screen update problems with Intel HD 4600 + virtual screen
A message that is not in the archive (sent off-list or not yet received): [email protected]
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 34 lines · Krzysztof Halasa
Quoted 7 lines · [email protected] (Krzysztof Hałasa) writes:
I'm having screen update problems problems with an Intel HD 4600 with panning + virtual screen. Fedora 20 + updates, CPU is Core i7 4770K, I'm using xrandr --output HDMI1 --panning 4096x2404. The physical screen size is 1920x1200.
Another setup also experiencing this problem is Core i5 4200M with a 1600x900 physical screen (LVDS) and (a bit larger) virtual screen (again with panning).This happens with both UXA and SNA. ATM I'm now using SNA as UXA(?) had some probably unrelated problems with Xvideo (non)updates.
Screen 0: minimum 320 x 200, current 4096 x 2404, maximum 32767 x 32767 VGA1 disconnected (normal left inverted right x axis y axis) HDMI1 connected 4096x2404+0+0 (normal left inverted right x axis y axis) 518mm x 324mm panning 4096x2404+0+0
1920x1200 59.95*+
[etc.]
DP1 disconnected (normal left inverted right x axis y axis) HDMI2 disconnected (normal left inverted right x axis y axis) HDMI3 disconnected (normal left inverted right x axis y axis)It looks with SNA, all is good as long as the screen isn't moved (panned) down more than 7 pixels (i.e. the screen y offset must be 0 - 7 and x offset doesn't matter):
switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 0), rotation normal switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 1), rotation normal switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 2), rotation normal
...
switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 6), rotation normal switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 7), rotation normal
Quoted 8 lines
Now I scroll down 1 pixel:
switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 8), rotation normaland immediately screen isn't updated correctly. For example, an application window is created normally, but when I move it (the app window) down, the top part of the window, max 8 pixels, is left on the screen (the moved window is ok). It almost looks like the code somewhere adds the vertical screen offset twice.
8 is significant as it is the tile row height. The kernel tries to be smart and extract the panning from the surface address so that we can display a larger virtual framebuffer than the hardware can actually use.
Can you reproduce the about sequence with drm.debug=6 dmesg (i.e. echo 6 > /sys/module/drm/parameters/debug ; xrandr --panning... ; dmesg)?
-Chris
Signature · 5 lines
Chris Wilson, Intel Open Source Technology Centre _______________________________________________ Intel-gfx mailing list [email protected] http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 11 lines · Chris Wilson
Quoted 10 lines
switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 7), rotation normal
Now I scroll down 1 pixel:
switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 8), rotation normaland immediately screen isn't updated correctly. For example, an application window is created normally, but when I move it (the app window) down, the top part of the window, max 8 pixels, is left on the screen (the moved window is ok). It almost looks like the code somewhere adds the vertical screen offset twice.
Quoted 7 lines
8 is significant as it is the tile row height. The kernel tries to be smart and extract the panning from the surface address so that we can display a larger virtual framebuffer than the hardware can actually use.
Can you reproduce the about sequence with drm.debug=6 dmesg (i.e. echo 6 >
/sys/module/drm/parameters/debug; xrandr --panning... ; dmesg)?
I'm panning with the mouse. Doesn't look like a lot of output:
no problem yet:
[617996.928] (II) intel(0): switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 7), rotation normal
[618556.836459] [drm:drm_mode_setcrtc], [CRTC:3] [618556.836472] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [618556.836478] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 7) [618556.836484] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [618556.836489] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [618556.836500] [drm:ironlake_update_plane], Writing base 013CA000 0000D200 0 7 16384 [618556.836511] [drm:i915_setup_compression], reserved 39583744 bytes of contiguous stolen space for FBC [618556.836515] [drm:intel_update_fbc], disabling active FBC for update [618556.836520] [drm:ironlake_disable_fbc], disabled FBC [618556.836594] [drm:intel_crtc_cursor_set], cursor off [618556.885876] [drm:gen7_enable_fbc], enabled fbc on plane A [618565.988566] [drm:intel_crtc_cursor_set], cursor off
problems:
[618016.920] (II) intel(0): switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 8), rotation normal
[618576.846085] [drm:drm_mode_setcrtc], [CRTC:3] [618576.846094] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [618576.846098] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 8) [618576.846103] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [618576.846106] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [618576.846114] [drm:ironlake_update_plane], Writing base 013CA000 FFFFFFFFFFFF1200 0 0 16384 [618576.846122] [drm:i915_setup_compression], reserved 39583744 bytes of contiguous stolen space for FBC [618576.846125] [drm:intel_update_fbc], disabling active FBC for update [618576.846128] [drm:ironlake_disable_fbc], disabled FBC [618576.846181] [drm:intel_crtc_cursor_set], cursor off [618576.895986] [drm:gen7_enable_fbc], enabled fbc on plane A [618588.640637] [drm:intel_crtc_cursor_set], cursor off
The kernel is a normal Fedora 20 - Linux 3.14.7-200.fc20.x86_64.
