Skip to contentSkip to conversation

u-boot boot process is broken, how do i recover?

U-Boot JPT 3 participants 10 messages Apr 3, 2013 – Apr 7, 2013

lore
Share & tools
lore

JPT

author
#0 lore raw

Hi,

I've got a readynas and successfully installed a recent kernel into ROM and Debian onto hard-drive.
But when I tried to modify the uboot-env from uboot-console I had trouble with the ; in the vars. And did not know how to escape. So I tried to access uboot-env from linux.

I applied something like this (well, not that straight forward)

/etc/fw_env.config

# device    offset   size      Flash sector size   Number of sectors
/dev/mtd1   0x0      0x20000   0x20000             1

Maybe there is something wrong in my config?

apt-get install uboot-envtools
fw_printenv bootcmd
fw_setenv bootcmd.bak 'nand read.e 0x1200000 0x200000 0x600000;nand read.e 0x2000000 0x800000 0x1000000;bootm 0x1200000 0x2000000'

fw_setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'

fw_printenv bootcmd.bak bootcmd
fw_printenv bootargs
fw_setenv bootargs.bak 'console=ttyS0,115200 reason=normal
mtdparts=nand_mtd:0x180000 at 0(u-boot),0x20000 at 0x180000(u-boot-env),0x600000 at 0x200000(uImage),0x1000000 at 0x800000(minirootfs),0x6800000 at 0x1800000(jffs2)'

fw_setenv bootargs 'console=ttyS0,115200 root=/dev/sda3
mtdparts=nand_mtd:0x180000 at 0(u-boot),0x20000 at 0x180000(u-boot-env),0x600000 at 0x200000(uImage),0x1000000 at 0x800000(minirootfs),0x6800000 at 0x1800000(jffs2)'

fw_printenv bootargs.bak bootargs

btw, kernel said:
Creating 5 MTD partitions on "nand_mtd":
0x000000000000-0x000000180000 : "u-boot"
0x000000180000-0x0000001a0000 : "u-boot-env"
0x000000200000-0x000000800000 : "uImage"
0x000000800000-0x000001800000 : "minirootfs"
0x000001800000-0x000008000000 : "jffs2"

Now the boot process is broken. I don't understand why.
It stops right after the network (see below). Usually the boot countdown should appear afterwards.
Is there anything I can do except unsoldering the ROM?

If I have to remove the chip and burn it using an external writer... Is there any way to buy similar chip which can be mounted on a socket?

It's a H27U1G8F2BTR-BC (newer version of HY27UF081G2B-TCB) which is NAND flash, 2,7-3,6V, 1Gbitx8 (128 MiB), SLC Single Die + Large Block, TSOP 48 pin. There is also a FBGA 63 PIN available. are there any sockets for FBGA I can solder to TSOP?
Or do other manufacturers offer compatible chips which can be applied to a socket?

thanks for any help!

Jan

          __  __                      _ _
         |  \/  | __ _ _ ____   _____| | |
         | |\/| |/ _` | '__\ \ / / _ \ | |
         | |  | | (_| | |   \ V /  __/ | |
         |_|  |_|\__,_|_|    \_/ \___|_|_|
  _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_

\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Feb 6 2012 - 14:40:46) Marvell version: 3.4.27 Netgear version: Uboot-1_1_4-NetgearDUOV3-V1008

U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006D0120

Soc: MV88F1155 Rev 1 (DDR3)
CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM unknown CAL tRP = 8 tRAS = 20 tRCD=8
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:128 MB
Flash: 0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

USB 0: host mode
PEX 0: PCI Express Root Complex Interface
PEX interface detected Link X1
Switch On !

Net: egiga0 [PRIME]

#1 lore raw

Hi JPT,

Quoted 8 lines · JPT

Hi,

I've got a readynas and successfully installed a recent kernel into ROM and Debian onto hard-drive.
But when I tried to modify the uboot-env from uboot-console I had trouble with the ; in the vars. And did not know how to escape. So I tried to access uboot-env from linux.

Quoted 7 lines

I applied something like this (well, not that straight forward)

/etc/fw_env.config

# device    offset   size      Flash sector size   Number of sectors
/dev/mtd1   0x0      0x20000   0x20000             1

Maybe there is something wrong in my config?

