Skip to contentSkip to conversation

e1000e: NIC not working (after resume?)

DISCUSSION Frederik Himpe 2 participants 5 messages Sep 9, 2011

lore
Share & tools
lore
#0 lore raw

I have a Dell Latitude E6400 which has a network card supported by the e1000e driver. Often (I think after a suspend/resume cycle), the network card does not work at all: the NIC is correctly seen by ifconfig, but running ethtool just returns: "No such device". dhclient -v gives the impression that it's correctly sending out DHCPDISCOVER packets on the NIC, but a tcpdump running on the same machine does not see any packets going out.

I'm using Debian's 3.0.0-3 kernel (corresponding with Linux 3.0.3).

Full lspci, .config and dmesg output at
http://artipc10.vub.ac.be/~frederik/e1000e/

Here is some relevant summary.

How can I find out what is going wrong?

# ifconfig eth0
eth0      Link encap:Ethernet  HWaddr 00:21:70:e1:bb:4c  
          UP BROADCAST PROMISC MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:22 Memory:f6ae0000-f6b00000 
# ethtool eth0
Settings for eth0:
Cannot get device settings: No such device
Cannot get wake-on-lan settings: No such device
Cannot get message level: No such device
Cannot get link status: No such device
No data available
# lspci -vvnn
00:19.0 Ethernet controller [0200]: Intel Corporation 82567LM Gigabit Network Connection [8086:10f5] (rev 03)
        Subsystem: Dell Device [1028:0233]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin A routed to IRQ 22
        Region 0: Memory at f6ae0000 (32-bit, non-prefetchable) [disabled] [size=128K]
        Region 1: Memory at f6adb000 (32-bit, non-prefetchable) [disabled] [size=4K]
        Region 2: I/O ports at efe0 [disabled] [size=32]
        Capabilities: [c8] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=1 PME+
        Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
                Address: 00000000fee0300c  Data: 4182
        Capabilities: [e0] PCI Advanced Features
                AFCap: TP+ FLR+
                AFCtrl: FLR-
                AFStatus: TP-
        Kernel driver in use: e1000e
# dmesg | grep -E "e1000e|eth0"
[    1.027437] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
[    1.027441] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[    1.027480] e1000e 0000:00:19.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    1.027491] e1000e 0000:00:19.0: setting latency timer to 64
[    1.027605] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[    1.231440] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:21:70:e1:bb:4c
[    1.231444] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[    1.231470] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: 1004FF-0FF
[   22.896268] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[   22.952097] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[   22.954132] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   24.504903] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[   24.506413] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[   24.508402] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   34.788022] eth0: no IPv6 routers present
[   41.444922] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[   41.446325] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[25136.918393] e1000e 0000:00:19.0: PME# enabled
[25142.488050] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[25142.488058] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[25142.488066] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[25142.488085] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[25142.488110] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[25142.488167] e1000e 0000:00:19.0: PME# disabled
[25142.510966] e1000e 0000:00:19.0: PCI INT A disabled
[25142.510971] e1000e 0000:00:19.0: PME# enabled
[25143.468668] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[25143.468689] e1000e 0000:00:19.0: restoring config space at offset 0x6 (was 0x1, writing 0xefe1)
[25143.468696] e1000e 0000:00:19.0: restoring config space at offset 0x5 (was 0x0, writing 0xf6adb000)
[25143.468703] e1000e 0000:00:19.0: restoring config space at offset 0x4 (was 0x0, writing 0xf6ae0000)
[25143.468713] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[25143.471149] e1000e 0000:00:19.0: PME# disabled
[25143.471277] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[25145.276441] e1000e 0000:00:19.0: PME# enabled
[25146.082051] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[25146.082076] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[25146.082090] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[25146.082126] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[25146.082169] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[25146.082280] e1000e 0000:00:19.0: PME# disabled
[25146.176605] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[25146.232228] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[25146.234003] ADDRCONF(NETDEV_UP): eth0: link is not ready
[25147.328875] e1000e 0000:00:19.0: PME# enabled
[26261.896126] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26261.896140] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26261.896149] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26261.896169] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26261.896196] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26261.896241] e1000e 0000:00:19.0: PME# disabled
[26261.896316] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26261.972148] e1000e 0000:00:19.0: PME# enabled
[26268.192160] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26268.192168] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26268.192175] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26268.192194] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26268.192219] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26268.192274] e1000e 0000:00:19.0: PME# disabled
[26268.213875] e1000e 0000:00:19.0: PME# enabled
[26269.172481] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26269.172497] e1000e 0000:00:19.0: restoring config space at offset 0x6 (was 0x1, writing 0xefe1)
[26269.172502] e1000e 0000:00:19.0: restoring config space at offset 0x5 (was 0x0, writing 0xf6adb000)
[26269.172507] e1000e 0000:00:19.0: restoring config space at offset 0x4 (was 0x0, writing 0xf6ae0000)
[26269.172515] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26269.174262] e1000e 0000:00:19.0: PME# disabled
[26269.174339] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26272.384806] e1000e 0000:00:19.0: PME# enabled
[26274.688310] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26275.482490] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26276.277343] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26277.075194] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26277.870807] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26278.667881] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26279.463492] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26280.258982] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26281.056598] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26281.855386] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26282.649838] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26283.445674] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26289.848036] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26289.848044] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26289.848050] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26289.848067] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26289.848090] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26289.848146] e1000e 0000:00:19.0: PME# disabled
[26289.940279] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26289.996092] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26289.996761] ADDRCONF(NETDEV_UP): eth0: link is not ready
[26291.088343] e1000e 0000:00:19.0: PME# enabled
[26900.272077] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26900.272096] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26900.272111] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26900.272142] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26900.272180] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26900.272250] e1000e 0000:00:19.0: PME# disabled
[26900.272379] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26900.274426] e1000e 0000:00:19.0: eth0: MAC Wakeup cause - Link Status Change
[26905.560584] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
[26905.560591] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[26905.560650] e1000e 0000:00:19.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[26905.560665] e1000e 0000:00:19.0: setting latency timer to 64
[26905.560836] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26905.744547] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:21:70:e1:bb:4c
[26905.744552] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[26905.744581] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: 1004FF-0FF
[26905.744594] e1000e 0000:00:19.0: PME# enabled
[26905.880141] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26905.880149] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26905.880155] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26905.880172] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26905.880194] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26905.880247] e1000e 0000:00:19.0: PME# disabled
[26905.968320] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26906.024395] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26906.025907] ADDRCONF(NETDEV_UP): eth0: link is not ready
[26907.112415] e1000e 0000:00:19.0: PME# enabled
[27308.975856] device eth0 entered promiscuous mode
[27326.414382] device eth0 left promiscuous mode
[27336.815362] device eth0 entered promiscuous mode

