Virtual circuits
Hi, I see this topic in LARTC:
Virtual Circuits over TCP/IP sockets
I'm interesting about this, I know that in FreeBSD it's posible via netgraph but I didn't see any usable solutions for linux. I know about Frame Diverter but it's not suitable for my purpose.
My problem: I have breezenet microwave network with some nodes which are routed and my clients want use my network as a transport net and want to have point-to-point connection.
Fig. Topology of network
client1
||
~~~~~~~~~~~~~~~~~~~~~~~~~~~~microwave network~~~~~~~~~~~~~~~~~~~~~~~ Access_point --- |switch| --- Node_router1
/
/
/
Node_router2
/
/
/
Node_router3 --- |switch| --- Access_point
~~~~~~~~~~~~~~~~~~~~~~~~~~~microwave network~~~~~~~~~~~~~~~~~~~~~~~
||
client1_routerHow to sent _everything_ (e.g. arp) from client1 to client1_router? I cant use any tunnel.
It's posible with linux ?
With regards
PSIkappa
psi _at_ atlantis.sk
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 3 lines · M.F. PSIkappa
I'm interesting about this, I know that in FreeBSD it's posible via netgraph but I didn't see any usable solutions for linux. I know about Frame Diverter but it's not suitable for my purpose.
This is not what these Virtual Circuits are - the VCs I mention are ATM vc's, not 'bridging tunnels'.
Quoted 3 lines
How to sent _everything_ (e.g. arp) from client1 to
client1_router? I cant use any tunnel.
It's posible with linux ?
Well, you can use a tunnel, it's just that you want a 'bridging tunnel', that appears by magic so to speak. Basically you are then a two-port repeater with a long bit in the middle.
Now, is this possible? I think it is, I'm just not entire sure how.
Perhaps a proxy-arping pseudo bridge does what you want? In that case ARPs are not transmitted over your tunnel, but your tunnel device reacts to ARP requests for hosts it knows about on the other side.
If you want a real bridge, you should find a way to create a 'virtual interface' that lives on the remote host, and run a bridge between your regular interface and the 'virtual long distance' one.
Perhaps this is possible.
Regards,
bert
Signature · 8 lines
http://www.PowerDNS.com Versatile DNS Software & Services Trilab The Technology People Netherlabs BV / Rent-a-Nerd.nl - Nerd Available - 'SYN! .. SYN|ACK! .. ACK!' - the mating call of the internet _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 23 lines · bert hubert
Quoted 3 lines · M.F. PSIkappa
I'm interesting about this, I know that in FreeBSD it's posible via netgraph but I didn't see any usable solutions for linux. I know about Frame Diverter but it's not suitable for my purpose.
This is not what these Virtual Circuits are - the VCs I mention are ATM vc's, not 'bridging tunnels'.
Quoted 3 lines
How to sent _everything_ (e.g. arp) from client1 to
client1_router? I cant use any tunnel.
It's posible with linux ?Well, you can use a tunnel, it's just that you want a 'bridging tunnel', that appears by magic so to speak. Basically you are then a two-port repeater with a long bit in the middle.
Now, is this possible? I think it is, I'm just not entire sure how.
Perhaps a proxy-arping pseudo bridge does what you want? In that case ARPs are not transmitted over your tunnel, but your tunnel device reacts to ARP requests for hosts it knows about on the other side.
Quoted 5 lines
If you want a real bridge, you should find a way to create a 'virtual interface' that lives on the remote host, and run a bridge between your regular interface and the 'virtual long distance' one.
Perhaps this is possible.
Yes it is, by using CIPE and the normal ethernet bridge you can do exactly this. CIPE is an encrypted tunnel that creates a virtual ethernet interface that can be used for bridging.
http://sites.inka.de/bigred/devel/cipe.html
"it is even possible to run an Ethernet bridge over CIPE"
It says it only works with the bridge in kernel 2.4 or using a patched 2.2
Hope it helps.
/Martin
Never argue with an idiot. They drag you down to their level, then beat you with experience.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
Quoted 9 lines · bert hubert
Quoted 3 lines
How to sent _everything_ (e.g. arp) from client1 to
client1_router? I cant use any tunnel.
It's posible with linux ?Well, you can use a tunnel, it's just that you want a 'bridging tunnel', that appears by magic so to speak. Basically you are then a two-port repeater with a long bit in the middle.
Now, is this possible? I think it is, I'm just not entire sure how.
This is possible, using vtund + bridging as found in the kernel - the only question is whether you need to be able to filter or use QoS on that traffic
- since that isn't possible (well, my experience was that that's not possible, maybe it is right now!)
I've had this setup working however, the arp and netbios broadcasts flooded the connection over which I was tunneling - rendering it quite useless ;)
Regards,
Jasper
Signature · 8 lines
Q_. Jasper Spaans <[email protected]> `~\ http://jsp.ds9a.nl/ Mr /\ Tel/Fax: +31-84-8749842 Zap Move '.sig' for great justice! _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/