Skip to contentSkip to conversation

why can't I DNAT SIP?

DISCUSSION sean darcy 5 participants 14 messages May 8, 2008 – May 12, 2008

lore
Share & tools
lore

sean darcy

author
#0 lore raw

On my outside box I trying to route sip ( port 5060 ) and iax ( 4659 ) packets to an internal asterisk server. I use DNAT, which works fine for
iax, but doesn't for SIP. I'm using identical DNAT statments.

The log shows the SIP packets coming in, but then going to the INPUT chain. Nothing shows up on the FORWARD chain.

iptables -L -n -v -t nat
Chain PREROUTING (policy ACCEPT 168K packets, 17M bytes)
pkts bytes target prot opt in out source
destination

    0     0 DNAT       udp  --  external *       0.0.0.0/0 
0.0.0.0/0           udp dpt:4569 to:10.10.10.180:4569
    0     0 DNAT       udp  --  external *       0.0.0.0/0 
0.0.0.0/0           udp dpts:10000:10100 to:10.10.10.180
    0     0 DNAT       udp  --  external *       0.0.0.0/0 

0.0.0.0/0 udp dpt:5060 to:10.10.10.180:5060

Chain POSTROUTING (policy ACCEPT 3098 packets, 298K bytes)
pkts bytes target prot opt in out source
destination

    0     0 LOG        udp  --  *      lan     0.0.0.0/0 
0.0.0.0/0           udp dpt:5060 LOG flags 0 level 4 prefix `SIP-POST: '
    5   268 SNAT       all  --  *      external  0.0.0.0/0 

0.0.0.0/0 to:xxx.yyy.zzz.ooo

IPT=/sbin/iptables

# first, flush all chains
/sbin/iptables -F
/sbin/iptables -t nat -F
$IPT -t raw -F
/sbin/iptables -X

# log SIP packets

$IPT -t raw -A PREROUTING -p udp --dport 5060 -s ext-box -j LOG --log-prefix "GATEWAY: "

$IPT  -A FORWARD -p udp --dport 5060 -s ext-box  -j LOG --log-prefix "SIP-FWD:    "
$IPT  -A INPUT -p udp --dport 5060 -s ext-box  -j LOG --log-prefix "SIP-INPUT:    "

$IPT -t nat -A POSTROUTING -s 76.248.148.160 -p udp --dport 5060 -j LOG --log-prefix "SIP-POST: "

## DNAT iax packets

$IPT -t nat -A PREROUTING -i external -p udp --dport 4569 -j DNAT --to 10.10.10.180:4569 $IPT -A FORWARD -p udp -m state --state NEW -d 10.10.10.180 --dport 4569 -j ACCEPT

# this should do the same for sip

$IPT -t nat -A PREROUTING -s ext-box -p udp --dport 5060 -j DNAT --to 10.10.10.180:5060 $IPT -A FORWARD -p udp --dport 5060 -m state --state NEW -d 10.10.10.180 -j ACCEPT

.............

The log shows SIP packets both at GATEWAY and SIP-INPUT.

Any help appreciated.

sean

#1 lore raw
Quoted 1 line · sean darcy

On my outside box I trying to route sip ( port 5060 ) and iax ( 4659 ) packets to an internal asterisk server. I use DNAT, which works fine for iax, but doesn't for SIP. I'm using identical DNAT statments.

No you are not.

Quoted 1 line

$IPT -t nat -A PREROUTING -i external -p udp --dport 4569 -j DNAT --to 10.10.10.180:4569

(verses)

Quoted 1 line

$IPT -t nat -A PREROUTING -s ext-box -p udp --dport 5060 -j DNAT --to 10.10.10.180:5060

Note that you have "-i external" on the first (IAX) rule and "-s ext-box" on the second (SIP) rule.

I don't know if you have taken this in to account or not, but remember that SIP is not really NAT friendly.

Grant. . . .

author
#2 lore raw
Quoted 5 lines · Grant Taylor
Quoted 1 line · sean darcy

On my outside box I trying to route sip ( port 5060 ) and iax ( 4659 ) packets to an internal asterisk server. I use DNAT, which works fine for iax, but doesn't for SIP. I'm using identical DNAT statments.

No you are not.

