borrowing only from parent]
If you read the manual, the algorithm will not work correctly with {,c}burst < MTU ...
devik
Quoted 9 lines · Anton Yurchenko
Hello,
for example I have a parent class 1:1 defined as:
tc qdisc add dev eth0 root handle 1: htb default 12
# shape at 15 kbit almost no borrowing and no bursts tc class add dev eth0 parent 1: classid 1:1 htb rate 15kbit ceil 1kbit burst 1b cburst 1b
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 19 lines · Stef Coene
Quoted 10 lines · Anton Yurchenko
Hello,
for example I have a parent class 1:1 defined as:
tc qdisc add dev eth0 root handle 1: htb default 12
# shape at 15 kbit almost no borrowing and no bursts tc class add dev eth0 parent 1: classid 1:1 htb rate 15kbit ceil 1kbit burst 1b cburst 1bQuoted 7 lines
# and sibling classes # shape at 5kbit and borrow up to 5 kbit no burst tc class add dev eth0 parent 1:1 classid 1:10 htb rate 5kbit ceil 5kbit burst 1b cburst 1b # shape at 10kbit and borrow up to 10 kbit no burst tc class add dev eth0 parent 1:1 classid 1:11 htb rate 10kbit ceil 10kbps burst 1b cburst 1b
Quoted 5 lines
Try ceil 15kbit for the class 1:10 and 1:11.
And 15kbit is a very low speed to shape at. Why are you doing so ? And you also typed kbps, but kbps = kilobyte/s = 8 kilobit/s = 8 kbit.
That was just a mistype i typed in actualy your test config for htb, modified for my expalme purposes :)) this is the actual config:
tc -s -d class show dev eth0:
-----------
class htb 1:101 parent 1:1 prio 0 rate 40Kbit ceil 100Kbit burst 0b/8 mpu 0b cburst 0b/8 mpu 0b quantum 512 level 0 Sent 279738 bytes 4197 pkts (dropped 0, overlimits 9703) lended: 4197 borrowed: 0 giants: 0 injects: 0
tokens: -95938 ctokens: -191877
class htb 1:1 root prio 0 rate 100Kbit ceil 1Kbit burst 0b/8 mpu 0b cburst 0b/8 mpu 0b quantum 1280 level 3 Sent 605011 bytes 9017 pkts (dropped 0, overlimits 0) rate 233bps 3pps lended: 566 borrowed: 0 giants: 0 injects: 0
tokens: -9594 ctokens: -59999999
class htb 1:100 parent 1:1 prio 0 rate 60Kbit ceil 100Kbit burst 0b/8 mpu 0b cburst 0b/8 mpu 0b quantum 768 level 0 Sent 325273 bytes 4820 pkts (dropped 0, overlimits 12652) rate 233bps 3pps lended: 4254 borrowed: 566 giants: 0 injects: 0
tokens: -15989 ctokens: -9594
-----------
tc qdisc show dev eth0
-----------
qdisc htb 1: dev eth0 r2q 10 default 400 dcache 0deq_util 1/250000 deq_rate 1 trials_per_deq 0dcache_hits 0 direct_packets 71955
Chain PREROUTING (policy ACCEPT)
target prot opt source destination -----------
tc filter show dev eth0
-----------
Chain POSTROUTING (policy ACCEPT)
target prot opt source destination filter parent 1: protocol ip pref 3 fw filter parent 1: protocol ip pref 3 fw handle 0x1 classid 1:100 filter parent 1: protocol ip pref 3 fw handle 0x2 classid 1:101
-----------
iptables -t mangle -L:
-----------
Chain INPUT (policy ACCEPT)
target prot opt source destination MARK all -- srchost1 anywhere MARK set 0x1 MARK all -- srchost2 anywhere MARK set 0x2
Chain FORWARD (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination MARK all -- anywhere srchost1 MARK set 0x1 MARK all -- anywhere srchost2 MARK set 0x2
-----------
Also: whe I mark pakets for example only on OUTPUT chain, it will apply only to packets from me? so I should do it for in and out right?
Anyway with this config when I download from srchost1 (I use wget to measure) via ftp wget shows from 140 to 240 KB/s and for srchost2 via http I get from 70 to 100 KB/s. nothing like I expected :)
Thanks
Anton
Quoted 4 lines · Martin Devera
If you read the manual, the algorithm will not work correctly with {,c}burst < MTU ...