* Right after start up: machine is in docking station, network is working fine.
* At 25136: resume machine, not in docking station, no network cable plugged in, so network connection was not tested.
* At 26261: resume machine, in docking station, network cable plugged in, but network connection is not working
* At 26900: rmmod e1000e && modprobe e1000e: network still not working

Signature · 1 line
Frederik Himpe
#1 lore raw

[Crossposting to e1000 mailing list]

I have a Dell Latitude E6400 which has a network card supported by the e1000e driver. Often (I think after a suspend/resume cycle), the network card does not work at all: the NIC is correctly seen by ifconfig, but running ethtool just returns: "No such device". dhclient -v gives the impression that it's correctly sending out DHCPDISCOVER packets on the NIC, but a tcpdump running on the same machine does not see any packets going out.

I'm using Debian's 3.0.0-3 kernel (corresponding with Linux 3.0.3).

Full lspci, .config and dmesg output at
http://artipc10.vub.ac.be/~frederik/e1000e/

Here is some relevant summary.

How can I find out what is going wrong?

# ifconfig eth0
eth0      Link encap:Ethernet  HWaddr 00:21:70:e1:bb:4c  
          UP BROADCAST PROMISC MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:22 Memory:f6ae0000-f6b00000 
# ethtool eth0
Settings for eth0:
Cannot get device settings: No such device
Cannot get wake-on-lan settings: No such device
Cannot get message level: No such device
Cannot get link status: No such device
No data available
# lspci -vvnn
00:19.0 Ethernet controller [0200]: Intel Corporation 82567LM Gigabit Network Connection [8086:10f5] (rev 03)
        Subsystem: Dell Device [1028:0233]
        Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin A routed to IRQ 22
        Region 0: Memory at f6ae0000 (32-bit, non-prefetchable) [disabled] [size=128K]
        Region 1: Memory at f6adb000 (32-bit, non-prefetchable) [disabled] [size=4K]
        Region 2: I/O ports at efe0 [disabled] [size=32]
        Capabilities: [c8] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=1 PME+
        Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
                Address: 00000000fee0300c  Data: 4182
        Capabilities: [e0] PCI Advanced Features
                AFCap: TP+ FLR+
                AFCtrl: FLR-
                AFStatus: TP-
        Kernel driver in use: e1000e
# dmesg | grep -E "e1000e|eth0"
[    1.027437] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
[    1.027441] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[    1.027480] e1000e 0000:00:19.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    1.027491] e1000e 0000:00:19.0: setting latency timer to 64
[    1.027605] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[    1.231440] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:21:70:e1:bb:4c
[    1.231444] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[    1.231470] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: 1004FF-0FF
[   22.896268] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[   22.952097] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[   22.954132] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   24.504903] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[   24.506413] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[   24.508402] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   34.788022] eth0: no IPv6 routers present
[   41.444922] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[   41.446325] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[25136.918393] e1000e 0000:00:19.0: PME# enabled
[25142.488050] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[25142.488058] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[25142.488066] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[25142.488085] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[25142.488110] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[25142.488167] e1000e 0000:00:19.0: PME# disabled
[25142.510966] e1000e 0000:00:19.0: PCI INT A disabled
[25142.510971] e1000e 0000:00:19.0: PME# enabled
[25143.468668] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[25143.468689] e1000e 0000:00:19.0: restoring config space at offset 0x6 (was 0x1, writing 0xefe1)
[25143.468696] e1000e 0000:00:19.0: restoring config space at offset 0x5 (was 0x0, writing 0xf6adb000)
[25143.468703] e1000e 0000:00:19.0: restoring config space at offset 0x4 (was 0x0, writing 0xf6ae0000)
[25143.468713] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[25143.471149] e1000e 0000:00:19.0: PME# disabled
[25143.471277] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[25145.276441] e1000e 0000:00:19.0: PME# enabled
[25146.082051] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[25146.082076] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[25146.082090] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[25146.082126] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[25146.082169] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[25146.082280] e1000e 0000:00:19.0: PME# disabled
[25146.176605] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[25146.232228] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[25146.234003] ADDRCONF(NETDEV_UP): eth0: link is not ready
[25147.328875] e1000e 0000:00:19.0: PME# enabled
[26261.896126] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26261.896140] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26261.896149] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26261.896169] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26261.896196] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26261.896241] e1000e 0000:00:19.0: PME# disabled
