Skip to contentSkip to conversation

few doubts about the working of tc

LARTC Stef Coene 3 participants 5 messages Jan 3, 1980 – Mar 26, 2002

lore
Share & tools
lore

Stef Coene

author
#0 lore raw
Quoted 32 lines · Akarapu Mahesh

HI stef,
The following is the test scenario i am using.

A--->B--->C

First let me explain what i am doing here. I want to rate limit the traffic between A and B dynamically. I am doing this on A using "tc". All these machines have redhat 7.1 and A has 2.2.13 kernel with diffserv patch and B and C have 2.4.3 kernels.The following is the script that i am using.

1)tc qdisc del dev eth1 root
2)tc qdisc add dev eth1 root handle 1: cbq bandwidth 100Mbit cell 8 avpkt 1000 mpu 64
3)tc class add dev eth1 parent 1:0 classid 1:1 cbq bandwidth 100Mbit rate 100Mbit allot 1514 cell 8 weight 10Mbit prio 8 maxburst 20 avpkt 1000 4)tc class add dev eth1 parent 1:1 classid 1:2 cbq bandwidth 100Mbit rate 60Mbit allot 1514 cell 8 weight 6Mbit prio 3 maxburst 20 avpkt 1000 bounded 5)sudo tc class add dev eth1 parent 1:1 classid 1:3 cbq bandwidth 100Mbit rate 40Mbit allot 1514 cell 8 weight 4Mbit prio 7 maxburst 20 avpkt 1000 bounded
6)tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 match ip dst 192.168.123.5 flowid 1:2

SInce i want to limit only the traffic between A and C i created only one filter for class 1:2. NOw i am changing the bandwidth limit using the following command. In the above 192.168.123.5 is the address of C.

7)tc class change dev eth1 parent 1:1 classid 1:2 cbq bandwidth 100Mbit rate 60Mbit allot 1514 cell 8 weight 6Mbit prio 3 maxburst 20 avpkt 1000 bounded

Quoted 6 lines

Now let me tell my doubts.

1)Now suppose the bandwidth limit of A-->C traffic is changed from 60Mbps to 20Mbps during a transfer, how does tc react to it?? Does it send the packets remaining in the queue at 60Mbps or 20Mbps or does it drop all the packets before changing the limit to 20Mbps??

I don't know what happens if you use the change command. :(. It will change the bandwidth, but I don't know what happens with the queue.

Quoted 1 line

2) Can i run the same script on B to limit the taffic between A and C??

Yes

Stef

Signature · 7 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw

HI,
I am new to tc. I have a few basic doubts about the working of tc.I am trying to limit the bandwidth between two linux machines to 12Mbps. I am using the route filter to achieve this. I tested with ttcp traffic between these machines. I used tcpdump cature the data during this transfer and observed this using tcptrace. I find that the throuhgput was much higher than 12Mbp sometimes during the transfer. But the avg throughput for the whole transfer was 12Mbps. NOw my doubt is how tc is going to limit the bandwidth?? Please let me know how exactly tc limits the bandwidth.

thanks
mahesh

_________________________________________________________________
Join the world’s largest e-mail service with MSN Hotmail.
http://www.hotmail.com

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

author
#2 lore raw
In reply to Stef Coene
Quoted 9 lines · Akarapu Mahesh

HI,
I am new to tc. I have a few basic doubts about the working of tc.I am trying to limit the bandwidth between two linux machines to 12Mbps. I am using the route filter to achieve this. I tested with ttcp traffic between these machines. I used tcpdump cature the data during this transfer and observed this using tcptrace. I find that the throuhgput was much higher than 12Mbp sometimes during the transfer. But the avg throughput for the whole transfer was 12Mbps. NOw my doubt is how tc is going to limit the bandwidth?? Please let me know how exactly tc limits the bandwidth.

How do you made your setup ? CBQ or HTB? classes, qdiscs, filters ? More info plz.

Stef

Signature · 7 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#3 lore raw
In reply to Stef Coene

tc doesn't limit the traffic, it is the kernel who does it.

The limitation of the traffic is based on some queue theories. Packets are enqueued in a way, and then dequeued and sent to the netwok interface.

The fact that the throughput is sometime very high can be explained how the queues manage the bursts of datas. We could say it is a feature, not a bug. But if you don't want it, it is a parameter of the queue, that you can change with tc (hehehe, here is the question!) with a parameter like "burst" (it depends of the type of queue).

