Skip to contentSkip to conversation

net: phy: realtek: various improvements for 2.5GE PHYs

PATCH Applied Daniel Golle 4 participants 11 messages Jan 5 – Jan 8

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

v2 cover net: phy: realtek: various improvements for 2.5GE PHYs

This series improves the RealTek PHY driver, mostly for 2.5GE PHYs. It implements configuring SGMII and 2500Base-X in-band auto-negotiation and improves using the PHYs in Clause-22-only mode.

Note that the rtl822x_serdes_write() function introduced by this series is going to be reused to configure polarities of SerDes RX and TX lanes once series "PHY polarity inversion via generic device tree properties" has been applied.

Access to other registers on MDIO_MMD_VEND2 is important for more than just configuring autonegotiation, it is also used to setup ALDPS or to disable the PHY responding to the MDIO broadcast address 0. Both will be implemented by follow-up patches.

The address translation function for registers on MDIO_MMD_VEND2 into paged registers can potentially also be used to describe other paged access in a more consistent way, but that mostly makes sense on PHYs which also support Clause-45, so this series doesn't convert all the existing paged access on RealTek's 1GE PHYs which do not support Clause-45.
---
Changes since initial submission:
- use mmd_phy_read and mmd_phy_write
- fix return value in on error (oldpage vs. ret)
- fix wrong parameter name (reg vs. mmdreg)

Daniel Golle (5):
net: phy: realtek: fix whitespace in struct phy_driver initializers
net: phy: realtek: implement configuring in-band an
net: phy: move mmd_phy_read and mmd_phy_write to phylib.h
net: phy: realtek: use paged access for MDIO_MMD_VEND2 in C22 mode
net: phy: realtek: get rid of magic number in rtlgen_read_status()

 drivers/net/phy/phylib-internal.h      |   6 -
 drivers/net/phy/phylib.h               |   5 +
 drivers/net/phy/realtek/realtek_main.c | 307 ++++++++++++++++++-------
 3 files changed, 235 insertions(+), 83 deletions(-)
Signature · 1 line
2.52.0
#1 lore raw

PATCH v2 1/5 net: phy: realtek: fix whitespace in struct phy_driver initializers

Consistently use tabs instead of spaces in struct phy_driver initializers.