[26261.896316] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26261.972148] e1000e 0000:00:19.0: PME# enabled
[26268.192160] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26268.192168] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26268.192175] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26268.192194] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26268.192219] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26268.192274] e1000e 0000:00:19.0: PME# disabled
[26268.213875] e1000e 0000:00:19.0: PME# enabled
[26269.172481] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26269.172497] e1000e 0000:00:19.0: restoring config space at offset 0x6 (was 0x1, writing 0xefe1)
[26269.172502] e1000e 0000:00:19.0: restoring config space at offset 0x5 (was 0x0, writing 0xf6adb000)
[26269.172507] e1000e 0000:00:19.0: restoring config space at offset 0x4 (was 0x0, writing 0xf6ae0000)
[26269.172515] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26269.174262] e1000e 0000:00:19.0: PME# disabled
[26269.174339] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26272.384806] e1000e 0000:00:19.0: PME# enabled
[26274.688310] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26275.482490] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26276.277343] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26277.075194] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26277.870807] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26278.667881] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26279.463492] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26280.258982] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26281.056598] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26281.855386] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26282.649838] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26283.445674] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26289.848036] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26289.848044] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26289.848050] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26289.848067] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26289.848090] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26289.848146] e1000e 0000:00:19.0: PME# disabled
[26289.940279] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26289.996092] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26289.996761] ADDRCONF(NETDEV_UP): eth0: link is not ready
[26291.088343] e1000e 0000:00:19.0: PME# enabled
[26900.272077] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26900.272096] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26900.272111] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26900.272142] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26900.272180] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26900.272250] e1000e 0000:00:19.0: PME# disabled
[26900.272379] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26900.274426] e1000e 0000:00:19.0: eth0: MAC Wakeup cause - Link Status Change
[26905.560584] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
[26905.560591] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[26905.560650] e1000e 0000:00:19.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[26905.560665] e1000e 0000:00:19.0: setting latency timer to 64
[26905.560836] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26905.744547] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:21:70:e1:bb:4c
[26905.744552] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[26905.744581] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: 1004FF-0FF
[26905.744594] e1000e 0000:00:19.0: PME# enabled
[26905.880141] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26905.880149] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26905.880155] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26905.880172] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26905.880194] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26905.880247] e1000e 0000:00:19.0: PME# disabled
[26905.968320] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26906.024395] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26906.025907] ADDRCONF(NETDEV_UP): eth0: link is not ready
[26907.112415] e1000e 0000:00:19.0: PME# enabled
[27308.975856] device eth0 entered promiscuous mode
[27326.414382] device eth0 left promiscuous mode
[27336.815362] device eth0 entered promiscuous mode

* Right after start up: machine is in docking station, network is working fine.
* At 25136: resume machine, not in docking station, no network cable plugged in, so network connection was not tested.
* At 26261: resume machine, in docking station, network cable plugged in, but network connection is not working
* At 26900: rmmod e1000e && modprobe e1000e: network still not working

Signature · 1 line
Frederik Himpe
#2 lore raw
Quoted 37 lines · Frederik Himpe

[Crossposting to e1000 mailing list]

I have a Dell Latitude E6400 which has a network card supported by the e1000e driver. Often (I think after a suspend/resume cycle), the network card does not work at all: the NIC is correctly seen by ifconfig, but running ethtool just returns: "No such device". dhclient -v gives the impression that it's correctly sending out DHCPDISCOVER packets on the NIC, but a tcpdump running on the same machine does not see any packets going out.

I'm using Debian's 3.0.0-3 kernel (corresponding with Linux 3.0.3).

