mmc: meson: add MMC driver for Meson GX (S905)
Subsystems (3)
A message that is not in the archive (sent off-list or not yet received): [email protected]
PATCH v3 2/3 mmc: meson: add MMC driver for Meson GX (S905)
This driver implements MMC support on Meson GX (S905) based systems. It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoring
---
v2:
- addressed review comments
- general refactoring
v3:
- remove config symbol MMC_MESON_GX_SD_PORT
--- arch/arm/include/asm/arch-meson/sd_emmc.h | 89 +++++++++ drivers/mmc/Kconfig | 6 + drivers/mmc/Makefile | 1 + drivers/mmc/meson_gx_mmc.c | 291 ++++++++++++++++++++++++++++++ include/configs/meson-gxbb-common.h | 4 + 5 files changed, 391 insertions(+) create mode 100644 arch/arm/include/asm/arch-meson/sd_emmc.h create mode 100644 drivers/mmc/meson_gx_mmc.c
arch/arm/include/asm/arch-meson/sd_emmc.h new file +89 -0
@@ -0,0 +1,89 @@ +/* +* (C) Copyright 2017 Carlo Caione <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __SD_EMMC_H__ +#define __SD_EMMC_H__ + +#include <mmc.h> + +#define SDIO_PORT_A 0 +#define SDIO_PORT_B 1 +#define SDIO_PORT_C 2 + +#define SD_EMMC_CLKSRC_24M 24000000/* 24 MHz */ +#define SD_EMMC_CLKSRC_DIV2 1000000000/* 1 GHz */ + +#define MESON_SD_EMMC_CLOCK 0x00 +#define CLK_MAX_DIV 63 +#define CLK_SRC_24M (0 << 6) +#define CLK_SRC_DIV2 (1 << 6) +#define CLK_CO_PHASE_000 (0 << 8) +#define CLK_CO_PHASE_090 (1 << 8) +#define CLK_CO_PHASE_180 (2 << 8) +#define CLK_CO_PHASE_270 (3 << 8) +#define CLK_TX_PHASE_000 (0 << 10) +#define CLK_TX_PHASE_090 (1 << 10) +#define CLK_TX_PHASE_180 (2 << 10) +#define CLK_TX_PHASE_270 (3 << 10) +#define CLK_ALWAYS_ON BIT(24) + +#define MESON_SD_EMMC_CFG 0x44 +#define CFG_BUS_WIDTH_MASK GENMASK(1, 0) +#define CFG_BUS_WIDTH_1 0 +#define CFG_BUS_WIDTH_4 1 +#define CFG_BUS_WIDTH_8 2 +#define CFG_BL_LEN_MASK GENMASK(7, 4) +#define CFG_BL_LEN_SHIFT 4 +#define CFG_BL_LEN_512 (9 << 4) +#define CFG_RESP_TIMEOUT_MASK GENMASK(11, 8) +#define CFG_RESP_TIMEOUT_256 (8 << 8) +#define CFG_RC_CC_MASK GENMASK(15, 12) +#define CFG_RC_CC_16 (4 << 12) +#define CFG_SDCLK_ALWAYS_ON BIT(18) +#define CFG_AUTO_CLK BIT(23) + +#define MESON_SD_EMMC_STATUS 0x48 +#define STATUS_MASK GENMASK(15, 0) +#define STATUS_ERR_MASK GENMASK(12, 0) +#define STATUS_RXD_ERR_MASK GENMASK(7, 0) +#define STATUS_TXD_ERR BIT(8) +#define STATUS_DESC_ERR BIT(9) +#define STATUS_RESP_ERR BIT(10) +#define STATUS_RESP_TIMEOUT BIT(11) +#define STATUS_DESC_TIMEOUT BIT(12) +#define STATUS_END_OF_CHAIN BIT(13) + +#define MESON_SD_EMMC_IRQ_EN 0x4c + +#define MESON_SD_EMMC_CMD_CFG 0x50 +#define CMD_CFG_LENGTH_MASK GENMASK(8, 0) +#define CMD_CFG_BLOCK_MODE BIT(9) +#define CMD_CFG_R1B BIT(10) +#define CMD_CFG_END_OF_CHAIN BIT(11) +#define CMD_CFG_TIMEOUT_4S (12 << 12) +#define CMD_CFG_NO_RESP BIT(16) +#define CMD_CFG_DATA_IO BIT(18) +#define CMD_CFG_DATA_WR BIT(19) +#define CMD_CFG_RESP_NOCRC BIT(20) +#define CMD_CFG_RESP_128 BIT(21) +#define CMD_CFG_CMD_INDEX_SHIFT 24 +#define CMD_CFG_OWNER BIT(31) + +#define MESON_SD_EMMC_CMD_ARG 0x54 +#define MESON_SD_EMMC_CMD_DAT 0x58 +#define MESON_SD_EMMC_CMD_RSP 0x5c +#define MESON_SD_EMMC_CMD_RSP1 0x60 +#define MESON_SD_EMMC_CMD_RSP2 0x64 +#define MESON_SD_EMMC_CMD_RSP3 0x68 + +struct meson_mmc_platdata { +struct mmc_config cfg; +struct mmc mmc; +void *regbase; +void *w_buf; +}; + +#endif
drivers/mmc/Kconfig +6 -0
@@ -168,6 +168,12 @@ config ZYNQ_SDHCI help Support for Arasan SDHCI host controller on Zynq/ZynqMP ARM SoCs platform +config MMC_MESON_GX + bool "Meson GX EMMC controller support" + depends on DM_MMC && BLK && DM_MMC_OPS && ARCH_MESON + help + Support for EMMC host controller on Meson GX ARM SoCs platform (S905) + config ROCKCHIP_SDHCI bool "Arasan SDHCI controller for Rockchip support" depends on DM_MMC && BLK && DM_MMC_OPS
drivers/mmc/Makefile +1 -0
@@ -31,6 +31,7 @@ ifdef CONFIG_SUPPORT_EMMC_BOOT obj-$(CONFIG_GENERIC_MMC) += mmc_boot.o endif obj-$(CONFIG_GENERIC_ATMEL_MCI) += gen_atmel_mci.o +obj-$(CONFIG_MMC_MESON_GX) += meson_gx_mmc.o obj-$(CONFIG_MMC_SPI) += mmc_spi.o obj-$(CONFIG_MVEBU_MMC) += mvebu_mmc.o obj-$(CONFIG_MMC_OMAP_HS) += omap_hsmmc.o
drivers/mmc/meson_gx_mmc.c new file +291 -0
291 lines not on this page · raw message
include/configs/meson-gxbb-common.h +4 -0
@@ -23,6 +23,10 @@#define CONFIG_SYS_INIT_SP_ADDR 0x20000000#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_TEXT_BASE +#ifdef CONFIG_MMC +#define CONFIG_GENERIC_MMC +#endif +/* Generic Interrupt Controller Definitions */ #define GICD_BASE 0xc4301000#define GICC_BASE 0xc4302000
Signature · 1 line
2.11.0
PATCH v3 2/3 mmc: meson: add MMC driver for Meson GX (S905)
Quoted 8 lines · Heiner Kallweit
This driver implements MMC support on Meson GX (S905) based systems. It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoringSigned-off-by Carlo Caione <[email protected]>Signed-off-by Andreas F?rber <[email protected]>Signed-off-by Heiner Kallweit <[email protected]>
Andreas's comment is what this patch's author is Carlo..Not just add Signed-off tag for Carlo.