---
v2: no changes

 drivers/net/phy/realtek/realtek_main.c | 146 ++++++++++++-------------
 1 file changed, 73 insertions(+), 73 deletions(-)
drivers/net/phy/realtek/realtek_main.c +73 -73
index 6ff0385201a57..e42c5efbfa5ef 100644
@@ -1976,7 +1976,7 @@ static irqreturn_t rtl8221b_handle_interrupt(struct phy_device *phydev)
 static struct phy_driver realtek_drvs[] = {
 	{
 		PHY_ID_MATCH_EXACT(0x00008201),
-		.name           = "RTL8201CP Ethernet",
+		.name		= "RTL8201CP Ethernet",
 		.read_page	= rtl821x_read_page,
 		.write_page	= rtl821x_write_page,
 	}, {
@@ -2102,7 +2102,7 @@ static struct phy_driver realtek_drvs[] = {
 		.name		= "RTL8226B_RTL8221B 2.5Gbps PHY",
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
-		.config_init    = rtl822xb_config_init,
+		.config_init	= rtl822xb_config_init,
 		.get_rate_matching = rtl822xb_get_rate_matching,
 		.read_status	= rtl822xb_read_status,
 		.suspend	= genphy_suspend,
@@ -2111,112 +2111,112 @@ static struct phy_driver realtek_drvs[] = {
 		.write_page	= rtl821x_write_page,
 	}, {
 		PHY_ID_MATCH_EXACT(0x001cc838),
-		.name           = "RTL8226-CG 2.5Gbps PHY",
-		.soft_reset     = rtl822x_c45_soft_reset,
-		.get_features   = rtl822x_c45_get_features,
-		.config_aneg    = rtl822x_c45_config_aneg,
-		.config_init    = rtl822x_config_init,
-		.read_status    = rtl822xb_c45_read_status,
-		.suspend        = genphy_c45_pma_suspend,
-		.resume         = rtlgen_c45_resume,
+		.name		= "RTL8226-CG 2.5Gbps PHY",
+		.soft_reset	= rtl822x_c45_soft_reset,
+		.get_features	= rtl822x_c45_get_features,
+		.config_aneg	= rtl822x_c45_config_aneg,
+		.config_init	= rtl822x_config_init,
+		.read_status	= rtl822xb_c45_read_status,
+		.suspend	= genphy_c45_pma_suspend,
+		.resume		= rtlgen_c45_resume,
 	}, {
 		PHY_ID_MATCH_EXACT(0x001cc848),
-		.name           = "RTL8226B-CG_RTL8221B-CG 2.5Gbps PHY",
-		.get_features   = rtl822x_get_features,
-		.config_aneg    = rtl822x_config_aneg,
-		.config_init    = rtl822xb_config_init,
+		.name		= "RTL8226B-CG_RTL8221B-CG 2.5Gbps PHY",
+		.get_features	= rtl822x_get_features,
+		.config_aneg	= rtl822x_config_aneg,
+		.config_init	= rtl822xb_config_init,
 		.get_rate_matching = rtl822xb_get_rate_matching,
-		.read_status    = rtl822xb_read_status,
-		.suspend        = genphy_suspend,
-		.resume         = rtlgen_resume,
-		.read_page      = rtl821x_read_page,
-		.write_page     = rtl821x_write_page,
+		.read_status	= rtl822xb_read_status,
+		.suspend	= genphy_suspend,
+		.resume		= rtlgen_resume,
+		.read_page	= rtl821x_read_page,
+		.write_page	= rtl821x_write_page,
 	}, {
 		.match_phy_device = rtl8221b_vb_cg_c22_match_phy_device,
-		.name           = "RTL8221B-VB-CG 2.5Gbps PHY (C22)",
+		.name		= "RTL8221B-VB-CG 2.5Gbps PHY (C22)",
 		.probe		= rtl822x_probe,
-		.get_features   = rtl822x_get_features,
-		.config_aneg    = rtl822x_config_aneg,
-		.config_init    = rtl822xb_config_init,
+		.get_features	= rtl822x_get_features,
+		.config_aneg	= rtl822x_config_aneg,
+		.config_init	= rtl822xb_config_init,
 		.get_rate_matching = rtl822xb_get_rate_matching,
-		.read_status    = rtl822xb_read_status,
-		.suspend        = genphy_suspend,
-		.resume         = rtlgen_resume,
-		.read_page      = rtl821x_read_page,
-		.write_page     = rtl821x_write_page,
+		.read_status	= rtl822xb_read_status,
+		.suspend	= genphy_suspend,
+		.resume		= rtlgen_resume,
+		.read_page	= rtl821x_read_page,
+		.write_page	= rtl821x_write_page,
 	}, {
 		.match_phy_device = rtl8221b_vb_cg_c45_match_phy_device,
-		.name           = "RTL8221B-VB-CG 2.5Gbps PHY (C45)",
+		.name		= "RTL8221B-VB-CG 2.5Gbps PHY (C45)",
 		.config_intr	= rtl8221b_config_intr,
 		.handle_interrupt = rtl8221b_handle_interrupt,
 		.probe		= rtl822x_probe,
-		.config_init    = rtl822xb_config_init,
+		.config_init	= rtl822xb_config_init,
 		.get_rate_matching = rtl822xb_get_rate_matching,
-		.get_features   = rtl822x_c45_get_features,
-		.config_aneg    = rtl822x_c45_config_aneg,
-		.read_status    = rtl822xb_c45_read_status,
-		.suspend        = genphy_c45_pma_suspend,
-		.resume         = rtlgen_c45_resume,
+		.get_features	= rtl822x_c45_get_features,
+		.config_aneg	= rtl822x_c45_config_aneg,
+		.read_status	= rtl822xb_c45_read_status,
+		.suspend	= genphy_c45_pma_suspend,
+		.resume		= rtlgen_c45_resume,
