Skip to contentSkip to conversation

big delay on boot with new pata drivers

DISCUSSION Alessandro Bono 2 participants 2 messages Sep 24, 2006 – Sep 28, 2006 libata

lore
Share & tools
lore
#0 lore raw

Hi

I'm trying new libata pata support from linux-2.6.18-git3 system seems working but on startup there is a big delay while probing for ata devices

these are relevant log from kernel

libata version 2.00 loaded.
ata_piix 0000:00:1f.1: version 2.00ac6
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xFFA8 irq 15 scsi0 : ata_piix
ata1.00: ATA-6, max UDMA/100, 195371568 sectors: LBA
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/100
scsi1 : ata_piix
ata2.00: ATAPI, max UDMA/33
ata2.01: qc timeout (cmd 0xa1)
ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
ata2: failed to recover some devices, retrying in 5 secs ata2.01: qc timeout (cmd 0xa1)
ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
ata2: failed to recover some devices, retrying in 5 secs ata2.01: qc timeout (cmd 0xa1)
ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
ata2: failed to recover some devices, retrying in 5 secs ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct access ATA FUJITSU MHV2100A 0000 PQ: 0 ANSI: 5
SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
scsi 1:0:0:0: CD/DVD MATSHITA UJ-820D 1.01 PQ: 0 ANSI: 5
......
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5

same machine with 2.6.18 and old ide modules

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 7 (level, low) -> IRQ 7
ICH4: chipset revision 3
ICH4: not 100%% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0...
hda: FUJITSU MHV2100AH, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: MATSHITAUJ-820D, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63
hda: cache flushes supported
hda: hda1 hda2
......
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20

from lspci
0000:00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Sony Corporation: Unknown device 8188
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at ffa0 [size=16]
Region 5: Memory at 88000000 (32-bit, non-prefetchable) [size=1K]

#1 lore raw
Quoted 19 lines · Alessandro Bono

Hi

I'm trying new libata pata support from linux-2.6.18-git3 system seems working but on startup there is a big delay while probing for ata devices

these are relevant log from kernel

libata version 2.00 loaded.
ata_piix 0000:00:1f.1: version 2.00ac6
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ata1: PATA max UDMA/100 cmd 0x1F0 ctl 0x3F6 bmdma 0xFFA0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xFFA8 irq 15 scsi0 : ata_piix

Quoted 8 lines

ata1.00: ATA-6, max UDMA/100, 195371568 sectors: LBA ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/100
scsi1 : ata_piix
ata2.00: ATAPI, max UDMA/33
ata2.01: qc timeout (cmd 0xa1)
ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
ata2: failed to recover some devices, retrying in 5 secs

This looks like the PATA version of the phantom device problem:
The MATSHITA UJ-820D drive acts for device 1 and creates an inexistent ata2.01 illusion here.

Quoted 42 lines

ata2.01: qc timeout (cmd 0xa1)
ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
ata2: failed to recover some devices, retrying in 5 secs ata2.01: qc timeout (cmd 0xa1)
ata2.01: failed to IDENTIFY (I/O error, err_mask=0x4)
ata2: failed to recover some devices, retrying in 5 secs ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct access ATA FUJITSU MHV2100A 0000 PQ: 0 ANSI: 5
SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 195371568 512-byte hdwr sectors (100030 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
scsi 1:0:0:0: CD/DVD MATSHITA UJ-820D 1.01 PQ: 0 ANSI: 5
......
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5

same machine with 2.6.18 and old ide modules

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 7 (level, low) -> IRQ 7
ICH4: chipset revision 3
ICH4: not 100%% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0...
hda: FUJITSU MHV2100AH, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: MATSHITAUJ-820D, ATAPI CD/DVD-ROM drive

Quoted 10 lines

ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63
hda: cache flushes supported
hda: hda1 hda2
......
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20

The old IDE uses polling PIO to IDENTIFY, so it knows something wrong quickly. Libata uses irq PIO to IDENTIFY and has to wait for 30 seconds timeout to figure out what it sees is illusion actually.

Unlike the "bang at the door" method of old IDE, libata has tests to filter out the faulty devices (ex. ata_devchk(), ata_dev_classify()). However the ghost device can pass the tests here and causes the long delay.

--
albert