Perl script to adjust default routing on 2 Net connections
Using a stock implementation of Christoph's and Julian's setup for connecting to two lines (DSL from different ISPs in my case) I ran into situations where a gateway was still up, but the ISP had systems down beyond it. To deal with that, I've put together a perl script that I run from cron. I have this running in production, but only for a few days, so it's not thoroughly tested yet. Still, I'll include it here in case either it's useful to someone, or someone has suggestions on how to improve it.
It should also be adaptable to similar setups, although if you're not using Julian's patches you should search and replace "proto static" with nothing first (not even sure it's doing any good in this context anyway, but not sure it isn't).
Run it from the prompt to test before adding to cron.
Whit
--- cut ---
#!/usr/local/bin/perl
# checkroutes.pl version 0.04, 6 Feb. 2002, [email protected] # Extends stock Nano-Howto setup with upstream route accessibility checking # See http://www.linuxvirtualserver.org/~julian/nano.txt and patches at # http://www.linuxvirtualserver.org/~julian/#routes # (if not using Julian's patchs, remove "proto static" occurrences below)
# Run from cron (set with "crontab -e")
# example: "0-59/2 * * * * /path/to/checkroutes.pl" runs this every 2 minutes
# Best IPs to test may be last IPs at ISP before routing out to Net
# If perl not at /usr/local/bin/perl change first line to point to it
# Before running install Net::Ping from http://freeware.roobik.com/netping/
# (untar, cd to directory, "perl Makefile.PL; make; make install")
use Net::Ping;
# User settings
# _____________
$ip = "/usr/sbin/ip"; # Location of "ip" on system
$gw1 = ""; # Gateway 1 IP
$dev1 = ""; # Device (e.g., eth1)
$tip1 = ""; # Upstream IP to test
$src1 = ""; # Source address for outgoing packets
$wei1 = "1"; # Weight
$gw2 = ""; # Gateway 2 IP
$dev2 = ""; # Device (e.g., eth2)
$tip2 = ""; # Upstream IP to test
$src2 = ""; # Source address for outgoing packets
$wei2 = "1"; # Weight
$tab = "222"; # Table to set routes in
$logfile = "/var/log/checkroutes.log"; # File to log messages to
# create timestamp for log # ________________________
sub TimeStamp {
# subroutine to create a "nice" looking timestamp # that doesn't rely on the system's 'date' command
my @days = ('Sun','Mon','Tue','Wed','Thu','Fri','Sat');
my @months = ('Jan','Feb','Mar','Apr','May','Jun','Jul','Aug','Sep',
'Oct','Nov','Dec');
my ($sec,$min,$hour,$dom,$mon,$year,$wday,$yday,$isd) = localtime(time);
my $timestamp = sprintf("%3s %3s %02d %4d %02d:%02d:%02d", $days[$wday],
$months[$mon], $dom, $year+1900, $hour, $min, $sec);
return $timestamp;
} # be sure routes are set via appropriate gateways to test IPs # ___________________________________________________________
$checkro = $ip ro ls;
if (!($checkro =~ /$tip1/)) {
system ("$ip ro add to $tip1 via $gw1 src $src1 proto static")
|| die ("failure adding route\n");
}
if (!($checkro =~ /$tip2/)) {
system ("$ip ro add to $tip2 via $gw2 src $src2 proto static")
|| die ("failure adding route\n");
}# test if $gw1 and/or $gw2 currently in table $tab # ________________________________________________
$checkgw = qx/$ip ro ls tab $tab/;
if ($checkgw =~ /$gw1/) {
$check1 = 1;
} else {
$check1 = 0;
}if ($checkgw =~ /$gw2/) {
$check2 = 1;
} else {
$check2 = 0;
}# ping the test IPs $tip1 and $tip2 # _________________________________
$p = Net::Ping->new("icmp");
if ($p->ping($tip1)) {
$live1 = 1;
} else {
$live1 = 0;
}
$p->close();
$p = Net::Ping->new("icmp");
if ($p->ping($tip2)) {
$live2 = 1;
} else {
$live2 = 0;
}$p->close();