Not in /etc/fw_env.config as far as I can tell, but maybe your Netgear-made u-boot is special.

Quoted 2 lines

apt-get install uboot-envtools
fw_printenv bootcmd

No result there? There should be.

Quoted 24 lines

fw_setenv bootcmd.bak 'nand read.e 0x1200000 0x200000 0x600000;nand read.e 0x2000000 0x800000 0x1000000;bootm 0x1200000 0x2000000'

fw_setenv bootcmd 'nand read.e 0x1200000 0x200000 0x600000;bootm 0x1200000'

fw_printenv bootcmd.bak bootcmd
fw_printenv bootargs
fw_setenv bootargs.bak 'console=ttyS0,115200 reason=normal
mtdparts=nand_mtd:0x180000 at 0(u-boot),0x20000 at 0x180000(u-boot-env),0x600000 at 0x200000(uImage),0x1000000 at 0x800000(minirootfs),0x6800000 at 0x1800000(jffs2)'

fw_setenv bootargs 'console=ttyS0,115200 root=/dev/sda3
mtdparts=nand_mtd:0x180000 at 0(u-boot),0x20000 at 0x180000(u-boot-env),0x600000 at 0x200000(uImage),0x1000000 at 0x800000(minirootfs),0x6800000 at 0x1800000(jffs2)'

fw_printenv bootargs.bak bootargs

btw, kernel said:
Creating 5 MTD partitions on "nand_mtd":
0x000000000000-0x000000180000 : "u-boot"
0x000000180000-0x0000001a0000 : "u-boot-env"
0x000000200000-0x000000800000 : "uImage"
0x000000800000-0x000001800000 : "minirootfs"
0x000001800000-0x000008000000 : "jffs2"

Quoted 4 lines

Now the boot process is broken. I don't understand why.
It stops right after the network (see below). Usually the boot countdown should appear afterwards.
Is there anything I can do except unsoldering the ROM?

Yes: get control through JTAG.

Quoted 9 lines

If I have to remove the chip and burn it using an external writer... Is there any way to buy similar chip which can be mounted on a socket?

It's a H27U1G8F2BTR-BC (newer version of HY27UF081G2B-TCB) which is NAND flash, 2,7-3,6V, 1Gbitx8 (128 MiB), SLC Single Die + Large Block, TSOP 48 pin. There is also a FBGA 63 PIN available. are there any sockets for FBGA I can solder to TSOP?
Or do other manufacturers offer compatible chips which can be applied to a socket?

Don't consider unsoldering / resoldering, all the more if sockets are involved, as long as you board has JTAG, either as a header or at least as contact points. A dumb JTAG probe and OpenOCD will cost you little and go a long way.

Quoted 3 lines

thanks for any help!

Jan

Amicalement,

Signature · 1 line
Albert.
author
#2 lore raw

hi,

Am 03.04.2013 11:00, schrieb Albert ARIBAUD:

Quoted 5 lines
Quoted 3 lines

apt-get install uboot-envtools
fw_printenv bootcmd

No result there? There should be.

sure.
it's what I set into bootcmd.bak:

Quoted 2 lines
Quoted 2 lines

fw_setenv bootcmd.bak 'nand read.e 0x1200000 0x200000 0x600000;nand read.e 0x2000000 0x800000 0x1000000;bootm 0x1200000 0x2000000'

the outputs all looked fine, after I changed the offset in config file to 0x0. Else I wouln't have written anything. But still I am not 100% sure about the sector size of 0x20000 (128KByte)

Quoted 1 line

Yes: get control through JTAG.

Ok. I'll try.

Quoted 4 lines

Don't consider unsoldering / resoldering, all the more if sockets are involved, as long as you board has JTAG, either as a header or at least as contact points. A dumb JTAG probe and OpenOCD will cost you little and go a long way.

I've got the following soldering points:

- a 1x3 Pin at 2,54mm connector labeld J7 which could be a FAN connector.

