Skip to contentSkip to conversation

Shaping

LARTC Isak Badenhorst 4 participants 5 messages Apr 22, 2002 – Jun 1, 2004

lore
Share & tools
lore
#0 lore raw

Hi all

I am trying to shape the e-mail going out on my network. When i send some outgoing mail it just eats up all bandwidth available. I would appreciate some help. I have a 128kbit link to my provider.

tc qdisc add dev eth0 root handle 10: cbq bandwidth 10mbit avpkt 1000 tc class add dev eth0 parent 10:0 classid 10:2 cbq bandwidth 10mbit rate 128kbit allot 1514 maxburst 20 avpkt 1000 isolated bounded prio 3 tc qdisc add dev eth0 parent 10:2 handle 20: cbq bandwidth 128kbit allot 1514 avpkt 1000
tc class add dev eth0 parent 20: classid 20:10 cbq bandwidth 128kbit rate 16kbit weight 4 allot 1514 maxburst 20 avpkt 1000
tc class add dev eth0 parent 20: classid 20:20 cbq bandwidth 128kbit rate 112kbit weight 12 allot 1514 maxburst 20 avpkt 1000

tc filter add dev eth0 parent 10: protocol ip prio 3 u32 match ip src 0.0.0.0/32 flowid 10:2
tc filter add dev eth0 parent 20: protocol ip prio 3 u32 match ip dport 25 0xffff flowid 20:10
tc filter add dev eth0 parent 20: protocol ip prio 3 u32 match ip src 0.0.0.0/32 flowid 20:20

Any help would be appreciated.

Thanks

Isak

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 17 lines · Isak Badenhorst

Hi all

I am trying to shape the e-mail going out on my network. When i send some outgoing mail it just eats up all bandwidth available. I would appreciate some help. I have a 128kbit link to my provider.

tc qdisc add dev eth0 root handle 10: cbq bandwidth 10mbit avpkt 1000 tc class add dev eth0 parent 10:0 classid 10:2 cbq bandwidth 10mbit rate 128kbit allot 1514 maxburst 20 avpkt 1000 isolated bounded prio 3 tc qdisc add dev eth0 parent 10:2 handle 20: cbq bandwidth 128kbit allot 1514 avpkt 1000
tc class add dev eth0 parent 20: classid 20:10 cbq bandwidth 128kbit rate 16kbit weight 4 allot 1514 maxburst 20 avpkt 1000
tc class add dev eth0 parent 20: classid 20:20 cbq bandwidth 128kbit rate 112kbit weight 12 allot 1514 maxburst 20 avpkt 1000

Quoted 8 lines

tc filter add dev eth0 parent 10: protocol ip prio 3 u32 match ip src 0.0.0.0/32 flowid 10:2
tc filter add dev eth0 parent 20: protocol ip prio 3 u32 match ip dport 25 0xffff flowid 20:10
tc filter add dev eth0 parent 20: protocol ip prio 3 u32 match ip src 0.0.0.0/32 flowid 20:20

Any help would be appreciated.

I suppose the setup is not working ? :)
Change 128kbit in 120kbit. Rule 1 for shaping : "Make sure YOU are the bottleneck".

Stef

Quoted 8 lines

Thanks

Isak

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Signature · 7 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw

[LARTC] shaping

In reply to Isak Badenhorst

Hi!

Is there any way to do just plain vanilla TBF (Token Buck Filter) type shaping on a group of ips/networks, not an entire interface.

Currently the only way I know how to shape in Linux is to use HTB or CBQ, but both of these need a total rate and then you need to subdivide that into classes. That is not what I want. All I want is Cisco generic traffic shaping style shaping (or similar to how the old shaper module worked), iow I don't want to specify how much bandwidth I have, I just want to make sure that any particular group never exceeds a given rate.

Signature · 16 lines
Regards
 Abraham

TODAY the Pond!
TOMORROW the World!
                -- Frogs (1972)

___________________________________________________
 Abraham vd Merwe - Frogfoot Networks CC
 1st Floor, Albion Springs, 183 Main Road, Newlands
 Phone: +27 21 689 3873 Cell: +27 82 565 4451
 Http: http://www.frogfoot.net/ Email: [email protected]

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#3 lore raw

RE: [LARTC] shaping

In reply to Isak Badenhorst

Not the answer you're looking for, but why not just specify your total bandwidth being much larger than your interface actually is and then subdividing into your groups?

Mike.

Quoted 6 lines

-----Original Message-----
From: Abraham van der Merwe [mailto:[email protected]]
Sent: Monday, May 31, 2004 8:58 AM
To: Linux Advanced Routing & Traffic Control
Subject: [LARTC] shaping

Quoted 6 lines

Hi!

Is there any way to do just plain vanilla TBF (Token Buck Filter) type shaping on a group of ips/networks, not an entire interface.

Currently the only way I know how to shape in Linux is to use HTB or

CBQ,

Quoted 1 line

but both of these need a total rate and then you need to subdivide

that

Quoted 1 line

into classes. That is not what I want. All I want is Cisco generic

traffic

Quoted 1 line

shaping style shaping (or similar to how the old shaper module

worked),

Quoted 20 lines

iow
I don't want to specify how much bandwidth I have, I just want to make sure
that any particular group never exceeds a given rate.

--

Regards
Abraham

TODAY the Pond!
TOMORROW the World!

                -- Frogs (1972)

___________________________________________________
Abraham vd Merwe - Frogfoot Networks CC
1st Floor, Albion Springs, 183 Main Road, Newlands
Phone: +27 21 689 3873 Cell: +27 82 565 4451
Http: http://www.frogfoot.net/ Email: [email protected]

Quoted 3 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#4 lore raw

Re: [LARTC] shaping

In reply to Isak Badenhorst

Hi Mike >@2004.05.31_15:17:21_+0200

I have thought of that, but that is not ideal for a couple of reasons, the two most important being:

(a) You can't add 1 leaf node at a time with HTB or CBQ which makes it rather messy to add large numbers of rules.

(b) I'm not sure what HTB will do if you lie about the total rate. We have tried this on various occassions and in all cases HTB just didn't work if you did this - not even the guaranteed rates worked properly.

Quoted 34 lines

Not the answer you're looking for, but why not just specify your total bandwidth being much larger than your interface actually is and then subdividing into your groups?

Mike.

Quoted 6 lines

-----Original Message-----
From: Abraham van der Merwe [mailto:[email protected]]
Sent: Monday, May 31, 2004 8:58 AM
To: Linux Advanced Routing & Traffic Control
Subject: [LARTC] shaping

Quoted 6 lines

Hi!

Is there any way to do just plain vanilla TBF (Token Buck Filter) type shaping on a group of ips/networks, not an entire interface.

Currently the only way I know how to shape in Linux is to use HTB or

CBQ,

Quoted 1 line

but both of these need a total rate and then you need to subdivide

that

Quoted 1 line

into classes. That is not what I want. All I want is Cisco generic

traffic

Quoted 1 line

shaping style shaping (or similar to how the old shaper module

worked),

Quoted 4 lines

iow
I don't want to specify how much bandwidth I have, I just want to make sure
that any particular group never exceeds a given rate.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Signature · 16 lines
Regards
 Abraham

TODAY the Pond!
TOMORROW the World!
                -- Frogs (1972)

___________________________________________________
 Abraham vd Merwe - Frogfoot Networks CC
 1st Floor, Albion Springs, 183 Main Road, Newlands
 Phone: +27 21 689 3873 Cell: +27 82 565 4451
 Http: http://www.frogfoot.net/ Email: [email protected]

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/