pin_no) == 1) {
+				if (of_property_read_bool(pin, "gpio-port"))
+					mode = 0;
+				else if (of_property_read_bool(pin, "function"))
+					mode = 1;
+			}
+			/* GPIO0 - 47 and 55 -63 */
+			if (mode < 0 ||
+			    (pin_no >= 64 || (pin_no >= 48 && pin_no <= 54))) {
+				dev_warn(dev,
+					 "%s mode %s is invalid.", pin->name, prop_mode);
+			} else {
+				mask &= ~(1 << pin_no);
+				set |= mode << pin_no;
+			}
+		}
+	}
+	hi->set = set >> 32;
+	low->set = set & 0xffffffff;
+	hi->mask = mask >> 32;
+	low->mask = mask & 0xffffffff;
+}
+
+static inline int read_i2c_prop(struct device *dev, struct device_node *child,
+				const char *name, u32 *val)
+{
+	if (of_property_read_u32(child, name, val)) {
+		dev_warn(dev, "%s/%s not found. skip it.", of_node_full_name(child), name);
+		return -ENOENT;
+	}
+	return 0;
+}
+
+/* Read GPIO I2C configuration */
+/*
+ * DT example.
+ * gpio-i2c {
+ *    i2c@0 {
+ *	sda = <gpio-pin>;
+ *	scl = <gpio-pin>;
+ *	delay = <delay>;
+ *	timeout = <timeout>;
+ *    };
+ *    i2c@1 {
+ *      :
+ *    };
+ *    :
+ * };
+ */
+static int sm501_parse_dt_gpio_i2c(struct device *dev, struct sm501_platdata *plat,
+				   struct device_node *np)
+{
+	struct device_node *i2c_group, *child;
+	unsigned int i;
+	u32 i2c_nr;
+	int err;
+
+	i2c_group = of_get_child_by_name(np, "gpio-i2c");
+	if (!i2c_group)
+		return 0;
+
+	i2c_nr = of_get_child_count(i2c_group);
+	plat->gpio_i2c = devm_kzalloc(dev, sizeof(*plat->gpio_i2c) * i2c_nr,
+				      GFP_KERNEL);
+	if (!plat->gpio_i2c)
+		return -ENOMEM;
+
+	plat->gpio_i2c_nr = i2c_nr;
+	i = 0;
+	for_each_child_of_node(i2c_group, child) {
+		u32 bus;
+
+		if (sscanf(child->full_name, "i2c@%u", &bus) != 1) {
+			dev_warn(dev, "Unknown address %s\n", child->name);
+			continue;
+		}
+
+		err = 0;
+		plat->gpio_i2c[i].bus_num = bus;
+		err += read_i2c_prop(dev, child, "sda", &plat->gpio_i2c[i].pin_sda);
+		err += read_i2c_prop(dev, child, "scl", &plat->gpio_i2c[i].pin_scl);
+		err += read_i2c_prop(dev, child, "delay", &plat->gpio_i2c[i].udelay);
+		err += read_i2c_prop(dev, child, "timeout", &plat->gpio_i2c[i].timeout);
+		if (err == 0)
+			i++;
+	}
+
+	return 0;
+}
+
+/* Read device functions */
+static u32 sm501_read_devices(struct device *dev, struct device_node *np)
+{
+	static const char * const funcname[] = {
+		"usb-host", "usb-slave", "ssp0", "ssp1",
+		"uart0", "uart1", "fbaccel", "ac97",
+		"i2s", "gpio",
+	};
+	struct property *prop;
+	unsigned int i;
+	const char *s;
+	u32 ret = 0;
+
+	of_property_for_each_string(np, "smi,devices", prop, s) {
+		for (i = 0; i < ARRAY_SIZE(funcname); i++) {
+			if (strcmp(s, funcname[i]) == 0) {
+				ret |= 1 << i;
+				goto next;
+			}
+		}
+		dev_warn(dev, "Unknown device function '%s'", s);
+next:
+	}
+	if (!ret)
+		dev_warn(dev, "devices not defined. disable all functions.");
+	return ret;
+}
+
+/* Build platform_data from OF property */
+struct plat_dt {
+	struct sm501_platdata plat;
+	struct sm501_initdata init;
+};
+
+static int sm501_parse_dt(struct sm501_devdata *sm, struct device_node *np)
+{
+	struct sm501_platdata *plat;
+	struct plat_dt *dt_p;
+	u32 word;
+	int ret;
+
+	dt_p = devm_kzalloc(sm->dev, sizeof(*dt_p), GFP_KERNEL);
+	if (!dt_p)
+		return -ENOMEM;
+
+	plat = &dt_p->plat;
+	plat->init = &dt_p->init;
+
+	plat->init->devices = sm501_read_devices(sm->dev, np);
+	/* mclk and m1xclk are not u32, so convert between them using intermediate variables. */
+	of_property_read_u32(np, "smi,mclk", &word);
+	plat->init->mclk = word;
+	of_property_read_u32(np, "smi,m1xclk", &word);
+	plat->init->m1xclk = word;
+
+	sm501_of_read_config(sm->dev, np, "misc-timing",
+			     misc_timing, misc_timing_flag,
+			     &plat->init->misc_timing);
+	sm501_of_read_config(sm->dev, np, "misc-control",
+			     misc_control, misc_control_flag,
+			     &plat->init->misc_control);
+	sm501_of_read_gpio(sm->dev, np,
+			   &plat->init->gpio_high, &plat->init->gpio_low);
+
+	if (IS_ENABLED(CONFIG_MFD_SM501_GPIO) &&
+	    (plat->init->devices & SM501_USE_GPIO)) {
+		ret = sm501_parse_dt_gpio_i2c(sm->dev, plat, np);
+		if (ret)
+			return ret;
+	}
+	sm->platdata = plat;
+	return 0;
+}
+
 static int sm501_plat_probe(struct platform_device *dev)
 {
 	struct sm501_devdata *sm;
@@ -1406,6 +1715,12 @@ static int sm501_plat_probe(struct platform_device *dev)
 		goto err_res;
 	}
 