Full lspci, .config and dmesg output at
http://artipc10.vub.ac.be/~frederik/e1000e/

Here is some relevant summary.

How can I find out what is going wrong?

# ifconfig eth0
eth0      Link encap:Ethernet  HWaddr 00:21:70:e1:bb:4c
         UP BROADCAST PROMISC MULTICAST  MTU:1500  Metric:1
         RX packets:0 errors:0 dropped:0 overruns:0 frame:0
         TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
         collisions:0 txqueuelen:1000
         RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
         Interrupt:22 Memory:f6ae0000-f6b00000
# ethtool eth0
Settings for eth0:
Cannot get device settings: No such device
Cannot get wake-on-lan settings: No such device
Cannot get message level: No such device
Cannot get link status: No such device
No data available
Quoted 12 lines
# lspci -vvnn
00:19.0 Ethernet controller [0200]: Intel Corporation 82567LM Gigabit Network Connection [8086:10f5] (rev 03)
       Subsystem: Dell Device [1028:0233]
       Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
       Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
       Interrupt: pin A routed to IRQ 22
       Region 0: Memory at f6ae0000 (32-bit, non-prefetchable) [disabled] [size=128K]
       Region 1: Memory at f6adb000 (32-bit, non-prefetchable) [disabled] [size=4K]
       Region 2: I/O ports at efe0 [disabled] [size=32]
       Capabilities: [c8] Power Management version 2
               Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
               Status: D3 NoSoftRst- PME-Enable+ DSel=0 DScale=1 PME+

The above is why nothing seems to work right. The kernel runtime power management thinks there is no link on the port, and so is putting the port into D3. We need to make sure that our driver wakes the device to read link state (the problem is that wake from D3, plus time to get link can take ~4 seconds).

Quoted 130 lines

       Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
               Address: 00000000fee0300c  Data: 4182
       Capabilities: [e0] PCI Advanced Features
               AFCap: TP+ FLR+
               AFCtrl: FLR-
               AFStatus: TP-
       Kernel driver in use: e1000e

# dmesg | grep -E "e1000e|eth0"
[    1.027437] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
[    1.027441] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[    1.027480] e1000e 0000:00:19.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    1.027491] e1000e 0000:00:19.0: setting latency timer to 64
[    1.027605] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[    1.231440] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:21:70:e1:bb:4c
[    1.231444] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[    1.231470] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: 1004FF-0FF
[   22.896268] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[   22.952097] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[   22.954132] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   24.504903] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[   24.506413] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[   24.508402] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   34.788022] eth0: no IPv6 routers present
[   41.444922] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[   41.446325] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[25136.918393] e1000e 0000:00:19.0: PME# enabled
[25142.488050] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[25142.488058] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[25142.488066] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[25142.488085] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[25142.488110] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[25142.488167] e1000e 0000:00:19.0: PME# disabled
[25142.510966] e1000e 0000:00:19.0: PCI INT A disabled
[25142.510971] e1000e 0000:00:19.0: PME# enabled
[25143.468668] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[25143.468689] e1000e 0000:00:19.0: restoring config space at offset 0x6 (was 0x1, writing 0xefe1)
[25143.468696] e1000e 0000:00:19.0: restoring config space at offset 0x5 (was 0x0, writing 0xf6adb000)
[25143.468703] e1000e 0000:00:19.0: restoring config space at offset 0x4 (was 0x0, writing 0xf6ae0000)
[25143.468713] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[25143.471149] e1000e 0000:00:19.0: PME# disabled
[25143.471277] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[25145.276441] e1000e 0000:00:19.0: PME# enabled
[25146.082051] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[25146.082076] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[25146.082090] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[25146.082126] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[25146.082169] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[25146.082280] e1000e 0000:00:19.0: PME# disabled
[25146.176605] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[25146.232228] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[25146.234003] ADDRCONF(NETDEV_UP): eth0: link is not ready
[25147.328875] e1000e 0000:00:19.0: PME# enabled
[26261.896126] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26261.896140] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26261.896149] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26261.896169] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26261.896196] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26261.896241] e1000e 0000:00:19.0: PME# disabled
[26261.896316] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26261.972148] e1000e 0000:00:19.0: PME# enabled
[26268.192160] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26268.192168] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26268.192175] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26268.192194] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26268.192219] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26268.192274] e1000e 0000:00:19.0: PME# disabled
[26268.213875] e1000e 0000:00:19.0: PME# enabled
[26269.172481] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26269.172497] e1000e 0000:00:19.0: restoring config space at offset 0x6 (was 0x1, writing 0xefe1)
[26269.172502] e1000e 0000:00:19.0: restoring config space at offset 0x5 (was 0x0, writing 0xf6adb000)
[26269.172507] e1000e 0000:00:19.0: restoring config space at offset 0x4 (was 0x0, writing 0xf6ae0000)
[26269.172515] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26269.174262] e1000e 0000:00:19.0: PME# disabled
[26269.174339] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26272.384806] e1000e 0000:00:19.0: PME# enabled
[26274.688310] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26275.482490] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26276.277343] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26277.075194] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26277.870807] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26278.667881] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26279.463492] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26280.258982] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26281.056598] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26281.855386] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26282.649838] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26283.445674] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26289.848036] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26289.848044] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26289.848050] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26289.848067] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26289.848090] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26289.848146] e1000e 0000:00:19.0: PME# disabled
[26289.940279] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26289.996092] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26289.996761] ADDRCONF(NETDEV_UP): eth0: link is not ready
[26291.088343] e1000e 0000:00:19.0: PME# enabled
[26900.272077] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26900.272096] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26900.272111] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26900.272142] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26900.272180] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26900.272250] e1000e 0000:00:19.0: PME# disabled
[26900.272379] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26900.274426] e1000e 0000:00:19.0: eth0: MAC Wakeup cause - Link Status Change
[26905.560584] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
[26905.560591] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[26905.560650] e1000e 0000:00:19.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[26905.560665] e1000e 0000:00:19.0: setting latency timer to 64
[26905.560836] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26905.744547] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:21:70:e1:bb:4c
[26905.744552] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[26905.744581] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: 1004FF-0FF
[26905.744594] e1000e 0000:00:19.0: PME# enabled
[26905.880141] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26905.880149] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26905.880155] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26905.880172] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26905.880194] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26905.880247] e1000e 0000:00:19.0: PME# disabled
[26905.968320] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26906.024395] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26906.025907] ADDRCONF(NETDEV_UP): eth0: link is not ready
[26907.112415] e1000e 0000:00:19.0: PME# enabled
[27308.975856] device eth0 entered promiscuous mode
[27326.414382] device eth0 left promiscuous mode
[27336.815362] device eth0 entered promiscuous mode
Quoted 6 lines