Quoted 8 lines
Quoted 1 line

$IPT -t nat -A PREROUTING -i external -p udp --dport 4569 -j DNAT --to 10.10.10.180:4569

(verses)

Quoted 1 line

$IPT -t nat -A PREROUTING -s ext-box -p udp --dport 5060 -j DNAT --to 10.10.10.180:5060

Note that you have "-i external" on the first (IAX) rule and "-s ext-box" on the second (SIP) rule.

I tried it both ways. FWIW, it works both ways for iax. I showed it that way because the LOG statement were that way. I've run them all both ways.

Quoted 2 lines

I don't know if you have taken this in to account or not, but remember that SIP is not really NAT friendly.

Yeah, but why is iptables not filtering the packet correctly; it's just a port 5060 udp packet. How can it matter that it's 5060 instead of 4569?

Here it comes in -t raw -A PREROUTING:

GATEWAY: IN=external OUT= MAC=00:48:54:8b:ab:29:00:1a:e2:84:bf:3b:08:00 SRC=xxx.yyy.148.160 DST=yyy.xxx.167.178 LEN=527 TOS=0x04 PREC=0x00 TTL=48 ID=32417 PROTO=UDP SPT=5060 DPT=5060 LEN=507

either:
$IPT -t nat -A PREROUTING -s ext-box -p udp --dport 5060 -j DNAT --to 10.10.10.180:5060

or:

$IPT -t nat -A PREROUTING -i external -p udp --dport 5060 -j DNAT --to 10.10.10.180:5060

should send the packet to the FORWARD chain, but instead it shows up in INPUT:

SIP-INPUT: IN=external OUT= MAC=00:48:54:8b:ab:29:00:1a:e2:84:bf:3b:08:00 SRC=xxx.yyy.148.160 DST=yyyy.xxx.167.178 LEN=527 TOS=0x04 PREC=0x00 TTL=48 ID=32417 PROTO=UDP SPT=5060 DPT=5060 LEN=507

?????

#13 lore raw
In reply to sean darcy
Quoted 13 lines · sean darcy

On my outside box I trying to route sip ( port 5060 ) and iax ( 4659 ) packets to an internal asterisk server. I use DNAT, which works fine for
iax, but doesn't for SIP. I'm using identical DNAT statments.

The log shows the SIP packets coming in, but then going to the INPUT chain. Nothing shows up on the FORWARD chain.

iptables -L -n -v -t nat
Chain PREROUTING (policy ACCEPT 168K packets, 17M bytes)
pkts bytes target prot opt in out source destination

    0     0 DNAT       udp  --  external *       0.0.0.0/0 
0.0.0.0/0           udp dpt:4569 to:10.10.10.180:4569
    0     0 DNAT       udp  --  external *       0.0.0.0/0 
0.0.0.0/0           udp dpts:10000:10100 to:10.10.10.180
    0     0 DNAT       udp  --  external *       0.0.0.0/0 
Quoted 9 lines

0.0.0.0/0 udp dpt:5060 to:10.10.10.180:5060

Chain POSTROUTING (policy ACCEPT 3098 packets, 298K bytes)

 pkts bytes target     prot opt in     out     source destination
    0     0 LOG        udp  --  *      lan     0.0.0.0/0 
0.0.0.0/0           udp dpt:5060 LOG flags 0 level 4 prefix `SIP-POST: '
    5   268 SNAT       all  --  *      external  0.0.0.0/0 

0.0.0.0/0 to:xxx.yyy.zzz.ooo

I've found it very helpful to look at the rules as output by the command "iptables-save". It's formatted nicely and in order of evaluation. If there are errors they are easier to spot (at least for me).

my 2p

author
#3 lore raw
In reply to sean darcy
Quoted 33 lines · sean darcy
Quoted 8 lines · Grant Taylor
Quoted 1 line · sean darcy

On my outside box I trying to route sip ( port 5060 ) and iax ( 4659 ) packets to an internal asterisk server. I use DNAT, which works fine for iax, but doesn't for SIP. I'm using identical DNAT statments.

No you are not.

