Skip to contentSkip to conversation

ATA command timeouts, ata_piix 2.6.15.6

DISCUSSION Julian T. J. Midgley 1 participant 1 message Mar 13, 2006

lore
Share & tools
lore
#0 lore raw

I have a Dell Latitude D610 that is brought to its knees by ata timeouts intermittently (about once a day, on average). Rebooting has always recovered thus far.

Kernel 2.6.15.6 (with Suspend2 2.2 patch), using ata_piix - kernel .config at: http://b.xenoclast.org/config_ata_prob

At the point the machine becomes unusable, I get the following on the console:

ata1: command 0x35 timeout, stat 0xd0 host_stat 0x21
ata1: translated ATA stat/err 0xd0/00 to SCSI SK/ASC/ASCQ 0xb/47/00 Buffer I/O error on device sda3, logical block 1533312
ata1: command 0x35 timeout, stat 0xd0 host_stat 0x21
ata1: translated ATA stat/err 0xd0/00 to SCSI SK/ASC/ASCQ 0xb/47/00 Buffer I/O error on device sda3, logical block 1533546
ata1: command 0x25 timeout, stat 0xd0 host_stat 0x21
...

Any thoughts would be much appreciated. lspci/hdparm output below.

Julian

lspci
0000:00:1f.2 IDE interface: Intel Corp. 82801FBM (ICH6M) SATA Controller (rev 03 ) (prog-if 80 [Master])
Subsystem: Dell: Unknown device 0182
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 209 I/O ports at <ignored>
I/O ports at <ignored>
I/O ports at <ignored>
I/O ports at <ignored>
I/O ports at bfa0 [size=16]
Capabilities: [70] Power Management version 2

hdparm -I /dev/sda
/dev/sda:

ATA device, with non-removable media

	Model Number:       ST960822A                               
	Serial Number:      3LF3FBFK
	Firmware Revision:  8.03    
Standards:
	Used: ATA/ATAPI-6 T13 1410D revision 2 
	Supported: 6 5 4 3 
Configuration:
	Logical		max	current
	cylinders	16383	16383
	heads		16	16
	sectors/track	63	63
	--
	CHS current addressable sectors:   16514064
	LBA    user addressable sectors:  117210240
	LBA48  user addressable sectors:  117210240
	device size with M = 1024*1024:       57231 MBytes
	device size with M = 1000*1000:       60011 MBytes (60 GB)

Capabilities:
LBA, IORDY(can be disabled)
bytes avail on r/w long: 4 Queue depth: 1
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 8
Advanced power management level: unknown setting (0x8080) Recommended acoustic management value: 254, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=240ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* READ BUFFER cmd
* WRITE BUFFER cmd
* Host Protected Area feature set
* Look-ahead
* Write cache
* Power Management feature set
Security Mode feature set
* SMART feature set
* FLUSH CACHE EXT command
* Mandatory FLUSH CACHE command
* Device Configuration Overlay feature set
* 48-bit Address feature set
Automatic Acoustic Management feature set
SET MAX security extension
* Advanced Power Management feature set
* DOWNLOAD MICROCODE cmd
* SMART self-test
* SMART error logging
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- above Vih
Device num = 0 determined by CSEL
Checksum: correct

Signature · 3 lines
Julian T. J. Midgley                       http://www.xenoclast.org/
Cambridge, England.
PGP: BCC7863F FP: 52D9 1750 5721 7E58 C9E1  A7D5 3027 2F2E BCC7 863F