Skip to contentSkip to conversation

arp-proxy and advanced routing problem

LARTC Arne Hueggenberg 2 participants 3 messages Dec 11, 2001

lore
Share & tools
lore
#0 lore raw

Hi,

i have a problem with my setup.
The box has 3 interfaces
to the cable modem,
to the dsl modem
to the switch serving our other boxes

all boxes on the switch have static ips
behind the cable modem is a subnet with hosts with static ips on the sae subnet
in behind the cable modem is also the default

the arp-proxying is done between the cable interface and the switch interface

the third goes to the adsl modem
we do masqing on this interface

now, some of the boxes on the switch are supposed to go out over the adsl line, and some are supposed to go via the gateway behind the cable modem. default route via the adsl, and a seperate table for those supposed to go via the cable.

Now, when we add that table everything works as its supposed to. But if a windows box reboots it suddenly complains the switch interface had its ip and doesent configure the interface
if we remove the table it boots fine

Anyone have an idea what might be the problem?

Signature · 6 lines
Arne 'zal' Hueggenberg <[email protected]>


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
#1 lore raw

Hello,

Quoted 23 lines · Arne Hueggenberg

Hi,

i have a problem with my setup.
The box has 3 interfaces
to the cable modem,
to the dsl modem
to the switch serving our other boxes

all boxes on the switch have static ips
behind the cable modem is a subnet with hosts with static ips on the sae subnet
in behind the cable modem is also the default

the arp-proxying is done between the cable interface and the switch interface

the third goes to the adsl modem
we do masqing on this interface

now, some of the boxes on the switch are supposed to go out over the adsl line, and some are supposed to go via the gateway behind the cable modem. default route via the adsl, and a seperate table for those supposed to go via the cable.

Quoted 6 lines

Now, when we add that table everything works as its supposed to. But if a windows box reboots it suddenly complains the switch interface had its ip and doesent configure the interface
if we remove the table it boots fine

Anyone have an idea what might be the problem?

It seems the proxy ARP feature is activated for wrong route.
See the following URL and try to differentiate your devices by the medium they are attached to. Then your router will know that the target host can see the broadcast probes and will not reply for them. For this to work, you need correct routes. The problem can be that the proxy_arp feature does not know that two devices are attached to same medium and the ARP reply should not be generated.

http://www.linuxvirtualserver.org/~julian/#medium_id

As I can't fully understand your settings, if you have some questions, please provide some settings. And of course, the main thing: how many distinct mediums you have. Read medium_id.txt for more information.

Regards

--
Julian Anastasov <[email protected]>

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#2 lore raw
In reply to Arne Hueggenberg
Quoted 42 lines · you

Hello,

Quoted 24 lines · Arne Hueggenberg

Hi,

i have a problem with my setup.
The box has 3 interfaces
to the cable modem,
to the dsl modem
to the switch serving our other boxes

all boxes on the switch have static ips
behind the cable modem is a subnet with hosts with static ips on the sae subnet
in behind the cable modem is also the default

the arp-proxying is done between the cable interface and the switch interface

the third goes to the adsl modem
we do masqing on this interface

now, some of the boxes on the switch are supposed to go out over the adsl line, and some are supposed to go via the gateway behind the cable modem. default route via the adsl, and a seperate table for those supposed to go via the cable.

Quoted 6 lines

Now, when we add that table everything works as its supposed to. But if a windows box reboots it suddenly complains the switch interface had its ip and doesent configure the interface
if we remove the table it boots fine

Anyone have an idea what might be the problem?

It seems the proxy ARP feature is activated for wrong route.
See the following URL and try to differentiate your devices by the medium they are attached to. Then your router will know that the target host can see the broadcast probes and will not reply for them. For this to work, you need correct routes. The problem can be that the proxy_arp feature does not know that two devices are attached to same medium and the ARP reply should not be generated.

Quoted 6 lines

http://www.linuxvirtualserver.org/~julian/#medium_id

As I can't fully understand your settings, if you have some questions, please provide some settings. And of course, the main thing: how many distinct mediums you have. Read medium_id.txt for more information.

{public subnet with gateway} -- --[cable modem]

                                                                         |
                                                                         |
 [box 1 with ip on public subnet]                |
                                          \                        /   |
                                           \         proxy-arp  |
                                           \                 /          |
                                            [switch]-- - - - -linux router}
                                          /                             |
                                       /                                |
 [box 2 with ip on public subnet]                |
                                                                         |
                                                                         |
                                                                 [adsl-modem]
                                                                         |
                                                                         |
                                                                         |
                                                                        ISP

So the linux router has 3 ethernet cards
proxy arp is needed between the switch and the cable modem
reason being that the cable modems use Time Division Multiplexing, and with everyone her using his own cable modem performance goes against 0 unfortunalty the cable modems only work with a single mac adress on the other end, so we have to do proxy arp

now, box 1 is supposed to be routed via the gateway behind the dsl line, and box 2 is supposed to be routed via the gateway on the subnet behind the cable modem.

Wich works fine if i add the necessary rules, except for the fact that if box 1 wich runs windows is rebooted it complains about the linux router stealing its ip adress

so the linux router has host routes for box1 and box2, a network route for the public subnet and a default route over the DSL, with an table for box specifying the gateway behind the cable modem as default route

only that when the tables up we run into problems with the proxy-arp

cant access the box right now so i cant post configuration yet, but will as soon as its back up

Quoted 4 lines

Regards

--
Julian Anastasov <[email protected]>

Signature · 6 lines
Arne 'zal' Hueggenberg <[email protected]>


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/