Quoted 2 lines

$IPT -t nat -A PREROUTING -i external -p udp --dport 4569 -j DNAT --to 10.10.10.180:4569

Quoted 7 lines

(verses)

Quoted 2 lines

$IPT -t nat -A PREROUTING -s ext-box -p udp --dport 5060 -j DNAT --to 10.10.10.180:5060

Note that you have "-i external" on the first (IAX) rule and "-s ext-box" on the second (SIP) rule.

I tried it both ways. FWIW, it works both ways for iax. I showed it that way because the LOG statement were that way. I've run them all both ways.

Quoted 2 lines

I don't know if you have taken this in to account or not, but remember that SIP is not really NAT friendly.

Yeah, but why is iptables not filtering the packet correctly; it's just a port 5060 udp packet. How can it matter that it's 5060 instead of 4569?

Here it comes in -t raw -A PREROUTING:

GATEWAY: IN=external OUT= MAC=00:48:54:8b:ab:29:00:1a:e2:84:bf:3b:08:00 SRC=xxx.yyy.148.160 DST=yyy.xxx.167.178 LEN=527 TOS=0x04 PREC=0x00 TTL=48 ID=32417 PROTO=UDP SPT=5060 DPT=5060 LEN=507

either:
$IPT -t nat -A PREROUTING -s ext-box -p udp --dport 5060 -j DNAT --to 10.10.10.180:5060

or:

Quoted 9 lines

$IPT -t nat -A PREROUTING -i external -p udp --dport 5060 -j DNAT --to 10.10.10.180:5060

should send the packet to the FORWARD chain, but instead it shows up in INPUT:

SIP-INPUT: IN=external OUT= MAC=00:48:54:8b:ab:29:00:1a:e2:84:bf:3b:08:00 SRC=xxx.yyy.148.160 DST=yyyy.xxx.167.178 LEN=527 TOS=0x04 PREC=0x00 TTL=48 ID=32417 PROTO=UDP SPT=5060 DPT=5060 LEN=507

?????

AFAICS, ports 4569 and 5060 should both be FORWARD'ed:

+ /sbin/iptables -v -t nat -A PREROUTING -i external -p udp --dport 4569 -j DNAT --to 10.10.10.180:4569 DNAT udp opt -- in external out * 0.0.0.0/0 -> 0.0.0.0/0 udp dpt:4569 to:10.10.10.180:4569
+ /sbin/iptables -v -A FORWARD -p udp -m state --state NEW -d 10.10.10.180 --dport 4569 -j ACCEPT ACCEPT udp opt -- in * out * 0.0.0.0/0 -> 10.10.10.180 state NEW udp dpt:4569
+ /sbin/iptables -v -t nat -A PREROUTING -i external -p udp --dport 5060 -j DNAT --to 10.10.10.180:5060 DNAT udp opt -- in external out * 0.0.0.0/0 -> 0.0.0.0/0 udp dpt:5060 to:10.10.10.180:5060
+ /sbin/iptables -v -A FORWARD -p udp --dport 5060 -m state --state NEW -d 10.10.10.180 -j ACCEPT ACCEPT udp opt -- in * out * 0.0.0.0/0 -> 10.10.10.180 udp dpt:5060 state NEW

sean

#4 lore raw
In reply to sean darcy
Quoted 3 lines · sean darcy

I tried it both ways. FWIW, it works both ways for iax. I showed it that way because the LOG statement were that way. I've run them all both ways.

Yeah, but why is iptables not filtering the packet correctly; it's just a port 5060 udp packet. How can it matter that it's 5060 instead of 4569?

With out knowing the full scenario, I can't say for sure. Are you dealing with an on going established connection, thus one that is not passing through the NAT chain again?

Is it possible that you are dealing with SIP Reinvited traffic that really has a source of elsewhere?

More things are starting to come in to play.

Grant. . . .

#5 lore raw
Quoted 10 lines · Grant Taylor
Quoted 3 lines · sean darcy

I tried it both ways. FWIW, it works both ways for iax. I showed it that way because the LOG statement were that way. I've run them all both ways.

Yeah, but why is iptables not filtering the packet correctly; it's just a port 5060 udp packet. How can it matter that it's 5060 instead of 4569?

With out knowing the full scenario, I can't say for sure. Are you dealing with an on going established connection, thus one that is not passing through the NAT chain again?

Is it possible that you are dealing with SIP Reinvited traffic that really has a source of elsewhere?

More things are starting to come in to play.