devik
I just tried to change {,c}burst to 1600, or leaving them by default but no visible result. here is the latest tc -s -d class show dev eth0
class htb 1:101 parent 1:1 prio 0 rate 40Kbit ceil 40Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 512 level 0 Sent 392526 bytes 5898 pkts (dropped 0, overlimits 15394) lended: 5898 borrowed: 0 giants: 0 injects: 0
tokens: -11905 ctokens: -11905
class htb 1:1 root prio 0 rate 100Kbit ceil 1Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 1280 level 3 Sent 956111 bytes 14168 pkts (dropped 0, overlimits 0) rate 12bps lended: 566 borrowed: 0 giants: 0 injects: 0
tokens: 224179 ctokens: -59999999
class htb 1:100 parent 1:1 prio 0 rate 60Kbit ceil 60Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 768 level 0 Sent 563585 bytes 8270 pkts (dropped 0, overlimits 20093) rate 11bps lended: 7704 borrowed: 566 giants: 0 injects: 0
tokens: -14100 ctokens: -14100
thanks,
Anton
Quoted 4 lines · Martin Devera
If you read the manual, the algorithm will not work correctly with {,c}burst < MTU ...
devik
I just tried to change {,c}burst to 1600, or leaving them by default but no visible result. here is the latest tc -s -d class show dev eth0
class htb 1:101 parent 1:1 prio 0 rate 40Kbit ceil 40Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 512 level 0 Sent 392526 bytes 5898 pkts (dropped 0, overlimits 15394) lended: 5898 borrowed: 0 giants: 0 injects: 0
tokens: -11905 ctokens: -11905
class htb 1:1 root prio 0 rate 100Kbit ceil 1Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 1280 level 3 Sent 956111 bytes 14168 pkts (dropped 0, overlimits 0) rate 12bps lended: 566 borrowed: 0 giants: 0 injects: 0
tokens: 224179 ctokens: -59999999
class htb 1:100 parent 1:1 prio 0 rate 60Kbit ceil 60Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 768 level 0 Sent 563585 bytes 8270 pkts (dropped 0, overlimits 20093) rate 11bps lended: 7704 borrowed: 566 giants: 0 injects: 0
tokens: -14100 ctokens: -14100
thanks,
Anton
Quoted 10 lines
I just tried to change {,c}burst to 1600, or leaving them by default but no visible result.
here is the latest tc -s -d class show dev eth0class htb 1:101 parent 1:1 prio 0 rate 40Kbit ceil 40Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 512 level 0 Sent 392526 bytes 5898 pkts (dropped 0, overlimits 15394) lended: 5898 borrowed: 0 giants: 0
injects: 0
tokens: -11905 ctokens: -11905
Quoted 5 lines
class htb 1:1 root prio 0 rate 100Kbit ceil 1Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 1280 level 3 Sent 956111 bytes 14168 pkts (dropped 0, overlimits 0) rate 12bps lended: 566 borrowed: 0 giants: 0
injects: 0
tokens: 224179 ctokens: -59999999
ceil 1kbit !!??
devik
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 10 lines · Martin Devera
Quoted 10 lines
I just tried to change {,c}burst to 1600, or leaving them by default but no visible result.
here is the latest tc -s -d class show dev eth0class htb 1:101 parent 1:1 prio 0 rate 40Kbit ceil 40Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 512 level 0 Sent 392526 bytes 5898 pkts (dropped 0, overlimits 15394) lended: 5898 borrowed: 0 giants: 0
injects: 0
tokens: -11905 ctokens: -11905
Quoted 9 lines
Quoted 6 lines
class htb 1:1 root prio 0 rate 100Kbit ceil 1Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 1280 level 3 Sent 956111 bytes 14168 pkts (dropped 0, overlimits 0) rate 12bps lended: 566 borrowed: 0 giants: 0
injects: 0
tokens: 224179 ctokens: -59999999ceil 1kbit !!??
Wouldnt it prevent 1:1 from borrowing from 1: ? I think Im missunderstanding the ceil. As I see it it is if I fe. have rate 100kbit and ceil 100kbit then 1:1 would go at at least 100kbit and can borrow 100kbit from 1: . Which is in my case unwanted. I want to limit 1:1 to 100kbit without abilyti to borrow. 1:100 and 1:101 could borrow from one another up to the max rate of 1:1 ( 100 kbit) that is what I want ot achieve.
thanks,
Anton
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 3 lines
Quoted 2 lines
ceil 1kbit !!??
Wouldn
t it prevent 1:1 from borrowing from 1: ? I think Im
it will but also it will prevent 1:1 to lend anything.
Quoted 3 lines
missunderstanding the ceil. As I see it it is if I fe. have rate 100kbit and ceil 100kbit then 1:1 would go at at least 100kbit and can borrow 100kbit from 1: . Which is in my case unwanted. I want to limit 1:1 to
no 100/100 is it can do 100 and 100 is also it;s maximal rate. Cail should be greater or the same in respec to rate. devik
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hello,
After your explaining now I think I get the meaning of htb options and here is my config , which still sadly doesnt work. Downloads from srchost1 and srchost2 go at full speed, and are not shaped. Though counters for respective classes increase.