The sequence:
echo 6 > /sys/module/drm/parameters/debug; xrandr --output HDMI1 --panning 4096x2404; dmesg (i.e., only panning setup but no actual panning) produces:
[619598.009625] [drm:drm_mode_getconnector], [CONNECTOR:9:?] [619598.009631] [drm:drm_helper_probe_single_connector_modes_merge_bits], [CONNECTOR:9:VGA-1] [619598.009634] [drm:intel_crt_detect], [CONNECTOR:9:VGA-1] force=1 [619598.009638] [drm:intel_ironlake_crt_detect_hotplug], ironlake hotplug adpa=0xf40000, result 0 [619598.009639] [drm:intel_crt_detect], CRT not detected via hotplug [619598.009807] [drm:gmbus_xfer], GMBUS [i915 gmbus vga] NAK for addr: 0050 r(1) [619598.009810] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga [619598.009812] [drm:intel_crt_get_edid], CRT GMBUS EDID read failed, retry using GPIO bit-banging [619598.009814] [drm:intel_gmbus_force_bit], enabling bit-banging on i915 gmbus vga. force bit now 1 [619598.010186] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus vga [619598.010188] [drm:intel_gmbus_force_bit], disabling bit-banging on i915 gmbus vga. force bit now 0 [619598.010189] [drm:intel_crt_detect_ddc], CRT not detected via DDC:0x50 [no valid EDID found] [619598.010191] [drm:drm_helper_probe_single_connector_modes_merge_bits], [CONNECTOR:9:VGA-1] disconnected [619598.010202] [drm:drm_mode_getconnector], [CONNECTOR:12:?] [619598.010204] [drm:drm_helper_probe_single_connector_modes_merge_bits], [CONNECTOR:12:HDMI-A-1] [619598.010208] [drm:intel_hdmi_detect], [CONNECTOR:12:HDMI-A-1] [619598.060006] [drm:drm_edid_to_eld], ELD monitor EA241WM [619598.060008] [drm:drm_edid_to_eld], ELD size 7, SAD count 0 [619598.060022] [drm:drm_helper_probe_single_connector_modes_merge_bits], [CONNECTOR:12:HDMI-A-1] probed modes : [619598.060024] [drm:drm_mode_debug_printmodeline], Modeline 21:"1920x1200" 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x48 0x9 [619598.060025] [drm:drm_mode_debug_printmodeline], Modeline 26:"1920x1080" 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5 [the list of modes] [619598.060060] [drm:drm_mode_debug_printmodeline], Modeline 40:"720x400" 70 28320 720 738 846 900 400 412 414 449 0x40 0x6 [619598.060070] [drm:drm_mode_getconnector], [CONNECTOR:12:?] [619598.060087] [drm:drm_mode_getconnector], [CONNECTOR:16:?] [619598.060088] [drm:drm_helper_probe_single_connector_modes_merge_bits], [CONNECTOR:16:DP-1] [619598.060090] [drm:intel_dp_detect], [CONNECTOR:16:DP-1] [619598.060091] [drm:drm_helper_probe_single_connector_modes_merge_bits], [CONNECTOR:16:DP-1] disconnected [619598.060093] [drm:drm_mode_getconnector], [CONNECTOR:17:?] [619598.060094] [drm:drm_helper_probe_single_connector_modes_merge_bits], [CONNECTOR:17:HDMI-A-2] [619598.060095] [drm:intel_hdmi_detect], [CONNECTOR:17:HDMI-A-2] [619598.060270] [drm:gmbus_xfer], GMBUS [i915 gmbus dpc] NAK for addr: 0050 r(1) [619598.060271] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpc [619598.060272] [drm:drm_helper_probe_single_connector_modes_merge_bits], [CONNECTOR:17:HDMI-A-2] disconnected [619598.060274] [drm:drm_mode_getconnector], [CONNECTOR:19:?] [619598.060275] [drm:drm_helper_probe_single_connector_modes_merge_bits], [CONNECTOR:19:HDMI-A-3] [619598.060276] [drm:intel_hdmi_detect], [CONNECTOR:19:HDMI-A-3] [619598.060453] [drm:gmbus_xfer], GMBUS [i915 gmbus dpd] NAK for addr: 0050 r(1) [619598.060453] [drm:drm_do_probe_ddc_edid], drm: skipping non-existent adapter i915 gmbus dpd [619598.060454] [drm:drm_helper_probe_single_connector_modes_merge_bits], [CONNECTOR:19:HDMI-A-3] disconnected [619598.066673] [drm:drm_mode_addfb], [FB:55] [619598.066687] [drm:drm_mode_setcrtc], [CRTC:3] [619598.066690] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [619598.066691] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (1394 0) [619598.066693] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [619598.066694] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [619598.082984] [drm:ironlake_update_plane], Writing base 013CA000 FFFFFFFFFFFF75C8 114 0 16384 [619598.092913] [drm:i915_setup_compression], reserved 39583744 bytes of contiguous stolen space for FBC [619598.092915] [drm:intel_update_fbc], disabling active FBC for update [619598.092916] [drm:ironlake_disable_fbc], disabled FBC [619598.093139] [drm:drm_mode_setcrtc], [CRTC:3] [619598.093141] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [619598.093142] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 1204) [619598.093143] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [619598.093144] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [619598.093146] [drm:ironlake_update_plane], Writing base 013CA000 00001200 0 4 16384 [619598.093149] [drm:i915_setup_compression], reserved 39583744 bytes of contiguous stolen space for FBC [619598.093149] [drm:intel_cancel_fbc_work], cancelling pending FBC enable [619598.093236] [drm:drm_mode_setcrtc], [CRTC:3] [619598.093238] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [619598.093238] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (0 0) [619598.093239] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [619598.093240] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [619598.093242] [drm:ironlake_update_plane], Writing base 013CA000 00000000 0 0 16384 [619598.093244] [drm:i915_setup_compression], reserved 39583744 bytes of contiguous stolen space for FBC [619598.093245] [drm:intel_cancel_fbc_work], cancelling pending FBC enable [619598.093805] [drm:drm_mode_setcrtc], [CRTC:3] [619598.093808] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [619598.093809] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2127 0) [619598.093810] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [619598.093812] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [619598.097471] [drm:ironlake_update_plane], Writing base 013CA000 FFFFFFFFFFFF213C 79 0 16384 [619598.097474] [drm:i915_setup_compression], reserved 39583744 bytes of contiguous stolen space for FBC [619598.097475] [drm:intel_cancel_fbc_work], cancelling pending FBC enable [619598.146986] [drm:gen7_enable_fbc], enabled fbc on plane A
Thanks for looking into this.
Signature · 6 lines
Krzysztof Halasa _______________________________________________ [email protected]: X.Org support Archives: http://lists.freedesktop.org/archives/xorg Info: http://lists.x.org/mailman/listinfo/xorg Your subscription address: %(user_address)s
Quoted 43 lines · Krzysztof Halasa
Quoted 11 lines · Chris Wilson
Quoted 10 lines
switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 7), rotation normal
Now I scroll down 1 pixel:
switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 8), rotation normaland immediately screen isn't updated correctly. For example, an application window is created normally, but when I move it (the app window) down, the top part of the window, max 8 pixels, is left on the screen (the moved window is ok). It almost looks like the code somewhere adds the vertical screen offset twice.
