Skip to contentSkip to conversation

proxy arp and routing

LARTC David Koski 2 participants 6 messages Feb 1, 2002 – Feb 4, 2002

lore
Share & tools
lore
#0 lore raw

Hello,

Given the network map below, I am able to ping any ip on all networks from the linux box. However, from the cisco router, I cannot ping past eth1 on the linux box. The reverse is also true; I cannot ping past eth0 from a host on LAN. proxy-arp is enabled on the linux box and the route to a.b.c.0/24 is added to the cisco router. I haven't a clue why either way, I can only get to the far side of the linux box but no further.

On second thought, maybe this is not an application for proxy-arp. Your thoughts are appreciated.

    T1 to ISP
        |
        | /30 net
        |
+----------------+
| cisco router   |
+----------------+
        | FastEthernet0/0
        | a.b.c.1/28
        |
 (possible switch/hub here in future)
 (ip range = a.b.c.1-15)
        |
        | a.b.c.2/28
        | eth0
+----------------+
|                |
|           eth1 |---a.b.c.16/24-public-net-----> LAN
|                |   (ip range = a.b.c.16-255)
| linux box      |
|           eth2 |---192.168.1.0/24-- *
|                | * (not revelant to discussion)
+----------------+

David Koski
[email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#1 lore raw

I am not sure what you mean by that but ifconfig shows the correct ip/netmask/broadcast for each ip. Did I miss something?

David

Quoted 13 lines · On Fri, 1 Feb 2002 23:27:28 -0500 "Admin Nplus" <[email protected]> wrote:

did you tell the linux box what ip is where on what side ?

----- Original Message -----
From: "David Koski" <[email protected]>
To: "LARTC" <[email protected]>
Sent: Friday, February 01, 2002 5:41 PM
Subject: [LARTC] proxy arp and routing

Quoted 3 lines

Hello,

Given the network map below, I am able to ping any ip on all networks from

the

Quoted 43 lines
Quoted 1 line

linux box. However, from the cisco router, I cannot ping past eth1 on the

linux

Quoted 1 line

box. The reverse is also true; I cannot ping past eth0 from a host on

LAN.

Quoted 1 line

proxy-arp is enabled on the linux box and the route to a.b.c.0/24 is added

to

Quoted 1 line

the cisco router. I haven't a clue why either way, I can only get to the

far

Quoted 35 lines

side of the linux box but no further.

On second thought, maybe this is not an application for proxy-arp. Your thoughts are appreciated.

    T1 to ISP
        |
        | /30 net
        |
+----------------+
| cisco router   |
+----------------+
        | FastEthernet0/0
        | a.b.c.1/28
        |
 (possible switch/hub here in future)
 (ip range = a.b.c.1-15)
        |
        | a.b.c.2/28
        | eth0
+----------------+
|                |
|           eth1 |---a.b.c.16/24-public-net-----> LAN
|                |   (ip range = a.b.c.16-255)
| linux box      |
|           eth2 |---192.168.1.0/24-- *
|                | * (not revelant to discussion)
+----------------+

David Koski
[email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#2 lore raw
In reply to David Koski
Quoted 6 lines · On Sat, 2 Feb 2002 10:19:13 +0100 Leen Besselink <[email protected]> wrote:
Quoted 3 lines · * David Koski ([email protected]) wrote:

I am not sure what you mean by that but ifconfig shows the correct ip/netmask/broadcast for each ip. Did I miss something?

maybe you could show us the routing table(s) ?
also did you turn on ip forwarding (/proc/sys/net/ipv4/ip_forward) ?

That would be tough because I had to revert back to get it back working. Currently, the public block is routed arround the linux box instead of through it, just to keep it going. But it looked just as I would expect given the ifconfig and /etc/sysconfig/* settings.

I have a howto on an alternate method of proxy arp'ing. It uses identical assignments on eth0 and eth1 instead of using different netmasks. But it uses static routes. Maybe I'll try that. But I would still like to know why the other did not work. Is it possible that with the method I tried, proxy arp is not necessary and only interferes?

David
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#3 lore raw
In reply to David Koski

Sorry, yes. forwarding is enabled.

David

Quoted 73 lines · On Sat, 2 Feb 2002 13:36:23 -0500 "Admin Nplus" <[email protected]> wrote:

does ipforwarding is enabled ?
=1 ?

----- Original Message -----
From: "David Koski" <[email protected]>
To: "LARTC" <[email protected]>
Sent: Saturday, February 02, 2002 12:13 AM
Subject: Re: [LARTC] proxy arp and routing

Quoted 20 lines

I am not sure what you mean by that but ifconfig shows the correct ip/netmask/broadcast for each ip. Did I miss something?

David

Quoted 12 lines · On Fri, 1 Feb 2002 23:27:28 -0500 "Admin Nplus" <[email protected]> wrote:

did you tell the linux box what ip is where on what side ?