 	}, {
 		.match_phy_device = rtl8221b_vm_cg_c22_match_phy_device,
-		.name           = "RTL8221B-VM-CG 2.5Gbps PHY (C22)",
+		.name		= "RTL8221B-VM-CG 2.5Gbps PHY (C22)",
 		.probe		= rtl822x_probe,
-		.get_features   = rtl822x_get_features,
-		.config_aneg    = rtl822x_config_aneg,
-		.config_init    = rtl822xb_config_init,
+		.get_features	= rtl822x_get_features,
+		.config_aneg	= rtl822x_config_aneg,
+		.config_init	= rtl822xb_config_init,
 		.get_rate_matching = rtl822xb_get_rate_matching,
-		.read_status    = rtl822xb_read_status,
-		.suspend        = genphy_suspend,
-		.resume         = rtlgen_resume,
-		.read_page      = rtl821x_read_page,
-		.write_page     = rtl821x_write_page,
+		.read_status	= rtl822xb_read_status,
+		.suspend	= genphy_suspend,
+		.resume		= rtlgen_resume,
+		.read_page	= rtl821x_read_page,
+		.write_page	= rtl821x_write_page,
 	}, {
 		.match_phy_device = rtl8221b_vm_cg_c45_match_phy_device,
-		.name           = "RTL8221B-VM-CG 2.5Gbps PHY (C45)",
+		.name		= "RTL8221B-VM-CG 2.5Gbps PHY (C45)",
 		.config_intr	= rtl8221b_config_intr,
 		.handle_interrupt = rtl8221b_handle_interrupt,
 		.probe		= rtl822x_probe,
-		.config_init    = rtl822xb_config_init,
+		.config_init	= rtl822xb_config_init,
 		.get_rate_matching = rtl822xb_get_rate_matching,
-		.get_features   = rtl822x_c45_get_features,
-		.config_aneg    = rtl822x_c45_config_aneg,
-		.read_status    = rtl822xb_c45_read_status,
-		.suspend        = genphy_c45_pma_suspend,
-		.resume         = rtlgen_c45_resume,
+		.get_features	= rtl822x_c45_get_features,
+		.config_aneg	= rtl822x_c45_config_aneg,
+		.read_status	= rtl822xb_c45_read_status,
+		.suspend	= genphy_c45_pma_suspend,
+		.resume		= rtlgen_c45_resume,
 	}, {
 		.match_phy_device = rtl8251b_c45_match_phy_device,
-		.name           = "RTL8251B 5Gbps PHY",
+		.name		= "RTL8251B 5Gbps PHY",
 		.probe		= rtl822x_probe,
-		.get_features   = rtl822x_get_features,
-		.config_aneg    = rtl822x_config_aneg,
-		.read_status    = rtl822x_read_status,
-		.suspend        = genphy_suspend,
-		.resume         = rtlgen_resume,
-		.read_page      = rtl821x_read_page,
-		.write_page     = rtl821x_write_page,
+		.get_features	= rtl822x_get_features,
+		.config_aneg	= rtl822x_config_aneg,
+		.read_status	= rtl822x_read_status,
+		.suspend	= genphy_suspend,
+		.resume		= rtlgen_resume,
+		.read_page	= rtl821x_read_page,
+		.write_page	= rtl821x_write_page,
 	}, {
 		.match_phy_device = rtl_internal_nbaset_match_phy_device,
-		.name           = "Realtek Internal NBASE-T PHY",
+		.name		= "Realtek Internal NBASE-T PHY",
 		.flags		= PHY_IS_INTERNAL,
 		.probe		= rtl822x_probe,
-		.get_features   = rtl822x_get_features,
-		.config_aneg    = rtl822x_config_aneg,
-		.read_status    = rtl822x_read_status,
-		.suspend        = genphy_suspend,
-		.resume         = rtlgen_resume,
-		.read_page      = rtl821x_read_page,
-		.write_page     = rtl821x_write_page,
+		.get_features	= rtl822x_get_features,
+		.config_aneg	= rtl822x_config_aneg,
+		.read_status	= rtl822x_read_status,
+		.suspend	= genphy_suspend,
+		.resume		= rtlgen_resume,
+		.read_page	= rtl821x_read_page,
+		.write_page	= rtl821x_write_page,
 		.read_mmd	= rtl822x_read_mmd,
 		.write_mmd	= rtl822x_write_mmd,
 	}, {
 		PHY_ID_MATCH_EXACT(0x001ccad0),
 		.name		= "RTL8224 2.5Gbps PHY",
 		.flags		= PHY_POLL_CABLE_TEST,
-		.get_features   = rtl822x_c45_get_features,
-		.config_aneg    = rtl822x_c45_config_aneg,
-		.read_status    = rtl822x_c45_read_status,
-		.suspend        = genphy_c45_pma_suspend,
-		.resume         = rtlgen_c45_resume,
+		.get_features	= rtl822x_c45_get_features,
+		.config_aneg	= rtl822x_c45_config_aneg,
+		.read_status	= rtl822x_c45_read_status,
+		.suspend	= genphy_c45_pma_suspend,
+		.resume		= rtlgen_c45_resume,
 		.cable_test_start = rtl8224_cable_test_start,
 		.cable_test_get_status = rtl8224_cable_test_get_status,
 	}, {
@@ -2235,7 +2235,7 @@ static struct phy_driver realtek_drvs[] = {
 	}, {
 		PHY_ID_MATCH_EXACT(0x001ccb00),
 		.name		= "RTL9000AA_RTL9000AN Ethernet",
-		.features       = PHY_BASIC_T1_FEATURES,
+		.features	= PHY_BASIC_T1_FEATURES,
 		.config_init	= rtl9000a_config_init,
 		.config_aneg	= rtl9000a_config_aneg,
 		.read_status	= rtl9000a_read_status,
Signature · 1 line
2.52.0
#3 lore raw

