Skip to contentSkip to conversation

Problems with large amount of partitions on SD

DISCUSSION Mauro Condarelli 1 participant 1 message Oct 2, 2020

lore
Share & tools
lore
#0 lore raw

I am having huge problems with my system *possibly* due to fact I have 10 partitions on a single SD card.

I'm getting an unreliable behavior (issuing the same commands do *not* result in consistent behavior) which *seem* to point to some overwrite/cache problem.

First of all: is a configuration with 10 partitions on SD supported?
I tried perusing files in disk/part*, but I failed to see where extended partitions are handled.

Here follows one (typical) example:

This is one example of a boot after a long time off, no key touched:
================================================================================

Quoted 27 lines

U-Boot SPL 2020.10-rc5 (Oct 01 2020 - 17:14:04 +0200) Trying to boot from NOR

U-Boot 2020.10-rc5 (Oct 01 2020 - 17:14:04 +0200)

CPU:   MediaTek MT7628A ver:1 eco:2
Boot:  DDR2, SPI-NOR 3-Byte Addr, CPU clock from XTAL
Clock: CPU: 580MHz, Bus: 193MHz, XTAL: 40MHz
DRAM:  128 MiB
WDT:   Started with servicing (60s timeout)
MMC:   mmc at 10130000: 0
Loading Environment from SPIFlash... SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
OK
In:    uart2 at e00
Out:   uart2 at e00
Err:   uart2 at e00
Model: VoCore2

Net:
Warning: eth at 10110000 (eth0) using random MAC address - 0a:92:ae:d0:9b:c2
eth0: eth at 10110000
Hit any key to stop autoboot: 0
Loading System B

Partition Map for MMC device 0 -- Partition Type: DOS

Part Start Sector Num Sectors UUID Type

Quoted 8 lines
  1	2048      	262144    	30f8737b-01	0c
  2	264192    	4194304   	30f8737b-02	83
  3	4458496   	32768     	30f8737b-03	83
  4	4491264   	11268096  	30f8737b-04	05 Extd

** Can't read partition table on 0:4491264 **
** Can't read partition table on 0:4902912 **
** Invalid partition 7 **
Loading Recovery

================================================================================
here recovery system is loaded from Flash, not mmc. After a "reboot" from linux I get:
================================================================================

Quoted 21 lines
[48634.981029] reboot: Restarting system
[48634.984764] ralink_restart

U-Boot SPL 2020.10-rc5 (Oct 01 2020 - 17:14:04 +0200) Trying to boot from NOR

U-Boot 2020.10-rc5 (Oct 01 2020 - 17:14:04 +0200)

CPU:   MediaTek MT7628A ver:1 eco:2
Boot:  DDR2, SPI-NOR 3-Byte Addr, CPU clock from XTAL
Clock: CPU: 580MHz, Bus: 193MHz, XTAL: 40MHz
DRAM:  128 MiB
WDT:   Started with servicing (60s timeout)
MMC:   mmc at 10130000: 0
Loading Environment from SPIFlash... SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
OK
In:    uart2 at e00
Out:   uart2 at e00
Err:   uart2 at e00
Model: VoCore2
Quoted 4 lines

Net:
Warning: eth at 10110000 (eth0) using random MAC address - be:c5:7e:06:ca:a1
eth0: eth at 10110000
Hit any key to stop autoboot: 0

================================================================================
Here I stop autoboot.
This is my complete environment.
================================================================================

