net: dsa: mxl-gsw1xx: setup polarities and validate chip
Subsystems (5)
v2 cover net: dsa: mxl-gsw1xx: setup polarities and validate chip
Now that common PHY properties make it easy to configure the SerDes RX and TX polarities, use that for the SGMII/1000Base-X/2500Base-X PCS of the MaxLinear GSW1xx switches.
Also, validate hardware in probe() function to make sure the switch is actually present and MDIO communication works properly.
---
Changes since initial submission:
* use allOf to include phy-common-props in dt-schema
* use phy_get_manual_rx_polarity and phy_get_manual_tx_polarity helpers instead of open-coding them
Daniel Golle (4):
net: dsa: mxl-gsw1xx: setup polarities and validate chip
dt-bindings: net: dsa: lantiq,gswip: reference common PHY properties
net: dsa: mxl-gsw1xx: configure PCS polarities
net: dsa: mxl-gsw1xx: validate chip ID
.../bindings/net/dsa/lantiq,gswip.yaml | 4 ++ drivers/net/dsa/lantiq/Kconfig | 1 + drivers/net/dsa/lantiq/mxl-gsw1xx.c | 61 +++++++++++++++---- drivers/net/dsa/lantiq/mxl-gsw1xx.h | 9 +++ 4 files changed, 64 insertions(+), 11 deletions(-)
Signature · 1 line
2.52.0
A message that is not in the archive (sent off-list or not yet received): 875329426cffe416ebe6a3064ed632604f29f100.1769733972.git.daniel@makrotopia.org
PATCH v2 1/3 dt-bindings: net: dsa: lantiq,gswip: reference common PHY properties
Reference the common PHY properties so RX and TX SerDes lane polarity of the SGMII/1000Base-X/2500Base-X PCS can be configured.
---
v2: use allOf to include PHY common properties, add example use
Documentation/devicetree/bindings/net/dsa/lantiq,gswip.yaml | 4 ++++ 1 file changed, 4 insertions(+)
Documentation/devicetree/bindings/net/dsa/lantiq,gswip.yaml +4 -0
@@ -105,6 +105,8 @@ patternProperties: patternProperties: "^(ethernet-)?port@[0-6]$": $ref: dsa-port.yaml# + allOf: + - $ref: /schemas/phy/phy-common-props.yaml# unevaluatedProperties: false properties:
@@ -288,6 +290,7 @@ examples: - | #include <dt-bindings/leds/common.h> + #include <dt-bindings/phy/phy.h> mdio { #address-cells = <1>;
@@ -320,6 +323,7 @@ examples: label = "wan"; phy-mode = "1000base-x"; managed = "in-band-status"; + rx-polarity = <PHY_POL_INVERT>; }; port@5 {
Signature · 1 line
2.52.0
PATCH v2 2/3 net: dsa: mxl-gsw1xx: configure PCS polarities
In reply to a message not in the archiveConfigure SerDes PCS RX and TX polarities using the newly introduced generic properties.
---
v2: use phy_get_manual_rx_polarity and phy_get_manual_tx_polarity
drivers/net/dsa/lantiq/Kconfig | 1 + drivers/net/dsa/lantiq/mxl-gsw1xx.c | 34 ++++++++++++++++++++--------- 2 files changed, 25 insertions(+), 10 deletions(-)
drivers/net/dsa/lantiq/Kconfig +1 -0
@@ -15,6 +15,7 @@ config NET_DSA_MXL_GSW1XX tristate "MaxLinear GSW1xx Ethernet switch support" select NET_DSA_TAG_MXL_GSW1XX select NET_DSA_LANTIQ_COMMON + select PHY_COMMON_PROPS help This enables support for the Intel/MaxLinear GSW1xx family of 1GE switches.
