: Exaudio produces noise on all speakers for 5.1 channels
A NOTE has been added to this issue.
======================================================================
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=1210>
======================================================================
Reported By: andersin Assigned To: Clemens Ladisch ====================================================================== Project: ALSA - driver Issue ID: 1210 Category: USB - usb-audio Reproducibility: always Severity: minor Priority: normal Status: assigned Distribution: Kernel Version: ====================================================================== Date Submitted: 06-23-2005 23:54 CEST Last Modified: 08-24-2005 00:50 CEST
======================================================================
Summary: Exaudio produces noise on all speakers for 5.1
channels
Description:
I am using a soundblaster extigy with ALSA ver. 1.0.9b and am happy to say
that stereo sound works find and that all 6 speakers can produce some sound.
With more than 2 channel output, I experience problems. speaker-test, which
works for 1 and 2 channels, results in a hissing/crackling for 3,5,6 channels, which changes in pitch depending on the number of channels. For 4
channels, it loops, producing the following output
speaker-test 0.0.8
Playback device is extigy
Stream parameters are 48000Hz, S16_LE, 4 channels Using 16 octaves of pink noise
Rate set to 48000Hz (requested 48000Hz)
Buffer size range from 96 to 8192
Period size range from 48 to 4096
Periods = 4
Buffer time size 2525
To choose buffer_size = 8192
To choose period_size = 2048
was set period_size = 2048
was set buffer_size = 8192
Unable to set hw params for playback: Invalid argument Setting of hwparams failed: Invalid argument Rate set to 48000Hz (requested 48000Hz)
[ The "Rate set to ..." part is repeated continuously ]
Setting my capture device to mixer, I was able to record the output with arecord -c 6 -f dat -r 48000 /root/speaker-test-6ch.wav . The distortion is
still present when playing the file, forcing 2 channels in aplay.
In addition to using speaker test, I tried using the route plugin to isolate
the rear channels. When I route to any channel, I can hear the same output on
all 5 (not sure about Woofer) channels, no matter which channel I route to.
Here is the relevant setup:
pcm.route1 {
type route;
slave.pcm "extigy";
slave.channels 6;
ttable.0.0 1.0;}
The music that I played had similar distortions like the one for speaker test
and played considerably slower than when player with 2 channels. Again I could record and replay the effect. The setup was slightly different in order
to route the stereo channels to all 6 speakers.
For routing with 4 slave channels, I get a failure (as expected), this time
with the output:
Playing WAVE 'test.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Stereo
aplay: set_params:910: Unable to install hw params: ACCESS: RW_INTERLEAVED FORMAT: S16_LE SUBFORMAT: STD SAMPLE_BITS: 16 FRAME_BITS: 32 CHANNELS: 2 RATE: 48000 PERIOD_TIME: (42666 42667) PERIOD_SIZE: 2048 PERIOD_BYTES: 8192 PERIODS: 4 BUFFER_TIME: (170666 170667) BUFFER_SIZE: 8192 BUFFER_BYTES: 32768 TICK_TIME: 1000
This is all the relevant bits that I can think of at the moment. Thank you for
reading this far. If anybody thinks it is important to get the recorded files, I am happy to sent them. I am grateful for any nudge on what I am doing wrong with my setup.
Christoph Burger-Scheidlin
======================================================================
----------------------------------------------------------------------
andersin - 06-24-05 17:47
----------------------------------------------------------------------
I added two files, each representing one complete iteration of the speaker-test program. I hope the files are small enough.
----------------------------------------------------------------------
andersin - 08-24-05 00:50
----------------------------------------------------------------------
Hmm, nothing happened in a while. Reading over the comments, I think I gave you the wrong files. I downloaded some ac3 test files and decoded them using ac3dec -6 -D extigy. The file I uploaded is a recording of the two front speakers.
Issue History
Date Modified Username Field Change
======================================================================
06-23-05 23:54 andersin New Issue
06-24-05 09:21 Clemens LadischFile Added: alsa-lib-start-threshold-check.diff
06-24-05 09:22 Clemens LadischFile Deleted: alsa-lib-start-threshold-check.diff
06-24-05 09:23 Clemens LadischNote Added: 0005205
06-24-05 10:14 andersin File Added: stream0.txt
06-24-05 10:16 andersin Note Added: 0005208
06-24-05 10:25 Clemens LadischNote Added: 0005209
06-24-05 13:38 andersin Note Added: 0005218
06-24-05 15:23 andersin Note Edited: 0005218
06-24-05 17:22 Clemens LadischNote Added: 0005239
06-24-05 17:44 andersin File Added: speaker-test-6ch.mp3
06-24-05 17:44 andersin File Added: speaker-test-2ch.mp3
06-24-05 17:47 andersin Note Added: 0005242
08-24-05 00:50 andersin Note Added: 0005920
======================================================================
-------------------------------------------------------
SF.Net email is Sponsored by the Better Software Conference & EXPO September 19-22, 2005 * San Francisco, CA * Development Lifecycle Practices Agile & Plan-Driven Development * Managing Projects & Teams * Testing & QA Security * Process Improvement & Measurement * http://www.sqe.com/bsce5sf