r2q
Hello,
I've installed htb3 on my simple config
(htb + sfq) . Something is now complaining that quantum is too small and suggest that r2q be changed.
There seems to be no documentation on this.
Ideas anyone?
Regards
John
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
It is documented in HTB manual. The complaint was not displayed before and sharing was silently wrong.
Quantum of leaf should be between 1500 and 60000 and it is computed as rate/r2q (or can be supplied independly).
So that if your maximal leaf rate is 1Mbit (120000Bps) then r2q should be 3. If max rate is 10kbit (1200Bps) then r2q should be 1. It is warning only and will not affect functionality, only precision. devik
Quoted 10 lines · john huttley
Hello,
I've installed htb3 on my simple config
(htb + sfq) . Something is now complaining that quantum is too small and suggest that r2q be changed.There seems to be no documentation on this.
Ideas anyone?
Quoted 10 lines
Regards
John
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
[LARTC] R2Q
In reply to john huttleyHello again,
I need to change the R2Q for my script, as setting the quantum manually for each class is painful. Can you tell me exactly where to set R2Q = x?
I get syntax errors all the time. Should it be specified for each class? I do not know where to place this setting...
Thanks in advance,
Vlad Mihai
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Re: [LARTC] R2Q
In reply to john huttleyQuoted 4 lines · Mihai Vlad
Hello again,
I need to change the R2Q for my script, as setting the quantum manually for each class is painful. Can you tell me exactly where to set R2Q = x?
If you add the htb qdisc.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.openprojects.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
[LARTC] R2Q
In reply to john huttleyHere is a quote from docum.org:
-------------------------------------------------------------------------
Counting packets with quantum can be strange. If we have a low rate class (rate = 5kbit), default quantum = 5000 / 10 = 500 bytes. But most packets are more then 500 bytes. Htb version 1 and 2 uses DRR, so a packet larger then 1000 bytes will be sent and it will remember how much it sent and wait until the packet is paid back before another packet is send. So if you send 1000 byte, next time the class is polled, you will not be allowed to send.
Htb3 uses the WRR scheduler. When a packet with size > quantum is sent, it will be sent and an error that the quantum is too small will be logged. But there is no pay back. The WRR scheduler is faster then the DRR scheduler. So make sure quantum is bigger then the default packet size. For 15 kbyte/s and default r2q, quantum is 1500 and this is exactly the maximum packet size. If you want to tune htb for rates smaller then 15 kbyte/s, you can manually set the r2q and/or quantum.
----------------------------------------------------------------------------
Assuming the 5kbit example (kbit not kbytes) and that the R2Q is 10, we can compute the quantum like this:
5 kbit = 5000 bit
5000 bit / 10 = 500 byte
Is it bytes or bits?
I guess the first term (the rate) is measured in bits and the quantum in bytes.
Taking into account the second example (15 kbyte), we compute the quantum like this:
15 kbyte = 15000 byte
15000 byte / 10 = 1500 byte
Is it bytes or bits?
So, in order to have a fully functional HTB 3 script I need to have each of my class rates bigger than 15 kbyte? This is about 120 kbit.
What happens if I need lower rates like 8 kbit?
Do I need to set up the quantum manually?
Please don't laugh if I am talking nonsense, but I cannot figure it out...
Thanks,
Mihai
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Re: [LARTC] R2Q
In reply to john huttleyQuoted 19 lines · Mihai Vlad
Here is a quote from docum.org:
-------------------------------------------------------------------------
Counting packets with quantum can be strange. If we have a low rate class (rate = 5kbit), default quantum = 5000 / 10 = 500 bytes. But most packets are more then 500 bytes. Htb version 1 and 2 uses DRR, so a packet larger then 1000 bytes will be sent and it will remember how much it sent and wait until the packet is paid back before another packet is send. So if you send 1000 byte, next time the class is polled, you will not be allowed to send.Htb3 uses the WRR scheduler. When a packet with size > quantum is sent, it will be sent and an error that the quantum is too small will be logged. But there is no pay back. The WRR scheduler is faster then the DRR scheduler. So make sure quantum is bigger then the default packet size. For 15 kbyte/s and default r2q, quantum is 1500 and this is exactly the maximum packet size. If you want to tune htb for rates smaller then 15 kbyte/s, you can manually set the r2q and/or quantum.
---------------------------------------------------------------------------
Quoted 6 lines
Assuming the 5kbit example (kbit not kbytes) and that the R2Q is 10, we can compute the quantum like this:
5 kbit = 5000 bit
5000 bit / 10 = 500 byteIs it bytes or bits?
bytes
Quoted 2 lines
I guess the first term (the rate) is measured in bits and the quantum in bytes.
Indeed.
Quoted 6 lines
Taking into account the second example (15 kbyte), we compute the quantum like this:
15 kbyte = 15000 byte
15000 byte / 10 = 1500 byteIs it bytes or bits?
bytes
Quoted 2 lines
So, in order to have a fully functional HTB 3 script I need to have each of my class rates bigger than 15 kbyte? This is about 120 kbit.
Indeed.
Quoted 1 line
What happens if I need lower rates like 8 kbit?
You can specify a lower r2q if you add the htb qdisc. And/or you can specify quantum when you add a class.
Quoted 1 line
Do I need to set up the quantum manually?
If you don't find a good r2q, yes.
Stef
Signature · 8 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.openprojects.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hi...
I'm working with HTB, and have a question...
what happen if I create a class of "8kbit" ??
I get a log :
"HTB: quantum of class .... is small. Consider r2q change"
but, my r2q=1 I can't reduce that variable...
how must I procced ?
Thank you!
mac
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Simply set quantum manualy,
now quantum = rate / r2q
set quantum to one mtu ( 1500 bytes)
Remember that quantum affects priority bigger quantum means higer priority.
