Skip to contentSkip to conversation

cbq-fw classifier

LARTC vanitha 2 participants 5 messages Nov 1, 2001 – Nov 2, 2001

lore
Share & tools
lore

vanitha

author
#0 lore raw

Hi All,

I was using CBQ to control the bandwidth rate , while i use the qdisc cbq with u32 filter and route filter it is working fine ,but when i use fw classifier it seems that the bandwidth rate 100kbit is not picked.

i have used the following commands

/sbin/iptables -I PREROUTING -t mangle -p tcp -d 172.16.1.81 -j MARK --set-mark 1

/sbin/tc qdisc add dev eth0 root handle 1: cbq bandwidth 10Mbit cell 8 avpkt 1000 mpu 64
/sbin/tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit rate 10Mbit allot 1514 cell 8 weight 1Mbit prio 8 maxburst 20 avpkt 1000 /sbin/tc class add dev eth0 parent 1:1 classid 1:2 cbq bandwidth 10Mbit rate 100Kbit allot 1514 cell 8 weight 10Kbit prio 3 maxburst 20 avpkt 1000

/sbin/tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 1 fw classid 1:2

is that anything i have missed out ?
i have tested these commands using Linux-2.4.10.

Advance Thanks
Vanitha

#1 lore raw

please use
tc -s qdisc show dev eth1 tc -s class show dev eth1 tc -s filter show dev eth1

to see where the packet goes ,
or how much it borrows .....
It seems your script can't regular the classid 1:2

cheers

john
----- Original Message -----
From: vanitha
To: [email protected]
Sent: Thursday, November 01, 2001 5:04 PM
Subject: [LARTC] cbq-fw classifier

Hi All,

I was using CBQ to control the bandwidth rate , while i use the qdisc cbq with u32 filter and route filter it is working fine ,but when i use fw classifier it seems that the bandwidth rate 100kbit is not picked.

i have used the following commands

  /sbin/iptables -I PREROUTING -t mangle -p tcp -d 172.16.1.81 -j MARK --set-mark 1

/sbin/tc qdisc add dev eth0 root handle 1: cbq bandwidth 10Mbit cell 8 avpkt 1000 mpu 64
/sbin/tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit rate 10Mbit allot 1514 cell 8 weight 1Mbit prio 8 maxburst 20 avpkt 1000 /sbin/tc class add dev eth0 parent 1:1 classid 1:2 cbq bandwidth 10Mbit rate 100Kbit allot 1514 cell 8 weight 10Kbit prio 3 maxburst 20 avpkt 1000

/sbin/tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 1 fw classid 1:2

is that anything i have missed out ?
i have tested these commands using Linux-2.4.10.

Advance Thanks
Vanitha

author
#2 lore raw
In reply to vanitha

Hello John ,

Thanks for ur reply . But still it have not worked out.
i have attached the results is that iam making some mistakes in script please guide me

Advance Thanks
vanitha

/sbin/tc -s qdisc show dev eth0

qdisc cbq 1: rate 10Mbit (bounded,isolated) prio no-transmit Sent 450 bytes 6 pkts (dropped 0, overlimits 0) borrowed 0 overactions 0 avgidle 624 undertime 0

/sbin/tc -s filter show dev eth0
filter parent 1: protocol ip pref 1 fw
filter parent 1: protocol ip pref 1 fw handle 0x1 classid 1:2

/sbin/tc -s class show dev eth0

class cbq 1: root rate 10Mbit (bounded,isolated) prio no-transmit
Sent 3725 bytes 47 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:1 parent 1: rate 10Mbit prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:2 parent 1:1 rate 100Kbit (bounded) prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 1.79878e+06 undertime 0

/sbin/iptables -t mangle -L

Chain PREROUTING (policy ACCEPT)

target     prot opt source               destination
MARK       tcp  --  anywhere             172.16.1.81        MARK set 0x1