- a 2x5=10 PIN at 2mm connector J1 near the ROM chip.

both connectors are on this picture:
http://natisbad.org/NAS/pics/NETGEAR_ReadyNAS_Duo_v2_RND2000-200EUS_J1_and_J7_provisions.jpg

- 1x4 PIN @ 2,54mm connector.

So which one?
Do I have to guess the pins?

which probe should I chose? Something like these?
- Embedded Projects OpenOCD-USB Adapter
- Xilinx JTAG Parallel Cable III FPGA CPLD programmer LPT
- SainSmart USB Blaster Programmer Cable For FPGA CPLD JTAG Development Board
- found a LPT programmer having nothing more than a 74HC244 chip.

Id' prefer the USB adapter...

btw, I found out there is a boot menu.
When I hold the reset button during bootup, there is a boot menu offering:

Normal.

Factory default.
I believe it loads the initrd to reformat the harddrives.

OS Re-install.
Installs the root fs to hard drive from JFFS rom.

Skip volume check.

Memory test.
Performs a memory test.

Disk test.
Maybe Smart test.

I tried most. They all freeze after printing "net: egiga..." except memory test.
Won't help much, I believe, since most rely on the boot process which is broken.

JPT

#3 lore raw

Hi JPT,

Quoted 5 lines · JPT

hi,

Am 03.04.2013 11:00, schrieb Albert ARIBAUD:

Quoted 1 line
Quoted 10 lines
Quoted 4 lines
Quoted 2 lines

apt-get install uboot-envtools
fw_printenv bootcmd

No result there? There should be.

sure.
it's what I set into bootcmd.bak:

Quoted 2 lines
Quoted 2 lines

fw_setenv bootcmd.bak 'nand read.e 0x1200000 0x200000 0x600000;nand read.e 0x2000000 0x800000 0x1000000;bootm 0x1200000 0x2000000'

Ok.

Quoted 3 lines

the outputs all looked fine, after I changed the offset in config file to 0x0. Else I wouln't have written anything. But still I am not 100% sure about the sector size of 0x20000 (128KByte)

Well, the exact value can only be known with the source code for the U-Boot your board is running. Speaking of which... Did you look / ask Netgear for the source code? They should provide it to you as per GPL.

Quoted 15 lines
Quoted 1 line

Yes: get control through JTAG.

Ok. I'll try.

Quoted 4 lines

Don't consider unsoldering / resoldering, all the more if sockets are involved, as long as you board has JTAG, either as a header or at least as contact points. A dumb JTAG probe and OpenOCD will cost you little and go a long way.

I've got the following soldering points:

- a 1x3 Pin at 2,54mm connector labeld J7 which could be a FAN connector.

- a 2x5=10 PIN at 2mm connector J1 near the ROM chip.

Quoted 7 lines

both connectors are on this picture:
http://natisbad.org/NAS/pics/NETGEAR_ReadyNAS_Duo_v2_RND2000-200EUS_J1_and_J7_provisions.jpg

- 1x4 PIN @ 2,54mm connector.

So which one?
Do I have to guess the pins?

Well, without information from Netgear, it's going to be hard to find out which is which. Considering the number of signals in a JTAG I/F, J7 and the 1x4 pin connector can be ruled out. However, it does not mean J1 is JTAG, and anyway, you'll have trouble finding the right pinout.

Quoted 8 lines

which probe should I chose? Something like these?
- Embedded Projects OpenOCD-USB Adapter
- Xilinx JTAG Parallel Cable III FPGA CPLD programmer LPT
- SainSmart USB Blaster Programmer Cable For FPGA CPLD JTAG Development Board
- found a LPT programmer having nothing more than a 74HC244 chip.

Id' prefer the USB adapter...

I cannot advise on the compared merits of those. The ones I know are the BusPirate or BusBlaster (very versatile boards, no casing) and the Olimex ARM-USB-OCD[-H] (less generic than the BusPirate/Blaster but has a casing and comes with a serial port.

In any case, choose a probe for which your JTAG software will work.

Quoted 5 lines

btw, I found out there is a boot menu.
When I hold the reset button during bootup, there is a boot menu offering:
[...]
Won't help much, I believe, since most rely on the boot process which is broken.