Quoted 7 lines
8 is significant as it is the tile row height. The kernel tries to be smart and extract the panning from the surface address so that we can display a larger virtual framebuffer than the hardware can actually use.
Can you reproduce the about sequence with drm.debug=6 dmesg (i.e. echo 6 >
/sys/module/drm/parameters/debug; xrandr --panning... ; dmesg)?I'm panning with the mouse. Doesn't look like a lot of output:
no problem yet:
[617996.928] (II) intel(0): switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 7), rotation normal[618556.836459] [drm:drm_mode_setcrtc], [CRTC:3] [618556.836472] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [618556.836478] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 7) [618556.836484] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [618556.836489] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [618556.836500] [drm:ironlake_update_plane], Writing base 013CA000 0000D200 0 7 16384 [618556.836511] [drm:i915_setup_compression], reserved 39583744 bytes of contiguous stolen space for FBC [618556.836515] [drm:intel_update_fbc], disabling active FBC for update [618556.836520] [drm:ironlake_disable_fbc], disabled FBC [618556.836594] [drm:intel_crtc_cursor_set], cursor off [618556.885876] [drm:gen7_enable_fbc], enabled fbc on plane A [618565.988566] [drm:intel_crtc_cursor_set], cursor offproblems:
[618016.920] (II) intel(0): switch to mode [email protected] on pipe 0 using HDMI1, position (2176, 8), rotation normal
Quoted 12 lines
[618576.846085] [drm:drm_mode_setcrtc], [CRTC:3] [618576.846094] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [618576.846098] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 8) [618576.846103] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [618576.846106] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [618576.846114] [drm:ironlake_update_plane], Writing base 013CA000 FFFFFFFFFFFF1200 0 0 16384 [618576.846122] [drm:i915_setup_compression], reserved 39583744 bytes of contiguous stolen space for FBC [618576.846125] [drm:intel_update_fbc], disabling active FBC for update [618576.846128] [drm:ironlake_disable_fbc], disabled FBC [618576.846181] [drm:intel_crtc_cursor_set], cursor off [618576.895986] [drm:gen7_enable_fbc], enabled fbc on plane A [618588.640637] [drm:intel_crtc_cursor_set], cursor off
Hmm. Whilst it seems odd to have a negative linear offset, I have seen it work elsewhere. Could you try setting
options i915 i915_enable_fbc=0 enable_fbc=0
in /etc/modprobe.conf/intel.conf and rebuilding your initramfs? -Chris
Signature · 1 line
Chris Wilson, Intel Open Source Technology Centre
Quoted 4 lines · Chris Wilson
Hmm. Whilst it seems odd to have a negative linear offset, I have seen it work elsewhere. Could you try setting
options i915 i915_enable_fbc=0 enable_fbc=0
in/etc/modprobe.conf/intel.confand rebuilding your initramfs?
This fixed it.
The negative offset isn't exactly gone, though.
Many thanks.
Would you like me to try something else?
[ 360.440312] [drm:drm_mode_setcrtc], [CRTC:3] [ 360.440325] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [ 360.440330] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 1) [ 360.440336] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [ 360.440342] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [ 360.440352] [drm:ironlake_update_plane], Writing base 013CA000 FFFFFFFFFFFF5200 0 1 16384 [ 360.440430] [drm:intel_crtc_cursor_set], cursor off [ 360.496349] [drm:drm_mode_setcrtc], [CRTC:3] [ 360.496361] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [ 360.496367] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 2) [ 360.496372] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [ 360.496378] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [ 360.496389] [drm:ironlake_update_plane], Writing base 013CA000 FFFFFFFFFFFF9200 0 2 16384 [ 360.496466] [drm:intel_crtc_cursor_set], cursor off [ 361.016807] [drm:drm_mode_setcrtc], [CRTC:3] [ 361.016819] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [ 361.016825] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 3) [ 361.016830] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [ 361.016835] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [ 361.016845] [drm:ironlake_update_plane], Writing base 013CA000 FFFFFFFFFFFFD200 0 