When you send the email, needs to add "From: Carlo Caione <[email protected]>", not yours.
Quoted 2 lines
---
v2:
V3 should be here..not V2.
Quoted 20 lines
- addressed review comments
- general refactoring
v3:
- remove config symbolMMC_MESON_GX_SD_PORT--- arch/arm/include/asm/arch-meson/sd_emmc.h | 89 +++++++++ drivers/mmc/Kconfig | 6 + drivers/mmc/Makefile | 1 + drivers/mmc/meson_gx_mmc.c | 291 ++++++++++++++++++++++++++++++ include/configs/meson-gxbb-common.h | 4 + 5 files changed, 391 insertions(+) create mode 100644 arch/arm/include/asm/arch-meson/sd_emmc.h create mode 100644 drivers/mmc/meson_gx_mmc.carch/arm/include/asm/arch-meson/sd_emmc.h new file +0
-0
arch/arm/include/asm/arch-meson/sd_emmc.h line 2
Quoted 2 lines
arch/arm/include/asm/arch-meson/sd_emmc.h new file +2
-0@@ -0,0 +1,89 @@ +/* +* (C) Copyright 2017 Carlo Caione <[email protected]>
I don't know Carlo already shared at github..So 2016 might be right, not 2017.
Quoted 429 lines
arch/arm/include/asm/arch-meson/sd_emmc.h new file +87
-0+* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __SD_EMMC_H__ +#define __SD_EMMC_H__ + +#include <mmc.h> + +#define SDIO_PORT_A 0 +#define SDIO_PORT_B 1 +#define SDIO_PORT_C 2 + +#define SD_EMMC_CLKSRC_24M 24000000/* 24 MHz */ +#define SD_EMMC_CLKSRC_DIV2 1000000000/* 1 GHz */ + +#define MESON_SD_EMMC_CLOCK 0x00 +#define CLK_MAX_DIV 63 +#define CLK_SRC_24M (0 << 6) +#define CLK_SRC_DIV2 (1 << 6) +#define CLK_CO_PHASE_000 (0 << 8) +#define CLK_CO_PHASE_090 (1 << 8) +#define CLK_CO_PHASE_180 (2 << 8) +#define CLK_CO_PHASE_270 (3 << 8) +#define CLK_TX_PHASE_000 (0 << 10) +#define CLK_TX_PHASE_090 (1 << 10) +#define CLK_TX_PHASE_180 (2 << 10) +#define CLK_TX_PHASE_270 (3 << 10) +#define CLK_ALWAYS_ON BIT(24) + +#define MESON_SD_EMMC_CFG 0x44 +#define CFG_BUS_WIDTH_MASK GENMASK(1, 0) +#define CFG_BUS_WIDTH_1 0 +#define CFG_BUS_WIDTH_4 1 +#define CFG_BUS_WIDTH_8 2 +#define CFG_BL_LEN_MASK GENMASK(7, 4) +#define CFG_BL_LEN_SHIFT 4 +#define CFG_BL_LEN_512 (9 << 4) +#define CFG_RESP_TIMEOUT_MASK GENMASK(11, 8) +#define CFG_RESP_TIMEOUT_256 (8 << 8) +#define CFG_RC_CC_MASK GENMASK(15, 12) +#define CFG_RC_CC_16 (4 << 12) +#define CFG_SDCLK_ALWAYS_ON BIT(18) +#define CFG_AUTO_CLK BIT(23) + +#define MESON_SD_EMMC_STATUS 0x48 +#define STATUS_MASK GENMASK(15, 0) +#define STATUS_ERR_MASK GENMASK(12, 0) +#define STATUS_RXD_ERR_MASK GENMASK(7, 0) +#define STATUS_TXD_ERR BIT(8) +#define STATUS_DESC_ERR BIT(9) +#define STATUS_RESP_ERR BIT(10) +#define STATUS_RESP_TIMEOUT BIT(11) +#define STATUS_DESC_TIMEOUT BIT(12) +#define STATUS_END_OF_CHAIN BIT(13) + +#define MESON_SD_EMMC_IRQ_EN 0x4c + +#define MESON_SD_EMMC_CMD_CFG 0x50 +#define CMD_CFG_LENGTH_MASK GENMASK(8, 0) +#define CMD_CFG_BLOCK_MODE BIT(9) +#define CMD_CFG_R1B BIT(10) +#define CMD_CFG_END_OF_CHAIN BIT(11) +#define CMD_CFG_TIMEOUT_4S (12 << 12) +#define CMD_CFG_NO_RESP BIT(16) +#define CMD_CFG_DATA_IO BIT(18) +#define CMD_CFG_DATA_WR BIT(19) +#define CMD_CFG_RESP_NOCRC BIT(20) +#define CMD_CFG_RESP_128 BIT(21) +#define CMD_CFG_CMD_INDEX_SHIFT 24 +#define CMD_CFG_OWNER BIT(31) + +#define MESON_SD_EMMC_CMD_ARG 0x54 +#define MESON_SD_EMMC_CMD_DAT 0x58 +#define MESON_SD_EMMC_CMD_RSP 0x5c +#define MESON_SD_EMMC_CMD_RSP1 0x60 +#define MESON_SD_EMMC_CMD_RSP2 0x64 +#define MESON_SD_EMMC_CMD_RSP3 0x68 + +struct meson_mmc_platdata { +struct mmc_config cfg; +struct mmc mmc; +void *regbase; +void *w_buf; +}; + +#endif drivers/mmc/Kconfig +6
-0@@ -168,6 +168,12 @@ config ZYNQ_SDHCI help Support for Arasan SDHCI host controller on Zynq/ZynqMP ARM SoCs platform +config MMC_MESON_GX + bool "Meson GX EMMC controller support" + depends on DM_MMC && BLK && DM_MMC_OPS && ARCH_MESON + help + Support for EMMC host controller on Meson GX ARM SoCs platform (S905) + config ROCKCHIP_SDHCI bool "Arasan SDHCI controller for Rockchip support" depends on DM_MMC && BLK && DM_MMC_OPSdrivers/mmc/Makefile +1
-0@@ -31,6 +31,7 @@ ifdef CONFIG_SUPPORT_EMMC_BOOT obj-$(CONFIG_GENERIC_MMC) += mmc_boot.o endif obj-$(CONFIG_GENERIC_ATMEL_MCI) += gen_atmel_mci.o +obj-$(CONFIG_MMC_MESON_GX) += meson_gx_mmc.o obj-$(CONFIG_MMC_SPI) += mmc_spi.o obj-$(CONFIG_MVEBU_MMC) += mvebu_mmc.o obj-$(CONFIG_MMC_OMAP_HS) += omap_hsmmc.odrivers/mmc/meson_gx_mmc.c new file +291