PATCH v2 2/5 net: phy: realtek: implement configuring in-band an

In reply to Daniel Golle

Implement the inband_caps() and config_inband() PHY driver methods to allow configuring the use of in-band-status with SGMII and 2500Base-X on RTL8226 and RTL8221B 2.5GE PHYs.

---
v2: no changes

 drivers/net/phy/realtek/realtek_main.c | 67 ++++++++++++++++++++++++++
 1 file changed, 67 insertions(+)
drivers/net/phy/realtek/realtek_main.c +67 -0
index e42c5efbfa5ef..0653a9d8fcb6f 100644
@@ -131,6 +131,15 @@
 #define RTL822X_VND1_SERDES_CTRL3_MODE_SGMII			0x02
 #define RTL822X_VND1_SERDES_CTRL3_MODE_2500BASEX		0x16
 
+#define RTL822X_VND1_SERDES_CMD			0x7587
+#define  RTL822X_VND1_SERDES_CMD_WRITE		BIT(1)
+#define  RTL822X_VND1_SERDES_CMD_BUSY		BIT(0)
+#define RTL822X_VND1_SERDES_ADDR		0x7588
+#define  RTL822X_VND1_SERDES_ADDR_AUTONEG	0x2
+#define   RTL822X_VND1_SERDES_INBAND_DISABLE	0x71d0
+#define   RTL822X_VND1_SERDES_INBAND_ENABLE	0x70d0
+#define RTL822X_VND1_SERDES_DATA		0x7589
+
 /* RTL822X_VND2_XXXXX registers are only accessible when phydev->is_c45
  * is set, they cannot be accessed by C45-over-C22.
  */
@@ -1308,6 +1317,50 @@ static int rtl822xb_config_init(struct phy_device *phydev)
 	return rtl822x_set_serdes_option_mode(phydev, false);
 }
 
+static int rtl822x_serdes_write(struct phy_device *phydev, u16 reg, u16 val)
+{
+	int ret, poll;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, RTL822X_VND1_SERDES_ADDR, reg);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, RTL822X_VND1_SERDES_DATA, val);
+	if (ret < 0)
+		return ret;
+
+	ret = phy_write_mmd(phydev, MDIO_MMD_VEND1, RTL822X_VND1_SERDES_CMD,
+			    RTL822X_VND1_SERDES_CMD_WRITE |
+			    RTL822X_VND1_SERDES_CMD_BUSY);
+	if (ret < 0)
+		return ret;
+
+	return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_VEND1,
+					 RTL822X_VND1_SERDES_CMD, poll,
+					 !(poll & RTL822X_VND1_SERDES_CMD_BUSY),
+					 500, 100000, false);
+}
+
+static int rtl822x_config_inband(struct phy_device *phydev, unsigned int modes)
+{
+	return rtl822x_serdes_write(phydev, RTL822X_VND1_SERDES_ADDR_AUTONEG,
+				    (modes != LINK_INBAND_DISABLE) ?
+				    RTL822X_VND1_SERDES_INBAND_ENABLE :
+				    RTL822X_VND1_SERDES_INBAND_DISABLE);
+}
+
+static unsigned int rtl822x_inband_caps(struct phy_device *phydev,
+					phy_interface_t interface)
+{
+	switch (interface) {
+	case PHY_INTERFACE_MODE_2500BASEX:
+	case PHY_INTERFACE_MODE_SGMII:
+		return LINK_INBAND_DISABLE | LINK_INBAND_ENABLE;
+	default:
+		return 0;
+	}
+}
+
 static int rtl822xb_get_rate_matching(struct phy_device *phydev,
 				      phy_interface_t iface)
 {
@@ -2103,6 +2156,8 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
 		.config_init	= rtl822xb_config_init,
+		.inband_caps	= rtl822x_inband_caps,
+		.config_inband	= rtl822x_config_inband,
 		.get_rate_matching = rtl822xb_get_rate_matching,
 		.read_status	= rtl822xb_read_status,
 		.suspend	= genphy_suspend,
@@ -2116,6 +2171,8 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features	= rtl822x_c45_get_features,
 		.config_aneg	= rtl822x_c45_config_aneg,
 		.config_init	= rtl822x_config_init,
+		.inband_caps	= rtl822x_inband_caps,
+		.config_inband	= rtl822x_config_inband,
 		.read_status	= rtl822xb_c45_read_status,
 		.suspend	= genphy_c45_pma_suspend,
 		.resume		= rtlgen_c45_resume,
@@ -2125,6 +2182,8 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
 		.config_init	= rtl822xb_config_init,
+		.inband_caps	= rtl822x_inband_caps,
+		.config_inband	= rtl822x_config_inband,
 		.get_rate_matching = rtl822xb_get_rate_matching,
 		.read_status	= rtl822xb_read_status,
 		.suspend	= genphy_suspend,
@@ -2138,6 +2197,8 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
 		.config_init	= rtl822xb_config_init,
+		.inband_caps	= rtl822x_inband_caps,
+		.config_inband	= rtl822x_config_inband,
 		.get_rate_matching = rtl822xb_get_rate_matching,
 		.read_status	= rtl822xb_read_status,
 		.suspend	= genphy_suspend,
@@ -2151,6 +2212,8 @@ static struct phy_driver realtek_drvs[] = {
 		.handle_interrupt = rtl8221b_handle_interrupt,
 		.probe		= rtl822x_probe,
 		.config_init	= rtl822xb_config_init,
+		.inband_caps	= rtl822x_inband_caps,
+		.config_inband	= rtl822x_config_inband,
 		.get_rate_matching = rtl822xb_get_rate_matching,
 		.get_features	= rtl822x_c45_get_features,
 		.config_aneg	= rtl822x_c45_config_aneg,
@@ -2164,6 +2227,8 @@ static struct phy_driver realtek_drvs[] = {
 		.get_features	= rtl822x_get_features,
 		.config_aneg	= rtl822x_config_aneg,
 		.config_init	= rtl822xb_config_init,
+		.inband_caps	= rtl822x_inband_caps,
+		.config_inband	= rtl822x_config_inband,
 		.get_rate_matching = rtl822xb_get_rate_matching,
 		.read_status	= rtl822xb_read_status,
 		.suspend	= genphy_suspend,
@@ -2177,6 +2242,8 @@ static struct phy_driver realtek_drvs[] = {
 		.handle_interrupt = rtl8221b_handle_interrupt,
 		.probe		= rtl822x_probe,
 		.config_init	= rtl822xb_config_init,
+		.inband_caps	= rtl822x_inband_caps,
+		.config_inband	= rtl822x_config_inband,
 		.get_rate_matching = rtl822xb_get_rate_matching,
 		.get_features	= rtl822x_c45_get_features,
 		.config_aneg	= rtl822x_c45_config_aneg,
Signature · 1 line
2.52.0
#4 lore raw