I think so too. For now, your best chance for recovery will be JTAG.

BTW, this becomes unrelated to U-Boot per se (at most, it's a non-mainline U-Boot, which should not be discussed here). I suggest moving the discussion outside of this list unless you have generic questions left regarding U-boot.

Amicalement,

Signature · 1 line
Albert.
#4 lore raw
In reply to JPT

Dear JPT,

Quoted 9 lines · JPT
         |  \/  | __ _ _ ____   _____| | |
         | |\/| |/ _` | '__\ \ / / _ \ | |
         | |  | | (_| | |   \ V /  __/ | |
         |_|  |_|\__,_|_|    \_/ \___|_|_|
  _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
  \___/    |____/ \___/ \___/ \__|
Quoted 4 lines

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Feb 6 2012 - 14:40:46) Marvell version: 3.4.27 Netgear version: Uboot-1_1_4-NetgearDUOV3-V1008

On Marvell hardware, you can send a different U-Boot using the serial port, even if the on-flash U-Boot is broken. Have a look at tools/kwboot.c in the mainline U-Boot sources. It uses the serial port to send using the Xmodem protocol, a new U-Boot payload to the Kirkwood SoC.

Best regards,

Thomas

Signature · 4 lines
Thomas Petazzoni, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
#5 lore raw

Hi Thomas,

Quoted 5 lines · Thomas Petazzoni

On Marvell hardware, you can send a different U-Boot using the serial port, even if the on-flash U-Boot is broken. Have a look at tools/kwboot.c in the mainline U-Boot sources. It uses the serial port to send using the Xmodem protocol, a new U-Boot payload to the Kirkwood SoC.

Depends on the SoC. I am the proud owner of a Wireless Space which, due its Kirkwood SoC's revision, cannot recover through UART even though kirkwoods normally can. Not to mention my ED Mini V2, which has orion, with no UART recovery at all.

I did not find if MV88F1155 has UART recovery.

Also, UART recovery requires having a working U-boot image file. JPT, do you have a working (pristine) U-Boot for your ReadyNAS, or can you get one from Netgear?

Quoted 3 lines

Best regards,

Thomas

Amicalement,

Signature · 1 line
Albert.
author
#6 lore raw

Am 04.04.2013 11:17, schrieb Albert ARIBAUD:

Quoted 10 lines

Hi Thomas,

Quoted 5 lines · Thomas Petazzoni

On Marvell hardware, you can send a different U-Boot using the serial port, even if the on-flash U-Boot is broken. Have a look at tools/kwboot.c in the mainline U-Boot sources. It uses the serial port to send using the Xmodem protocol, a new U-Boot payload to the Kirkwood SoC.

mh, there is no kwb* (or kw?b*) neither in the netgear sources nor in stock uboot-1.14

Quoted 8 lines

Depends on the SoC. I am the proud owner of a Wireless Space which, due its Kirkwood SoC's revision, cannot recover through UART even though kirkwoods normally can. Not to mention my ED Mini V2, which has orion, with no UART recovery at all.

Also, UART recovery requires having a working U-boot image file. JPT, do you have a working (pristine) U-Boot for your ReadyNAS, or can you get one from Netgear?

I've got both, source and image.
The first thing I did was reading the ROM to disk :) 1,5M 2013-02-10 20:18 mtd0.uboot.img
128K 2013-02-10 20:18 mtd1.uboot-env.img 6,0M 2013-02-10 20:19 mtd2.kernel.img
2,2M 2013-02-10 20:19 mtd3.initrd.img
89M 2013-02-10 20:17 mtd4.jffs2.img

There is a UART_boot_file.zip included in the source:
32000 2008-06-05 19:35 bb11223344556677_boot.bin

There are a lot of changes in the netgear uboot source.
I don't know where to start.
I cannot find your mail where you wrote about searching for something... o.O

Well, I think easiest would be to try loading the image through serial. Should I start with this?
http://forum.doozan.com/read.php?3,4640,4640,quote=1

Thanks,

Jan

#7 lore raw

Hi JPT,

Quoted 6 lines · JPT

Am 04.04.2013 11:17, schrieb Albert ARIBAUD:

Quoted 5 lines

Hi Thomas,

On Thu, 4 Apr 2013 10:18:15 +0200, Thomas Petazzoni <[email protected]> wrote:

Quoted 8 lines
Quoted 5 lines
Quoted 5 lines

On Marvell hardware, you can send a different U-Boot using the serial port, even if the on-flash U-Boot is broken. Have a look at tools/kwboot.c in the mainline U-Boot sources. It uses the serial port to send using the Xmodem protocol, a new U-Boot payload to the Kirkwood SoC.

mh, there is no kwb* (or kw?b*) neither in the netgear sources nor in stock uboot-1.14

That's because kwb* is an official-U-Boot thing, and u-boot 1.1.4 is way too old, and Netgear sources are based off 1.1.4.

Quoted 9 lines
Quoted 8 lines

Depends on the SoC. I am the proud owner of a Wireless Space which, due its Kirkwood SoC's revision, cannot recover through UART even though kirkwoods normally can. Not to mention my ED Mini V2, which has orion, with no UART recovery at all.

Also, UART recovery requires having a working U-boot image file. JPT, do you have a working (pristine) U-Boot for your ReadyNAS, or can you get one from Netgear?

Quoted 7 lines

I've got both, source and image.
The first thing I did was reading the ROM to disk :) 1,5M 2013-02-10 20:18 mtd0.uboot.img
128K 2013-02-10 20:18 mtd1.uboot-env.img 6,0M 2013-02-10 20:19 mtd2.kernel.img
2,2M 2013-02-10 20:19 mtd3.initrd.img
89M 2013-02-10 20:17 mtd4.jffs2.img

Very wise of you.

Quoted 2 lines

There is a UART_boot_file.zip included in the source:
32000 2008-06-05 19:35 bb11223344556677_boot.bin

Very convenient of Netgear. :)

Quoted 7 lines

There are a lot of changes in the netgear uboot source.
I don't know where to start.
I cannot find your mail where you wrote about searching for something... o.O

Well, I think easiest would be to try loading the image through serial. Should I start with this?
http://forum.doozan.com/read.php?3,4640,4640,quote=1

Since you seem to have a binary meant for UART booting, yes, you might try sending it to the board; with any luck that'll allow you to inspect and possibly revert your U-Boot environment into what it was before the bricking. As to how... any serial app with Xmodem should work, I presume. If the transfer starts, chances are the image will run automatically.

Quoted 3 lines

Thanks,

Jan

Amicalement,

Signature · 1 line
Albert.
#8 lore raw

Dear Albert ARIBAUD,

Quoted 6 lines · Albert ARIBAUD

Since you seem to have a binary meant for UART booting, yes, you might try sending it to the board; with any luck that'll allow you to inspect and possibly revert your U-Boot environment into what it was before the bricking. As to how... any serial app with Xmodem should work, I presume. If the transfer starts, chances are the image will run automatically.

No, any app doing Xmodem will not work. In order to turn the Marvell Kirkwood romcode into UART boot mode, you have to send a series of magic bytes to the UART. This is what kwboot does before sending the binary using the Xmodem protocol.

Best regards,

Thomas

Signature · 4 lines
Thomas Petazzoni, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
#9 lore raw

Hi Thomas,

Quoted 11 lines · Thomas Petazzoni

Dear Albert ARIBAUD,

Quoted 6 lines · Albert ARIBAUD

Since you seem to have a binary meant for UART booting, yes, you might try sending it to the board; with any luck that'll allow you to inspect and possibly revert your U-Boot environment into what it was before the bricking. As to how... any serial app with Xmodem should work, I presume. If the transfer starts, chances are the image will run automatically.

Quoted 4 lines

No, any app doing Xmodem will not work. In order to turn the Marvell Kirkwood romcode into UART boot mode, you have to send a series of magic bytes to the UART. This is what kwboot does before sending the binary using the Xmodem protocol.

Thanks for the correction -- however, it was done already in a private e-mail exchange with JPT, where indeed the requirement became "any app which can send files in raw as well as xmodem modes".

Quoted 3 lines

Best regards,

Thomas

Amicalement,

Signature · 1 line
Albert.