* Right after start up: machine is in docking station, network is working fine.
* At 25136: resume machine, not in docking station, no network cable plugged in, so network connection was not tested.
* At 26261: resume machine, in docking station, network cable plugged in, but network connection is not working

but was the light blinking or solid? (link light) or was it just out.

Quoted 1 line

* At 26900: rmmod e1000e && modprobe e1000e: network still not working

it almost sounds like something in the docking station is not quite waking successfully. If the device is in D3, the wake signal was either missed by the system, or never asserted. If you unplug the link and plug it back in, with the driver loaded and it reporting D3 (should go to PME+ and then D0 once cable is plugged in ) does it help?

#3 lore raw
Quoted 130 lines · Jesse Brandeburg
Quoted 121 lines
# dmesg | grep -E "e1000e|eth0"
[    1.027437] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
[    1.027441] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[    1.027480] e1000e 0000:00:19.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    1.027491] e1000e 0000:00:19.0: setting latency timer to 64
[    1.027605] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[    1.231440] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:21:70:e1:bb:4c
[    1.231444] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[    1.231470] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: 1004FF-0FF
[   22.896268] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[   22.952097] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[   22.954132] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   24.504903] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[   24.506413] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[   24.508402] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   34.788022] eth0: no IPv6 routers present
[   41.444922] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx
[   41.446325] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO
[25136.918393] e1000e 0000:00:19.0: PME# enabled
[25142.488050] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[25142.488058] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[25142.488066] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[25142.488085] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[25142.488110] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[25142.488167] e1000e 0000:00:19.0: PME# disabled
[25142.510966] e1000e 0000:00:19.0: PCI INT A disabled
[25142.510971] e1000e 0000:00:19.0: PME# enabled
[25143.468668] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[25143.468689] e1000e 0000:00:19.0: restoring config space at offset 0x6 (was 0x1, writing 0xefe1)
[25143.468696] e1000e 0000:00:19.0: restoring config space at offset 0x5 (was 0x0, writing 0xf6adb000)
[25143.468703] e1000e 0000:00:19.0: restoring config space at offset 0x4 (was 0x0, writing 0xf6ae0000)
[25143.468713] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[25143.471149] e1000e 0000:00:19.0: PME# disabled
[25143.471277] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[25145.276441] e1000e 0000:00:19.0: PME# enabled
[25146.082051] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[25146.082076] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[25146.082090] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[25146.082126] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[25146.082169] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[25146.082280] e1000e 0000:00:19.0: PME# disabled
[25146.176605] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[25146.232228] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[25146.234003] ADDRCONF(NETDEV_UP): eth0: link is not ready
[25147.328875] e1000e 0000:00:19.0: PME# enabled
[26261.896126] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26261.896140] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26261.896149] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26261.896169] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26261.896196] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26261.896241] e1000e 0000:00:19.0: PME# disabled
[26261.896316] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26261.972148] e1000e 0000:00:19.0: PME# enabled
[26268.192160] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26268.192168] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26268.192175] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26268.192194] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26268.192219] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26268.192274] e1000e 0000:00:19.0: PME# disabled
[26268.213875] e1000e 0000:00:19.0: PME# enabled
[26269.172481] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26269.172497] e1000e 0000:00:19.0: restoring config space at offset 0x6 (was 0x1, writing 0xefe1)
[26269.172502] e1000e 0000:00:19.0: restoring config space at offset 0x5 (was 0x0, writing 0xf6adb000)
[26269.172507] e1000e 0000:00:19.0: restoring config space at offset 0x4 (was 0x0, writing 0xf6ae0000)
