Skip to contentSkip to conversation

system freeze with kernel 3.2-rc7

DISCUSSION Kai Krakow 6 participants 16 messages Dec 26, 2011 – Jan 13, 2012

lore
Share & tools
lore

Kai Krakow

author
#0 lore raw

Hello!

I found my system freeze mostly during starting up X and KDE. Sometimes it works for some minutes, sometimes it freezes immediatly. When the freeze happens, everything is dead (even the reset button does not work, I need to power cycle).

I was using libdrm-2.4.27 before, system freeze showed some colorful lines running down at the left side of the screen after turning black, then some blue flicker in the top 10% of the the screen. System no longer reacts, network is dead too.

Now, using libdrm-2.4.29, the system freeze shows other effects: Screen does not turn black but starts to flicker and occassionally moves some centimeters to the right (wrapping the right-most part to the left) for a very short time, then jumping back with some distortions. The rest is the
same: Complete freeze, even reset button stops working.

Before finding out about the libdrm difference, I tried other intel xorg driver versions to no avail, I tried with SNA support and without. No difference. I'm now back to intel xorg driver 2.17.0.

I read about the semaphores feature, turned it off: No change. Sometimes the system even freezes before displaying the framebuffer splash.

I didn't have such issues with early 3.2 rcs (afair), and not with 3.1 kernels. After some digging through google I've found you enabled RC6 in 3.2. I disabled it now, and my system runs wonderfully.

Do you need any specs? I'd be happy to send these. The system is a Z68 Pro board with Sandybridge i5-2500K processor, 8 GB of RAM and UEFI firmware. Looks like RC6 is not ready for roll-out, at least on some mainboards.

Regards,
Kai

#1 lore raw
Quoted 3 lines · Kai Krakow

I didn't have such issues with early 3.2 rcs (afair), and not with 3.1 kernels. After some digging through google I've found you enabled RC6 in 3.2. I disabled it now, and my system runs wonderfully.

Argh. Can you try building a kernel with VT-d support? I assume you can't turn VT-d off in the BIOS as it's UEFI?

Signature · 1 line
[email protected]

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

author
#2 lore raw
Quoted 9 lines · Keith Packard
Quoted 3 lines · Kai Krakow

I didn't have such issues with early 3.2 rcs (afair), and not with 3.1 kernels. After some digging through google I've found you enabled RC6 in 3.2. I disabled it now, and my system runs wonderfully.

Argh. Can you try building a kernel with VT-d support? I assume you can't turn VT-d off in the BIOS as it's UEFI?

kakra@jupiter ~ $ zgrep -i iommu /proc/config.gz
CONFIG_GART_IOMMU=y
# CONFIG_CALGARY_IOMMU is not set
CONFIG_IOMMU_HELPER=y
CONFIG_IOMMU_API=y
CONFIG_IOMMU_SUPPORT=y
# CONFIG_AMD_IOMMU is not set
CONFIG_INTEL_IOMMU=y
CONFIG_INTEL_IOMMU_DEFAULT_ON=y
CONFIG_INTEL_IOMMU_FLOPPY_WA=y
# CONFIG_IOMMU_DEBUG is not set
# CONFIG_IOMMU_STRESS is not set

So kernel vt-d support is on. Not sure what to look for in dmesg thou... I didn't look into the BIOS settings yet, but usually if there is such an option I turn it on because I use virtual machines.

Regards,
Kai

#3 lore raw
Quoted 25 lines · Kai Krakow
Quoted 9 lines · Keith Packard
Quoted 3 lines · Kai Krakow

I didn't have such issues with early 3.2 rcs (afair), and not with 3.1 kernels. After some digging through google I've found you enabled RC6 in 3.2. I disabled it now, and my system runs wonderfully.