Chain OUTPUT (policy ACCEPT)
target prot opt source destination

----- Original Message -----
From: john peng
To: vanitha ; [email protected]
Sent: Sunday, December 02, 2001 5:01 AM
Subject: Re: [LARTC] cbq-fw classifier

please use
tc -s qdisc show dev eth1
tc -s class show dev eth1
tc -s filter show dev eth1

to see where the packet goes ,
or how much it borrows .....
It seems your script can't regular the classid 1:2

cheers

john
----- Original Message -----
From: vanitha
To: [email protected]
Sent: Thursday, November 01, 2001 5:04 PM
Subject: [LARTC] cbq-fw classifier

Hi All,

I was using CBQ to control the bandwidth rate , while i use the qdisc cbq with u32 filter and route filter it is working fine ,but when i use fw classifier it seems that the bandwidth rate 100kbit is not picked.

i have used the following commands

/sbin/iptables -I PREROUTING -t mangle -p tcp -d 172.16.1.81 -j MARK --set-mark 1

/sbin/tc qdisc add dev eth0 root handle 1: cbq bandwidth 10Mbit cell 8 avpkt 1000 mpu 64
/sbin/tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit rate 10Mbit allot 1514 cell 8 weight 1Mbit prio 8 maxburst 20 avpkt 1000 /sbin/tc class add dev eth0 parent 1:1 classid 1:2 cbq bandwidth 10Mbit rate 100Kbit allot 1514 cell 8 weight 10Kbit prio 3 maxburst 20 avpkt 1000

/sbin/tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 1 fw classid 1:2

is that anything i have missed out ?
i have tested these commands using Linux-2.4.10.

Advance Thanks
Vanitha

#3 lore raw
In reply to vanitha

According to the results ,
packets are not filtered into classid 1:2
what is your testing scenario ?

(notice , PREROUTING don't tack care of local generating packets )

john
----- Original Message -----
From: vanitha
To: john peng ; [email protected]
Sent: Thursday, November 01, 2001 8:43 PM
Subject: Re: [LARTC] cbq-fw classifier

Hello John ,

Thanks for ur reply . But still it have not worked out.
i have attached the results is that iam making some mistakes in script please guide me

Advance Thanks
vanitha

/sbin/tc -s qdisc show dev eth0

qdisc cbq 1: rate 10Mbit (bounded,isolated) prio no-transmit Sent 450 bytes 6 pkts (dropped 0, overlimits 0) borrowed 0 overactions 0 avgidle 624 undertime 0

/sbin/tc -s filter show dev eth0
filter parent 1: protocol ip pref 1 fw
filter parent 1: protocol ip pref 1 fw handle 0x1 classid 1:2

/sbin/tc -s class show dev eth0

class cbq 1: root rate 10Mbit (bounded,isolated) prio no-transmit
Sent 3725 bytes 47 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:1 parent 1: rate 10Mbit prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:2 parent 1:1 rate 100Kbit (bounded) prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 1.79878e+06 undertime 0

/sbin/iptables -t mangle -L

Chain PREROUTING (policy ACCEPT)

  target     prot opt source               destination
  MARK       tcp  --  anywhere             172.16.1.81        MARK set 0x1

Chain OUTPUT (policy ACCEPT)
target prot opt source destination

----- Original Message -----
From: john peng
To: vanitha ; [email protected]
Sent: Sunday, December 02, 2001 5:01 AM
Subject: Re: [LARTC] cbq-fw classifier

please use
tc -s qdisc show dev eth1
tc -s class show dev eth1
tc -s filter show dev eth1

to see where the packet goes ,
or how much it borrows .....
It seems your script can't regular the classid 1:2

cheers

john
----- Original Message -----
From: vanitha
To: [email protected]
Sent: Thursday, November 01, 2001 5:04 PM
Subject: [LARTC] cbq-fw classifier

Hi All,

I was using CBQ to control the bandwidth rate , while i use the qdisc cbq with u32 filter and route filter it is working fine ,but when i use fw classifier it seems that the bandwidth rate 100kbit is not picked.

i have used the following commands

/sbin/iptables -I PREROUTING -t mangle -p tcp -d 172.16.1.81 -j MARK --set-mark 1

/sbin/tc qdisc add dev eth0 root handle 1: cbq bandwidth 10Mbit cell 8 avpkt 1000 mpu 64
/sbin/tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit rate 10Mbit allot 1514 cell 8 weight 1Mbit prio 8 maxburst 20 avpkt 1000 /sbin/tc class add dev eth0 parent 1:1 classid 1:2 cbq bandwidth 10Mbit rate 100Kbit allot 1514 cell 8 weight 10Kbit prio 3 maxburst 20 avpkt 1000

/sbin/tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 1 fw classid 1:2

is that anything i have missed out ?
i have tested these commands using Linux-2.4.10.

