Skip to contentSkip to conversation

Data abort when starting DFU on SAMA5D2

DISCUSSION Alexis Lothoré 3 participants 4 messages Aug 1, 2023 – Aug 3, 2023

lore
Share & tools
lore
#0 lore raw

Hi,
I am currently using an ATSAMA5D27-WLSOM1-EK1. This boards embeds an ATSAMA5D27-WLSOM1, which in turns holds an ATSAMA5D27 and a 8MB QSPI flash. I have been wanting to program u-boot in the QSPI flash thanks to DFU, since the board is able to boot from QSPI and is supported in uboot. To do so, I have executed the following steps:
- check out recent uboot version (2023.07.02, but issed described below is observed on master too)
- load sama5d27_wlsom1_ek_qspiflash_defconfig
- tune the configuration to enable DFU:
- CONFIG_CMD_DFU=y
- CONFIG_DFU_SF=y
- CONFIG_USB_GADGET_DOWNLOAD=y
- build uboot, upload and run it onto external ram thanks to snagrecover ([1]).
- running "bdinfo" shows that board is properly defined/recognized
- "sf probe" properly detects the qspi flash chip
- in u-boot console, configure dfu:
- setenv dfu_alt_info uboot raw 0 0x80000
- start DFU:
- dfu 0 sf 2:0

Unfortunately, this step systematically and immediately leads to a data abort with the following log:

=> dfu 0 sf 2:0
data abort

pc : [<2fda9ee0>]	   lr : [<2fd8dc08>]

reloc pc : [<26f3fee0>]lr : [<26f23c08>]
sp : 2f963fe8 ip : 2f9829cc fp : 00000000
r10: 2fde1cd9 r9 : 2f969e80 r8 : 2fdfc304
r7 : 00000000 r6 : 00000000 r5 : 2fdf3034 r4 : 2f982948
r3 : 0a299cfc r2 : ffffffec r1 : 00000000 r0 : 00000000
Flags: nzCv IRQs off FIQs off Mode SVC_32

Code: e5843058 e5950004 e3a01000 e5903008 (e5933008)

Resetting CPU ...

resetting ...
System reset not supported on this platform
### ERROR ### Please RESET the board ###

A quick translation with addr2line shows that the data abort occurs in include/linux/usb/gagdet.h, in usb_ep_alloc_request, likely because of ep being NULL, which seems confirmed by adding some custom logs in both usb_ep_alloc_request and its caller (composite_bind). Before digging further, does anyone have successfully used DFU on SAMA5D2 boards (and if so, am I missing something in the configuration) ? Or does this data abort show that some support is still missing to make it work for SAMA5D2 ?

Kind regards,
Alexis

[1] https://github.com/bootlin/snagboot

Signature · 3 lines
Alexis Lothoré, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
#1 lore raw

Hi Alexis,

Quoted 40 lines · Alexis Lothoré

Hi,
I am currently using an ATSAMA5D27-WLSOM1-EK1. This boards embeds an ATSAMA5D27-WLSOM1, which in turns holds an ATSAMA5D27 and a 8MB QSPI flash. I have been wanting to program u-boot in the QSPI flash thanks to DFU, since the board is able to boot from QSPI and is supported in uboot. To do so, I have executed the following steps:
- check out recent uboot version (2023.07.02, but issed described below is observed on master too)
- load sama5d27_wlsom1_ek_qspiflash_defconfig
- tune the configuration to enable DFU:
- CONFIG_CMD_DFU=y
- CONFIG_DFU_SF=y
- CONFIG_USB_GADGET_DOWNLOAD=y
- build uboot, upload and run it onto external ram thanks to snagrecover ([1]).
- running "bdinfo" shows that board is properly defined/recognized
- "sf probe" properly detects the qspi flash chip
- in u-boot console, configure dfu:
- setenv dfu_alt_info uboot raw 0 0x80000
- start DFU:
- dfu 0 sf 2:0

Unfortunately, this step systematically and immediately leads to a data abort with the following log:

=> dfu 0 sf 2:0
data abort

pc : [<2fda9ee0>]	   lr : [<2fd8dc08>]

reloc pc : [<26f3fee0>]lr : [<26f23c08>]
sp : 2f963fe8 ip : 2f9829cc fp : 00000000
r10: 2fde1cd9 r9 : 2f969e80 r8 : 2fdfc304
r7 : 00000000 r6 : 00000000 r5 : 2fdf3034 r4 : 2f982948
r3 : 0a299cfc r2 : ffffffec r1 : 00000000 r0 : 00000000
Flags: nzCv IRQs off FIQs off Mode SVC_32

Code: e5843058 e5950004 e3a01000 e5903008 (e5933008)

Resetting CPU ...

resetting ...
System reset not supported on this platform
### ERROR ### Please RESET the board ###

Quoted 7 lines

A quick translation with addr2line shows that the data abort occurs in include/linux/usb/gagdet.h, in usb_ep_alloc_request, likely because of ep being NULL, which seems confirmed by adding some custom logs in both usb_ep_alloc_request and its caller (composite_bind). Before digging further, does anyone have successfully used DFU on SAMA5D2 boards (and if so, am I missing something in the configuration) ? Or does this data abort show that some support is still missing to make it work for SAMA5D2 ?

I believe this is related to the gadget more than DFU itself. Zixun LI (in CC) has attempted gadget on this platform at some point.

Mihai (also in CC) has did some tests with USB on this platform as well. Cristian has more knowledge of the USB implementation on sama5d2.

Eugen

Quoted 5 lines

Kind regards,
Alexis

[1] https://github.com/bootlin/snagboot

#2 lore raw

Hi Alexis,

I've tried to USB gardet under u-boot without success (linux is ok).

I've contacted Microchip support (No.01275010) and from them:
"we confirmed with the internal team that USB is not fully functional with u-boot so for any query related to working of USB in u-boot we request you to create a NASCAR."

Regards,
Zixun

Quoted 75 lines · Eugen Hristev

Hi Alexis,

Quoted 3 lines · Alexis Lothoré

Hi,
I am currently using an ATSAMA5D27-WLSOM1-EK1. This boards embeds an ATSAMA5D27-WLSOM1, which in turns holds an ATSAMA5D27 and a 8MB QSPI

flash. I

Quoted 1 line

have been wanting to program u-boot in the QSPI flash thanks to DFU,

since the

Quoted 1 line

board is able to boot from QSPI and is supported in uboot. To do so, I

have

Quoted 2 lines

executed the following steps:
- check out recent uboot version (2023.07.02, but issed described below

is

Quoted 7 lines

observed on master too)
- load sama5d27_wlsom1_ek_qspiflash_defconfig
- tune the configuration to enable DFU:
- CONFIG_CMD_DFU=y
- CONFIG_DFU_SF=y
- CONFIG_USB_GADGET_DOWNLOAD=y
- build uboot, upload and run it onto external ram thanks to snagrecover

([1]).

Quoted 8 lines

- running "bdinfo" shows that board is properly defined/recognized
- "sf probe" properly detects the qspi flash chip
- in u-boot console, configure dfu:
- setenv dfu_alt_info uboot raw 0 0x80000
- start DFU:
- dfu 0 sf 2:0

Unfortunately, this step systematically and immediately leads to a data

abort

Quoted 12 lines

with the following log:

=> dfu 0 sf 2:0
data abort

pc : [<2fda9ee0>]        lr : [<2fd8dc08>]

reloc pc : [<26f3fee0>]lr : [<26f23c08>]
sp : 2f963fe8 ip : 2f9829cc fp : 00000000
r10: 2fde1cd9 r9 : 2f969e80 r8 : 2fdfc304
r7 : 00000000 r6 : 00000000 r5 : 2fdf3034 r4 : 2f982948
r3 : 0a299cfc r2 : ffffffec r1 : 00000000 r0 : 00000000
Flags: nzCv IRQs off FIQs off Mode SVC_32

Code: e5843058 e5950004 e3a01000 e5903008 (e5933008)
Quoted 8 lines

Resetting CPU ...

resetting ...
System reset not supported on this platform
### ERROR ### Please RESET the board ###

A quick translation with addr2line shows that the data abort occurs in include/linux/usb/gagdet.h, in usb_ep_alloc_request, likely because of

ep being

Quoted 2 lines

NULL, which seems confirmed by adding some custom logs in both usb_ep_alloc_request and its caller (composite_bind). Before digging

further,

Quoted 2 lines

does anyone have successfully used DFU on SAMA5D2 boards (and if so, am I missing something in the configuration) ? Or does this data abort show

that some

Quoted 1 line

support is still missing to make it work for SAMA5D2 ?

