Skip to contentSkip to conversation

Marks are ignored by classes

LARTC Scott Kaplan 2 participants 2 messages Jan 17, 2002 – Jan 21, 2002

lore
Share & tools
lore
#0 lore raw

Here is how I'm setting up my PRIO:

	# iptables -A PREROUTING -i eth0 -t mangle -p tcp --dport 22 -j
MARK --set-mark 1
	# iptables -A PREROUTING -i eth0 -t mangle -p tcp --sport 22 -j
MARK --set-mark 1
	# iptables -A PREROUTING -i eth0 -t mangle -p tcp '!' --dport 22
-j MARK --set-mark 2
	# iptables -A PREROUTING -i eth0 -t mangle -p tcp '!' --sport 22
-j MARK --set-mark 2
	# tc qdisc del dev eth0 root handle 1:
	# tc qdisc add dev eth0 root handle 1: prio bands 4 priomap 0 1
2 3 3 3 3 3 3 3 3 3 3 3 3 3
	# tc qdisc add dev eth0 parent 1:1 handle 10: sfq
	# tc qdisc add dev eth0 parent 1:2 handle 20: sfq
	# tc qdisc add dev eth0 parent 1:3 handle 30: sfq
	# tc qdisc add dev eth0 parent 1:4 handle 40: sfq
	# tc filter add dev eth0 parent 1: protocol ip prio 3 handle 4
fw classid 1:4
	# tc filter add dev eth0 parent 1: protocol ip prio 3 handle 3
fw classid 1:3
	# tc filter add dev eth0 parent 1: protocol ip prio 3 handle 2
fw classid 1:2
	# tc filter add dev eth0 parent 1: protocol ip prio 3 handle 1
fw classid 1:1

Then I send a few SSH packets. The packets are marked in PREROUTING. But why is everything winding up in 1:4? Also, if anyone knows why I am marking 4 packets, but only 3 packets wind up in the qdisc, that would be appreciated:

[root@boss root]# ./qos status
LAN Queues:
qdisc sfq 40: quantum 1514b
Sent 246 bytes 3 pkts (dropped 0, overlimits 0)

qdisc sfq 30: quantum 1514b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

qdisc sfq 20: quantum 1514b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

qdisc sfq 10: quantum 1514b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

qdisc prio 1: bands 4 priomap 0 1 2 3 3 3 3 3 3 3 3 3 3 3 3 3 Sent 246 bytes 3 pkts (dropped 0, overlimits 0)

IPTables:
Chain PREROUTING (policy ACCEPT 1050K packets, 257M bytes)
pkts bytes target prot opt in out source
destination

    0     0 MARK       tcp  --  eth0   *       0.0.0.0/0
0.0.0.0/0          tcp dpt:22 MARK set 0x1
    2   216 MARK       tcp  --  eth0   *       0.0.0.0/0
0.0.0.0/0          tcp spt:22 MARK set 0x1
    2   216 MARK       tcp  --  eth0   *       0.0.0.0/0
0.0.0.0/0          tcp dpt:!22 MARK set 0x2
    0     0 MARK       tcp  --  eth0   *       0.0.0.0/0

0.0.0.0/0 tcp spt:!22 MARK set 0x2

Chain OUTPUT (policy ACCEPT 50963 packets, 9269K bytes)
pkts bytes target prot opt in out source
destination

Scott Kaplan
Libritas
Suite 1300
180 Grand Avenue
Oakland, CA 94612
(510) 740-7701
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#1 lore raw

hi

Quoted 17 lines

Date: Thu, 17 Jan 2002 15:19:50 -0800
From: "Scott Kaplan" <[email protected]>
To: <[email protected]>
Subject: [LARTC] Marks are ignored by classes

Here is how I'm setting up my PRIO:

        # iptables -A PREROUTING -i eth0 -t mangle -p tcp --dport 22 -j
MARK --set-mark 1
        # iptables -A PREROUTING -i eth0 -t mangle -p tcp --sport 22 -j
MARK --set-mark 1
        # iptables -A PREROUTING -i eth0 -t mangle -p tcp '!' --dport 22
(quoted diff) +0 -2
-j MARK --set-mark 2
        # iptables -A PREROUTING -i eth0 -t mangle -p tcp '!' --sport 22
-j MARK --set-mark 2
        # tc qdisc del dev eth0 root handle 1:
        # tc qdisc add dev eth0 root handle 1: prio bands 4 priomap 0 1
Quoted 1 line

2 3 3 3 3 3 3 3 3 3 3 3 3 3

im not sure what this is inted to as have never tried this... iahve have tried marking & it does shapes--pls c at bottom ...