PATCH v2 3/5 net: phy: move mmd_phy_read and mmd_phy_write to phylib.h

In reply to Daniel Golle

Helper functions mmd_phy_read and mmd_phy_write are useful for PHYs which require custom MMD access functions for some but not all MMDs. Move mmd_phy_read and mmd_phy_write function prototypes from phylib-internal.h to phylib.h to make them available for PHY drivers.

---
v2: new patch

 drivers/net/phy/phylib-internal.h | 6 ------
 drivers/net/phy/phylib.h          | 5 +++++
 2 files changed, 5 insertions(+), 6 deletions(-)
drivers/net/phy/phylib-internal.h +0 -6
index ebda74eb60a54..dc9592c6bb8e7 100644
@@ -7,7 +7,6 @@
 #define __PHYLIB_INTERNAL_H
 
 struct phy_device;
-struct mii_bus;
 
 /*
  * phy_supported_speeds - return all speeds currently supported by a PHY device
@@ -21,11 +20,6 @@ void of_set_phy_timing_role(struct phy_device *phydev);
 int phy_speed_down_core(struct phy_device *phydev);
 void phy_check_downshift(struct phy_device *phydev);
 
-int mmd_phy_read(struct mii_bus *bus, int phy_addr, bool is_c45,
-		 int devad, u32 regnum);
-int mmd_phy_write(struct mii_bus *bus, int phy_addr, bool is_c45,
-		  int devad, u32 regnum, u16 val);
-
 int genphy_c45_read_eee_adv(struct phy_device *phydev, unsigned long *adv);
 
 #endif /* __PHYLIB_INTERNAL_H */
drivers/net/phy/phylib.h +5 -0
index c15484a805b39..0fba245f97458 100644
@@ -8,6 +8,7 @@
 
 struct device_node;
 struct phy_device;
+struct mii_bus;
 
 struct device_node *phy_package_get_node(struct phy_device *phydev);
 void *phy_package_get_priv(struct phy_device *phydev);
@@ -30,5 +31,9 @@ int devm_phy_package_join(struct device *dev, struct phy_device *phydev,
 			  int base_addr, size_t priv_size);
 int devm_of_phy_package_join(struct device *dev, struct phy_device *phydev,
 			     size_t priv_size);
+int mmd_phy_read(struct mii_bus *bus, int phy_addr, bool is_c45,
+		 int devad, u32 regnum);
+int mmd_phy_write(struct mii_bus *bus, int phy_addr, bool is_c45,
+		  int devad, u32 regnum, u16 val);
 
