Messages are printed on screen
Subsystems (2)
Hi All,
i am setting up my Server, with Linux Debian lenny. Therefore i am using
Kernel 2.6.31.1. I configured this Kernel with <make defconfig> and
<make menuconfig>. My motherboard has 5 PCI slots and 1 AGP slot. All slots are in use. All devices are mapped to the following IRQ-Line:
Mass Storage Device (PCI Slot1) IRQ-Line 11
Ethernet (PCI Slot 2) IRQ-Line 4
Ethernet (PCI Slot 3) IRQ-Line 5
Ethernet (PCI Slot 4) IRQ-Line 7
Ethernet (PCI Slot 5) IRQ-Line 11
Onboard USB-Controller IRQ-Line 5
Onboard USB-Controller IRQ-Line 4
Onboard USB-Controller IRQ-Line 11
Onboard IDE IRQ-Line 14
AGP VGA IRQ-Line 11
As you see some of my IRQ-Lines are multiply in use, so my Server is working hard at his limit. The result is sometimes freezing of my Server, especially if there is much processing on these devices. I remember that with Kernel 2.6.18 my system didn't does freezing.
So i am trying to reduce the amount of this processing. I still get messages about dropped network packets on my Terminal, although i set up my <rsyslog> to save this only to </var/log>. Here is my </etc/rsyslog.conf>
How can i disable the output of messages (about dropped packets from my firewall) to my terminal ?
How can i stabilize my IRQ-System with the kernel 2.6.31.1 ?
What debug features should i disable ?
regards Markus
Quoted 4 lines · Markus Feldmann
Hi All,
i am setting up my Server, with Linux Debian lenny. Therefore i am using
Kernel 2.6.31.1.
The current kernel version for 'lenny' is 2.6.26 (with stable updates and other fixes).
2.6.31 is known to have a large number of regressions outstanding, which is why it is not in Debian yet.
Quoted 15 lines
I configured this Kernel with <make defconfig> and
<make menuconfig>. My motherboard has 5 PCI slots and 1 AGP slot. All slots are in use. All devices are mapped to the following IRQ-Line:Mass Storage Device (PCI Slot1) IRQ-Line 11
Ethernet (PCI Slot 2) IRQ-Line 4
Ethernet (PCI Slot 3) IRQ-Line 5
Ethernet (PCI Slot 4) IRQ-Line 7
Ethernet (PCI Slot 5) IRQ-Line 11
Onboard USB-Controller IRQ-Line 5
Onboard USB-Controller IRQ-Line 4
Onboard USB-Controller IRQ-Line 11
Onboard IDE IRQ-Line 14
AGP VGA IRQ-Line 11
Quoted 2 lines
As you see some of my IRQ-Lines are multiply in use, so my Server is working hard at his limit.
IRQ sharing is normal on PCs without MSI support, but to see where that's happening you need to look at /proc/interrupts and not the BIOS setup program or wherever you got the above information from.
This does not result in 'working hard at his limit'.
Quoted 3 lines
The result is sometimes freezing of my
Server, especially if there is much processing on these devices. I remember that with Kernel 2.6.18 my system didn't does freezing.
This is simply a bug, not a result of IRQ sharing or 'working hard'.
Quoted 4 lines
So i am trying to reduce the amount of this processing. I still get messages about dropped network packets on my Terminal, although i set up my <rsyslog> to save this only to <
/var/log>. Here is my </etc/rsyslog.conf>
You forgot to paste it.
Quoted 2 lines
How can i disable the output of messages (about dropped packets from my firewall) to my terminal ?
Edit the value of kernel.printk in /etc/sysctl.conf.
Quoted 1 line
How can i stabilize my IRQ-System with the kernel 2.6.31.1 ?
I would expect the standard kernel version for 'lenny' or the 2.6.30 kernel from 'sid' to be more stable.
Quoted 1 line
What debug features should i disable ?
No idea, you didn't even specify what you enabled...
Ben.
Signature · 2 lines
Ben Hutchings Who are all these weirdos? - David Bowie, about L-Space IRC channel #afp
Quoted 8 lines · Ben Hutchings
Quoted 2 lines · Markus Feldmann
As you see some of my IRQ-Lines are multiply in use, so my Server is working hard at his limit.