Argh. Can you try building a kernel with VT-d support? I assume you can't turn VT-d off in the BIOS as it's UEFI?

kakra@jupiter ~ $ zgrep -i iommu /proc/config.gz
CONFIG_GART_IOMMU=y
# CONFIG_CALGARY_IOMMU is not set
CONFIG_IOMMU_HELPER=y
CONFIG_IOMMU_API=y
CONFIG_IOMMU_SUPPORT=y
# CONFIG_AMD_IOMMU is not set
CONFIG_INTEL_IOMMU=y
CONFIG_INTEL_IOMMU_DEFAULT_ON=y
CONFIG_INTEL_IOMMU_FLOPPY_WA=y
# CONFIG_IOMMU_DEBUG is not set
# CONFIG_IOMMU_STRESS is not set

Quoted 3 lines

So kernel vt-d support is on. Not sure what to look for in dmesg thou... I didn't look into the BIOS settings yet, but usually if there is such an option I turn it on because I use virtual machines.

You almost certainly don't need IOMMU/VT-d support though; that virtualizes devices for DMA by the guest OS, which generally no-one does.

The BIOS manual for the Z68 board mentions two configuration options,

CPU Configuration:

Intel Virtualization Technology
When this option is set to [Enabled], a VMM (Virtual Machine Architecture) can utilize the additional hardware capabilities provided by Vanderpool Technology. This option will be hidden if the installed CPU does not support Intel Virtualization Technology.

North Bridge Configuration:

VT-d
Use this to enable or disable Intel® VT-d technology (Intel® Virtualization Technology for Directed I/O). The default value of this feature is [Disabled].

I'd love to see tests with these in the three possible combinations:

VT enabled, VT-d enabled
VT enabled, VT-d disabled
VT disabled, VT-d disabled

Meanwhile, I'll get a patch ready for 3.2 which disables RC6 again.

Signature · 1 line
[email protected]

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

author
#4 lore raw
Quoted 8 lines · Keith Packard

You almost certainly don't need IOMMU/VT-d support though; that virtualizes devices for DMA by the guest OS, which generally no-one does.

The BIOS manual for the Z68 board mentions two configuration options,

CPU Configuration:
Intel Virtualization Technology

This exists...

Quoted 2 lines

North Bridge Configuration:
VT-d

This doesn't...

Quoted 5 lines

I'd love to see tests with these in the three possible combinations:

VT enabled, VT-d enabled
VT enabled, VT-d disabled
VT disabled, VT-d disabled

Since there's only VT in my BIOS, I tested both settings, and both failed. I can only reliably boot with RC6 disabled. Otherwise it reproducably hangs on a black screen either just before the boot splash or it never shows the boot splash from initramfs (but works, I see HD activity) and then hangs on loading the next boot splash from real_root. The monitor goes into idle when this happens. But usually the system gets past this and later fails to start or log in to X. The screen goes crazy (flickering or colorful stripes running down the left side of the screen) when this happens. System freezes completely, e.g. if I had HD activity the LED stays on forever, hw reset button dead.

Quoted 1 line

Meanwhile, I'll get a patch ready for 3.2 which disables RC6 again.

If I should provide more info to identify my system, please tell me.

Regards,
Kai

#5 lore raw
Quoted 4 lines · Kai Krakow
Quoted 2 lines

North Bridge Configuration:
VT-d

This doesn't exist

That's odd. I don't understand all of the SNB CPU variations; perhaps there's a desktop version that has VT-d fused out or something?

Quoted 1 line

If I should provide more info to identify my system, please tell me.

# lspci -nn -vv
Signature · 1 line
[email protected]

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

author
#6 lore raw
Quoted 6 lines · Keith Packard
Quoted 3 lines · Kai Krakow
Quoted 2 lines

North Bridge Configuration:
VT-d

Quoted 8 lines
Quoted 1 line

This doesn't exist

That's odd. I don't understand all of the SNB CPU variations; perhaps there's a desktop version that has VT-d fused out or something?

Quoted 1 line

If I should provide more info to identify my system, please tell me.

