Skip to contentSkip to conversation

How to do Demasquerading before PREROUTING on one device for incoming packets?

LARTC Ramin Alidousti 1 participant 1 message May 2, 2002

lore
Share & tools
lore
#0 lore raw
Quoted 24 lines · Marc Vorwerk

Hello together,

we have one problem here, it is more an idealistic problem:

We have an PC - let us call him PC_1 - with one Ethernet adapter. This one is connected to the WWW with this adapter and also via several iptunnels to an specific PC_2 out there. Through these tunnels now IP packets with private IPaddresses reach PC_1. There they will now be routed by the default route to the WWW and so they leave eth0 and will be masqueraded ...

So on PC_1 we did:

iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE

defining the tunnel back to PC_2:
ip tunnel add tunl-4 mode ipip local <IP_form_PC_1> remote <IP_from_PC_2> tos inherit ip address add 192.168.104.1 dev tunl-4
ip link set dev tunl-4 up
ip route add default dev tunl-4 table 4

this is not so important now:
tc class add dev eth0 parent 20:1 classid 20:2 cbq bandwidth 1000000 rate 9000 allot 1514 weight 900 maxburst 20 avpkt 1000 isolated bounded tc qdisc add dev eth0 parent 20:2 sfq quantum 1514b perturb 15
tc filter add dev eth0 parent 20:0 protocol ip pref 2 u32 match u8 2 0xff at 21 flowid 20:2

Quoted 8 lines

what should be put back in the tunnel to PC_2:
ip rule add fwmark 2 pref 2 table 4
ip route flush cache

example for a ping:

        iptables -A PREROUTING -t mangle -d <private_IP_that_had_come_out_of_the_tunnel, eg 192.168.199.10> -s <destinationIP_of_server_in_the_WWW>
-p icmp -j MARK --set-mark 2
        iptables -A PREROUTING -t mangle -m mark --mark 2 -j ACCEPT

Your assumption is not correct about the dst of these packets. In the mangle table the dst would be PC_1 as you yourself experienced.

Quoted 3 lines

NOW the problem is that the returning IPpackets from the server in the WWW has the destination of PC_1 so the PREROUTING fails :O|

No, this doesn't make sense either. What you could do is to assign a second IP to your WWW and MASQ connections destined for that IP. This way you can mark the packets based on the src (WWW's second IP).

Ramin

Quoted 8 lines

So we had the idea to set up a dummy0 device and send all demasqueraded IPpackets to this dummy, because we know this must be a private IP:

        ip address add 192.168.4.1 dev dummy0                           
        ip link set dev dummy0 up
        ip route add 192.168.199.0 dev dummy0

So the idea was now that the PREROUTING should fetch the incoming packets from dummy0, but it did not work :o(

Quoted 9 lines

Do you have an idea to map the PREROUTING to a special (virtual) device - in this case the dummy0 - or to change the order of Demasquerading and PREROUTING?

I know that this whole set-up will work if I use a 3rd machine for the MASQUERADING, but this is really not smart ....

Thanks a lot for some hints and regards from Aachen, Marc, Heiko and Colin

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/