Skip to contentSkip to conversation

Write YAFFS filesystem images to NAND

PATCH New Frank Mandarino 2 participants 3 messages Sep 7, 2006

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Write YAFFS filesystem images to NAND

Hi,

The attached patch for common/cmd_nand.c provides the ability to write YAFFS filesystem images to NAND flash memory, using the newer MTD-based nand code.

The patch extends the nand write command to parse a ".yaffs1" suffix for yaffs1 filesystems, or a ".yaffs" or ".yaffs2" suffix for yaffs2 filesystems.

Yaffs1 filesystems support 512-byte page, 16-byte oob NAND chips, while yaffs2 filesystems support 2048-byte page, 64-byte oob NAND chips.

Yaffs1 filesystem images can be generated using the mkyaffsimage utility in the yaffs2/utils directory.

Yaffs2 filesystem images can be generated using the mkyaffs2image utility in the yaffs2/utils directory, after applying Sergey Kubushyn's patch. See
http://aleph1.co.uk/lurker/message/20060211.004601.77b55bf3.en.html.

So, for example, to write a yaffs1 filesystem image of length 0x526320 from address 0x20000000 in ram to offset 0x100000 in flash, run the command:

nand write.yaffs1 20000000 100000 526320

The area to be written must be erased before writing the filesystem.

I have tested this code with yaffs1 filesystems, and, in fact, I am finally able to run Linux with rootfstype=yaffs. I am unable to test with yaffs2 filesystems because I don't have access to a system using 2048+64 NAND chips.

Regards,
../fam

Signature · 11 lines
Frank Mandarino                                fmandarino(a)endrelia.com
Endrelia Technologies Inc.
Toronto, Ontario, Canada

-------------- next part --------------
A non-text attachment was scrubbed...
Name: nand_write_yaffs.patch
Type: text/x-patch
Size: 5209 bytes
Desc: not available
Url : http://lists.denx.de/pipermail/u-boot/attachments/20060907/d4405bb3/attachment.bin 
#1 lore raw

PATCH 1/1 Write YAFFS filesystem images to NAND

Hi Frank,

You can run yaffs2 in yaffs1 compatibility mode. Check the yaffs2 source for the correct configuration options.

-blair

Quoted 35 lines · Frank Mandarino

Hi,

The attached patch for common/cmd_nand.c provides the ability to write YAFFS filesystem images to NAND flash memory, using the newer MTD-based nand code.

The patch extends the nand write command to parse a ".yaffs1" suffix for yaffs1 filesystems, or a ".yaffs" or ".yaffs2" suffix for yaffs2 filesystems.

Yaffs1 filesystems support 512-byte page, 16-byte oob NAND chips, while yaffs2 filesystems support 2048-byte page, 64-byte oob NAND chips.

Yaffs1 filesystem images can be generated using the mkyaffsimage utility in the yaffs2/utils directory.

Yaffs2 filesystem images can be generated using the mkyaffs2image utility in the yaffs2/utils directory, after applying Sergey Kubushyn's patch. See
http://aleph1.co.uk/lurker/message/20060211.004601.77b55bf3.en.html.

So, for example, to write a yaffs1 filesystem image of length 0x526320 from address 0x20000000 in ram to offset 0x100000 in flash, run the command:

   nand write.yaffs1 20000000 100000 526320

The area to be written must be erased before writing the filesystem.

I have tested this code with yaffs1 filesystems, and, in fact, I am finally able to run Linux with rootfstype=yaffs. I am unable to test with yaffs2 filesystems because I don't have access to a system using 2048+64 NAND chips.

Regards,
../fam

#2 lore raw

PATCH 1/1 Write YAFFS filesystem images to NAND

Hi Blair,

Thanks for the response, but I'm not sure what you are getting at.

I am aware of the yaffs1 compatibility mode, and I think I am running the yaffs2 code in that mode. At least I only installed the yaffs2 code into my Linux kernel.

But this has nothing to do with U-Boot's ability to write a yaffs filesystem image to NAND flash.

In yaffs1 compatibility mode, I believe the yaffs2 code assumes that the OOB is formatted as it is in a yaffs1 filesystem, so I am providing a way to write the older yaffs1 OOB format, or the newer yaffs2 OOB format.

Regards,
../fam

Quoted 50 lines · Blair Barnett

Hi Frank,

You can run yaffs2 in yaffs1 compatibility mode. Check the yaffs2 source for the correct configuration options.

-blair

Quoted 28 lines · Frank Mandarino

Hi,

The attached patch for common/cmd_nand.c provides the ability to write YAFFS filesystem images to NAND flash memory, using the newer MTD-based nand code.

The patch extends the nand write command to parse a ".yaffs1" suffix for yaffs1 filesystems, or a ".yaffs" or ".yaffs2" suffix for yaffs2 filesystems.

Yaffs1 filesystems support 512-byte page, 16-byte oob NAND chips, while yaffs2 filesystems support 2048-byte page, 64-byte oob NAND chips.

Yaffs1 filesystem images can be generated using the mkyaffsimage utility in the yaffs2/utils directory.

Yaffs2 filesystem images can be generated using the mkyaffs2image utility in the yaffs2/utils directory, after applying Sergey Kubushyn's patch. See
http://aleph1.co.uk/lurker/message/20060211.004601.77b55bf3.en.html.

So, for example, to write a yaffs1 filesystem image of length 0x526320 from address 0x20000000 in ram to offset 0x100000 in flash, run the command:

   nand write.yaffs1 20000000 100000 526320

The area to be written must be erased before writing the filesystem.

Quoted 7 lines

I have tested this code with yaffs1 filesystems, and, in fact, I am finally able to run Linux with rootfstype=yaffs. I am unable to test with yaffs2 filesystems because I don't have access to a system using 2048+64 NAND chips.

Regards,
../fam

-------------------------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security? Get stuff done quickly with pre-integrated technology to make your job easier Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642

Signature · 3 lines
Frank Mandarino                                fmandarino(a)endrelia.com
Endrelia Technologies Inc.
Toronto, Ontario, Canada