----- Original Message -----
From: "David Koski" <[email protected]>
To: "LARTC" <[email protected]>
Sent: Friday, February 01, 2002 5:41 PM
Subject: [LARTC] proxy arp and routing

Quoted 3 lines

Hello,

Given the network map below, I am able to ping any ip on all networks

from

Quoted 2 lines
Quoted 2 lines

the

Quoted 1 line

linux box. However, from the cisco router, I cannot ping past eth1 on

the

Quoted 4 lines
Quoted 4 lines

linux

Quoted 1 line

box. The reverse is also true; I cannot ping past eth0 from a host on

LAN.

Quoted 1 line

proxy-arp is enabled on the linux box and the route to a.b.c.0/24 is

added

Quoted 2 lines
Quoted 2 lines

to

Quoted 1 line

the cisco router. I haven't a clue why either way, I can only get to

the

Quoted 4 lines
Quoted 4 lines

far

Quoted 3 lines

side of the linux box but no further.

On second thought, maybe this is not an application for proxy-arp.

Your

Quoted 26 lines
Quoted 26 lines
Quoted 26 lines

thoughts are appreciated.

    T1 to ISP
        |
        | /30 net
        |
+----------------+
| cisco router   |
+----------------+
        | FastEthernet0/0
        | a.b.c.1/28
        |
 (possible switch/hub here in future)
 (ip range = a.b.c.1-15)
        |
        | a.b.c.2/28
        | eth0
+----------------+
|                |
|           eth1 |---a.b.c.16/24-public-net-----> LAN
|                |   (ip range = a.b.c.16-255)
| linux box      |
|           eth2 |---192.168.1.0/24-- *
|                | * (not revelant to discussion)
+----------------+
Quoted 11 lines
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines

David Koski
[email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:

http://ds9a.nl/lartc/

Quoted 5 lines
Quoted 1 line
Quoted 1 line

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/

#4 lore raw
In reply to David Koski
Quoted 6 lines · David Koski

Given the network map below, I am able to ping any ip on all networks from the linux box. However, from the cisco router, I cannot ping past eth1 on the linux box. The reverse is also true; I cannot ping past eth0 from a host on LAN. proxy-arp is enabled on the linux box and the route to a.b.c.0/24 is added to the cisco router. I haven't a clue why either way, I can only get to the far side of the linux box but no further.

I do not care about your ascii art, just about the following:
ip route show /proc/sys/net/ipv4/conf/eth[012]/proxy_arp /proc/sys/net/ipv4/conf/eth[012]/rp_filter /proc/sys/net/ipv4/ip_forward
1) proxy_arp must be set to 1
2) rp_filter: you might start with 0
3) ip_forward should be set to 1
4) all routes must be sane:
ip route add a.b.c.0/28 dev eth0
ip route add a.b.c.0/24 dev eth1
ip route add 192.168.1.0 dev eth2
ip route add default via a.b.c.1

Then you should be able to arp-ping the whole world from anywhere inside your network.

Signature · 7 lines
<[email protected]> Telegraaf Elektronische Media  http://wwwijzer.nl
http://leerquoten.monster.org/ http://www.faqs.org/rfcs/rfc1855.html 
Let your government know you value your freedom. Sign the petition:
http://petition.eurolinux.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
#5 lore raw
In reply to David Koski
Quoted 2 lines · On Mon, 4 Feb 2002 15:59:44 +0100 Ard van Breemen <[email protected]> wrote:
Quoted 1 line · David Koski

Given the network map below, I am able to ping any ip on all networks from

the

Quoted 1 line
Quoted 1 line

linux box. However, from the cisco router, I cannot ping past eth1 on the

linux

Quoted 2 lines
Quoted 2 lines

box. The reverse is also true; I cannot ping past eth0 from a host on LAN. proxy-arp is enabled on the linux box and the route to a.b.c.0/24 is added

to

Quoted 1 line
Quoted 1 line

the cisco router. I haven't a clue why either way, I can only get to the

far

Quoted 16 lines
Quoted 1 line

side of the linux box but no further.

I do not care about your ascii art, just about the following:
ip route show /proc/sys/net/ipv4/conf/eth[012]/proxy_arp /proc/sys/net/ipv4/conf/eth[012]/rp_filter /proc/sys/net/ipv4/ip_forward
1) proxy_arp must be set to 1
2) rp_filter: you might start with 0
3) ip_forward should be set to 1
4) all routes must be sane:
ip route add a.b.c.0/28 dev eth0
ip route add a.b.c.0/24 dev eth1
ip route add 192.168.1.0 dev eth2
ip route add default via a.b.c.1

Quoted 2 lines

Then you should be able to arp-ping the whole world from anywhere inside your network.

You did not mention:

/proc/sys/net/ipv4/conf/eth[012]/forwarding

It is set to 1 also. The only difference I have with your settings above is rp_filter. I'll change it to 0 and see what happens. Since the settings were reverted back and I don't have access to it right now, I cannot dump the routing table. But it was verified to be correct and consistant with the above settings.

Thank you,
David Koski
[email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/