tc -s -d show class dev eth0
-------------------------------------
class htb 1:101 parent 1:1 prio 0 rate 40Kbit ceil 100Kbit burst 1650b/8 mpu 0b cburst 1727b/8 mpu 0b quantum 512 level 0
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0 injects: 0
tokens: 628545 ctokens: 263144
class htb 1:1 root prio 0 rate 100Kbit ceil 100Kbit burst 1599b/8 mpu 0b cburst 1599b/8 mpu 0b quantum 1280 level 3
Sent 3131025 bytes 23836 pkts (dropped 0, overlimits 0)
rate 281bps 3pps
lended: 751 borrowed: 0 giants: 0 injects: 0
tokens: -8719 ctokens: -8719
class htb 1:100 parent 1:1 prio 0 rate 60Kbit ceil 100Kbit burst 1675b/8 mpu 0b cburst 1727b/8 mpu 0b quantum 768 level 0
Sent 36068 bytes 504 pkts (dropped 0, overlimits 538)
rate 281bps 3pps
lended: 319 borrowed: 185 giants: 0 injects: 0
tokens: -12135 ctokens: 10773
-------------------------------------
tc qdisc show dev eth0
-------------------------------------
qdisc htb 1: r2q 10 default 400 dcache 0
deq_util 1/83333 deq_rate 4 trials_per_deq 0
dcache_hits 0 direct_packets 94066
-------------------------------------
tc filter show dev eth0
-------------------------------------
filter parent 1: protocol ip pref 3 fw
filter parent 1: protocol ip pref 3 fw handle 0x1 classid 1:100 filter parent 1: protocol ip pref 3 fw handle 0x2 classid 1:101
-------------------------------------
iptables -t mangle -L
-------------------------------------
Chain PREROUTING (policy ACCEPT)
target prot opt source destination
Chain INPUT (policy ACCEPT)
target prot opt source destination MARK all -- sourcehost1 anywhere MARK set 0x1 MARK all -- sourcehost2 anywhere MARK set 0x2
Chain FORWARD (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination MARK all -- anywhere sourcehost1 MARK set 0x1 MARK all -- anywhere sourcehost2 MARK set 0x2
Chain POSTROUTING (policy ACCEPT)
target prot opt source destination
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
You are trying to shape downloads !? It will not work of course in this setup. You can shape output only. Or what do you want to shape ? devik
Quoted 6 lines · Anton Yurchenko
Hello,
After your explaining now I think I get the meaning of htb options and here is my config , which still sadly doesnt work. Downloads from srchost1 and srchost2 go at full speed, and are not shaped. Though counters for respective classes increase.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 4 lines · Martin Devera
You are trying to shape downloads !? It will not work of course in this setup. You can shape output only. Or what do you want to shape ? devik
ok I got it :)) that is what I suspected :)) finaly. that is common logic, I`m sorry, after reading some of the docs you go mad. my bad, thank you and Stef Coene very much for you help.
Anton
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
;) Try Patrick's IMQ version it should be able to do it.
Quoted 3 lines · Anton Yurchenko
ok I got it :)) that is what I suspected :)) finaly. that is common logic, I`m sorry, after reading some of the docs you go mad. my bad, thank you and Stef Coene very much for you help.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Question :
Quoted 2 lines
Quoted 2 lines
Has anyone ever managed to compile iproute2 from source, running a 2.4.x kernel ?
I have also managed to solve it in another way..
Here is how ...
Solution 1:
Well I have managed to fix the compile error on a kernel 2.4.x
If we have a look at the file, /usr/src/linux/include/linux/if_ether.h that you get from the different kernels, we notice a change.
On 2.2.x kernel...
#define ETH_P_ECHO 0x0200 /* Ethernet Echo packet */
On 2.4.x kernel...
#define ETH_P_PUP 0x0200 /* Xerox PUP packet */
Q: How to fix it ?
In the directory /lib of the source from the iproute2 tarball,
is a file called, 'll_proto.c'
In the file, there is an entry '__PF(ECHO,echo)' on line 36.
A: Remove this line, and try to compile it again.
Solution 2:
Quoted 12 lines
Using SGL :)
hvisage@meklon:~$ tar -zxf download/iproute2-2.4.7-now-ss020116-try.tar.gz hvisage@meklon:~$ cd iproute2/ hvisage@meklon:~/iproute2$ sed -e "s/UTILS_H/IPROUTE2_UTILS_H/g" < include/utils.h > include/iproute2_utils.h hvisage@meklon:~/iproute2$ for i in `find . -type f | xargs grep utils.h|grep :|cut -f 1 -d :`; do sed -e 's/"utils.h"/"iproute2_utils.h"/' <$i > $i.new;mv $i.new $i;done hvisage@meklon:~/iproute2$ make
Quoted 5 lines
QED ;^)
The reason:
there are a/usr/include/utils.hthat get's included before
theiproute2/include/utils.h:(
----
To unsubscribe from this list: send the line "unsubscribe glug" in the subject of a message to [email protected]. If you have a problem unsubscribing, please mail [email protected]
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
sorry for me previous mis-post.
It should have replied to the iproute compile problem chain.
My bad.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/