Skip to contentSkip to conversation

EC168 "dvb_usb: Unknown symbol release_firmware"

DISCUSSION drbob 3 participants 6 messages May 4, 2009 – May 5, 2009 Media (V4L/DVB)

lore
Share & tools
lore

drbob

author
#0 lore raw

Hello,

I recently tried to build and use the EC168 drivers from
<http://linuxtv.org/hg/~anttip/ec168/>
following instructions found at
<http://www.dealextreme.com/forums/Default.dx/sku.8325~threadid.278942>

The drivers built fine but upon trying to load dvb-usb.ko (sudo insmod ./dvb-usb.ko) I got the following error:

insmod: error inserting './dvb-usb.ko': -1 Unknown symbol in module

dmesg listed these additonal errors:

  [  647.189929] dvb_usb: Unknown symbol release_firmware
  [  647.190085] dvb_usb: Unknown symbol request_firmware

I am running Debian 5.0 with the stock kernel (2.6.26-2-amd64) on an HP ML115 server (Quad-Core AMD Opteron(tm) Processor 1352, 4GB ECC memory)

I found I was able to work around the issue like so:

1. First load and then unload the stock dvb-core and dvb-usb included with lenny.

sudo modprobe dvb-core
sudo modprobe dvb-usb
sudo rmmod dvb-core
sudo rmmod dvb-usb

2. Then load the modules built from the EC168 tree.

sudo insmod ./dvb-core.ko
sudo insmod ./dvb-usb.ko
sudo insmod ./ec100.ko
sudo insmod ./mxl5005s.ko
sudo insmod ./dvb-usb-ec168.ko

The stick then works and I can use it to view tv etc, unplug/reinsert it and unload/reload the EC168 tree modules without carrying out step 1 again (until the next reboot).

The stick is a cheap generic USB stick purchased from eBay (USB id 18b4:1001). Photos of it are here:

<http://img89.imageshack.us/gal.php?g=img1283g.jpg>

Strangely the markings on the large main chip appear to have been removed by the stick manufacturer (though I think it must be an EC168) The smaller tuner chip has also been scrubbed but the following markings can still be identified:

Maxline MXL5003
D37T5:1

Thanks for your time.

author
#2 lore raw
Quoted 3 lines · CityK

drbob,

Off_Topic: that name takes me back: http://muppet.wikia.com/wiki/Dr._Bob

And I thought I'd picked that name at random. The muppets must have had a deeper effect on my subconscious than I realised...

Quoted 5 lines

On_Topic: You have built the drivers but you haven't installed them into the system as intended, consequently you will run into the set of observations that you have. Have a read through:
http://www.linuxtv.org/wiki/index.php/How_to_Obtain%

2C_Build_and_Install_V4L-DVB_Device_Drivers

Thanks for the link. It put me on the right track. I needed to load the "firmware-class" kernel module before dvb-usb - modprobe resolves module dependencies automatically, insmod does not. dvb-usb also relies on i2c_core but that was already loaded on my system.

So to manually load the ec168 modules I need to execute:

sudo modprobe firmware-class

Bdefore the the insmod commands.

For testing purposes I wanted to explicity load the new modules with insmod rather than install them and overwrite all the modules included with the kernel, which I know have been passed as stable. That seemed more sensible than the course of action suggested by the wiki article.

#3 lore raw
In reply to drbob
Quoted 9 lines · drbob

The stick is a cheap generic USB stick purchased from eBay (USB id 18b4:1001). Photos of it are here:

<http://img89.imageshack.us/gal.php?g=img1283g.jpg>

Strangely the markings on the large main chip appear to have been removed by the stick manufacturer (though I think it must be an EC168) The smaller tuner chip has also been scrubbed but the following markings can still be identified:

I have just same stick, it is EC168 + MXL5003.

I haven't opened my stick but looked your pictures. I have never seen so bad soldering quality :o

Driver development is a little bit freeze currently due to lack of EC168 specs. If you can provide specs please contact me!

regards
Antti

Signature · 1 line
http://palosaari.fi/
author
#4 lore raw
Quoted 3 lines · Antti Palosaari

I haven't opened my stick but looked your pictures. I have never seen so bad soldering quality :o

Yeah it's pretty bad. I was pretty surprised it works at all when I saw it as in several places component terminals or chip pins appear to be bridged.

Quoted 4 lines

Driver development is a little bit freeze currently due to lack of EC168 specs. If you can provide specs please contact me!

No specs here, I'm just an end user, but a translated google search (english->chinese) for "ec168 dvb" threw up this page:

<http://detail.cn.china.cn/provide/detail,1347758640.html>
<http://translate.google.com/translate?prev=hp&hl=en&js=n&u=http%3A%2F%2Fdetail.cn.china.cn%2Fprovide%2Fdetail%2C1347758640.html&sl=zh-CN&tl=en>

I think it's a company in China selling a reference design and tech support to potential manufacturers, so they probably have the tech docs. Good luck if you fancy trying to get a response from them.

author
#5 lore raw
Quoted 15 lines · drbob
Quoted 2 lines · Antti Palosaari

I haven't opened my stick but looked your pictures. I have never seen so bad soldering quality :o

Yeah it's pretty bad. I was pretty surprised it works at all when I saw it as in several places component terminals or chip pins appear to be bridged.

Quoted 4 lines

Driver development is a little bit freeze currently due to lack of EC168 specs. If you can provide specs please contact me!

Quoted 5 lines

No specs here, I'm just an end user, but a translated google search (english->chinese) for "ec168 dvb" threw up this page:

<http://detail.cn.china.cn/provide/detail,1347758640.html>
<http://translate.google.com/translate?prev=hp&hl=en&js=n&u=http%3A%2F%

2Fdetail.cn.china.cn%2Fprovide%2Fdetail%2C1347758640.html&sl=zh-CN&tl=en>

Quoted 4 lines

I think it's a company in China selling a reference design and tech support to potential manufacturers, so they probably have the tech docs. Good luck if you fancy trying to get a response from them.

After a little further digging I think the company that orignally designed the ec168 is probably defunct. I found a US address and contact number for the company here:

<http://www.soccentral.com/results.asp?EntryID=23118>

However the phone line has been disconnected. As per the wiki, their web page has also disappeared.