# lspci -nn -vv

00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0100] (rev 09)
Subsystem: ASRock Incorporation Device [1849:0100]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?> Kernel driver in use: agpgart-intel

00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0112] (rev 09) (prog-if 00 [VGA controller])
Subsystem: ASRock Incorporation Device [1849:0112]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin A routed to IRQ 44
        Region 0: Memory at fe000000 (64-bit, non-prefetchable) [size=4M]
        Region 2: Memory at c0000000 (64-bit, prefetchable) [size=256M]
        Region 4: I/O ports at f000 [size=64]
        Expansion ROM at <unassigned> [disabled]
        Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
                Address: fee0100c  Data: 4179
        Capabilities: [d0] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA 

PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a4] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: i915

00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
Subsystem: ASRock Incorporation Device [1849:1c3a]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fe608000 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000

00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI])
Subsystem: ASRock Incorporation Device [1849:1c2d]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fe607000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd

00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05)
Subsystem: ASRock Incorporation Device [1849:1892]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 48
Region 0: Memory at fe600000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0400c Data: 41a9
Capabilities: [70] Express (v1) Root Complex Integrated Endpoint,
MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE- FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown,
Latency L0 <64ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk-
DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=00
Status: NegoPending- InProgress-
Capabilities: [130 v1] Root Complex Link
Desc: PortNumber=0f ComponentID=00 EltType=Config
Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB-
LinkType=MemMapped LinkValid+
Addr: 00000000fed1c000
Kernel driver in use: snd_hda_intel

00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #1, Speed 5GT/s, Width x1, ASPM L0s L1, Latency
L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #0, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4159
Capabilities: [90] Subsystem: ASRock Incorporation Device
[1849:1c10]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport

00:1c.4 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev b5) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0 I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fe500000-fe5fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #5, Speed 5GT/s, Width x1, ASPM L0s L1, Latency
L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #4, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Address: 00000000 Data: 0000
Capabilities: [90] Subsystem: ASRock Incorporation Device
[1849:244e]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-

00:1c.5 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 [8086:1c1a] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
        I/O behind bridge: 0000d000-0000dfff
        Prefetchable memory behind bridge: 00000000d0000000-00000000d00fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 

<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #6, Speed 5GT/s, Width x1, ASPM L0s L1, Latency
L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #5, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4161
Capabilities: [90] Subsystem: ASRock Incorporation Device
[1849:1c1a]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport

00:1c.6 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 [8086:1c1c] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 Memory behind bridge: fe400000-fe4fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #7, Speed 5GT/s, Width x1, ASPM L0s L1, Latency
L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #6, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet- LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4169
Capabilities: [90] Subsystem: ASRock Incorporation Device
[1849:1c1c]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport

00:1c.7 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 [8086:1c1e] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+
TransPend-
LnkCap: Port #8, Speed 5GT/s, Width x1, ASPM L0s L1, Latency
L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surprise-
Slot #7, PowerLimit 10.000W; Interlock- NoCompl+
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt-
HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power-
Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet-
Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna+
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range BC, TimeoutDis+ ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
ARIFwd-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Address: fee0f00c Data: 4171
Capabilities: [90] Subsystem: ASRock Incorporation Device
[1849:1c1e]
Capabilities: [a0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pcieport

00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
Subsystem: ASRock Incorporation Device [1849:1c26]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fe606000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ehci_hcd

00:1f.0 ISA bridge [0601]: Intel Corporation Z68 Express Chipset Family LPC Controller [8086:1c44] (rev 05)
Subsystem: ASRock Incorporation Device [1849:1c44]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c02] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: ASRock Incorporation Device [1849:1c02]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 0
        Interrupt: pin B routed to IRQ 45
        Region 0: I/O ports at f0b0 [size=8]
        Region 1: I/O ports at f0a0 [size=4]
        Region 2: I/O ports at f090 [size=8]
        Region 3: I/O ports at f080 [size=4]
        Region 4: I/O ports at f060 [size=32]
        Region 5: Memory at fe605000 (32-bit, non-prefetchable) [size=2K]
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
                Address: fee0100c  Data: 4181
        Capabilities: [70] Power Management version 3
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 

PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a8] SATA HBA v1.0 BAR4 Offset=00000004
Capabilities: [b0] PCI Advanced Features
AFCap: TP+ FLR+
AFCtrl: FLR-
AFStatus: TP-
Kernel driver in use: ahci

00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
Subsystem: ASRock Incorporation Device [1849:1c22]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at fe604000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at f040 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c-i801

02:00.0 PCI bridge [0604]: ASMedia Technology Inc. ASM108x PCIe to PCI Bridge Controller [1b21:1080] (rev 03) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=03, sec-latency=32 I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fe500000-fe5fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [c0] Subsystem: ASRock Incorporation Device
[1849:1080]

03:01.0 RAID bus controller [0104]: Silicon Image, Inc. SiI 0649 Ultra ATA/100 PCI to ATA Host Controller [1095:0649] (rev 02)
Subsystem: Silicon Image, Inc. SiI 0649 Ultra ATA/100 PCI to ATA
Host Controller [1095:0649]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-

        Latency: 64 (500ns min, 1000ns max)
        Interrupt: pin A routed to IRQ 17
        Region 0: I/O ports at e040 [size=8]
        Region 1: I/O ports at e030 [size=4]
        Region 2: I/O ports at e020 [size=8]
        Region 3: I/O ports at e010 [size=4]
        Region 4: I/O ports at e000 [size=16]
        Expansion ROM at fe500000 [disabled] [size=512K]
        Capabilities: [60] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA 

PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=3 PME-
Kernel driver in use: pata_cmd64x
Kernel modules: pata_cmd64x

04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06)
Subsystem: ASRock Incorporation Motherboard (one of many)
[1849:8168]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 46
Region 0: I/O ports at d000 [size=256]
Region 2: Memory at d0004000 (64-bit, prefetchable) [size=4K] Region 4: Memory at d0000000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee0100c Data: 4189
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s
<512ns, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 4096 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+
TransPend-

                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, 

Latency L0 unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
No end tag found
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO+ CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 0e, GenCap+ CGenEn- ChkCap+
ChkEn-
Capabilities: [140 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128-
WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 01-00-00-00-68-4c-e0-00 Kernel driver in use: r8169

05:00.0 USB controller [0c03]: Etron Technology, Inc. EJ168 USB 3.0 Host Controller [1b6f:7023] (rev 01) (prog-if 30 [XHCI])
Subsystem: ASRock Incorporation Device [1849:7023]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 47
Region 0: Memory at fe400000 (64-bit, non-prefetchable) [size=32K]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] MSI: Enable+ Count=1/4 Maskable+ 64bit+
Address: 00000000fee0800c Data: 4199
Masking: 0000000e Pending: 00000000
Capabilities: [a0] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s
<64ns, L1 <1us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
FLReset-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x1, ASPM L0s L1, Latency
L0 <1us, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x1, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance-
SpeedDis-, Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range,
EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt-
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt-
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout+
NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout-
NonFatalErr+
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+
ChkEn-
Capabilities: [190 v1] Device Serial Number 01-01-01-01-01-01-01-01 Kernel driver in use: xhci_hcd

#7 lore raw
Quoted 2 lines · Kai Krakow

00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor
...

Thanks. I'll see about duplicating this system here so we can try and make it work and still have RC6 enabled, either by fixing it for this platform or figuring out a likely combination of values that disable for this machine while leaving it enabled for most others.

Signature · 1 line
[email protected]

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#8 lore raw
In reply to Keith Packard
Quoted 9 lines · Keith Packard
Quoted 4 lines · Kai Krakow
Quoted 2 lines

North Bridge Configuration:
VT-d

This doesn't exist

That's odd. I don't understand all of the SNB CPU variations; perhaps there's a desktop version that has VT-d fused out or something?

