sfq as solution to "Small ISP problems" and "How could I do this?"
Quoted 4 lines
Subject: [LARTC] Small ISP problems (CBQ)
First of all, this is what we want (in network priority order):
1: SSH - to be realtime always.
I don't think you want this to always be high prio - that includes scp.
Quoted 1 line
2: HTTP to be fast, always.
Clearly can't be done if you have more http requests than your bandwidth can handle.
Quoted 2 lines
3-> ftp, direct-connect, kazaa and others to be throttled to X bandwidh per IP.. (or not disturb http and ssh and use real fair quing.. )
I think what you really want is to prevent large flows from unfairly impacting small ones, and that's what sfq does. Try it and see whether you get the behavior you want.
========
Quoted 4 lines
Subject: [LARTC] How could I do this?
If I want to limit bandwidth from a lot of ip addresses( every ip has a limit),
Again, I wonder if this is really what you want. You really want to waste extra bandwidth? Normally if you have 10 users you'd be willing to let one use all of the bandwidth whenever none of the others want any. Now it's possible for an ISP that you promise some particular bandwidth to each customer and don't want to give him more unless he pays for it. That's another situation.
If you're really in the first situation where you just want to give equal service to all who are requesting it then what you really want is a slight variant of sfq. If you look at the code you'll see a hash function that takes into consideration source and destination ip address and port and maybe other stuff. All you want to do is remove all but the source IP (and then perhaps do what you can to prevent source forgery!). That will give fair service among all source IP addresses.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Quoted 4 lines
Quoted 3 lines
Subject: [LARTC] Small ISP problems (CBQ)
First of all, this is what we want (in network priority order):
1: SSH - to be realtime always.I don't think you want this to always be high prio - that includes scp.
your'e right, only the real ssh traffic..
Quoted 4 lines
Quoted 2 lines
2: HTTP to be fast, always.
Clearly can't be done if you have more http requests than your bandwidth can handle.
That is a fact yes..
Let me rephrase it then. I don't want the http traffic to be slowed down by for e.g ftp-data traffic...
Quoted 7 lines
Quoted 1 line
3-> ftp, direct-connect, kazaa and others to be throttled to X
bandwidh per
Quoted 1 line
IP.. (or not disturb http and ssh and use real fair quing.. )
I think what you really want is to prevent large flows from unfairly impacting small ones, and that's what sfq does. Try it and see whether you get the behavior you want.
Oki, I tried it. I defined two classes. "all_in" and "all_out". I have 2Mbit full duplex so just to be sure my que isn't ending up in the g703 "modem" I defined the classes to 1,900Mbit downstream and 1,000Mbit upstream.
Put SFQ on both classes and tested under heavy load..
Well, My ssh isn't working very well.. :/
Quoted 4 lines
========
Quoted 1 line
Subject: [LARTC] How could I do this?
Quoted 8 lines
Quoted 2 lines
If I want to limit bandwidth from a lot of ip addresses( every ip has a limit),
Again, I wonder if this is really what you want. You really want to waste extra bandwidth? Normally if you have 10 users you'd be willing to let one use all of the bandwidth whenever none of the others want any. Now it's possible for an ISP that you promise some particular bandwidth to each customer and don't want to give him more unless he pays for it. That's another situation.
yes it is, the primary is to make sure ssh is always moving fast, http to and bulk traffic like ftp-data on a low priority, not disturbing the other two.
Quoted 3 lines
If you're really in the first situation where you just want to give equal service to all who are requesting it then what you really want is a slight variant of sfq. If you look at the code you'll see a hash
function that takes into consideration source and destination ip
What code exactly ? I am currently using the cbq.init script version 0.6.2 .
Quoted 4 lines
address and port and maybe other stuff. All you want to do is remove all but the source IP (and then perhaps do what you can to prevent source forgery!). That will give fair service among all source IP addresses.
Ok..
Take a look at this:
Right now my bandwidth looks like this:
Total Rates: 2170.6 kbits/s
517.6 packets/sec
Incoming rates: 1769.4 kbits/s
261.4 packets/sec
Outgoing rates: 401.2 kbits/sec
256.2 packets/sec
Well, we have a full duplex 2Mbit connection so this should not be a problem.
Eventhough, we, based on a 265 packets test, have 28% packet loss witch is not good.
Since the bandwidh is not close to 1900kbit/s who is the class maximum
"class cbq 1: root rate 1900Kbit (bounded,isolated) prio no-transmit
Sent 1339557 bytes 1848 pkts (dropped 0, overlimits 0) "
I wonder, will cbq still do prioritization ?
What about the que.. Will it move for e.g ssh always first in the que or what happens ?
(rtfm.. yep, been doing that, but this is just not easy.. )
My idea was to have a "mother" cbq class, cbq.0010.everything_in, defined by me, doing SFQ on everything. The RULE is for the whole network, like 10.0.0.0/24.
A doughter class to that is cbq.0065.ssh_in.
The thing though is that the ssh_in class never gets any data. Probably since rule of the mother class always triggers on the packet and it's never being sent down to the ssh class.
If I define the ssh class outside the "everything_in" class, and gives it a classid thats lover then the everything_in class it gets data though. The quality of the ssh link doesn't seem to change though.. Hmmz.. I'm starting to think that we might have some problem somewhere else in the network...
/ Paul
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/