-0@@ -0,0 +1,291 @@ +/* +* (C) Copyright 2017 Carlo Caione <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#include <common.h> +#include <fdtdec.h> +#include <malloc.h> +#include <mmc.h> +#include <asm/io.h> +#include <asm/arch/sd_emmc.h> +#include <dm/device.h> +#include <linux/log2.h> + +static inline void *get_regbase (const struct mmc *mmc) +{ +struct meson_mmc_platdata *pdata = mmc->priv; + +return pdata->regbase; +} + +static inline uint32_t meson_read (struct mmc *mmc,int offset) +{ +return readl (get_regbase (mmc) + offset); +} + +static inline void meson_write (struct mmc *mmc,uint32_t val,int offset) +{ +writel (val,get_regbase (mmc) + offset); +} + +static void meson_mmc_config_clock (struct mmc *mmc) +{ +uint32_t meson_mmc_clk =0 ; +unsigned int clk, clk_src, clk_div; + +/* 1GHz / CLK_MAX_DIV = 15,9 MHz */ +if (mmc->clock >16000000 ) { + clk =SD_EMMC_CLKSRC_DIV2 ; + clk_src =CLK_SRC_DIV2 ; + }else { + clk =SD_EMMC_CLKSRC_24M ; + clk_src =CLK_SRC_24M ; + } + clk_div =DIV_ROUND_UP (clk, mmc->clock); + +/* 180 phase core clock */ + meson_mmc_clk |=CLK_CO_PHASE_180 ; + +/* 180 phase tx clock */ + meson_mmc_clk |=CLK_TX_PHASE_180 ; + +/* clock settings */ + meson_mmc_clk |= clk_src; + meson_mmc_clk |= clk_div; + +meson_write (mmc, meson_mmc_clk,MESON_SD_EMMC_CLOCK ); +} + +static int meson_dm_mmc_set_ios (struct udevice *dev) +{ +struct mmc *mmc =mmc_get_mmc_dev (dev); +uint32_t meson_mmc_cfg; + +meson_mmc_config_clock (mmc); + + meson_mmc_cfg =meson_read (mmc,MESON_SD_EMMC_CFG ); + + meson_mmc_cfg &= ~CFG_BUS_WIDTH_MASK ; +if (mmc->bus_width ==1 ) + meson_mmc_cfg |=CFG_BUS_WIDTH_1 ; +else if (mmc->bus_width ==4 ) + meson_mmc_cfg |=CFG_BUS_WIDTH_4 ; +else if (mmc->bus_width ==8 ) + meson_mmc_cfg |=CFG_BUS_WIDTH_8 ; +else +return -EINVAL ; + +/* 512 bytes block length */ + meson_mmc_cfg &= ~CFG_BL_LEN_MASK ; + meson_mmc_cfg |=CFG_BL_LEN_512 ; + +/* Response timeout 256 clk */ + meson_mmc_cfg &= ~CFG_RESP_TIMEOUT_MASK ; + meson_mmc_cfg |=CFG_RESP_TIMEOUT_256 ; + +/* Command-command gap 16 clk */ + meson_mmc_cfg &= ~CFG_RC_CC_MASK ; + meson_mmc_cfg |=CFG_RC_CC_16 ; + +meson_write (mmc, meson_mmc_cfg,MESON_SD_EMMC_CFG ); + +return 0 ; +} + +static void meson_mmc_setup_cmd (struct mmc *mmc,struct mmc_data *data, +struct mmc_cmd *cmd) +{ +uint32_t meson_mmc_cmd =0 , cfg; + + meson_mmc_cmd |= cmd->cmdidx <<CMD_CFG_CMD_INDEX_SHIFT ; + +if (cmd->resp_type &MMC_RSP_PRESENT ) { +if (cmd->resp_type &MMC_RSP_136 ) + meson_mmc_cmd |=CMD_CFG_RESP_128 ; + +if (cmd->resp_type &MMC_RSP_BUSY ) + meson_mmc_cmd |=CMD_CFG_R1B ; + +if (!(cmd->resp_type &MMC_RSP_CRC )) + meson_mmc_cmd |=CMD_CFG_RESP_NOCRC ; + }else { + meson_mmc_cmd |=CMD_CFG_NO_RESP ; + } + +if (data) { + cfg =meson_read (mmc,MESON_SD_EMMC_CFG ); + cfg &= ~CFG_BL_LEN_MASK ; + cfg |=ilog2 (data->blocksize) <<CFG_BL_LEN_SHIFT ; +meson_write (mmc, cfg,MESON_SD_EMMC_CFG ); + +if (data->flags ==MMC_DATA_WRITE ) + meson_mmc_cmd |=CMD_CFG_DATA_WR ; + + cfg =CMD_CFG_DATA_IO |CMD_CFG_BLOCK_MODE | data->blocks; + meson_mmc_cmd |= cfg; + } + + cfg =CMD_CFG_TIMEOUT_4S |CMD_CFG_OWNER |CMD_CFG_END_OF_CHAIN ; + meson_mmc_cmd |= cfg; + +meson_write (mmc, meson_mmc_cmd,MESON_SD_EMMC_CMD_CFG ); +} + +static void meson_mmc_setup_addr (struct mmc *mmc,struct mmc_data *data) +{ +struct meson_mmc_platdata *pdata = mmc->priv; +unsigned int data_size; +uint32_t data_addr =0 ; + +if (data) { + data_size = data->blocks * data->blocksize; + +if (data->flags ==MMC_DATA_READ ) { + data_addr = (ulong ) data->dest; +invalidate_dcache_range (data_addr, + data_addr + data_size); + }else if (data->flags ==MMC_DATA_WRITE ) { + pdata->w_buf =calloc (data_size,sizeof (char )); + data_addr = (ulong ) pdata->w_buf; +memcpy (pdata->w_buf, data->src, data_size); +flush_dcache_range (data_addr, data_addr + data_size); + } + } + +meson_write (mmc, data_addr,MESON_SD_EMMC_CMD_DAT ); +} + +static void meson_mmc_read_response (struct mmc *mmc,struct mmc_cmd *cmd) +{ +if (cmd->resp_type &MMC_RSP_136 ) { + cmd->response[0 ] =meson_read (mmc,MESON_SD_EMMC_CMD_RSP3 ); + cmd->response[1 ] =meson_read (mmc,MESON_SD_EMMC_CMD_RSP2 ); + cmd->response[2 ] =meson_read (mmc,MESON_SD_EMMC_CMD_RSP1 ); + cmd->response[3 ] =meson_read (mmc,MESON_SD_EMMC_CMD_RSP ); + }else { + cmd->response[0 ] =meson_read (mmc,MESON_SD_EMMC_CMD_RSP ); + } +} + +static int meson_dm_mmc_send_cmd (struct udevice *dev,struct mmc_cmd *cmd, +struct mmc_data *data) +{ +struct mmc *mmc =mmc_get_mmc_dev (dev); +struct meson_mmc_platdata *pdata = mmc->priv; +uint32_t status; +ulong start; +int ret =0 ; + +/* max block size supported by chip is 512 byte */ +if (data && data->blocksize >512 ) +return -EINVAL ; + +meson_mmc_setup_cmd (mmc, data, cmd); +meson_mmc_setup_addr (mmc, data); + +meson_write (mmc, cmd->cmdarg,MESON_SD_EMMC_CMD_ARG ); + +/* use 10s timeout */ + start =get_timer (0 ); +do { + status =meson_read (mmc,MESON_SD_EMMC_STATUS ); + }while (!(status &STATUS_END_OF_CHAIN ) &&get_timer (start) <10000 ); + +if (!(status &STATUS_END_OF_CHAIN )) + ret = -ETIMEDOUT ; +else if (status &STATUS_RESP_TIMEOUT ) + ret = -ETIMEDOUT ; +else if (status &STATUS_ERR_MASK ) + ret = -EIO ; + +meson_mmc_read_response (mmc, cmd); + +if (data && data->flags ==MMC_DATA_WRITE ) +free (pdata->w_buf); + +/* reset status bits */ +meson_write (mmc,STATUS_MASK ,MESON_SD_EMMC_STATUS ); + +return ret; +} + +static const struct dm_mmc_ops meson_dm_mmc_ops = { + .send_cmd = meson_dm_mmc_send_cmd, + .set_ios = meson_dm_mmc_set_ios, +}; + +static int meson_mmc_ofdata_to_platdata (struct udevice *dev) +{ +struct meson_mmc_platdata *pdata =dev_get_platdata (dev); +fdt_addr_t addr; + + addr =dev_get_addr (dev); +if (addr ==FDT_ADDR_T_NONE ) +return -EINVAL ; + + pdata->regbase = (void *)addr; + +return 0 ; +} + +static int meson_mmc_probe (struct udevice *dev) +{ +struct meson_mmc_platdata *pdata =dev_get_platdata (dev); +struct mmc_uclass_priv *upriv =dev_get_uclass_priv (dev); +struct mmc *mmc = &pdata->mmc; +struct mmc_config *cfg = &pdata->cfg; +uint32_t val; + + cfg->voltages =MMC_VDD_33_34 |MMC_VDD_32_33 | +MMC_VDD_31_32 |MMC_VDD_165_195 ; + cfg->host_caps =MMC_MODE_8BIT |MMC_MODE_4BIT | + MMC_MODE_HS_52MHz |MMC_MODE_HS ; + cfg->f_min =DIV_ROUND_UP (SD_EMMC_CLKSRC_24M ,CLK_MAX_DIV ); + cfg->f_max =100000000 ;/* 100 MHz */ + cfg->b_max =256 ;/* max 256 blocks */ + cfg->name = dev->name; + + mmc->priv = pdata; + upriv->mmc = mmc; + +mmc_set_clock (mmc, cfg->f_min); + +/* reset all status bits */ +meson_write (mmc,STATUS_MASK ,MESON_SD_EMMC_STATUS ); + +/* disable interrupts */ +meson_write (mmc,0 ,MESON_SD_EMMC_IRQ_EN ); + +/* enable auto clock mode */ + val =meson_read (mmc,MESON_SD_EMMC_CFG ); + val &= ~CFG_SDCLK_ALWAYS_ON ; + val |=CFG_AUTO_CLK ; +meson_write (mmc, val,MESON_SD_EMMC_CFG ); + +return 0 ; +} + +int meson_mmc_bind (struct udevice *dev) +{ +struct meson_mmc_platdata *pdata =dev_get_platdata (dev); + +return mmc_bind (dev, &pdata->mmc, &pdata->cfg); +} + +static const struct udevice_id meson_mmc_match[] = { + { .compatible ="amlogic,meson-gx-mmc" }, + {/* sentinel */ } +}; + +U_BOOT_DRIVER (meson_mmc) = { + .name ="meson_gx_mmc" , + .id =UCLASS_MMC , + .of_match = meson_mmc_match, + .ops = &meson_dm_mmc_ops, + .probe = meson_mmc_probe, + .bind = meson_mmc_bind, + .ofdata_to_platdata = meson_mmc_ofdata_to_platdata, + .platdata_auto_alloc_size =sizeof (struct meson_mmc_platdata ), +};include/configs/meson-gxbb-common.h +4
-0@@ -23,6 +23,10 @@#define CONFIG_SYS_INIT_SP_ADDR 0x20000000#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_TEXT_BASE +#ifdef CONFIG_MMC +#define CONFIG_GENERIC_MMC +#endif +/* Generic Interrupt Controller Definitions */ #define GICD_BASE 0xc4301000#define GICC_BASE 0xc4302000
PATCH v3 2/3 mmc: meson: add MMC driver for Meson GX (S905)
Am 31.01.2017 um 14:24 schrieb Jaehoon Chung:
Quoted 6 lines · Heiner Kallweit
Quoted 5 lines
This driver implements MMC support on Meson GX (S905) based systems. It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoring
Quoted 8 lines
Quoted 3 lines
Signed-off-by Carlo Caione <[email protected]>Signed-off-by Andreas F?rber <[email protected]>Signed-off-by Heiner Kallweit <[email protected]>Andreas's comment is what this patch's author is Carlo..Not just add Signed-off tag for Carlo.