[26269.172515] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26269.174262] e1000e 0000:00:19.0: PME# disabled
[26269.174339] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26272.384806] e1000e 0000:00:19.0: PME# enabled
[26274.688310] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26275.482490] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26276.277343] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26277.075194] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26277.870807] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26278.667881] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26279.463492] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26280.258982] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26281.056598] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26281.855386] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26282.649838] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26283.445674] e1000e 0000:00:19.0: eth0: Error reading PHY register
[26289.848036] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26289.848044] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26289.848050] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26289.848067] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26289.848090] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26289.848146] e1000e 0000:00:19.0: PME# disabled
[26289.940279] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26289.996092] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26289.996761] ADDRCONF(NETDEV_UP): eth0: link is not ready
[26291.088343] e1000e 0000:00:19.0: PME# enabled
[26900.272077] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26900.272096] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26900.272111] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26900.272142] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26900.272180] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26900.272250] e1000e 0000:00:19.0: PME# disabled
[26900.272379] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26900.274426] e1000e 0000:00:19.0: eth0: MAC Wakeup cause - Link Status Change
[26905.560584] e1000e: Intel(R) PRO/1000 Network Driver - 1.3.10-k2
[26905.560591] e1000e: Copyright(c) 1999 - 2011 Intel Corporation.
[26905.560650] e1000e 0000:00:19.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[26905.560665] e1000e 0000:00:19.0: setting latency timer to 64
[26905.560836] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26905.744547] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:21:70:e1:bb:4c
[26905.744552] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
[26905.744581] e1000e 0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: 1004FF-0FF
[26905.744594] e1000e 0000:00:19.0: PME# enabled
[26905.880141] e1000e 0000:00:19.0: BAR 0: set to [mem 0xf6ae0000-0xf6afffff] (PCI address [0xf6ae0000-0xf6afffff])
[26905.880149] e1000e 0000:00:19.0: BAR 1: set to [mem 0xf6adb000-0xf6adbfff] (PCI address [0xf6adb000-0xf6adbfff])
[26905.880155] e1000e 0000:00:19.0: BAR 2: set to [io  0xefe0-0xefff] (PCI address [0xefe0-0xefff])
[26905.880172] e1000e 0000:00:19.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
[26905.880194] e1000e 0000:00:19.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100107)
[26905.880247] e1000e 0000:00:19.0: PME# disabled
[26905.968320] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26906.024395] e1000e 0000:00:19.0: irq 43 for MSI/MSI-X
[26906.025907] ADDRCONF(NETDEV_UP): eth0: link is not ready
[26907.112415] e1000e 0000:00:19.0: PME# enabled
[27308.975856] device eth0 entered promiscuous mode
[27326.414382] device eth0 left promiscuous mode
[27336.815362] device eth0 entered promiscuous mode
Quoted 6 lines

* Right after start up: machine is in docking station, network is working fine.
* At 25136: resume machine, not in docking station, no network cable plugged in, so network connection was not tested.
* At 26261: resume machine, in docking station, network cable plugged in, but network connection is not working

but was the light blinking or solid? (link light) or was it just out.

Quoted 8 lines
Quoted 1 line

* At 26900: rmmod e1000e && modprobe e1000e: network still not working

it almost sounds like something in the docking station is not quite waking successfully. If the device is in D3, the wake signal was either missed by the system, or never asserted. If you unplug the link and plug it back in, with the driver loaded and it reporting D3 (should go to PME+ and then D0 once cable is plugged in ) does it help?

I don't have the docking station at hand here, but I was able to reproduce the problem without the docking station.

Full syslog (221 KB) is at
http://artipc10.vub.ac.be/~frederik/e1000e/syslog

This is what happened:
* 21:33:11: cold boot, network cable plugged in, network working fine
* 21:35:24: start suspend to ram
* 21:35:40: resume system, e1000e network working fine (however, wlan now refuses to connect, but I have not investigated that, not sure if whether this might be related or not)
* 21:52:44: logs are filled up with an endless loop of these messages (I think I disconnected the network cable at that time:

Sep  9 21:52:44 defected kernel: [ 1188.440061] ehci_hcd 0000:00:1d.7: BAR 0: set to [mem 0xfed1c000-0xfed1c3ff] (PCI address [0xfed1c000-0xfed1c3ff])
Sep  9 21:52:44 defected kernel: [ 1188.440097] ehci_hcd 0000:00:1d.7: restoring config space at offset 0xf (was 0x100, writing 0x104)
Sep  9 21:52:44 defected kernel: [ 1188.440137] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102)
Sep  9 21:52:44 defected kernel: [ 1188.447422] ehci_hcd 0000:00:1d.7: PME# disabled
Sep  9 21:52:44 defected kernel: [ 1188.447446] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
Sep  9 21:52:44 defected kernel: [ 1188.447461] ehci_hcd 0000:00:1d.7: setting latency timer to 64
Sep  9 21:52:44 defected kernel: [ 1188.447519] ehci_hcd 0000:00:1d.7: PCI INT A disabled
Sep  9 21:52:44 defected kernel: [ 1188.447588] ehci_hcd 0000:00:1d.7: PME# enabled
Sep  9 21:52:44 defected kernel: [ 1188.468704] ehci_hcd 0000:00:1a.7: BAR 0: set to [mem 0xfed1c400-0xfed1c7ff] (PCI address [0xfed1c400-0xfed1c7ff])
Sep  9 21:52:44 defected kernel: [ 1188.468739] ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x300, writing 0x30a)
Sep  9 21:52:44 defected kernel: [ 1188.468778] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102)
Sep  9 21:52:44 defected kernel: [ 1188.476179] ehci_hcd 0000:00:1a.7: PME# disabled
Sep  9 21:52:44 defected kernel: [ 1188.476201] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
Sep  9 21:52:44 defected kernel: [ 1188.476215] ehci_hcd 0000:00:1a.7: setting latency timer to 64
Sep  9 21:52:44 defected kernel: [ 1188.476264] ehci_hcd 0000:00:1a.7: PCI INT C disabled
Sep  9 21:52:44 defected kernel: [ 1188.476325] ehci_hcd 0000:00:1a.7: PME# enabled
Sep  9 21:52:44 defected kernel: [ 1188.500063] ehci_hcd 0000:00:1d.7: BAR 0: set to [mem 0xfed1c000-0xfed1c3ff] (PCI address [0xfed1c000-0xfed1c3ff])
Sep  9 21:52:44 defected kernel: [ 1188.500097] ehci_hcd 0000:00:1d.7: restoring config space at offset 0xf (was 0x100, writing 0x104)
Sep  9 21:52:44 defected kernel: [ 1188.500136] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102)
Sep  9 21:52:44 defected kernel: [ 1188.507398] ehci_hcd 0000:00:1d.7: PME# disabled
Sep  9 21:52:44 defected kernel: [ 1188.507418] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
Sep  9 21:52:44 defected kernel: [ 1188.507431] ehci_hcd 0000:00:1d.7: setting latency timer to 64
Sep  9 21:52:44 defected kernel: [ 1188.507499] ehci_hcd 0000:00:1d.7: PCI INT A disabled
Sep  9 21:52:44 defected kernel: [ 1188.507560] ehci_hcd 0000:00:1d.7: PME# enabled
Sep  9 21:52:44 defected kernel: [ 1188.528053] ehci_hcd 0000:00:1a.7: BAR 0: set to [mem 0xfed1c400-0xfed1c7ff] (PCI address [0xfed1c400-0xfed1c7ff])
Sep  9 21:52:44 defected kernel: [ 1188.528085] ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x300, writing 0x30a)
Sep  9 21:52:44 defected kernel: [ 1188.528124] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102)
Sep  9 21:52:44 defected kernel: [ 1188.535363] ehci_hcd 0000:00:1a.7: PME# disabled
Sep  9 21:52:44 defected kernel: [ 1188.535382] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
Sep  9 21:52:44 defected kernel: [ 1188.535396] ehci_hcd 0000:00:1a.7: setting latency timer to 64
Sep  9 21:52:44 defected kernel: [ 1188.535455] ehci_hcd 0000:00:1a.7: PCI INT C disabled
Sep  9 21:52:44 defected kernel: [ 1188.535517] ehci_hcd 0000:00:1a.7: PME# enabled
Sep  9 21:52:44 defected kernel: [ 1188.560164] ehci_hcd 0000:00:1d.7: BAR 0: set to [mem 0xfed1c000-0xfed1c3ff] (PCI address [0xfed1c000-0xfed1c3ff])
Sep  9 21:52:44 defected kernel: [ 1188.560198] ehci_hcd 0000:00:1d.7: restoring config space at offset 0xf (was 0x100, writing 0x104)
Sep  9 21:52:44 defected kernel: [ 1188.560237] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102)
Sep  9 21:52:44 defected kernel: [ 1188.568578] ehci_hcd 0000:00:1d.7: PME# disabled
Sep  9 21:52:44 defected kernel: [ 1188.568600] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
Sep  9 21:52:44 defected kernel: [ 1188.568614] ehci_hcd 0000:00:1d.7: setting latency timer to 64
Sep  9 21:52:44 defected kernel: [ 1188.568663] ehci_hcd 0000:00:1d.7: PCI INT A disabled
Sep  9 21:52:44 defected kernel: [ 1188.568724] ehci_hcd 0000:00:1d.7: PME# enabled

Are there any other tests I can do to help finding out what's wrong?