Some questions that might help answering this:

- Which kernel version are you running?

- What helpers are loaded (both NAT and conntrack)

- How does the entry from /proc/net/nf_conntrack for the SIP connection look like?

author
#6 lore raw
Quoted 14 lines · Patrick McHardy
Quoted 13 lines · Grant Taylor
Quoted 6 lines · sean darcy

I tried it both ways. FWIW, it works both ways for iax. I showed it that way because the LOG statement were that way. I've run them all both ways.

Yeah, but why is iptables not filtering the packet correctly; it's just a port 5060 udp packet. How can it matter that it's 5060 instead of 4569?

With out knowing the full scenario, I can't say for sure. Are you dealing with an on going established connection, thus one that is not passing through the NAT chain again?

Quoted 8 lines
Quoted 4 lines

Is it possible that you are dealing with SIP Reinvited traffic that really has a source of elsewhere?

More things are starting to come in to play.

Some questions that might help answering this:

- Which kernel version are you running?

2.6.22

Quoted 2 lines

- What helpers are loaded (both NAT and conntrack)

?? How would I find out? If you mean modules:

lsmod | grep nat

iptable_nat            11461  1
nf_nat                 22381  1 iptable_nat
nf_conntrack_ipv4      21837  5 iptable_nat
nf_conntrack           64585  4 xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4
nfnetlink               9945  3 nf_nat,nf_conntrack_ipv4,nf_conntrack
ip_tables              16517  3 iptable_raw,iptable_nat,iptable_filter
x_tables               18629  5 xt_state,ipt_LOG,xt_tcpudp,iptable_nat,ip_tables
Quoted 4 lines

- How does the entry from /proc/net/nf_conntrack for the SIP connection look like?

OK. It's sunspots. Just got back to this now, and it's working:

GATEWAY: IN=external OUT=
MAC=00:48:54:8b:ab:29:00:1a:e2:84:bf:3b:08:00 SRC=xxx.yyy.144.110 DST=yyy.xxx.167.178 LEN=576 TOS=0x04 PREC=0x00 TTL=49 ID=8130 PROTO=UDP SPT=5060 DPT=5060 LEN=556
SIP-FWD: IN=external OUT=lan SRC=xxx.yyy.144.110 DST=10.10.10.180
LEN=576 TOS=0x04 PREC=0x00 TTL=48 ID=8130 PROTO=UDP SPT=5060 DPT=5060 LEN=556

Thanks for all the help. I certainly know a lot more about debugging iptables.

FWIW, here's the entry from /proc/net/nf_conntrack:

ipv4 2 udp 17 161 src=xxx.yyy.144.110 dst=yyy.xxx.167.178
sport=5060 dport=5060 packets=1288 bytes=693472 src=10.10.10.180 dst=xxx.yyy.144.110 sport=5060 dport=5060 packets=1783 bytes=884951 [ASSURED] mark=0 secmark=0 use=1

Is this telling me there's an ESTABLISHED connection? So somehow a sip packet that was NEW got in, and the ACK made iptables set it up? If so, it works now as long as they keep ACKing each other, but if I try a new sip connection, for instance from the road, I'll have the same issue?

sean

#7 lore raw
Quoted 5 lines · sean darcy
Quoted 2 lines

- What helpers are loaded (both NAT and conntrack)

?? How would I find out? If you mean modules:

Quoted 8 lines

lsmod | grep nat

iptable_nat            11461  1
nf_nat                 22381  1 iptable_nat
nf_conntrack_ipv4      21837  5 iptable_nat
nf_conntrack           64585  4 xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4
nfnetlink               9945  3 nf_nat,nf_conntrack_ipv4,nf_conntrack
ip_tables              16517  3 iptable_raw,iptable_nat,iptable_filter
x_tables               18629  5 xt_state,ipt_LOG,xt_tcpudp,iptable_nat,ip_tables

I would have expected to find nf_nat_sip here.

author
#8 lore raw
Quoted 13 lines · Jan Engelhardt
Quoted 11 lines · sean darcy
Quoted 1 line

- What helpers are loaded (both NAT and conntrack)