When you send the email, needs to add "From: Carlo Caione <[email protected]>", not yours.
I sent a v4 series addressing the review comments.
I tried sending patch 2 with Carlo as "From:", however the mail provider replaced this with my default mail address.
I checked with my other mail providers, they also allow only sender addresses belonging to me.
Quoted 462 lines
Quoted 3 lines
---
v2:V3 should be here..not V2.
Quoted 20 lines
- addressed review comments
- general refactoring
v3:
- remove config symbolMMC_MESON_GX_SD_PORT--- arch/arm/include/asm/arch-meson/sd_emmc.h | 89 +++++++++ drivers/mmc/Kconfig | 6 + drivers/mmc/Makefile | 1 + drivers/mmc/meson_gx_mmc.c | 291 ++++++++++++++++++++++++++++++ include/configs/meson-gxbb-common.h | 4 + 5 files changed, 391 insertions(+) create mode 100644 arch/arm/include/asm/arch-meson/sd_emmc.h create mode 100644 drivers/mmc/meson_gx_mmc.carch/arm/include/asm/arch-meson/sd_emmc.h new file +0
-0arch/arm/include/asm/arch-meson/sd_emmc.h line 2
Quoted 2 lines
arch/arm/include/asm/arch-meson/sd_emmc.h new file +2
-0@@ -0,0 +1,89 @@ +/* +* (C) Copyright 2017 Carlo Caione <[email protected]> I don't know Carlo already shared at github..So 2016 might be right, not 2017.
Quoted 429 lines
arch/arm/include/asm/arch-meson/sd_emmc.h new file +87
-0+* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#ifndef __SD_EMMC_H__ +#define __SD_EMMC_H__ + +#include <mmc.h> + +#define SDIO_PORT_A 0 +#define SDIO_PORT_B 1 +#define SDIO_PORT_C 2 + +#define SD_EMMC_CLKSRC_24M 24000000/* 24 MHz */ +#define SD_EMMC_CLKSRC_DIV2 1000000000/* 1 GHz */ + +#define MESON_SD_EMMC_CLOCK 0x00 +#define CLK_MAX_DIV 63 +#define CLK_SRC_24M (0 << 6) +#define CLK_SRC_DIV2 (1 << 6) +#define CLK_CO_PHASE_000 (0 << 8) +#define CLK_CO_PHASE_090 (1 << 8) +#define CLK_CO_PHASE_180 (2 << 8) +#define CLK_CO_PHASE_270 (3 << 8) +#define CLK_TX_PHASE_000 (0 << 10) +#define CLK_TX_PHASE_090 (1 << 10) +#define CLK_TX_PHASE_180 (2 << 10) +#define CLK_TX_PHASE_270 (3 << 10) +#define CLK_ALWAYS_ON BIT(24) + +#define MESON_SD_EMMC_CFG 0x44 +#define CFG_BUS_WIDTH_MASK GENMASK(1, 0) +#define CFG_BUS_WIDTH_1 0 +#define CFG_BUS_WIDTH_4 1 +#define CFG_BUS_WIDTH_8 2 +#define CFG_BL_LEN_MASK GENMASK(7, 4) +#define CFG_BL_LEN_SHIFT 4 +#define CFG_BL_LEN_512 (9 << 4) +#define CFG_RESP_TIMEOUT_MASK GENMASK(11, 8) +#define CFG_RESP_TIMEOUT_256 (8 << 8) +#define CFG_RC_CC_MASK GENMASK(15, 12) +#define CFG_RC_CC_16 (4 << 12) +#define CFG_SDCLK_ALWAYS_ON BIT(18) +#define CFG_AUTO_CLK BIT(23) + +#define MESON_SD_EMMC_STATUS 0x48 +#define STATUS_MASK GENMASK(15, 0) +#define STATUS_ERR_MASK GENMASK(12, 0) +#define STATUS_RXD_ERR_MASK GENMASK(7, 0) +#define STATUS_TXD_ERR BIT(8) +#define STATUS_DESC_ERR BIT(9) +#define STATUS_RESP_ERR BIT(10) +#define STATUS_RESP_TIMEOUT BIT(11) +#define STATUS_DESC_TIMEOUT BIT(12) +#define STATUS_END_OF_CHAIN BIT(13) + +#define MESON_SD_EMMC_IRQ_EN 0x4c + +#define MESON_SD_EMMC_CMD_CFG 0x50 +#define CMD_CFG_LENGTH_MASK GENMASK(8, 0) +#define CMD_CFG_BLOCK_MODE BIT(9) +#define CMD_CFG_R1B BIT(10) +#define CMD_CFG_END_OF_CHAIN BIT(11) +#define CMD_CFG_TIMEOUT_4S (12 << 12) +#define CMD_CFG_NO_RESP BIT(16) +#define CMD_CFG_DATA_IO BIT(18) +#define CMD_CFG_DATA_WR BIT(19) +#define CMD_CFG_RESP_NOCRC BIT(20) +#define CMD_CFG_RESP_128 BIT(21) +#define CMD_CFG_CMD_INDEX_SHIFT 24 +#define CMD_CFG_OWNER BIT(31) + +#define MESON_SD_EMMC_CMD_ARG 0x54 +#define MESON_SD_EMMC_CMD_DAT 0x58 +#define MESON_SD_EMMC_CMD_RSP 0x5c +#define MESON_SD_EMMC_CMD_RSP1 0x60 +#define MESON_SD_EMMC_CMD_RSP2 0x64 +#define MESON_SD_EMMC_CMD_RSP3 0x68 + +struct meson_mmc_platdata { +struct mmc_config cfg; +struct mmc mmc; +void *regbase; +void *w_buf; +}; + +#endif drivers/mmc/Kconfig +6
-0@@ -168,6 +168,12 @@ config ZYNQ_SDHCI help Support for Arasan SDHCI host controller on Zynq/ZynqMP ARM SoCs platform +config MMC_MESON_GX + bool "Meson GX EMMC controller support" + depends on DM_MMC && BLK && DM_MMC_OPS && ARCH_MESON + help + Support for EMMC host controller on Meson GX ARM SoCs platform (S905) + config ROCKCHIP_SDHCI bool "Arasan SDHCI controller for Rockchip support" depends on DM_MMC && BLK && DM_MMC_OPSdrivers/mmc/Makefile +1