# If the current default in table $tab does not match the ping results then
# if only one route's test IP is pingable change the default to that route # or if both test IPs are pingable change the default to use both # or if neither test IPs are pingable change the default to use both # (might as well continue to try them, if we're not going anywhere anyway) # _________________________________________________________________________
if (($check1 != $live1)||($check2 != $live2)) {
if ((($live1 = 1)&&($live2 = 1))||(($live1 = 0)&&($live2 = 0))) {
system ("$ip ro ap default tab $tab proto static nexthop via $gw1 dev $dev1 weight $wei1 nexthop via $gw2 dev $dev2 weight $wei2")
|| die ("failure appending route\n");
} elsif (($live1 = 1)&&($live2 = 0)) {
system ("$ip ro ap default tab $tab proto static via $gw1 dev $dev1")
|| die ("failure appending route\n");
} elsif (($live1 = 0)&&($live2 = 1)) {
system ("$ip ro ap default tab $tab proto static via $gw2 dev $dev2")
|| die ("failure appending route\n");
} else {
die ("value out of bounds\n");
}
system ("$ip ro del default tab $tab")
|| die ("failure deleting default route\n");
system ("$ip ro flush cache")
|| die ("failure flushing cache\n");
}# log # ___
if (($live1 = 1)&&($live2 = 1)) {
$log = "both UP";
} elsif (($live1 = 0)&&($live2 = 0)) {
$log = "both DOWN (set UP)";
} elsif (($live1 = 1)&&($live2 = 0)) {
$log = "$gw1 up, $gw2 DOWN";
} elsif (($live1 = 0)&&($live2 = 1)) {
$log = "$gw2 up, $gw1 DOWN";
}open(LOG, ">>$logfile");
print LOG &TimeStamp . " - $log\n";
close(LOG);
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Slightly updated - the "die" error catchers didn't always do what I expected, so gone for now. Otherwise this has been behaving well.
Whit
--- cut ---
#!/usr/local/bin/perl
# checkroutes.pl version 0.05, 18 Feb. 2002, [email protected] # changed from 0.04: (1) removed disfunctional "die" statements # (2) added double check that for extra "default"
# Extends stock Nano-Howto setup with upstream route accessibility checking # See http://www.linuxvirtualserver.org/~julian/nano.txt and patches at # http://www.linuxvirtualserver.org/~julian/#routes
# (if not using Julian's patchs, remove "proto static" occurrences below)
# Run from cron (set with "crontab -e")
# example: "0-59/2 * * * * /path/to/checkroutes.pl" runs this every 2 minutes
# Best IPs to test may be last IPs at ISP before routing out to Net
# If perl not at /usr/local/bin/perl change first line to point to it
# Before running install Net::Ping from http://freeware.roobik.com/netping/
# (untar, cd to directory, "perl Makefile.PL; make; make install")
use Net::Ping;
# User settings
# _____________
$ip = "/usr/sbin/ip"; # Location of "ip" on system
$gw1 = ""; # Gateway 1 IP
$dev1 = ""; # Device (e.g., eth1)
$tip1 = ""; # Upstream IP to test
$src1 = ""; # Source address for outgoing packets
$wei1 = ""; # Weight
$gw2 = ""; # Gateway 2 IP
$dev2 = ""; # Device (e.g., eth2)
$tip2 = ""; # Upstream IP to test
$src2 = ""; # Source address for outgoing packets
$wei2 = ""; # Weight
$tab = "222"; # Table to set routes in
$logfile = "/var/log/checkroutes.log"; # File to log messages to
# create timestamp for log # ________________________
sub TimeStamp {
# subroutine to create a "nice" looking timestamp # that doesn't rely on the system's 'date' command
my @days = ('Sun','Mon','Tue','Wed','Thu','Fri','Sat');
my @months = ('Jan','Feb','Mar','Apr','May','Jun','Jul','Aug','Sep',
'Oct','Nov','Dec');
my ($sec,$min,$hour,$dom,$mon,$year,$wday,$yday,$isd) = localtime(time);
my $timestamp = sprintf("%3s %3s %02d %4d %02d:%02d:%02d", $days[$wday],
$months[$mon], $dom, $year+1900, $hour, $min, $sec);
return $timestamp;
} # be sure routes are set via appropriate gateways to test IPs # ___________________________________________________________
$checkro = $ip ro ls;
if (!($checkro =~ /$tip1/)) {
system ("$ip ro add to $tip1 via $gw1 src $src1 proto static");
}