Quoted 23 lines · Akarapu Mahesh

HI,
I am new to tc. I have a few basic doubts about the working of tc.I am trying to limit the bandwidth between two linux machines to 12Mbps. I am using the route filter to achieve this. I tested with ttcp traffic between these machines. I used tcpdump cature the data during this transfer and observed this using tcptrace. I find that the throuhgput was much higher than 12Mbp sometimes during the transfer. But the avg throughput for the whole transfer was 12Mbps. NOw my doubt is how tc is going to limit the bandwidth?? Please let me know how exactly tc limits the bandwidth.

thanks
mahesh

_________________________________________________________________
Join the world’s largest e-mail service with MSN Hotmail.
http://www.hotmail.com

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Signature · 14 lines
      __o
    _ \<_
   (_)/(_)

Saludos de Julián
EA4ACL
-.-

Foro Wireless Madrid
http://opennetworks.rg3.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#4 lore raw
In reply to Stef Coene

HI stef,
The following is the test scenario i am using.

A--->B--->C

First let me explain what i am doing here. I want to rate limit the traffic between A and B dynamically. I am doing this on A using "tc". All these machines have redhat 7.1 and A has 2.2.13 kernel with diffserv patch and B and C have 2.4.3 kernels.The following is the script that i am using.

1)tc qdisc del dev eth1 root
2)tc qdisc add dev eth1 root handle 1: cbq bandwidth 100Mbit cell 8 avpkt 1000 mpu 64
3)tc class add dev eth1 parent 1:0 classid 1:1 cbq bandwidth 100Mbit rate 100Mbit allot 1514 cell 8 weight 10Mbit prio 8 maxburst 20 avpkt 1000 4)tc class add dev eth1 parent 1:1 classid 1:2 cbq bandwidth 100Mbit rate 60Mbit allot 1514 cell 8 weight 6Mbit prio 3 maxburst 20 avpkt 1000 bounded 5)sudo tc class add dev eth1 parent 1:1 classid 1:3 cbq bandwidth 100Mbit rate 40Mbit allot 1514 cell 8 weight 4Mbit prio 7 maxburst 20 avpkt 1000 bounded
6)tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 match ip dst 192.168.123.5 flowid 1:2

SInce i want to limit only the traffic between A and C i created only one filter for class 1:2. NOw i am changing the bandwidth limit using the following command. In the above 192.168.123.5 is the address of C.

7)tc class change dev eth1 parent 1:1 classid 1:2 cbq bandwidth 100Mbit rate 60Mbit allot 1514 cell 8 weight 6Mbit prio 3 maxburst 20 avpkt 1000 bounded

Now let me tell my doubts.

1)Now suppose the bandwidth limit of A-->C traffic is changed from 60Mbps to 20Mbps during a transfer, how does tc react to it?? Does it send the packets remaining in the queue at 60Mbps or 20Mbps or does it drop all the packets before changing the limit to 20Mbps??

2) Can i run the same script on B to limit the taffic between A and C??

thanks
mahesh

Quoted 19 lines

From: Stef Coene <[email protected]>
To: "Akarapu Mahesh" <[email protected]>, [email protected]
Subject: Re: [LARTC] few doubts about the working of tc
Date: Mon, 25 Mar 2002 18:51:33 +0100

Quoted 4 lines · Akarapu Mahesh

HI,
I am new to tc. I have a few basic doubts about the working of tc.I am trying to limit the bandwidth between two linux machines to 12Mbps. I am using the route filter to achieve this. I tested with ttcp traffic

between

Quoted 5 lines

these machines. I used tcpdump cature the data during this transfer and observed this using tcptrace. I find that the throuhgput was much higher than 12Mbp sometimes during the transfer. But the avg throughput for the whole transfer was 12Mbps. NOw my doubt is how tc is going to limit the bandwidth?? Please let me know how exactly tc limits the bandwidth.

How do you made your setup ? CBQ or HTB? classes, qdiscs, filters ? More info plz.

Quoted 8 lines

Stef

--

[email protected]
"Using Linux as bandwidth manager"
http://www.docum.org/
#lartc @ irc.openprojects.net

_________________________________________________________________
MSN Photos is the easiest way to share and print your photos:
http://photos.msn.com/support/worldwide.aspx

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/