-0@@ -31,6 +31,7 @@ ifdef CONFIG_SUPPORT_EMMC_BOOT obj-$(CONFIG_GENERIC_MMC) += mmc_boot.o endif obj-$(CONFIG_GENERIC_ATMEL_MCI) += gen_atmel_mci.o +obj-$(CONFIG_MMC_MESON_GX) += meson_gx_mmc.o obj-$(CONFIG_MMC_SPI) += mmc_spi.o obj-$(CONFIG_MVEBU_MMC) += mvebu_mmc.o obj-$(CONFIG_MMC_OMAP_HS) += omap_hsmmc.odrivers/mmc/meson_gx_mmc.c new file +291
-0@@ -0,0 +1,291 @@ +/* +* (C) Copyright 2017 Carlo Caione <[email protected]> +* +* SPDX-License-Identifier: GPL-2.0+ +*/ + +#include <common.h> +#include <fdtdec.h> +#include <malloc.h> +#include <mmc.h> +#include <asm/io.h> +#include <asm/arch/sd_emmc.h> +#include <dm/device.h> +#include <linux/log2.h> + +static inline void *get_regbase (const struct mmc *mmc) +{ +struct meson_mmc_platdata *pdata = mmc->priv; + +return pdata->regbase; +} + +static inline uint32_t meson_read (struct mmc *mmc,int offset) +{ +return readl (get_regbase (mmc) + offset); +} + +static inline void meson_write (struct mmc *mmc,uint32_t val,int offset) +{ +writel (val,get_regbase (mmc) + offset); +} + +static void meson_mmc_config_clock (struct mmc *mmc) +{ +uint32_t meson_mmc_clk =0 ; +unsigned int clk, clk_src, clk_div; + +/* 1GHz / CLK_MAX_DIV = 15,9 MHz */ +if (mmc->clock >16000000 ) { + clk =SD_EMMC_CLKSRC_DIV2 ; + clk_src =CLK_SRC_DIV2 ; + }else { + clk =SD_EMMC_CLKSRC_24M ; + clk_src =CLK_SRC_24M ; + } + clk_div =DIV_ROUND_UP (clk, mmc->clock); + +/* 180 phase core clock */ + meson_mmc_clk |=CLK_CO_PHASE_180 ; + +/* 180 phase tx clock */ + meson_mmc_clk |=CLK_TX_PHASE_180 ; + +/* clock settings */ + meson_mmc_clk |= clk_src; + meson_mmc_clk |= clk_div; + +meson_write (mmc, meson_mmc_clk,MESON_SD_EMMC_CLOCK ); +} + +static int meson_dm_mmc_set_ios (struct udevice *dev) +{ +struct mmc *mmc =mmc_get_mmc_dev (dev); +uint32_t meson_mmc_cfg; + +meson_mmc_config_clock (mmc); + + meson_mmc_cfg =meson_read (mmc,MESON_SD_EMMC_CFG ); + + meson_mmc_cfg &= ~CFG_BUS_WIDTH_MASK ; +if (mmc->bus_width ==1 ) + meson_mmc_cfg |=CFG_BUS_WIDTH_1 ; +else if (mmc->bus_width ==4 ) + meson_mmc_cfg |=CFG_BUS_WIDTH_4 ; +else if (mmc->bus_width ==8 ) + meson_mmc_cfg |=CFG_BUS_WIDTH_8 ; +else +return -EINVAL ; + +/* 512 bytes block length */ + meson_mmc_cfg &= ~CFG_BL_LEN_MASK ; + meson_mmc_cfg |=CFG_BL_LEN_512 ; + +/* Response timeout 256 clk */ + meson_mmc_cfg &= ~CFG_RESP_TIMEOUT_MASK ; + meson_mmc_cfg |=CFG_RESP_TIMEOUT_256 ; + +/* Command-command gap 16 clk */ + meson_mmc_cfg &= ~CFG_RC_CC_MASK ; + meson_mmc_cfg |=CFG_RC_CC_16 ; + +meson_write (mmc, meson_mmc_cfg,MESON_SD_EMMC_CFG ); + +return 0 ; +} + +static void meson_mmc_setup_cmd (struct mmc *mmc,struct mmc_data *data, +struct mmc_cmd *cmd) +{ +uint32_t meson_mmc_cmd =0 , cfg; + + meson_mmc_cmd |= cmd->cmdidx <<CMD_CFG_CMD_INDEX_SHIFT ; + +if (cmd->resp_type &MMC_RSP_PRESENT ) { +if (cmd->resp_type &MMC_RSP_136 ) + meson_mmc_cmd |=CMD_CFG_RESP_128 ; + +if (cmd->resp_type &MMC_RSP_BUSY ) + meson_mmc_cmd |=CMD_CFG_R1B ; + +if (!(cmd->resp_type &MMC_RSP_CRC )) + meson_mmc_cmd |=CMD_CFG_RESP_NOCRC ; + }else { + meson_mmc_cmd |=CMD_CFG_NO_RESP ; + } + +if (data) { + cfg =meson_read (mmc,MESON_SD_EMMC_CFG ); + cfg &= ~CFG_BL_LEN_MASK ; + cfg |=ilog2 (data->blocksize) <<CFG_BL_LEN_SHIFT ; +meson_write (mmc, cfg,MESON_SD_EMMC_CFG ); + +if (data->flags ==MMC_DATA_WRITE ) + meson_mmc_cmd |=CMD_CFG_DATA_WR ; + + cfg =CMD_CFG_DATA_IO |CMD_CFG_BLOCK_MODE | data->blocks; + meson_mmc_cmd |= cfg; + } + + cfg =CMD_CFG_TIMEOUT_4S |CMD_CFG_OWNER |CMD_CFG_END_OF_CHAIN ; + meson_mmc_cmd |= cfg; + +meson_write (mmc, meson_mmc_cmd,MESON_SD_EMMC_CMD_CFG ); +} + +static void meson_mmc_setup_addr (struct mmc *mmc,struct mmc_data *data) +{ +struct meson_mmc_platdata *pdata = mmc->priv; +unsigned int data_size; +uint32_t data_addr =0 ; + +if (data) { + data_size = data->blocks * data->blocksize; + +if (data->flags ==MMC_DATA_READ ) { + data_addr = (ulong ) data->dest; +invalidate_dcache_range (data_addr, + data_addr + data_size); + }else if (data->flags ==MMC_DATA_WRITE ) { + pdata->w_buf =calloc (data_size,sizeof (char )); + data_addr = (ulong ) pdata->w_buf; +memcpy (pdata->w_buf, data->src, data_size); +flush_dcache_range (data_addr, data_addr + data_size); + } + } + +meson_write (mmc, data_addr,MESON_SD_EMMC_CMD_DAT ); +} + +static void meson_mmc_read_response (struct mmc *mmc,struct mmc_cmd *cmd) +{ +if (cmd->resp_type &MMC_RSP_136 ) { + cmd->response[0 ] =meson_read (mmc,MESON_SD_EMMC_CMD_RSP3 ); + cmd->response[1 ] =meson_read (mmc,MESON_SD_EMMC_CMD_RSP2 ); + cmd->response[2 ] =meson_read (mmc,MESON_SD_EMMC_CMD_RSP1 ); + cmd->response[3 ] =meson_read (mmc,MESON_SD_EMMC_CMD_RSP ); + }else { + cmd->response[0 ] =meson_read (mmc,MESON_SD_EMMC_CMD_RSP ); + } +} + +static int meson_dm_mmc_send_cmd (struct udevice *dev,struct mmc_cmd *cmd, +struct mmc_data *data) +{ +struct mmc *mmc =mmc_get_mmc_dev (dev); +struct meson_mmc_platdata *pdata = mmc->priv; +uint32_t status; +ulong start; +int ret =0 ; + +/* max block size supported by chip is 512 byte */ +if (data && data->blocksize >512 ) +return -EINVAL ; + +meson_mmc_setup_cmd (mmc, data, cmd); +meson_mmc_setup_addr (mmc, data); + +meson_write (mmc, cmd->cmdarg,MESON_SD_EMMC_CMD_ARG ); + +/* use 10s timeout */ + start =get_timer (0 ); +do { + status =meson_read (mmc,MESON_SD_EMMC_STATUS ); + }while (!(status &STATUS_END_OF_CHAIN ) &&get_timer (start) <10000 ); + +if (!(status &STATUS_END_OF_CHAIN )) + ret = -ETIMEDOUT ; +else if (status &STATUS_RESP_TIMEOUT ) + ret = -ETIMEDOUT ; +else if (status &STATUS_ERR_MASK ) + ret = -EIO ; + +meson_mmc_read_response (mmc, cmd); + +if (data && data->flags ==MMC_DATA_WRITE ) +free (pdata->w_buf); + +/* reset status bits */ +meson_write (mmc,STATUS_MASK ,MESON_SD_EMMC_STATUS ); + +return ret; +} + +static const struct dm_mmc_ops meson_dm_mmc_ops = { + .send_cmd = meson_dm_mmc_send_cmd, + .set_ios = meson_dm_mmc_set_ios, +}; + +static int meson_mmc_ofdata_to_platdata (struct udevice *dev) +{ +struct meson_mmc_platdata *pdata =dev_get_platdata (dev); +fdt_addr_t addr; + + addr =dev_get_addr (dev); +if (addr ==FDT_ADDR_T_NONE ) +return -EINVAL ; + + pdata->regbase = (void *)addr; + +return 0 ; +} + +static int meson_mmc_probe (struct udevice *dev) +{ +struct meson_mmc_platdata *pdata =dev_get_platdata (dev); +struct mmc_uclass_priv *upriv =dev_get_uclass_priv (dev); +struct mmc *mmc = &pdata->mmc; +struct mmc_config *cfg = &pdata->cfg; +uint32_t val; + + cfg->voltages =MMC_VDD_33_34 |MMC_VDD_32_33 | +MMC_VDD_31_32 |MMC_VDD_165_195 ; + cfg->host_caps =MMC_MODE_8BIT |MMC_MODE_4BIT | + MMC_MODE_HS_52MHz |MMC_MODE_HS ; + cfg->f_min =DIV_ROUND_UP (SD_EMMC_CLKSRC_24M ,CLK_MAX_DIV ); + cfg->f_max =100000000 ;/* 100 MHz */ + cfg->b_max =256 ;/* max 256 blocks */ + cfg->name = dev->name; + + mmc->priv = pdata; + upriv->mmc = mmc; + +mmc_set_clock (mmc, cfg->f_min); + +/* reset all status bits */ +meson_write (mmc,STATUS_MASK ,MESON_SD_EMMC_STATUS ); + +/* disable interrupts */ +meson_write (mmc,0 ,MESON_SD_EMMC_IRQ_EN ); + +/* enable auto clock mode */ + val =meson_read (mmc,MESON_SD_EMMC_CFG ); + val &= ~CFG_SDCLK_ALWAYS_ON ; + val |=CFG_AUTO_CLK ; +meson_write (mmc, val,MESON_SD_EMMC_CFG ); + +return 0 ; +} + +int meson_mmc_bind (struct udevice *dev) +{ +struct meson_mmc_platdata *pdata =dev_get_platdata (dev); + +return mmc_bind (dev, &pdata->mmc, &pdata->cfg); +} + +static const struct udevice_id meson_mmc_match[] = { + { .compatible ="amlogic,meson-gx-mmc" }, + {/* sentinel */ } +}; + +U_BOOT_DRIVER (meson_mmc) = { + .name ="meson_gx_mmc" , + .id =UCLASS_MMC , + .of_match = meson_mmc_match, + .ops = &meson_dm_mmc_ops, + .probe = meson_mmc_probe, + .bind = meson_mmc_bind, + .ofdata_to_platdata = meson_mmc_ofdata_to_platdata, + .platdata_auto_alloc_size =sizeof (struct meson_mmc_platdata ), +};include/configs/meson-gxbb-common.h +4
-0@@ -23,6 +23,10 @@#define CONFIG_SYS_INIT_SP_ADDR 0x20000000#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_TEXT_BASE +#ifdef CONFIG_MMC +#define CONFIG_GENERIC_MMC +#endif +/* Generic Interrupt Controller Definitions */ #define GICD_BASE 0xc4301000#define GICC_BASE 0xc4302000
A message that is not in the archive (sent off-list or not yet received): [email protected]
PATCH v3 2/3 mmc: meson: add MMC driver for Meson GX (S905)
Am 02.02.2017 um 20:33 schrieb Karsten Merker:
Quoted 24 lines · Heiner Kallweit
Quoted 14 lines
Am 31.01.2017 um 14:24 schrieb Jaehoon Chung:
Quoted 13 lines · Heiner Kallweit
Quoted 8 lines
This driver implements MMC support on Meson GX (S905) based systems. It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoringSigned-off-by Carlo Caione <[email protected]>Signed-off-by Andreas F?rber <[email protected]>Signed-off-by Heiner Kallweit <[email protected]>Andreas's comment is what this patch's author is Carlo..Not just add Signed-off tag for Carlo.