The K variants of SandyBridge CPUs don't have VT-d. Here is the product page for the 2500K:

http://ark.intel.com/products/52210/

Regards,
Tino

#9 lore raw
In reply to Keith Packard
Quoted 9 lines · Keith Packard
Quoted 4 lines · Kai Krakow
Quoted 2 lines

North Bridge Configuration:
VT-d

This doesn't exist

That's odd. I don't understand all of the SNB CPU variations; perhaps there's a desktop version that has VT-d fused out or something?

The K variants of SandyBridge CPUs don't have VT-d. Here is the product page for the 2500K:

http://ark.intel.com/products/52210/

Regards,
Tino

#10 lore raw

I'm not sure if mentioning this helps, but I think I'm experiencing the same problem.

My system will occasionally freeze completely (numlock and SysRq key don't work) with the image on the screen completely frozen (I don't get any artifacts). I then use the power button to reboot.

I use Arch Linux. libdrm 2.4.27 works. 2.4.28 - 2.4.29 freezes. Freezes occur with catalyst-11.11 and 11.12 and with xorg-server-1.10 and 1.11 and with linux-3.1.5 and 3.1.4.

$ uname -a
Linux J 3.1.5-1-ARCH #1 SMP PREEMPT Sat Dec 10 14:43:09 CET 2011 x86_64 Intel(R) 
Core(TM) i7 CPU Q 720 @ 1.60GHz GenuineIntel GNU/Linux

ATI Mobility Radeon HD 5850 with catalyst driver (I need GPU opencl atm)

laptop model:
http://www.newegg.com/Product/Product.aspx?Item=N82E16834157515

#11 lore raw
Quoted 4 lines · Kevin <kjslag <at> gmail.com> writes:

I'm not sure if mentioning this helps, but I think I'm experiencing the same problem.
...

Nevermind, I got libdrm-2.4.27 to freeze. Everything (including capslock and sysrq) was frozen except my mouse, which would move just fine.

It's possible I'm affected by this bug
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/908335
I use brcmsmac

#12 lore raw
Quoted 8 lines · Kevin
Quoted 2 lines · Kevin <kjslag <at> gmail.com> writes:

I'm not sure if mentioning this helps, but I think I'm experiencing the

same

Quoted 2 lines

problem.
...

Quoted 8 lines

Nevermind, I got libdrm-2.4.27 to freeze. Everything (including capslock and
sysrq) was frozen except my mouse, which would move just fine.

It's possible I'm affected by this bug
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/908335
I use brcmsmac

Is there a way to setup a netconsole for your machine and check what happens during the hangs? The last dying words of the machine could be very helpful.

Thanks!

Signature · 2 lines
Eugeni Dodonov
<http://eugeni.dodonov.net/>

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#13 lore raw
In reply to Kai Krakow
Quoted 29 lines · Kai Krakow

Hello!

I found my system freeze mostly during starting up X and KDE. Sometimes it works for some minutes, sometimes it freezes immediatly. When the freeze happens, everything is dead (even the reset button does not work, I need to power cycle).

I was using libdrm-2.4.27 before, system freeze showed some colorful lines running down at the left side of the screen after turning black, then some blue flicker in the top 10% of the the screen. System no longer reacts, network is dead too.

Now, using libdrm-2.4.29, the system freeze shows other effects: Screen does not turn black but starts to flicker and occassionally moves some centimeters to the right (wrapping the right-most part to the left) for a very short time, then jumping back with some distortions. The rest is the
same: Complete freeze, even reset button stops working.

Before finding out about the libdrm difference, I tried other intel xorg driver versions to no avail, I tried with SNA support and without. No difference. I'm now back to intel xorg driver 2.17.0.

