Load Balance RX/TX data on the same NICs.
Hello,
I have a Compaq Proliant i850R, running RedHat 7.1. There are 3 NICs attached to it, 2 eepro100, and 1 ThunderLAN driver v1.14a.
This box is being prepped to be a download server.
GOAL:
Requests are sent to each NIC via seperate IP addresses. All 3 are on the same subnet.
All requests are load balanced via a DNS server. We want all requests to exit the same NIC that they entered.
PROBLEM:
All requests are satisfied via the last NIC (eth2). eth2 does 99% of the transmissions.
With the configuration below it is possible to do load-balancing, both in and out, but it is not possible to secure shell to the box. If the "ip rule" lines are commented out, login is possible, but no outbound load balancing.
OUR CONFIGURATION:
ip route add 206.17.228.231 dev eth1
ip route add 206.17.228.232 dev eth2
ip route add 206.17.228.230 dev eth0/sbin/route del default 2> /dev/null/sbin/ip route add default equalize nexthop via 206.17.228.2 dev eth1 nexthop via 206.17.228.2 dev eth2
ip route add 206.17.228.231 dev eth1 table 231
ip route add default via 206.17.228.2 dev eth1 src 206.17.228.231 table 231 ip route flush cache
ip route add 206.17.228.232 dev eth2 table 232
ip route add default via 206.17.228.2 dev eth1 src 206.17.228.232 table 232 ip route flush cache
ip route add 206.17.228.230 dev eth0 table 230
ip route add default via 206.17.228.2 dev eth1 src 206.17.228.230 table 230 ip route flush cache
ip rule add from 206.17.228.231 table 231
ip rule add from 206.17.228.232 table 232
ip rule add from 206.17.228.230 table 230
WHAT AM I DOING WRONG?
Robert Richardson
You might look at http://www.linuxvirtualserver.org/~julian/nano.txt - if your not using the patches referred to there it's still a good outline of a solution that should generalize to your setup. Just leave out "proto static" in the lines where it occurs and set 3 rather than 2 special tables. I have no trouble with either SSH or having FTP return over the interface it comes in on with that setup.
Whit
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/
This page looks promising.
I appreciate your suggestion.
Thanks,
Robert.
-----Original Message-----
From: Whit Blauvelt [mailto:[email protected]]
Sent: Thursday, February 07, 2002 4:17 PM
To: Richardson, Robert
Cc: '[email protected]'
Subject: Re: [LARTC] Load Balance RX/TX data on the same NICs.
You might look at http://www.linuxvirtualserver.org/~julian/nano.txt - if your not using the patches referred to there it's still a good outline of a solution that should generalize to your setup. Just leave out "proto static" in the lines where it occurs and set 3 rather than 2 special tables. I have no trouble with either SSH or having FTP return over the interface it comes in on with that setup.
Whit
Quoted 4 lines · Robert
With the configuration below it is possible to do load-balancing, both in and out, but it is not possible to secure shell to the box. If the "ip rule" lines are commented out, login is possible, but no outbound load balancing.
Please be more precise. What happens when connecting via ssh? Run ssh -v. Do you get a timeout? Do you get a connection reset by peer? At which line does it stop working. My glass ball is running overtime on this list.
Can you run tcpdump on all interfaces on your Compaq while you try to login?
Quoted 7 lines
OUR CONFIGURATION:
ip route add 206.17.228.231 dev eth1
ip route add 206.17.228.232 dev eth2
ip route add 206.17.228.230 dev eth0/sbin/routedel default 2>/dev/null/sbin/iproute add default equalize nexthop via 206.17.228.2 dev eth1 nexthop via 206.17.228.2 dev eth2
I suggest you remove the generic default route - you've covered all possibilities in other tables - unless there are more IP addresses on your machine.
In that case, the problem is that ssh changes its TOS halfway during connecting, causing packets that previously went out over, say eth0, to suddenly go out over eth1, which may upset your local routing. Try ssh-ing to one of the addresses for which a table exists.
Anyway, do the measurements. This setup is supposed to work just fine.
Regards,
bert
Signature · 7 lines
http://www.PowerDNS.com Versatile DNS Software & Services http://www.tk the dot in .tk Netherlabs BV / Rent-a-Nerd.nl - Nerd Available - Linux Advanced Routing & Traffic Control: http://ds9a.nl/lartc _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://ds9a.nl/lartc/