Advance Thanks
Vanitha

author
#4 lore raw
In reply to vanitha

hello john

When i changed my iptable script from PREROUTING to OUTPUT it worked fine.
I have another query
can i mark the outgoing packets by using the mac address (in the below case i have used the ip address)

Advance Thanks
Vanitha
----- Original Message -----
From: john peng
To: vanitha ; [email protected]
Sent: Sunday, December 02, 2001 7:29 AM
Subject: Re: [LARTC] cbq-fw classifier

According to the results ,
packets are not filtered into classid 1:2
what is your testing scenario ?

(notice , PREROUTING don't tack care of local generating packets )

john
----- Original Message -----
From: vanitha
To: john peng ; [email protected]
Sent: Thursday, November 01, 2001 8:43 PM
Subject: Re: [LARTC] cbq-fw classifier

Hello John ,

Thanks for ur reply . But still it have not worked out.
i have attached the results is that iam making some mistakes in script please guide me

Advance Thanks
vanitha

/sbin/tc -s qdisc show dev eth0

qdisc cbq 1: rate 10Mbit (bounded,isolated) prio no-transmit Sent 450 bytes 6 pkts (dropped 0, overlimits 0) borrowed 0 overactions 0 avgidle 624 undertime 0

/sbin/tc -s filter show dev eth0
filter parent 1: protocol ip pref 1 fw
filter parent 1: protocol ip pref 1 fw handle 0x1 classid 1:2

/sbin/tc -s class show dev eth0

class cbq 1: root rate 10Mbit (bounded,isolated) prio no-transmit
Sent 3725 bytes 47 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:1 parent 1: rate 10Mbit prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 624 undertime 0
class cbq 1:2 parent 1:1 rate 100Kbit (bounded) prio 1
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
borrowed 0 overactions 0 avgidle 1.79878e+06 undertime 0

/sbin/iptables -t mangle -L

Chain PREROUTING (policy ACCEPT)
target prot opt source destination
MARK tcp -- anywhere 172.16.1.81 MARK set 0x1

Chain OUTPUT (policy ACCEPT)
target prot opt source destination

----- Original Message -----
From: john peng
To: vanitha ; [email protected]
Sent: Sunday, December 02, 2001 5:01 AM
Subject: Re: [LARTC] cbq-fw classifier

please use
tc -s qdisc show dev eth1
tc -s class show dev eth1
tc -s filter show dev eth1

to see where the packet goes ,
or how much it borrows .....
It seems your script can't regular the classid 1:2

cheers

john
----- Original Message -----
From: vanitha
To: [email protected]
Sent: Thursday, November 01, 2001 5:04 PM
Subject: [LARTC] cbq-fw classifier

Hi All,

I was using CBQ to control the bandwidth rate , while i use the qdisc cbq with u32 filter and route filter it is working fine ,but when i use fw classifier it seems that the bandwidth rate 100kbit is not picked.

i have used the following commands

/sbin/iptables -I PREROUTING -t mangle -p tcp -d 172.16.1.81 -j MARK --set-mark 1

/sbin/tc qdisc add dev eth0 root handle 1: cbq bandwidth 10Mbit cell 8 avpkt 1000 mpu 64
/sbin/tc class add dev eth0 parent 1:0 classid 1:1 cbq bandwidth 10Mbit rate 10Mbit allot 1514 cell 8 weight 1Mbit prio 8 maxburst 20 avpkt 1000 /sbin/tc class add dev eth0 parent 1:1 classid 1:2 cbq bandwidth 10Mbit rate 100Kbit allot 1514 cell 8 weight 10Kbit prio 3 maxburst 20 avpkt 1000

/sbin/tc filter add dev eth0 protocol ip parent 1:0 prio 1 handle 1 fw classid 1:2

is that anything i have missed out ?
i have tested these commands using Linux-2.4.10.

Advance Thanks
Vanitha