drivers/net/dsa/lantiq/mxl-gsw1xx.c +24 -10
@@ -15,6 +15,8 @@#include <linux/module.h> #include <linux/of_device.h> #include <linux/of_mdio.h> +#include <linux/phy/phy-common-props.h> +#include <linux/property.h> #include <linux/regmap.h> #include <linux/workqueue.h> #include <net/dsa.h>
@@ -229,11 +231,17 @@ static int gsw1xx_pcs_phy_xaui_write(struct gsw1xx_priv *priv, u16 addr, 1000, 100000); } -static int gsw1xx_pcs_reset (struct gsw1xx_priv *priv) +static int gsw1xx_pcs_reset (struct gsw1xx_priv *priv,phy_interface_t interface) { +struct dsa_port *pcs_port; +unsigned int pol;int ret;u16 val; + pcs_port =dsa_to_port (priv->gswip.ds,GSW1XX_SGMII_PORT ); +if (!pcs_port) +return -EINVAL ; +/* Assert and deassert SGMII shell reset */ ret =regmap_set_bits (priv->shell,GSW1XX_SHELL_RST_REQ ,GSW1XX_RST_REQ_SGMII_SHELL );
@@ -260,15 +268,17 @@ static int gsw1xx_pcs_reset(struct gsw1xx_priv *priv)FIELD_PREP (GSW1XX_SGMII_PHY_RX0_CFG2_FILT_CNT ,GSW1XX_SGMII_PHY_RX0_CFG2_FILT_CNT_DEF ); + ret =phy_get_manual_rx_polarity (of_fwnode_handle (pcs_port->dn), +phy_modes (interface), &pol); +if (ret) +return ret; +/* RX lane seems to be inverted internally, so bit * GSW1XX_SGMII_PHY_RX0_CFG2_INVERT needs to be set for normal * (ie. non-inverted) operation. -* -* TODO: Take care of inverted RX pair once generic property is -* available */ - - val |=GSW1XX_SGMII_PHY_RX0_CFG2_INVERT ; +if (pol ==PHY_POL_NORMAL ) + val |=GSW1XX_SGMII_PHY_RX0_CFG2_INVERT ; ret =regmap_write (priv->sgmii,GSW1XX_SGMII_PHY_RX0_CFG2 , val);if (ret <0 )
@@ -277,9 +287,13 @@ static int gsw1xx_pcs_reset(struct gsw1xx_priv *priv) val =FIELD_PREP (GSW1XX_SGMII_PHY_TX0_CFG3_VBOOST_LEVEL ,GSW1XX_SGMII_PHY_TX0_CFG3_VBOOST_LEVEL_DEF ); -/* TODO: Take care of inverted TX pair once generic property is -* available -*/ + ret =phy_get_manual_tx_polarity (of_fwnode_handle (pcs_port->dn), +phy_modes (interface), &pol); +if (ret) +return ret; + +if (pol ==PHY_POL_INVERT ) + val |=GSW1XX_SGMII_PHY_TX0_CFG3_INVERT ; ret =regmap_write (priv->sgmii,GSW1XX_SGMII_PHY_TX0_CFG3 , val);if (ret <0 )
@@ -336,7 +350,7 @@ static int gsw1xx_pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode, priv->tbi_interface =PHY_INTERFACE_MODE_NA ;if (!reconf) - ret =gsw1xx_pcs_reset (priv); + ret =gsw1xx_pcs_reset (priv, interface);if (ret)return ret;
Signature · 1 line
2.52.0
Vladimir Oltean
maintainerRe: [PATCH net-next v2 2/3] net: dsa: mxl-gsw1xx: configure PCS polarities
Quoted 7 lines · Daniel Golle
Configure SerDes PCS RX and TX polarities using the newly introduced generic properties.
Signed-off-by Daniel Golle <[email protected]>---
drivers/net/dsa/lantiq/mxl-gsw1xx.c +0
-0@@ -260,15 +268,17 @@ static int gsw1xx_pcs_reset(struct gsw1xx_priv *priv) FIELD_PREP(GSW1XX_SGMII_PHY_RX0_CFG2_FILT_CNT,
drivers/net/dsa/lantiq/mxl-gsw1xx.c static int gsw1xx_pcs_reset(struct gsw1xx_priv *priv) · line 278
Quoted 10 lines
drivers/net/dsa/lantiq/mxl-gsw1xx.c +5
-0GSW1XX_SGMII_PHY_RX0_CFG2_FILT_CNT_DEF); + ret =phy_get_manual_rx_polarity (of_fwnode_handle (pcs_port->dn), +phy_modes (interface), &pol); +if (ret) +return ret; +/* RX lane seems to be inverted internally, so bit * GSW1XX_SGMII_PHY_RX0_CFG2_INVERT needs to be set for normal * (ie. non-inverted) operation.