if (!($checkro =~ /$tip2/)) {
system ("$ip ro add to $tip2 via $gw2 src $src2 proto static");
}# test if $gw1 and/or $gw2 currently in table $tab # ________________________________________________
$checkgw = qx/$ip ro ls tab $tab/;
if ($checkgw =~ /$gw1/) {
$check1 = 1;
} else {
$check1 = 0;
}if ($checkgw =~ /$gw2/) {
$check2 = 1;
} else {
$check2 = 0;
}# ping the test IPs $tip1 and $tip2 # _________________________________
$p = Net::Ping->new("icmp");
if ($p->ping($tip1)) {
$live1 = 1;
} else {
$live1 = 0;
}
$p->close();
$p = Net::Ping->new("icmp");
if ($p->ping($tip2)) {
$live2 = 1;
} else {
$live2 = 0;
}$p->close();
# If the current default in table $tab does not match the ping results then
# if only one route's test IP is pingable change the default to that route # or if both test IPs are pingable change the default to use both # or if neither test IPs are pingable change the default to use both # (might as well continue to try them, if we're not going anywhere anyway) # _________________________________________________________________________
if (($check1 != $live1)||($check2 != $live2)) {
if ((($live1 = 1)&&($live2 = 1))||(($live1 = 0)&&($live2 = 0))) {
system ("$ip ro ap default tab $tab proto static nexthop via $gw1 dev $dev1 weight $wei1 nexthop via $gw2 dev $dev2 weight $wei2");
} elsif (($live1 = 1)&&($live2 = 0)) {
system ("$ip ro ap default tab $tab proto static via $gw1 dev $dev1");
} elsif (($live1 = 0)&&($live2 = 1)) {
system ("$ip ro ap default tab $tab proto static via $gw2 dev $dev2");
} else {
die ("value out of bounds\n");
}
system ("$ip ro del default tab $tab");
system ("$ip ro flush cache");
}# log # ___
if (($live1 = 1)&&($live2 = 1)) {
$log = "both UP";
} elsif (($live1 = 0)&&($live2 = 0)) {
$log = "both DOWN (set UP)";
} elsif (($live1 = 1)&&($live2 = 0)) {
$log = "$gw1 up, $gw2 DOWN";
} elsif (($live1 = 0)&&($live2 = 1)) {
$log = "$gw2 up, $gw1 DOWN";
}open(LOG, ">>$logfile");
print LOG &TimeStamp . " - $log\n";
close(LOG);
# double check that only one default is set # _________________________________________
$checkdup = qx/$ip ro ls tab $tab/;
if ($checkdup =~ /default.*default/s) {
system ("$ip ro del default tab $tab");
}_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
More fixed. Simpler logic on appending. Deletes only if append has worked. An allows setting the number of pings to try and the number of those that must be good.
Whit
--- cut ---
#!/usr/local/bin/perl
# checkroutes.pl version 0.06, 18 Feb. 2002, [email protected] # Extends stock Nano-Howto setup with upstream route accessibility checking # See http://www.linuxvirtualserver.org/~julian/nano.txt and patches at # http://www.linuxvirtualserver.org/~julian/#routes # (if not using Julian's patchs, remove "proto static" occurrences below)
# Run from cron (set with "crontab -e")
# example: "0-59/2 * * * * /path/to/checkroutes.pl" runs this every 2 minutes
# Best IPs to test for general use may be last IPs at ISPs before routing out to Net # Best IP to test if a single remote site is most important is that site's
# If perl not at /usr/local/bin/perl change first line to point to it
# Before running install Net::Ping from http://freeware.roobik.com/netping/
# (untar, cd to directory, "perl Makefile.PL; make; make install")
use Net::Ping;
# User settings
# _____________
$ip = "/usr/sbin/ip"; # Location of "ip" on system
$gw1 = ""; # Gateway 1 IP
$dev1 = ""; # Device (e.g., eth1)
$tip1 = ""; # Upstream IP to test
$src1 = ""; # Source address for outgoing packets
$wei1 = "1"; # Weight
$gw2 = ""; # Gateway 2 IP
$dev2 = ""; # Device (e.g., eth2)
$tip2 = ""; # Upstream IP to test
$src2 = ""; # Source address for outgoing packets
$wei2 = "1"; # Weight
$pings = "1"; # Number of pings to send
$good = "1"; # Number of pings that must be good
