Skip to contentSkip to conversation

ProVideo PV 918A - audi o device created but cannot capture sound

DISCUSSION siddharth 2 participants 4 messages Jan 17, 2014

lore
Share & tools
lore

siddharth

author
#0 lore raw

Hi,

I have installed a ProVideo PV 981.

I was able to get the sound device detected by putting

modprobe snd-bt87x load_all=1 digital_rate=48000 enable=1

but am unable to capture sound. I am using Fedora 19 on an intel i5 machine.

In dmesg i get the error:

[  235.145932] ALSA sound/pci/bt87x.c:860 unknown card 0x878-0xaa00:0x1460
[  235.145935] ALSA sound/pci/bt87x.c:863 please mail id, board name, and,
if it works, the correct digital_rate option to <[email protected]>
[  235.146061] ALSA sound/pci/bt87x.c:931 bt87x0: Using board 0, analog,

digital (rate 48000 Hz)

Any help will be appreciated.

regards
Siddharth

#1 lore raw
Quoted 1 line · siddharth

modprobe snd-bt87x load_all=1 digital_rate=48000 enable=1

You are telling the driver that the tuner chip has a digital output that runs at 48 kHz, and this it is connected to the digital input pin of the Bt878 chip.

Quoted 1 line

but am unable to capture sound.

Do you actually know that your hardware is constructed that way?

How exactly did you try to capture? From which device? (see "arecord -l")

Regards,
Clemens

author
#2 lore raw
Quoted 9 lines · Clemens Ladisch
Quoted 1 line · siddharth

modprobe snd-bt87x load_all=1 digital_rate=48000 enable=1

You are telling the driver that the tuner chip has a digital output that runs at 48 kHz, and this it is connected to the digital input pin of the Bt878 chip.

Quoted 1 line

but am unable to capture sound.

Quoted 8 lines

Do you actually know that your hardware is constructed that way?

How exactly did you try to capture? From which device? (see "arecord -l")

Regards,
Clemens

I tried loading the module without the digital_rate param as well but to no avail.
Am not sure how the card hardware is constructed :( I just tried the digital_rate param after reading in the dmesg that it may work :)

But as soon as I load the module, the sound setting panel in gnome shows 8 audio input devices. a video and a radio input device for each input (there are 4 hardware a/v inputs to the card)

arecord -l shows the following:
card 1: Bt878 [Brooktree Bt878], device 0: Bt87x Digital [Bt87x Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: Bt878 [Brooktree Bt878], device 1: Bt87x Analog [Bt87x Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: Bt878_1 [Brooktree Bt878], device 0: Bt87x Digital [Bt87x Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: Bt878_1 [Brooktree Bt878], device 1: Bt87x Analog [Bt87x Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0

....and so on till card 4.

For capturing, I used vlc alsa://hw:1,1 I also tried 1,0, 2,0 2,1 etc.
Even the sound setting app in gnome does not show any input, which it shows by a flickering equaliser for the native sound card of the machine.

regards
Siddharth

#3 lore raw
Quoted 1 line · siddharth

For capturing, I used vlc alsa://hw:1,1 I also tried 1,0, 2,0 2,1 etc.

It's possible that the tuner does not output anything unless it is actually tuned to something, i.e., you need to run video capture.

Quoted 1 line

Am not sure how the card hardware is constructed

Then it's likely that it's not possible to record the sound that way.

Regards,
Clemens