+	if (IS_ENABLED(CONFIG_OF) && dev->dev.of_node) {
+		ret = sm501_parse_dt(sm, dev->dev.of_node);
+		if (ret)
+			goto err_res;
+	}
+
 	platform_set_drvdata(dev, sm);
 
 	sm->regs = ioremap(sm->io_res->start, resource_size(sm->io_res));
drivers/video/fbdev/sm501fb.c +106 -0

118 lines not on this page · raw message

Signature · 1 line
2.39.2
author maintainer
#17 lore raw

PATCH v7 24/36 dt-binding: sh: cpus: Add SH CPUs json-schema

In reply to a message not in the archive

Renesas SH series and compatible ISA CPUs.

---
 .../devicetree/bindings/sh/cpus.yaml          | 61 +++++++++++++++++++
 1 file changed, 61 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sh/cpus.yaml
Documentation/devicetree/bindings/sh/cpus.yaml new file +61 -0
new file mode 100644
index 000000000000..43e079b8753d
@@ -0,0 +1,61 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/sh/cpus.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas SuperH CPUs
+
+maintainers:
+  - Yoshinori Sato <[email protected]>
+
+description: |+
+  Definition of CPU core with Renesas SuperH and compatible instruction set.
+
+properties:
+  compatible:
+    anyOf:
+      - items:
+          - enum:
+              - renesas,sh2a
+              - renesas,sh3
+              - renesas,sh4
+              - renesas,sh4a
+              - jcore,j2
+          - const: renesas,sh2
+      - const: renesas,sh2
+
+  clocks:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+  device_type: true
+
+required:
+  - compatible
+  - reg
+  - device_type
+
+
+examples:
+  - |
+    #include <dt-bindings/clock/sh7750-cpg.h>
+    cpus {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        cpu: cpu@0 {
+            compatible = "renesas,sh4", "renesas,sh2";
+            device_type = "cpu";
+            reg = <0>;
+            clocks = <&cpg SH7750_CPG_ICK>;
+            clock-names = "ick";
+            icache-size = <16384>;
+            icache-line-size = <32>;
+            dcache-size = <32768>;
+            dcache-line-size = <32>;
+        };
+    };
+...
Signature · 1 line
2.39.2