I read about the semaphores feature, turned it off: No change. Sometimes the system even freezes before displaying the framebuffer splash.

I didn't have such issues with early 3.2 rcs (afair), and not with 3.1 kernels. After some digging through google I've found you enabled RC6 in 3.2. I disabled it now, and my system runs wonderfully.

Quoted 6 lines

Do you need any specs? I'd be happy to send these. The system is a Z68 Pro board with Sandybridge i5-2500K processor, 8 GB of RAM and UEFI firmware. Looks like RC6 is not ready for roll-out, at least on some mainboards.

Regards,
Kai

Can you please try this kernel:
git://people.freedesktop.org/~bwidawsk/drm-intel context-support

You probably need to manually enable rc6. We were given some hint that we may not be setting up contexts properly. The above branch should create a default context (amongst other stuff which won't happen in this case).

Thanks.
Ben

author
#14 lore raw
Quoted 5 lines · Ben Widawsky
Quoted 4 lines · Kai Krakow

I found my system freeze mostly during starting up X and KDE. Sometimes it works for some minutes, sometimes it freezes immediatly. When the freeze happens, everything is dead (even the reset button does not work, I need to power cycle).

[...]

Quoted 7 lines

Can you please try this kernel:
git://people.freedesktop.org/~bwidawsk/drm-intel context-support

You probably need to manually enable rc6. We were given some hint that we may not be setting up contexts properly. The above branch should create a default context (amongst other stuff which won't happen in this case).

Since that branch seems to be based off 3.2-rc6 I didn't need to enable RC6, it was on by default.

But I'm sorry to inform you that this still makes my system board freeze during KDE login, sometimes early, sometimes late during loading of the desktop.

My system freezes completely: Keyboard dead, SysRq shortcuts dead, screen goes blank (or shows funny lightshows before blanking), even the hard disk LED freezes. I need to power cycle to get back into a working state. If I only use the reset switch, the board behaves strange after reboot. The reset button sometimes takes a few seconds to make the system reboot when frozen.

All this tells me that something really bad goes on within the CPU/GPU/chipset during freeze which even survives a board reset. Only power cycling helps.

Keith got the specs of my system and wanted to "mirror" it for development. Maybe he could find out better what happens. I have no idea how to debug that because everything freezes so badly.

Regards,
Kai

#15 lore raw
Quoted 16 lines · Kai Krakow
Quoted 5 lines · Ben Widawsky
Quoted 4 lines · Kai Krakow

I found my system freeze mostly during starting up X and KDE. Sometimes it works for some minutes, sometimes it freezes immediatly. When the freeze happens, everything is dead (even the reset button does not work, I need to power cycle).

[...]

Quoted 7 lines

Can you please try this kernel:
git://people.freedesktop.org/~bwidawsk/drm-intel context-support

You probably need to manually enable rc6. We were given some hint that we may not be setting up contexts properly. The above branch should create a default context (amongst other stuff which won't happen in this case).

Quoted 6 lines

Since that branch seems to be based off 3.2-rc6 I didn't need to enable RC6, it was on by default.

But I'm sorry to inform you that this still makes my system board freeze during KDE login, sometimes early, sometimes late during loading of the desktop.

Thanks. At least we can give this information back to our design team.

Quoted 11 lines

My system freezes completely: Keyboard dead, SysRq shortcuts dead, screen goes blank (or shows funny lightshows before blanking), even the hard disk LED freezes. I need to power cycle to get back into a working state. If I only use the reset switch, the board behaves strange after reboot. The reset button sometimes takes a few seconds to make the system reboot when frozen.

All this tells me that something really bad goes on within the CPU/GPU/chipset during freeze which even survives a board reset. Only power cycling helps.

Quoted 6 lines

Keith got the specs of my system and wanted to "mirror" it for development. Maybe he could find out better what happens. I have no idea how to debug that because everything freezes so badly.

Regards,
Kai

Jesse, would you care to update VPG with this info?

Ben