Quoted 52 lines
        # tc qdisc add dev eth0 parent 1:1 handle 10: sfq
        # tc qdisc add dev eth0 parent 1:2 handle 20: sfq
        # tc qdisc add dev eth0 parent 1:3 handle 30: sfq
        # tc qdisc add dev eth0 parent 1:4 handle 40: sfq
        # tc filter add dev eth0 parent 1: protocol ip prio 3 handle 4
fw classid 1:4
        # tc filter add dev eth0 parent 1: protocol ip prio 3 handle 3
fw classid 1:3
        # tc filter add dev eth0 parent 1: protocol ip prio 3 handle 2
fw classid 1:2
        # tc filter add dev eth0 parent 1: protocol ip prio 3 handle 1
fw classid 1:1

Then I send a few SSH packets. The packets are marked in PREROUTING. But why is everything winding up in 1:4? Also, if anyone knows why I am marking 4 packets, but only 3 packets wind up in the qdisc, that would be appreciated:

[root@boss root]# ./qos status
LAN Queues:
qdisc sfq 40: quantum 1514b
Sent 246 bytes 3 pkts (dropped 0, overlimits 0)

qdisc sfq 30: quantum 1514b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

qdisc sfq 20: quantum 1514b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

qdisc sfq 10: quantum 1514b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

qdisc prio 1: bands 4 priomap 0 1 2 3 3 3 3 3 3 3 3 3 3 3 3 3 Sent 246 bytes 3 pkts (dropped 0, overlimits 0)

IPTables:
Chain PREROUTING (policy ACCEPT 1050K packets, 257M bytes)
pkts bytes target prot opt in out source
destination

    0     0 MARK       tcp  --  eth0   *       0.0.0.0/0
0.0.0.0/0          tcp dpt:22 MARK set 0x1
    2   216 MARK       tcp  --  eth0   *       0.0.0.0/0
0.0.0.0/0          tcp spt:22 MARK set 0x1
    2   216 MARK       tcp  --  eth0   *       0.0.0.0/0
0.0.0.0/0          tcp dpt:!22 MARK set 0x2
    0     0 MARK       tcp  --  eth0   *       0.0.0.0/0

0.0.0.0/0 tcp spt:!22 MARK set 0x2

Chain OUTPUT (policy ACCEPT 50963 packets, 9269K bytes)
pkts bytes target prot opt in out source
destination

Quoted 6 lines

Scott Kaplan
Libritas
Suite 1300
180 Grand Avenue
Oakland, CA 94612
(510) 740-7701

tc qdisc add dev eth1 root handle 2: cbq bandwidth 1000Kbit svpkt 1000 tc class add dev eth1 parent 2:0 classid 2:1 cbq bandwidth 1000Kbit rate 512Kbit allot 1514 weight 10Kbit prio 5 maxbrust 20 avpkt 1500 bounded tc qdisc add dev eth1 parent 2:1 classid 2:105 est 2sec 10sec cbq bandwidth 512Kbit rate 64Kbit allot 1514 weight 6 Kbit prio 5 maxbrust 10 avpkt 1500 bounded
tc qdisc add dev eth1 parent 2:105 sfq quantum 1514b perturb 10 tc filter add dev eth1 parent 2:0 protocol ip prio 1 handlw 91 fw classid 2:105
.
.
similar for eth0
then..
iptables -t mangle -A PREROUTING -i eth1 -s <clients ips> -d < my lan> -j MARK --set-mark 90
iptables -t mangle -A PREROUTING -i eth0 -s <mylan> -d <clientsips> -j MARK --set-mark 91

& it works...
hope that will be some information for u !!

arindam
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/