 #endif /* __PHYLIB_H */
Signature · 1 line
2.52.0
#6 lore raw

PATCH v2 4/5 net: phy: realtek: use paged access for MDIO_MMD_VEND2 in C22 mode

In reply to Daniel Golle

RTL822x cannot access MDIO_MMD_VEND2 via MII_MMD_CTRL/MII_MMD_DATA. A mapping to use paged access needs to be used instead. All other MMD devices can be accessed as usual.

Implement phy_read_mmd and phy_write_mmd using paged access for MDIO_MMD_VEND2 in Clause-22 mode instead of relying on MII_MMD_CTRL/MII_MMD_DATA. This allows eg. rtl822x_config_aneg to work as expected in case the MDIO bus doesn't support Clause-45 access.

---
v2:
- use mmd_phy_read and mmd_phy_write
- fix return value in on error (oldpage vs. ret)
- fix wrong parameter name (reg vs. mmdreg)

 drivers/net/phy/realtek/realtek_main.c | 91 +++++++++++++++++++++++++-
 1 file changed, 88 insertions(+), 3 deletions(-)
drivers/net/phy/realtek/realtek_main.c +88 -3
index 0653a9d8fcb6f..d1c7935a13acc 100644
@@ -18,6 +18,7 @@
 #include <linux/clk.h>
 #include <linux/string_choices.h>
 
+#include "../phylib.h"
 #include "realtek.h"
 
 #define RTL8201F_IER				0x13
@@ -140,9 +141,8 @@
 #define   RTL822X_VND1_SERDES_INBAND_ENABLE	0x70d0
 #define RTL822X_VND1_SERDES_DATA		0x7589
 
-/* RTL822X_VND2_XXXXX registers are only accessible when phydev->is_c45
- * is set, they cannot be accessed by C45-over-C22.
- */
+#define RTL822X_VND2_TO_PAGE(reg)		((reg) >> 4)
+#define RTL822X_VND2_TO_PAGE_REG(reg)		(16 + (((reg) & GENMASK(3, 0)) >> 1))
 #define RTL822X_VND2_C22_REG(reg)		(0xa400 + 2 * (reg))
 
 #define RTL8221B_VND2_INER			0xa4d2
@@ -1247,6 +1247,79 @@ static int rtl822x_probe(struct phy_device *phydev)
 	return 0;
 }
 