?? How would I find out? If you mean modules:

lsmod | grep nat

iptable_nat            11461  1
nf_nat                 22381  1 iptable_nat
nf_conntrack_ipv4      21837  5 iptable_nat
nf_conntrack           64585  4 xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4
nfnetlink               9945  3 nf_nat,nf_conntrack_ipv4,nf_conntrack
ip_tables              16517  3 iptable_raw,iptable_nat,iptable_filter
x_tables               18629  5 xt_state,ipt_LOG,xt_tcpudp,iptable_nat,ip_tables
Quoted 2 lines

I would have expected to find nf_nat_sip here.
--

I've seen references to nf_nat_sip, but no docs, howto or examples. What does it do that simple port forwarding doesn't? and how do you use it?

sean

#9 lore raw
Quoted 3 lines · sean darcy

I've seen references to nf_nat_sip, but no docs, howto or examples. What does it do that simple port forwarding doesn't? and how do you use it?

It modifies the SIP packets to contain the correct address when you happen to NAT connections.

author
#10 lore raw
Quoted 7 lines · Jan Engelhardt
Quoted 2 lines · sean darcy

I've seen references to nf_nat_sip, but no docs, howto or examples. What does it do that simple port forwarding doesn't? and how do you use it?

It modifies the SIP packets to contain the correct address when you happen to NAT connections.
--

Any examples on how to use it?

I even went and read the source. Sigh.

sean

#11 lore raw
Quoted 10 lines · sean darcy
Quoted 7 lines · Jan Engelhardt
Quoted 3 lines · sean darcy

I've seen references to nf_nat_sip, but no docs, howto or examples. What does
it do that simple port forwarding doesn't? and how do you use it?

It modifies the SIP packets to contain the correct address when you happen to NAT connections.

Any examples on how to use it?

Just load it.

#12 lore raw
In reply to sean darcy
Quoted 39 lines · sean darcy
Quoted 11 lines · Patrick McHardy
Quoted 10 lines · Grant Taylor
Quoted 5 lines · sean darcy

I tried it both ways. FWIW, it works both ways for iax. I showed it that way because the LOG statement were that way. I've run them all both ways.

Yeah, but why is iptables not filtering the packet correctly; it's just a port 5060 udp packet. How can it matter that it's 5060 instead of 4569?

With out knowing the full scenario, I can't say for sure. Are you dealing with an on going established connection, thus one that is not passing through the NAT chain again?

Quoted 7 lines
Quoted 4 lines

Is it possible that you are dealing with SIP Reinvited traffic that really has a source of elsewhere?

More things are starting to come in to play.

Some questions that might help answering this:

- Which kernel version are you running?

2.6.22

Quoted 1 line

- What helpers are loaded (both NAT and conntrack)

?? How would I find out? If you mean modules:

lsmod | grep nat

iptable_nat            11461  1
nf_nat                 22381  1 iptable_nat
nf_conntrack_ipv4      21837  5 iptable_nat
nf_conntrack           64585  4 xt_state,iptable_nat,nf_nat,nf_conntrack_ipv4
nfnetlink               9945  3 nf_nat,nf_conntrack_ipv4,nf_conntrack
ip_tables              16517  3 iptable_raw,iptable_nat,iptable_filter
x_tables               18629  5 xt_state,ipt_LOG,xt_tcpudp,iptable_nat,ip_tables
Quoted 3 lines

- How does the entry from /proc/net/nf_conntrack for the SIP connection look like?

OK. It's sunspots. Just got back to this now, and it's working:

Quoted 7 lines

GATEWAY: IN=external OUT=
MAC=00:48:54:8b:ab:29:00:1a:e2:84:bf:3b:08:00 SRC=xxx.yyy.144.110 DST=yyy.xxx.167.178 LEN=576 TOS=0x04 PREC=0x00 TTL=49 ID=8130 PROTO=UDP SPT=5060 DPT=5060 LEN=556
SIP-FWD: IN=external OUT=lan SRC=xxx.yyy.144.110 DST=10.10.10.180
LEN=576 TOS=0x04 PREC=0x00 TTL=48 ID=8130 PROTO=UDP SPT=5060 DPT=5060 LEN=556

That would indicate that a conntrack entry already existed when the first packet arrived from the outside. I'm guessing that it arrived before the DNAT rules were set up. Adding:

conntrack -F

to the end of your firewall-script should make sure that it works reliably.