I believe this is related to the gadget more than DFU itself. Zixun LI (in CC) has attempted gadget on this platform at some point.

Mihai (also in CC) has did some tests with USB on this platform as well. Cristian has more knowledge of the USB implementation on sama5d2.

Eugen

Quoted 5 lines

Kind regards,
Alexis

[1] https://github.com/bootlin/snagboot

#3 lore raw

Hello Zixun, Eugen,

Quoted 8 lines · admin LI

Hi  Alexis,

I've tried to USB gardet under u-boot without success (linux is ok).

I've contacted Microchip support (No.01275010) and from them:
"we confirmed with the internal team that USB is not fully functional with u-boot so for any query related to working of USB in u-boot we request you to create a NASCAR."

Thanks for the feedback and the status confirmation. I fell back with sam-ba for the moment

Kind regards,

Quoted 75 lines

Regards,
Zixun

On Wed, Aug 2, 2023 at 9:11 AM Eugen Hristev <[email protected] <mailto:[email protected]>> wrote:

Hi Alexis,

On 8/1/23 10:09, Alexis Lothoré wrote:
> Hi,
> I am currently using an ATSAMA5D27-WLSOM1-EK1. This boards embeds an > ATSAMA5D27-WLSOM1, which in turns holds an ATSAMA5D27 and a 8MB QSPI flash. I > have been wanting to program u-boot in the QSPI flash thanks to DFU, since the > board is able to boot from QSPI and is supported in uboot. To do so, I have > executed the following steps:
> - check out recent uboot version (2023.07.02, but issed described below is > observed on master too)
> - load sama5d27_wlsom1_ek_qspiflash_defconfig
> - tune the configuration to enable DFU:
>    - CONFIG_CMD_DFU=y
>    - CONFIG_DFU_SF=y
>    - CONFIG_USB_GADGET_DOWNLOAD=y
> - build uboot, upload and run it onto external ram thanks to snagrecover ([1]).
>    - running "bdinfo" shows that board is properly defined/recognized >    - "sf probe" properly detects the qspi flash chip
> - in u-boot console, configure dfu:
>    - setenv dfu_alt_info uboot raw 0 0x80000
> - start DFU:
>    - dfu 0 sf 2:0
>
> Unfortunately, this step systematically and immediately leads to a data abort > with the following log:
>
> => dfu 0 sf 2:0
> data abort
> pc : [<2fda9ee0>]        lr : [<2fd8dc08>]
> reloc pc : [<26f3fee0>]lr : [<26f23c08>]
> sp : 2f963fe8  ip : 2f9829cc   fp : 00000000
> r10: 2fde1cd9  r9 : 2f969e80   r8 : 2fdfc304
> r7 : 00000000  r6 : 00000000   r5 : 2fdf3034  r4 : 2f982948
> r3 : 0a299cfc  r2 : ffffffec   r1 : 00000000  r0 : 00000000
> Flags: nzCv  IRQs off  FIQs off  Mode SVC_32
> Code: e5843058 e5950004 e3a01000 e5903008 (e5933008)
> Resetting CPU ...
>
> resetting ...
> System reset not supported on this platform
> ### ERROR ### Please RESET the board ###
>
> A quick translation with addr2line shows that the data abort occurs in > include/linux/usb/gagdet.h, in usb_ep_alloc_request, likely because of ep being
> NULL, which seems confirmed by adding some custom logs in both
> usb_ep_alloc_request and its caller (composite_bind). Before digging further, > does anyone have successfully used DFU on SAMA5D2 boards (and if so, am I > missing something in the configuration) ? Or does this data abort show that some
> support is still missing to make it work for SAMA5D2 ?

I believe this is related to the gadget more than DFU itself. Zixun LI (in CC) has attempted gadget on this platform at some point.

Mihai (also in CC) has did some tests with USB on this platform as well. Cristian has more knowledge of the USB implementation on sama5d2.

Eugen

>
> Kind regards,
> Alexis
>
> [1] https://github.com/bootlin/snagboot <https://github.com/bootlin/snagboot>

Signature · 3 lines
Alexis Lothoré, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com