Quoted 32 lines

=> printenv
BOOT_CURRENT=B
SYSTEM_R=/dev/mtdblock5
arch=mips
baudrate=115200
board=vocore2
board_name=vocore2
boot_a=echo "Loading System A";part=6;run boot_x
boot_b=echo "Loading System B";part=7;run boot_x
boot_now=if test "${BOOT_CURRENT}" = A; then run boot_a; elif test "${BOOT_CURRENT}" = B; then run boot_b; fi; if env exists BOOT_A_GOOD; then run boot_a; fi; if env exists BOOT_B_GOOD; then run boot_b; fi; run boot_r boot_r=echo "Loading Recovery"; setenv bootargs "${default_bootargs} mtdparts=${mtdparts} root=/dev/mtdblock5"; bootm bc050000
boot_x=mmc rescan && mmc part && ls mmc 0:${part} && load mmc 0:${part} 85000000 /boot/uImage && setenv bootargs "${default_bootargs} mtdparts=${mtdparts} root=/dev/mmcblk0p${part}" && bootm ${fileaddr} bootcmd=mmc rescan && sleep 1 && run do_boot
bootcount=1
bootdelay=2
cpu=mips32
default_bootargs=earlyprintk rootwait console=ttyS2,115200
do_boot=test ${bootcount} -gt 1 && run remove_boot; run boot_now
fdtcontroladdr=86f6d350
fileaddr=85000000
filesize=268c63
fupdate=mmc rescan && load mmc 0:1 84000000 uboot.scr && fatrm mmc 0:1 uboot.scr && source 84000000 && echo Flash updated
mtdids=nor0=spi0.0
mtdparts=spi0.0:312k(u-boot),4k(env),4k(factory),2368k(kernel),-(filesystem)
remove_boot=if env exists BOOT_CURRENT; then setenv BOOT_CURRENT; saveenv; elif env exists BOOT_A_GOOD; then setenv BOOT_A_GOOD; saveenv; elif env exists BOOT_B_GOOD; then setenv BOOT_B_GOOD; saveenv; fi soc=mt7628
stderr=uart2 at e00
stdin=uart2 at e00
stdout=uart2 at e00
vendor=vocore
ver=U-Boot 2020.10-rc5 (Oct 01 2020 - 17:14:04 +0200)

Quoted 1 line

Environment size: 1558/4092 bytes

================================================================================
I have two full systems on SD (partitions 6 and 7) and a fallback on Flash. Idea is to try to boot from BOOT_CURRENT System, if possible, fallback to the other, if "GOOD" and boot Recovery as last resort.
I modified "boot_x"to do some printouts before booting (first 3 commands) Here I manually start "B" system boot:
================================================================================

Quoted 35 lines

=> run boot_b
Loading System B

Partition Map for MMC device 0 -- Partition Type: DOS

Part Start Sector Num Sectors UUID Type

  1	2048      	262144    	30f8737b-01	0c
  2	264192    	4194304   	30f8737b-02	83
  3	4458496   	32768     	30f8737b-03	83
  4	4491264   	11268096  	30f8737b-04	05 Extd
  5	4493312   	409600    	30f8737b-05	83
  6	4904960   	102400    	30f8737b-06	83
  7	5009408   	102400    	30f8737b-07	83
  8	5113856   	102400    	30f8737b-08	83
  9	5218304   	102400    	30f8737b-09	83
 10	5322752   	4194304   	30f8737b-0a	83
            bin/
            boot/
            dev/
            etc/
            lib/
    <SYM>   lib32
            media/
            mnt/
            opt/
            over/
            proc/
            root/
            run/
            sbin/
            sys/
            tmp/
            usr/
            var/
Quoted 4 lines

1 file(s), 17 dir(s)

Error: too many data blocks to be read.
Failed to load '/boot/uImage'

================================================================================
... which fails in a different way.
I do again the same command (nothing in between)
================================================================================

Quoted 35 lines

=> run boot_b
Loading System B

Partition Map for MMC device 0 -- Partition Type: DOS

Part Start Sector Num Sectors UUID Type

  1	2048      	262144    	30f8737b-01	0c
  2	264192    	4194304   	30f8737b-02	83
  3	4458496   	32768     	30f8737b-03	83
  4	4491264   	11268096  	30f8737b-04	05 Extd
  5	4493312   	409600    	30f8737b-05	83
  6	4904960   	102400    	30f8737b-06	83
  7	5009408   	102400    	30f8737b-07	83
  8	5113856   	102400    	30f8737b-08	83
  9	5218304   	102400    	30f8737b-09	83
 10	5322752   	4194304   	30f8737b-0a	83
            bin/
            boot/
            dev/
            etc/
            lib/
    <SYM>   lib32
            media/
            mnt/
            opt/
            over/
            proc/
            root/
            run/
            sbin/
            sys/
            tmp/
            usr/
            var/
Quoted 6 lines

1 file(s), 17 dir(s)

2526307 bytes read in 260 ms (9.3 MiB/s)
## Booting kernel from Legacy Image at 85000000 ...
Image Name: Linux-5.8.0
Image Type: MIPS Linux Kernel Image (gzip compressed)

================================================================================
... and it succeeds.

I originally blamed this to my tweaks to SquashFS (part 6 and 7 are SquashFS), but it seems problem happens at partition level, before filesystem is touched.

Please advise.
Mauro