+/* RTL822x cannot access MDIO_MMD_VEND2 via MII_MMD_CTRL/MII_MMD_DATA.
+ * A mapping to use paged access needs to be used instead.
+ * All other MMD devices can be accessed as usual.
+ */
+static int rtl822xb_read_mmd(struct phy_device *phydev, int devnum, u16 reg)
+{
+	int oldpage, ret, read_ret;
+	u16 page;
+
+	/* Use default method for all MMDs except MDIO_MMD_VEND2 or in case
+	 * Clause-45 access is available
+	 */
+	if (devnum != MDIO_MMD_VEND2 || phydev->is_c45)
+		return mmd_phy_read(phydev->mdio.bus, phydev->mdio.addr,
+				    phydev->is_c45, devnum, reg);
+
+	/* Use paged access for MDIO_MMD_VEND2 over Clause-22 */
+	page = RTL822X_VND2_TO_PAGE(reg);
+	oldpage = __phy_read(phydev, RTL821x_PAGE_SELECT);
+	if (oldpage < 0)
+		return oldpage;
+
+	if (oldpage != page) {
+		ret = __phy_write(phydev, RTL821x_PAGE_SELECT, page);
+		if (ret < 0)
+			return ret;
+	}
+
+	read_ret = __phy_read(phydev, RTL822X_VND2_TO_PAGE_REG(reg));
+	if (oldpage != page) {
+		ret = __phy_write(phydev, RTL821x_PAGE_SELECT, oldpage);
+		if (ret < 0)
+			return ret;
+	}
+
+	return read_ret;
+}
+
+static int rtl822xb_write_mmd(struct phy_device *phydev, int devnum, u16 reg,
+			      u16 val)
+{
+	int oldpage, ret, write_ret;
+	u16 page;
+
+	/* Use default method for all MMDs except MDIO_MMD_VEND2 or in case
+	 * Clause-45 access is available
+	 */
+	if (devnum != MDIO_MMD_VEND2 || phydev->is_c45)
+		return mmd_phy_write(phydev->mdio.bus, phydev->mdio.addr,
+				     phydev->is_c45, devnum, reg, val);
+
+	/* Use paged access for MDIO_MMD_VEND2 over Clause-22 */
+	page = RTL822X_VND2_TO_PAGE(reg);
+	oldpage = __phy_read(phydev, RTL821x_PAGE_SELECT);
+	if (oldpage < 0)
+		return oldpage;
+
+	if (oldpage != page) {
+		ret = __phy_write(phydev, RTL821x_PAGE_SELECT, page);
+		if (ret < 0)
+			return ret;
+	}
+
+	write_ret = __phy_write(phydev,  RTL822X_VND2_TO_PAGE_REG(reg), val);
+	if (oldpage != page) {
+		ret = __phy_write(phydev, RTL821x_PAGE_SELECT, oldpage);
+		if (ret < 0)
+			return ret;
+	}
+
+	return write_ret;
+}
+
 static int rtl822x_set_serdes_option_mode(struct phy_device *phydev, bool gen1)
 {
 	bool has_2500, has_sgmii;
@@ -2150,6 +2223,8 @@ static struct phy_driver realtek_drvs[] = {
 		.resume		= rtlgen_resume,
 		.read_page	= rtl821x_read_page,
 		.write_page	= rtl821x_write_page,
+		.read_mmd	= rtl822xb_read_mmd,
+		.write_mmd	= rtl822xb_write_mmd,
 	}, {
 		.match_phy_device = rtl8221b_match_phy_device,
 		.name		= "RTL8226B_RTL8221B 2.5Gbps PHY",
@@ -2164,6 +2239,8 @@ static struct phy_driver realtek_drvs[] = {
 		.resume		= rtlgen_resume,
 		.read_page	= rtl821x_read_page,
 		.write_page	= rtl821x_write_page,
+		.read_mmd	= rtl822xb_read_mmd,
+		.write_mmd	= rtl822xb_write_mmd,
 	}, {
 		PHY_ID_MATCH_EXACT(0x001cc838),
 		.name		= "RTL8226-CG 2.5Gbps PHY",
@@ -2176,6 +2253,8 @@ static struct phy_driver realtek_drvs[] = {
 		.read_status	= rtl822xb_c45_read_status,
 		.suspend	= genphy_c45_pma_suspend,
 		.resume		= rtlgen_c45_resume,
+		.read_mmd	= rtl822xb_read_mmd,
+		.write_mmd	= rtl822xb_write_mmd,
 	}, {
 		PHY_ID_MATCH_EXACT(0x001cc848),
 		.name		= "RTL8226B-CG_RTL8221B-CG 2.5Gbps PHY",
@@ -2190,6 +2269,8 @@ static struct phy_driver realtek_drvs[] = {
 		.resume		= rtlgen_resume,
 		.read_page	= rtl821x_read_page,
 		.write_page	= rtl821x_write_page,
+		.read_mmd	= rtl822xb_read_mmd,
+		.write_mmd	= rtl822xb_write_mmd,
 	}, {
 		.match_phy_device = rtl8221b_vb_cg_c22_match_phy_device,
 		.name		= "RTL8221B-VB-CG 2.5Gbps PHY (C22)",
@@ -2205,6 +2286,8 @@ static struct phy_driver realtek_drvs[] = {
 		.resume		= rtlgen_resume,
 		.read_page	= rtl821x_read_page,
 		.write_page	= rtl821x_write_page,
+		.read_mmd	= rtl822xb_read_mmd,
+		.write_mmd	= rtl822xb_write_mmd,
 	}, {
 		.match_phy_device = rtl8221b_vb_cg_c45_match_phy_device,
 		.name		= "RTL8221B-VB-CG 2.5Gbps PHY (C45)",
@@ -2235,6 +2318,8 @@ static struct phy_driver realtek_drvs[] = {
 		.resume		= rtlgen_resume,
 		.read_page	= rtl821x_read_page,
 		.write_page	= rtl821x_write_page,
+		.read_mmd	= rtl822xb_read_mmd,
+		.write_mmd	= rtl822xb_write_mmd,
 	}, {
 		.match_phy_device = rtl8221b_vm_cg_c45_match_phy_device,
 		.name		= "RTL8221B-VM-CG 2.5Gbps PHY (C45)",
Signature · 1 line
2.52.0
#8 lore raw

PATCH v2 5/5 net: phy: realtek: get rid of magic number in rtlgen_read_status()

In reply to Daniel Golle

Use newly introduced helper macros RTL822X_VND2_TO_PAGE and RTL822X_VND2_TO_PAGE_REG to access RTL_VEND2_PHYSR register over Clause-22 paged access instead of using magic numbers.