3 16384 [ 361.016922] [drm:intel_crtc_cursor_set], cursor off [ 361.873562] [drm:drm_mode_setcrtc], [CRTC:3] [ 361.873576] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [ 361.873582] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 4) [ 361.873587] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [ 361.873592] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [ 361.873602] [drm:ironlake_update_plane], Writing base 013CA000 00001200 0 4 16384 [ 361.873679] [drm:intel_crtc_cursor_set], cursor off [ 362.714307] [drm:drm_mode_setcrtc], [CRTC:3] [ 362.714319] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [ 362.714325] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 5) [ 362.714331] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [ 362.714336] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [ 362.714345] [drm:ironlake_update_plane], Writing base 013CA000 00005200 0 5 16384 [ 362.714423] [drm:intel_crtc_cursor_set], cursor off [ 362.730326] [drm:drm_mode_setcrtc], [CRTC:3] [ 362.730338] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [ 362.730344] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 6) [ 362.730349] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [ 362.730354] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [ 362.730366] [drm:ironlake_update_plane], Writing base 013CA000 00009200 0 6 16384 [ 362.730443] [drm:intel_crtc_cursor_set], cursor off [ 362.826347] [drm:drm_mode_setcrtc], [CRTC:3] [ 362.826356] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [ 362.826361] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 7) [ 362.826365] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [ 362.826369] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [ 362.826377] [drm:ironlake_update_plane], Writing base 013CA000 0000D200 0 7 16384 [ 362.826439] [drm:intel_crtc_cursor_set], cursor off [ 362.954525] [drm:drm_mode_setcrtc], [CRTC:3] [ 362.954536] [drm:drm_mode_setcrtc], [CONNECTOR:12:HDMI-A-1] [ 362.954542] [drm:intel_crtc_set_config], [CRTC:3] [FB:55] #connectors=1 (x y) (2176 8) [ 362.954548] [drm:intel_set_config_compute_mode_changes], computed changes for [CRTC:3], mode_changed=0, fb_changed=1 [ 362.954553] [drm:intel_modeset_stage_output_state], [CONNECTOR:12:HDMI-A-1] to [CRTC:3] [ 362.954564] [drm:ironlake_update_plane], Writing base 013CA000 FFFFFFFFFFFF1200 0 0 16384 [ 362.954641] [drm:intel_crtc_cursor_set], cursor off
Signature · 6 lines
Krzysztof Halasa _______________________________________________ [email protected]: X.Org support Archives: http://lists.freedesktop.org/archives/xorg Info: http://lists.x.org/mailman/listinfo/xorg Your subscription address: %(user_address)s
Quoted 7 lines · Krzysztof Halasa
Quoted 4 lines · Chris Wilson
Hmm. Whilst it seems odd to have a negative linear offset, I have seen it work elsewhere. Could you try setting
options i915 i915_enable_fbc=0 enable_fbc=0
in/etc/modprobe.conf/intel.confand rebuilding your initramfs?
Quoted 5 lines
This fixed it.
The negative offset isn't exactly gone, though.
Many thanks.Would you like me to try something else?
I'll leave that to Daniel to try and combine FBC with CRTC viewports... -Chris
Signature · 1 line
Chris Wilson, Intel Open Source Technology Centre
Quoted 1 line · Chris Wilson
I'll leave that to Daniel to try and combine FBC with CRTC viewports...
Let me know if you need more tests, this problems happens on both my i5 4200M laptop and on a desktop PC with i7 4770k (this machine, now fixed).
Signature · 6 lines
Krzysztof Halasa _______________________________________________ [email protected]: X.Org support Archives: http://lists.freedesktop.org/archives/xorg Info: http://lists.x.org/mailman/listinfo/xorg Your subscription address: %(user_address)s
Quoted 7 lines · Krzysztof Halasa
Quoted 1 line · Chris Wilson
I'll leave that to Daniel to try and combine FBC with CRTC viewports...
Let me know if you need more tests, this problems happens on both my i5 4200M laptop and on a desktop PC with i7 4770k (this machine, now fixed).
I'll file it under stuff we need to fix before enabling fbc for real. And we need a testcase for this, too. For now I guess you have to life with disabling fbc.
-Daniel
Signature · 3 lines
Daniel Vetter Software Engineer, Intel Corporation +41 (0) 79 365 57 48 - http://blog.ffwll.ch