Skip to contentSkip to conversation

ip alias and ipchains

LARTC Javier Miguel Rodriguez 2 participants 2 messages Jan 13, 2002 – Jan 14, 2002

lore
Share & tools
lore
#0 lore raw

Hello

I am trying to build a highly available firewall. I am using
ultramonkey (http://ultramonkey.sourceforge.net/) and everything works fine... but I need to do -j MASQ over -i eth0:0 and this does not work. Here is my network setup

Internet<---- Cluster of Firewalls<---> DMZ

	   eth0:0	eth1:0  	
			|
			|
		       LAN

The default gateway of LAN is 192.168.2.125 (eth1:0 on both nodes of cluster, this work greats)

I have a DSL connection to Internet, so I only have a valid IP address I need to do something like

ipchains -A forward -i eth0:0 -j -s LAN/24 -j MASQ

How can I achieve this? I am using kernel 2.2.20+freeswan 1.92 on both nodes.

Thank you in advance and greetings from Seville (Spain)!

Signature · 8 lines
Javier Miguel Rodríguez.	(GUFO)                                              
Miembro del grupo Linux de la Facultad de Informática de Sevilla     -o)
http://talika.fie.us.es/linux                                        /\\
Linux Registered User #145051.                                      _\_V

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
#1 lore raw

What if you did a user defined chain and jumped to it? Something like this:

ipchains -A forward -i eth0:0 -j domorestuff (notice lower case)
.
.
.
ipchains -A domorestuff -s LAN/24 -j MASQ
ipchains -A domorestuff -j LOG
ipchains -A domorestuff -j DROP
.
.
.

So the only way you get to the domorestuff chain is if the other condition is true with your Internet interface.

It's been a while since I used ipchains and so I might be getting my syntax mixed up with iptables.

- Greg

-----Original Message-----
From: Javier Miguel Rodriguez [mailto:[email protected]]
Sent: Sunday, January 13, 2002 8:25 AM
To: [email protected]
Subject: [LARTC] ip alias and ipchains

Hello

I am trying to build a highly available firewall. I am using
ultramonkey (http://ultramonkey.sourceforge.net/) and everything works fine... but I need to do -j MASQ over -i eth0:0 and this does not work. Here is my network setup

Internet<---- Cluster of Firewalls<---> DMZ

	   eth0:0	eth1:0  	
			|
			|
		       LAN

The default gateway of LAN is 192.168.2.125 (eth1:0 on both nodes of cluster, this work greats)

I have a DSL connection to Internet, so I only have a valid IP address I need to do something like

ipchains -A forward -i eth0:0 -j -s LAN/24 -j MASQ

How can I achieve this? I am using kernel 2.2.20+freeswan 1.92 on both nodes.

Thank you in advance and greetings from Seville (Spain)!

Signature · 12 lines
Javier Miguel Rodríguez.	(GUFO)

Miembro del grupo Linux de la Facultad de Informática de Sevilla     -o)
http://talika.fie.us.es/linux                                        /\\
Linux Registered User #145051.                                      _\_V

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/