$tab = "222"; # Table to set routes in
$logfile = "/var/log/checkroutes.log"; # File to log messages to
# create timestamp for log # ________________________
sub TimeStamp {
# subroutine to create a "nice" looking timestamp # that doesn't rely on the system's 'date' command
my @days = ('Sun','Mon','Tue','Wed','Thu','Fri','Sat');
my @months = ('Jan','Feb','Mar','Apr','May','Jun','Jul','Aug','Sep',
'Oct','Nov','Dec');
my ($sec,$min,$hour,$dom,$mon,$year,$wday,$yday,$isd) = localtime(time);
my $timestamp = sprintf("%3s %3s %02d %4d %02d:%02d:%02d", $days[$wday],
$months[$mon], $dom, $year+1900, $hour, $min, $sec);
return $timestamp;
} # be sure routes are set via appropriate gateways to test IPs # ___________________________________________________________
$checkro = $ip ro ls;
if (!($checkro =~ /$tip1/)) {
system ("$ip ro add to $tip1 via $gw1 src $src1 proto static");
}
if (!($checkro =~ /$tip2/)) {
system ("$ip ro add to $tip2 via $gw2 src $src2 proto static");
}# test if $gw1 and/or $gw2 currently in table $tab # ________________________________________________
$checkgw = qx/$ip ro ls tab $tab/;
if ($checkgw =~ /$gw1/) {
$check1 = 1;
} else {
$check1 = 0;
}if ($checkgw =~ /$gw2/) {
$check2 = 1;
} else {
$check2 = 0;
}# ping the test IPs $tip1 and $tip2 # _________________________________
$i=0;
$p = Net::Ping->new("icmp");
while ($i < $pings) {
if ($p->ping($tip1)) {
$ping1++;
}
$i++;
}$p->close();
if ($ping1 >= $good) {
$live1 = 1;
} else {
$live1 = 0;
}$i=0;
$p = Net::Ping->new("icmp");
while ($i < $pings) {
if ($p->ping($tip2)) {
$ping2++;
}
$i++;
}$p->close();
if ($ping2 >= $good) {
$live2 = 1;
} else {
$live2 = 0;
}# If the current default in table $tab does not match the ping results then
# if only one route's test IP is pingable change the default to that route # or if both test IPs are pingable change the default to use both # or if neither test IPs are pingable change the default to use both # (might as well continue to try them, if we're not going anywhere anyway) # _________________________________________________________________________
# append new default route # ________________________
if (($check1 != $live1)||($check2 != $live2)) {
if (($live1 = 1)&&($live2 = 0)) {
system ("$ip ro ap default tab $tab proto static via $gw1 dev $dev1");
} elsif (($live1 = 0)&&($live2 = 1)) {
system ("$ip ro ap default tab $tab proto static via $gw2 dev $dev2");
} else {
system ("$ip ro ap default tab $tab proto static nexthop via $gw1 dev $dev1 weight $wei1 nexthop via $gw2 dev $dev2 weight $wei2");
}
}# delete and flush old default route if second has been appended # ______________________________________________________________
$checkdup = qx/$ip ro ls tab $tab/;
if ($checkdup =~ /default.*default/s) {
system ("$ip ro del default tab $tab");
system ("$ip ro flush cache");
}# log # ___
if (($live1 = 1)&&($live2 = 1)) {
$log = "both UP";
} elsif (($live1 = 0)&&($live2 = 0)) {
$log = "both DOWN (set UP)";
} elsif (($live1 = 1)&&($live2 = 0)) {
$log = "$gw1 up, $gw2 DOWN";
} elsif (($live1 = 0)&&($live2 = 1)) {
$log = "$gw2 up, $gw1 DOWN";
}open(LOG, ">>$logfile");
print LOG &TimeStamp . " - $log\n";
close(LOG);
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
Quoted 3 lines · Whit Blauvelt
More fixed. Simpler logic on appending. Deletes only if append has worked. An allows setting the number of pings to try and the number of those that must be good.
Do you have a URL for this script? I want to add it to the HOWTO but want to retain your ability to edit it without going through me.
Regards,
bert
Signature · 6 lines
http://www.PowerDNS.com Versatile DNS Software & Services http://www.tk the dot in .tk http://lartc.org Linux Advanced Routing & Traffic Control HOWTO _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/