Sorry, I just noticed this existing comment now.
I think this patch set has the right solution with the wrong explanation, and as someone who cares about logical consistency as much as about functionality, I think it's worth resending to clarify something.
There exists a problem which, at a high level, is that the signal can be inverted at multiple levels in its path. When multiple levels are configurable, it becomes important to know "which level does this DT property correspond to". Otherwise it's not clear how inversions at multiple layers relate to each other.
For someone who doesn't study the problem deeply, it will be confusing that this approach is inconsistent with what I intend to do for XPCS on SJA1105:
https://lore.kernel.org/netdev/[email protected]/
That is, if one needs to invert the TX lane signal in the PCS to achieve normal polarity at the pins (to compensate for internal inversion in the SerDes/PMA), then the PCS node needs to have "tx-polarity = <PHY_POL_INVERT>".
In Documentation/devicetree/bindings/phy/phy-common-props.yaml it explicitly says that "If the property is absent, the default value is undefined." in order to permit drivers to call phy_get_rx_polarity() with a custom default_val, rather than phy_get_manual_rx_polarity() which implies a predefined default_val of PHY_POL_NORMAL.
This is the opposite of what you're doing. You need to invert the RX signal in the SerDes for what can be assumed to be a hidden inversion in the PCS, but you make that invisible in the device tree, interpreting PHY_POL_NORMAL as "inverted" when programming the SerDes.
Only difference, which also makes your approach self-consistent, is that the rx-polarity property goes neither in the PCS nor the SerDes OF nodes (which don't exist), but in the port node. If we interpret the port node as what happens at the pins, the totality of the internal data path layers with no further insight into sub-components, then it's OK and is the simplest solution to the problem.
But it needs to be presented 100% clearly, with a very clear distinction between the PCS, the SerDes PHY and the port as a whole. Patches 1 and 2 use these 3 concepts very interchangeably, ranging from comments/commit messages ("Reference the common PHY properties so RX and TX SerDes lane polarity of the SGMII/1000Base-X/2500Base-X PCS can be configured") to code placement (SerDes configuration done in gsw1xx_pcs_reset()) to variable names ("pcs_port" could lose the "pcs" portion, to avoid somebody unfamiliar with the HW doing some refactoring where they take the port OF node as the PCS OF node, for other purposes as well, perhaps not applicable).
Quoted 39 lines
drivers/net/dsa/lantiq/mxl-gsw1xx.c +10
-9-* -* TODO: Take care of inverted RX pair once generic property is -* available */ - - val |=GSW1XX_SGMII_PHY_RX0_CFG2_INVERT ; +if (pol ==PHY_POL_NORMAL ) + val |=GSW1XX_SGMII_PHY_RX0_CFG2_INVERT ; ret =regmap_write (priv->sgmii,GSW1XX_SGMII_PHY_RX0_CFG2 , val);if (ret <0 )@@ -277,9 +287,13 @@ static int gsw1xx_pcs_reset(struct gsw1xx_priv *priv) val =FIELD_PREP (GSW1XX_SGMII_PHY_TX0_CFG3_VBOOST_LEVEL ,GSW1XX_SGMII_PHY_TX0_CFG3_VBOOST_LEVEL_DEF ); -/* TODO: Take care of inverted TX pair once generic property is -* available -*/ + ret =phy_get_manual_tx_polarity (of_fwnode_handle (pcs_port->dn), +phy_modes (interface), &pol); +if (ret) +return ret; + +if (pol ==PHY_POL_INVERT ) + val |=GSW1XX_SGMII_PHY_TX0_CFG3_INVERT ; ret =regmap_write (priv->sgmii,GSW1XX_SGMII_PHY_TX0_CFG3 , val);if (ret <0 )@@ -336,7 +350,7 @@ static int gsw1xx_pcs_config(struct phylink_pcs *pcs, unsigned int neg_mode, priv->tbi_interface =PHY_INTERFACE_MODE_NA ;if (!reconf) - ret =gsw1xx_pcs_reset (priv); + ret =gsw1xx_pcs_reset (priv, interface);if (ret)return ret;Signature · 1 line
2.52.0
PATCH v2 3/3 net: dsa: mxl-gsw1xx: validate chip ID
In reply to a message not in the archiveNo check for actually present hardware is being performed in the probe function of the mxl-gsw1xx switch driver. So even if the switch isn't present at the configured MDIO bus address the driver wrongly tells the user that a "GSWIP version 0 mod 0" was found, outputting errors about PHY capabilities not matching.