Signature · 1 line
Frederik Himpe <[email protected]>
#4 lore raw
In reply to Jesse Brandeburg
Quoted 12 lines · Frederik Himpe

Full syslog (221 KB) is at
http://artipc10.vub.ac.be/~frederik/e1000e/syslog

This is what happened:
* 21:33:11: cold boot, network cable plugged in, network working fine
* 21:35:24: start suspend to ram
* 21:35:40: resume system, e1000e network working fine (however, wlan now refuses to connect, but I have not investigated that, not sure if whether this might be related or not)
* 21:52:44: logs are filled up with an endless loop of these messages (I think I disconnected the network cable at that time:

Quoted 8 lines
Sep  9 21:52:44 defected kernel: [ 1188.440061] ehci_hcd 0000:00:1d.7: BAR 0: set to [mem 0xfed1c000-0xfed1c3ff] (PCI address [0xfed1c000-0xfed1c3ff])
Sep  9 21:52:44 defected kernel: [ 1188.440097] ehci_hcd 0000:00:1d.7: restoring config space at offset 0xf (was 0x100, writing 0x104)
Sep  9 21:52:44 defected kernel: [ 1188.440137] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102)
Sep  9 21:52:44 defected kernel: [ 1188.447422] ehci_hcd 0000:00:1d.7: PME# disabled
Sep  9 21:52:44 defected kernel: [ 1188.447446] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
Sep  9 21:52:44 defected kernel: [ 1188.447461] ehci_hcd 0000:00:1d.7: setting latency timer to 64
Sep  9 21:52:44 defected kernel: [ 1188.447519] ehci_hcd 0000:00:1d.7: PCI INT A disabled
Sep  9 21:52:44 defected kernel: [ 1188.447588] ehci_hcd 0000:00:1d.7: PME# enabled

Reproduced this again, and the above loop happens when reconnecting the network cable.

So when network is working fine and I disconnetc the cable, this appears in the logs:

Sep  9 23:35:55 defected kernel: [ 5931.492189] e1000e: eth0 NIC Link is Down
Sep  9 23:35:55 defected kernel: [ 5931.662818] e1000e 0000:00:19.0: PCI INT A disabled
Sep  9 23:35:55 defected kernel: [ 5931.662836] e1000e 0000:00:19.0: PME# enabled
Sep  9 23:35:55 defected kernel: [ 5931.676060] ehci_hcd 0000:00:1d.7: BAR 0: set to [mem 0xfed1c000-0xfed1c3ff] (PCI address [0xfed1c000-0xfed1c3ff])
Sep  9 23:35:55 defected kernel: [ 5931.676093] ehci_hcd 0000:00:1d.7: restoring config space at offset 0xf (was 0x100, writing 0x104)
Sep  9 23:35:55 defected kernel: [ 5931.676132] ehci_hcd 0000:00:1d.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102)
Sep  9 23:35:55 defected kernel: [ 5931.683253] ehci_hcd 0000:00:1d.7: PME# disabled
Sep  9 23:35:55 defected kernel: [ 5931.683276] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20
Sep  9 23:35:55 defected kernel: [ 5931.683290] ehci_hcd 0000:00:1d.7: setting latency timer to 64
Sep  9 23:35:55 defected kernel: [ 5931.683350] ehci_hcd 0000:00:1d.7: PCI INT A disabled
Sep  9 23:35:55 defected kernel: [ 5931.683412] ehci_hcd 0000:00:1d.7: PME# enabled
Sep  9 23:35:55 defected kernel: [ 5931.704067] ehci_hcd 0000:00:1a.7: BAR 0: set to [mem 0xfed1c400-0xfed1c7ff] (PCI address [0xfed1c400-0xfed1c7ff])
Sep  9 23:35:55 defected kernel: [ 5931.704099] ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x300, writing 0x30a)
Sep  9 23:35:55 defected kernel: [ 5931.704137] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900102)
Sep  9 23:35:55 defected kernel: [ 5931.711840] ehci_hcd 0000:00:1a.7: PME# disabled
Sep  9 23:35:55 defected kernel: [ 5931.711863] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 22 (level, low) -> IRQ 22
Sep  9 23:35:55 defected kernel: [ 5931.711877] ehci_hcd 0000:00:1a.7: setting latency timer to 64
Sep  9 23:35:55 defected kernel: [ 5931.711948] ehci_hcd 0000:00:1a.7: PCI INT C disabled
Sep  9 23:35:55 defected kernel: [ 5931.712045] ehci_hcd 0000:00:1a.7: PME# enabled

When I reconnect the cable again one minute later, there is no information anymore about e1000e in the kernel logs and ehci_hcd ends up in the endless loop.

Signature · 1 line
Frederik Himpe <[email protected]>