Skip to contentSkip to conversation

Forcing an "external" route

LARTC David Purves 3 participants 4 messages Dec 7, 2001

lore
Share & tools
lore
#0 lore raw

Here is as wacky a situation as you might find...

    Given a linux box with two ethernet cards:
        eth0  at ip 192.168.100
        eth1 at ip 172.16.1.100,
    and an internet "appliance" with two ethernet ports:
        p0 at ip 192.168.1.101
        p1 at ip 172.16.1.1,

    I want to force packets from     eth0 <--> eth1     to take the path 
    eth0 <--> p0 <--> p1<-->eth1.

What I have here is an appliance that I want to run some throughput tests.

The cables are set up eth0 <--> p0 and p1<-->eth1 and work (pings work just fine)....
no matter what I try, the kernel is too smart for me :-) , and it
routes internally (inside the linux box) instead of entering the outside world.

Any ideas?

David Purves

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/

#1 lore raw
Quoted 10 lines · David Purves
    I want to force packets from     eth0 <--> eth1     to take the path 
    eth0 <--> p0 <--> p1<-->eth1.

What I have here is an appliance that I want to run some throughput tests.

The cables are set up eth0 <--> p0 and p1<-->eth1 and work (pings work just fine)....
no matter what I try, the kernel is too smart for me :-) , and it
routes internally (inside the linux box) instead of entering the outside world.

I don't think that this is possible purely with iproute2. You will probably need at least one extra machine to perform NAT.

Perhaps you can get away with UML (usermodelinux).

Regards,

bert

Signature · 8 lines
http://www.PowerDNS.com          Versatile DNS Software & Services
Trilab                                 The Technology People
Netherlabs BV / Rent-a-Nerd.nl           - Nerd Available -
'SYN! .. SYN|ACK! .. ACK!' - the mating call of the internet

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
#2 lore raw
In reply to David Purves
Quoted 4 lines · Greg Scott

What if you used some iptables rules to DENY packets from eth0 with destination ip address 172.16.1.100? I'm thinking you might have to put in the rules in the OUTPUT table and catch them on the way out from 192.168.1.100. No clue whether or not that will work, but worth a try.

That just drops the packets. You might try some DNAT stuff on the iptables POSTROUTING chain, perhaps that works. I think it might.

Regards,

bert

Signature · 8 lines
http://www.PowerDNS.com          Versatile DNS Software & Services
Trilab                                 The Technology People
Netherlabs BV / Rent-a-Nerd.nl           - Nerd Available -
'SYN! .. SYN|ACK! .. ACK!' - the mating call of the internet

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/
#3 lore raw
In reply to David Purves

What if you used some iptables rules to DENY packets from eth0 with destination ip address 172.16.1.100? I'm thinking you might have to put in the rules in the OUTPUT table and catch them on the way out from 192.168.1.100. No clue whether or not that will work, but worth a try.

- Greg

-----Original Message-----
From: David Purves [mailto:[email protected]]
Sent: Friday, December 07, 2001 3:39 PM
To: [email protected]
Subject: [LARTC] Forcing an "external" route

Here is as wacky a situation as you might find...

    Given a linux box with two ethernet cards:
        eth0  at ip 192.168.100
        eth1 at ip 172.16.1.100,
    and an internet "appliance" with two ethernet ports:
        p0 at ip 192.168.1.101
        p1 at ip 172.16.1.1,

    I want to force packets from     eth0 <--> eth1     to take the path 
    eth0 <--> p0 <--> p1<-->eth1.

What I have here is an appliance that I want to run some throughput tests.

The cables are set up eth0 <--> p0 and p1<-->eth1 and work (pings work just fine)....
no matter what I try, the kernel is too smart for me :-) , and it
routes internally (inside the linux box) instead of entering the outside world.

Any ideas?

David Purves

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
http://ds9a.nl/2.4Routing/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/2.4Routing/