Quoted 8 lines
Quoted 3 lines
When you send the email, needs to add "From: Carlo Caione <[email protected]>", not yours.
I sent a v4 series addressing the review comments.
I tried sending patch 2 with Carlo as "From:", however the mail provider replaced this with my default mail address. I checked with my other mail providers, they also allow only sender addresses belonging to me.
Quoted 5 lines
IIRC putting "From: Carlo Caione <[email protected]>" as the first line in the commit log makes git set the patch author accordingly during "git am" (regardless of what is in the "From:" header of the email).
Thanks for the hint. Indeed that's what the git am docu says:
"From: " and "Subject: " lines starting the body override the respective commit author name and title values taken from the headers.
Patchwork doesn't seem to be that smart ..
Quoted 3 lines
HTH,
Karsten
PATCH v3 2/3 mmc: meson: add MMC driver for Meson GX (S905)
Am 02.02.2017 um 20:41 schrieb Heiner Kallweit:
Quoted 30 lines
Am 02.02.2017 um 20:33 schrieb Karsten Merker:
Quoted 24 lines · Heiner Kallweit
Quoted 14 lines
Am 31.01.2017 um 14:24 schrieb Jaehoon Chung:
Quoted 13 lines · Heiner Kallweit
Quoted 8 lines
This driver implements MMC support on Meson GX (S905) based systems. It's based on Carlo Caione's work, changes:
- BLK support added
- general refactoringSigned-off-by Carlo Caione <[email protected]>Signed-off-by Andreas F?rber <[email protected]>Signed-off-by Heiner Kallweit <[email protected]>Andreas's comment is what this patch's author is Carlo..Not just add Signed-off tag for Carlo.
Quoted 8 lines
Quoted 3 lines
When you send the email, needs to add "From: Carlo Caione <[email protected]>", not yours.
I sent a v4 series addressing the review comments.
I tried sending patch 2 with Carlo as "From:", however the mail provider replaced this with my default mail address. I checked with my other mail providers, they also allow only sender addresses belonging to me.Quoted 5 lines
IIRC putting "From: Carlo Caione <[email protected]>" as the first line in the commit log makes git set the patch author accordingly during "git am" (regardless of what is in the "From:" header of the email).
Quoted 5 lines
Thanks for the hint. Indeed that's what the git am docu says:
"From: " and "Subject: " lines starting the body override the respective commit author name and title values taken from the headers.
Patchwork doesn't seem to be that smart ..
I believe I already pointed you to the --author command line option?
git commit --amend --author="Carlo ... <...>"
Regards,
Andreas
Signature · 3 lines
SUSE Linux GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany GF: Felix Imend?rffer, Jane Smithard, Graham Norton HRB 21284 (AG N?rnberg)
PATCH v3 3/3 odroid-c2: enable new Meson GX MMC driver in board defconfig
In reply to a message not in the archiveEnable new Meson GX MMC driver in Odroid C2 defconfig.
---
v2:
- move GXBB_PINMUX definition from patch 3 to this one v3:
- remove pinmux configuration in board init and use pinctrl driver instead
--- configs/odroid-c2_defconfig | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
configs/odroid-c2_defconfig +4 -1
@@ -3,7 +3,9 @@ CONFIG_ARCH_MESON=y CONFIG_MESON_GXBB=y CONFIG_TARGET_ODROID_C2=y CONFIG_IDENT_STRING=" odroid-c2" -# CONFIG_MMC is not set +CONFIG_MMC=y +CONFIG_DM_MMC=y +CONFIG_MMC_MESON_GX=y CONFIG_DEFAULT_DEVICE_TREE="meson-gxbb-odroidc2" # CONFIG_DISPLAY_CPUINFO is not set # CONFIG_DISPLAY_BOARDINFO is not set
@@ -14,6 +16,7 @@ CONFIG_HUSH_PARSER=y # CONFIG_CMD_LOADS is not set # CONFIG_CMD_FPGA is not set # CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_MMC=y CONFIG_OF_CONTROL=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_DM_ETH=y
Signature · 1 line
2.11.0
PATCH v3 3/3 odroid-c2: enable new Meson GX MMC driver in board defconfig
Hi Heiner,
Quoted 1 line · Heiner Kallweit
Enable new Meson GX MMC driver in Odroid C2 defconfig.
Conflicts this patch on latest u-boot.
Best Regards,
Jaehoon Chung
Quoted 36 lines
Signed-off-by Heiner Kallweit <[email protected]>---
v2:
- moveGXBB_PINMUXdefinition from patch 3 to this one v3:
- remove pinmux configuration in board init and use pinctrl driver instead--- configs/odroid-c2_defconfig | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)configs/odroid-c2_defconfig +4
-1@@ -3,7 +3,9 @@ CONFIG_ARCH_MESON=y CONFIG_MESON_GXBB=y CONFIG_TARGET_ODROID_C2=y CONFIG_IDENT_STRING=" odroid-c2" -# CONFIG_MMC is not set +CONFIG_MMC=y +CONFIG_DM_MMC=y +CONFIG_MMC_MESON_GX=y CONFIG_DEFAULT_DEVICE_TREE="meson-gxbb-odroidc2" # CONFIG_DISPLAY_CPUINFO is not set # CONFIG_DISPLAY_BOARDINFO is not set@@ -14,6 +16,7 @@ CONFIG_HUSH_PARSER=y # CONFIG_CMD_LOADS is not set # CONFIG_CMD_FPGA is not set # CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_MMC=y CONFIG_OF_CONTROL=y CONFIG_NET_RANDOM_ETHADDR=y CONFIG_DM_ETH=y