Read and validate the chip MANU_ID and PNUM_ID registers and output information while probing, but return an error and abort probing in case the hardware is not actually present.
---
v2: no changes
drivers/net/dsa/lantiq/mxl-gsw1xx.c | 27 ++++++++++++++++++++++++++- drivers/net/dsa/lantiq/mxl-gsw1xx.h | 9 +++++++++ 2 files changed, 35 insertions(+), 1 deletion(-)
drivers/net/dsa/lantiq/mxl-gsw1xx.c +26 -1
@@ -685,7 +685,9 @@ static int gsw1xx_probe(struct mdio_device *mdiodev) {struct device *dev = &mdiodev->dev;struct gsw1xx_priv *priv; -u32 version; +u32 version, val; +u8 shellver; +u16 pnum;int ret; priv =devm_kzalloc (dev,sizeof (*priv),GFP_KERNEL );
@@ -733,6 +735,27 @@ static int gsw1xx_probe(struct mdio_device *mdiodev)if (IS_ERR (priv->shell))return PTR_ERR (priv->shell); + ret =regmap_read (priv->shell,GSW1XX_SHELL_MANU_ID , &val); +if (ret <0 ) +return ret; + +/* validate chip ID */ +if (FIELD_GET (GSW1XX_SHELL_MANU_ID_FIX1 , val) !=1 ) +return -ENODEV ; + +if (FIELD_GET (GSW1XX_SHELL_MANU_ID_MANID , val) != +GSW1XX_SHELL_MANU_ID_MANID_VAL ) +return -ENODEV ; + + pnum =FIELD_GET (GSW1XX_SHELL_MANU_ID_PNUML , val); + + ret =regmap_read (priv->shell,GSW1XX_SHELL_PNUM_ID , &val); +if (ret <0 ) +return ret; + + pnum |=FIELD_GET (GSW1XX_SHELL_PNUM_ID_PNUMM , val) <<4 ; + shellver =FIELD_GET (GSW1XX_SHELL_PNUM_ID_VER , val); + ret =gsw1xx_serdes_pcs_init (priv);if (ret <0 )return ret;
@@ -753,6 +776,8 @@ static int gsw1xx_probe(struct mdio_device *mdiodev)if (ret)return ret; +dev_info (dev,"standalone switch part number 0x%x v1.%u\n" , pnum, shellver); +dev_set_drvdata (dev, &priv->gswip);return 0 ;
drivers/net/dsa/lantiq/mxl-gsw1xx.h +9 -0
@@ -110,6 +110,15 @@#define GSW1XX_SHELL_BASE 0xfa00#define GSW1XX_SHELL_RST_REQ 0x01#define GSW1XX_RST_REQ_SGMII_SHELL BIT(5) +#define GSW1XX_SHELL_MANU_ID 0x10 +#define GSW1XX_SHELL_MANU_ID_PNUML GENMASK(15, 12) +#define GSW1XX_SHELL_MANU_ID_MANID GENMASK(11, 1) +#define GSW1XX_SHELL_MANU_ID_MANID_VAL 0x389 +#define GSW1XX_SHELL_MANU_ID_FIX1 BIT(0) +#define GSW1XX_SHELL_PNUM_ID 0x11 +#define GSW1XX_SHELL_PNUM_ID_VER GENMASK(15, 12) +#define GSW1XX_SHELL_PNUM_ID_PNUMM GENMASK(11, 0) +/* RGMII PAD Slew Control Register */ #define GSW1XX_SHELL_RGMII_SLEW_CFG 0x78#define RGMII_SLEW_CFG_DRV_TXC BIT(2)
Signature · 1 line
2.52.0