IRQ sharing is normal on PCs without MSI support, but to see where that's happening you need to look at
/proc/interruptsand not the BIOS setup program or wherever you got the above information from.
Ok i did <cat /proc/interrupts> and got:
CPU0
0: 259603 XT-PIC-XT timer 1: 1421 XT-PIC-XT i8042 2: 0 XT-PIC-XT cascade 4: 200000 XT-PIC-XT ohci_hcd:usb3, pppp0 5: 0 XT-PIC-XT ehci_hcd:usb1, lan0 7: 6959 XT-PIC-XT lan1 8: 2 XT-PIC-XT rtc0 9: 0 XT-PIC-XT acpi 11: 37697 XT-PIC-XT ide2, ide3, ohci_hcd:usb2, lan2 14: 0 XT-PIC-XT ide0 NMI: 0 Non-maskable interrupts TRM: 0 Thermal event interrupts MCE: 0 Machine check exceptions MCP: 13 Machine check polls ERR: 2
How can i assigned IRQs during Boot?
How can i watch which IRQ Line has most traffic or problems ?
Quoted 3 lines
Quoted 1 line
The result is sometimes freezing of my Server, especially if there is much processing on these devices. I remember that with Kernel 2.6.18 my system didn't does freezing.
This is simply a bug, not a result of IRQ sharing or 'working hard'.
But something had initiated this freezing. Although i do not know the Bug, i should be able to avoide this Problem by do some prevention ?!
Quoted 4 lines
Quoted 2 lines
How can i disable the output of messages (about dropped packets from my firewall) to my terminal ?
Edit the value of kernel.printk in
/etc/sysctl.conf.
Ok i did add:
kernel.printk= 4 4 1 7
to </etc/sysctl.conf>
Quoted 5 lines
Quoted 2 lines
How can i stabilize my IRQ-System with the kernel 2.6.31.1 ?
I would expect the standard kernel version for 'lenny' or the 2.6.30 kernel from 'sid' to be more stable.
Ok i will try the kernel from Debian Sid. :-)
Quoted 4 lines
Quoted 2 lines
What debug features should i disable ?
No idea, you didn't even specify what you enabled...
I will add some enabled features next week.
regards Markus
Quoted 10 lines · Markus Feldmann
Quoted 9 lines · Ben Hutchings
Quoted 3 lines · Markus Feldmann
As you see some of my IRQ-Lines are multiply in use, so my Server is working hard at his limit.
IRQ sharing is normal on PCs without MSI support, but to see where that's happening you need to look at
/proc/interruptsand not the BIOS setup program or wherever you got the above information from.
Quoted 6 lines
Ok i did <cat
/proc/interrupts> and got:
CPU00: 259603 XT-PIC-XT timer 1: 1421 XT-PIC-XT i8042 2: 0 XT-PIC-XT cascade 4: 200000 XT-PIC-XT ohci_hcd:usb3, pppp0
This number is a clue because after every 100,000 interrupts for a particular IRQ the kernel checks how many of them were handled. If this is less than 100 then it disables the IRQ. So I suspect one of these devices is misbehaving, or its driver is not handling interrupts correctly. Is 'pppp0' actually an Ethernet device that you're using for PPPoE? If so, what model of network card is it?
Quoted 12 lines
5: 0 XT-PIC-XT ehci_hcd:usb1, lan0 7: 6959 XT-PIC-XT lan1 8: 2 XT-PIC-XT rtc0 9: 0 XT-PIC-XT acpi 11: 37697 XT-PIC-XT ide2, ide3, ohci_hcd:usb2, lan2 14: 0 XT-PIC-XT ide0 NMI: 0 Non-maskable interrupts TRM: 0 Thermal event interrupts MCE: 0 Machine check exceptions MCP: 13 Machine check polls ERR: 2
Quoted 1 line
How can i assigned IRQs during Boot?
[...]
They are assigned by the BIOS. You may be able to configure this in BIOS setup.
Ben.
Signature · 2 lines
Ben Hutchings Who are all these weirdos? - David Bowie, about L-Space IRC channel #afp
Quoted 2 lines · Markus Feldmann
....
my <rsyslog> to save this only to </var/log>. Here is my </etc/rsyslog.conf>