---
v2: no changes

 drivers/net/phy/realtek/realtek_main.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/net/phy/realtek/realtek_main.c +2 -1
index d1c7935a13acc..eb5b540ada0e5 100644
@@ -1154,7 +1154,8 @@ static int rtlgen_read_status(struct phy_device *phydev)
 	if (!phydev->link)
 		return 0;
 
-	val = phy_read_paged(phydev, 0xa43, 0x12);
+	val = phy_read_paged(phydev, RTL822X_VND2_TO_PAGE(RTL_VND2_PHYSR),
+			     RTL822X_VND2_TO_PAGE_REG(RTL_VND2_PHYSR));
 	if (val < 0)
 		return val;
 
Signature · 1 line
2.52.0
Reviewed-by on v2 4/5
#7 lore raw

Re: [PATCH net-next v2 4/5] net: phy: realtek: use paged access for MDIO_MMD_VEND2 in C22 mode

In reply to Daniel Golle

Hi Daniel,

Quoted 11 lines · Daniel Golle

RTL822x cannot access MDIO_MMD_VEND2 via MII_MMD_CTRL/MII_MMD_DATA. A mapping to use paged access needs to be used instead. All other MMD devices can be accessed as usual.

Implement phy_read_mmd and phy_write_mmd using paged access for MDIO_MMD_VEND2 in Clause-22 mode instead of relying on MII_MMD_CTRL/MII_MMD_DATA. This allows eg. rtl822x_config_aneg to work as expected in case the MDIO bus doesn't support Clause-45 access.

This looks good to me

Maxime

Reviewed-by on v2 5/5
#9 lore raw

Re: [PATCH net-next v2 5/5] net: phy: realtek: get rid of magic number in rtlgen_read_status()

In reply to Daniel Golle
Quoted 5 lines · Daniel Golle

Use newly introduced helper macros RTL822X_VND2_TO_PAGE and RTL822X_VND2_TO_PAGE_REG to access RTL_VEND2_PHYSR register over Clause-22 paged access instead of using magic numbers.

That's nicer indeed !

Maxime

maintainer Reviewed-by on v2 3/5
#5 lore raw

Re: [PATCH net-next v2 3/5] net: phy: move mmd_phy_read and mmd_phy_write to phylib.h

In reply to Daniel Golle
Quoted 6 lines · Daniel Golle

Helper functions mmd_phy_read and mmd_phy_write are useful for PHYs which require custom MMD access functions for some but not all MMDs. Move mmd_phy_read and mmd_phy_write function prototypes from phylib-internal.h to phylib.h to make them available for PHY drivers.

Andrew

#10 lore raw
In reply to Daniel Golle
This series was applied to netdev/net-next.git (main) by Paolo Abeni <[email protected]>:

Hello:

This series was applied to netdev/net-next.git (main) by Paolo Abeni <[email protected]>:

Quoted 10 lines · On Mon, 5 Jan 2026 16:37:38 +0000 you wrote:

This series improves the RealTek PHY driver, mostly for 2.5GE PHYs. It implements configuring SGMII and 2500Base-X in-band auto-negotiation and improves using the PHYs in Clause-22-only mode.

Note that the rtl822x_serdes_write() function introduced by this series is going to be reused to configure polarities of SerDes RX and TX lanes once series "PHY polarity inversion via generic device tree properties" has been applied.

[...]

Here is the summary with links:
- [net-next,v2,1/5] net: phy: realtek: fix whitespace in struct phy_driver initializers

    https://git.kernel.org/netdev/net-next/c/50326b48f0cf
  - [net-next,v2,2/5] net: phy: realtek: implement configuring in-band an
    https://git.kernel.org/netdev/net-next/c/10fbd71fc5f9
  - [net-next,v2,3/5] net: phy: move mmd_phy_read and mmd_phy_write to phylib.h
    https://git.kernel.org/netdev/net-next/c/65de36f5eae1
  - [net-next,v2,4/5] net: phy: realtek: use paged access for MDIO_MMD_VEND2 in C22 mode
    https://git.kernel.org/netdev/net-next/c/1850ec20d6e7
  - [net-next,v2,5/5] net: phy: realtek: get rid of magic number in rtlgen_read_status()
    https://git.kernel.org/netdev/net-next/c/d8489935f597

You are awesome, thank you!

Signature · 2 lines
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html