----- Original Message -----
From: "ThE LinuX_KiD" <[email protected]>
To: "lartc" <[email protected]>
Sent: Friday, March 19, 2004 11:20 PM
Subject: [LARTC] r2q
Quoted 12 lines
Hi...
I'm working with HTB, and have a question...
what happen if I create a class of '"'8kbit'"' ??
I get a log :
'"'HTB: quantum of class .... is small. Consider r2q change'"'
but, my r2q=1 I can't reduce that variable...
Quoted 8 lines
how must I procced ?
Thank you!
mac
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
quantum = rate (bytes) / r2q
Rate=8 Kbits/s = 1 Kbyte/s = 1024 Bytes
r2q=1
quantum = 1024/1.
Then Quantum = 1024
But MTU00 => MTU > Quantum
Must I set MTU to 1024 ????
Thank you!
Andres.
-> Simply set quantum manualy,
-> now quantum = rate / r2q
-> set quantum to one mtu ( 1500 bytes)
->
-> Remember that quantum affects priority
-> bigger quantum means higer priority.
->
->
-> ----- Original Message -----
-> From: "ThE LinuX_KiD" <[email protected]>
-> To: "lartc" <[email protected]>
-> Sent: Friday, March 19, 2004 11:20 PM
-> Subject: [LARTC] r2q
->
->
-> > Hi...
-> >
-> > I'm working with HTB, and have a question...
-> >
-> > what happen if I create a class of '"'8kbit'"' ??
-> >
-> > I get a log :
-> >
-> > '"'HTB: quantum of class .... is small. Consider r2q change'"' -> >
-> > but, my r2q=1 I can't reduce that variable...
-> >
-> > how must I procced ?
-> >
-> > Thank you!
-> > mac
-> > _______________________________________________
-> > LARTC mailing list / [email protected]
-> > http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
-> >
-> _______________________________________________
-> LARTC mailing list / [email protected]
-> http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
->
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Specify a quantum value(MTU suggested) on the class with 8 kbit.
Rubens
Quoted 12 lines · ThE LinuX_KiD
Hi...
I'm working with HTB, and have a question...
what happen if I create a class of "8kbit" ??
I get a log :
"HTB: quantum of class .... is small. Consider r2q change"
but, my r2q=1 I can't reduce that variable...
Quoted 8 lines
how must I procced ?
Thank you!
mac
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
I'm still confused about choosing r2q and quantum values.
I've got different classes. Some have rate as low as 16Kbit and some have 2048Kbit. I'm using default r2q value ie 10 I guess. Also I'm using same quantum value for all the classes (ie quantum 1500) whatever their rate is. Is this a good practice? I don't know. For r2q I think the value that i'm using for quantuim (1500) is very high! In this case Should I lower the quantum value or the r2q value.
I think I have two options:
1. r2q=1 and qunatum00
2. r2q and quantum0
which one is better?
with regards,
Bikrant
Quoted 34 lines · Roy
Simply set quantum manualy,
now quantum = rate / r2q
set quantum to one mtu ( 1500 bytes)Remember that quantum affects priority bigger quantum means higer priority.
----- Original Message -----
From: "ThELinuX_KiD" <[email protected]>
To: "lartc" <[email protected]>
Sent: Friday, March 19, 2004 11:20 PM
Subject: [LARTC] r2qQuoted 12 lines
Hi...
I'm working with HTB, and have a question...
what happen if I create a class of '"'8kbit'"' ??
I get a log :
'"'HTB: quantum of class .... is small. Consider r2q change'"'
but, my r2q=1 I can't reduce that variable...
Quoted 7 lines
how must I procced ?
Thank you!
mac
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 3 lines
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Thank you, Roy !
I've setted quantum to 1500 when:
quantum = rate / r2q < 1500
and error logs are stopped.
In other hand, I get a new warning message:
"HTB: quantum of class .... is BIG. Consider r2q change"
because, some rates are about 1500kbits, then with above formula quantum is about 192000 > 60000
But, I can't change r2q, then I put "quantum 55000" on this rules, and error has been fixed.
Is correct the value "quantum 55000" ?
Or I must put mtu (1500) value for quantum ?
Thank you!
Andres.
->
->
-> No,
-> leave mtu unchanged, or you risk to have problems with some dumb servers. -> just set qantum to 1500, for each rule when it is lower than mtu -> bu default
->
-> (quantum = rate (bytes) / r2q) this formula is used by tc to calculate -> default quantum
-> you do not need to use it.
->
->
-> ----- Original Message -----
-> From: "ThE LinuX_KiD" <[email protected]>
-> To: "lartc" <[email protected]>
-> Sent: Saturday, March 20, 2004 10:17 PM
-> Subject: RE: [LARTC] r2q
->
->
-> >
-> >
-> >
-> >
-> > Rate=8 Kbits/s = 1 Kbyte/s = 1024 Bytes
-> > r2q=1
-> >
-> > quantum = 1024/1.
-> >
-> > Then Quantum = 1024
-> >
-> > But MTU00 => MTU > Quantum
-> >
-> > Must I set MTU to 1024 ????
-> >
-> > Thank you!
-> >
-> > Andres.
-> >
-> >
-> >
-> > -> Simply set quantum manualy,
-> > -> now quantum = rate / r2q
-> > -> set quantum to one mtu ( 1500 bytes)
-> > ->
-> > -> Remember that quantum affects priority
-> > -> bigger quantum means higer priority.
-> > ->
-> > ->
-> > -> ----- Original Message -----
-> > -> From: '"'ThE LinuX_KiD'"' <[email protected]> -> > -> To: '"'lartc'"' <[email protected]>
-> > -> Sent: Friday, March 19, 2004 11:20 PM
-> > -> Subject: [LARTC] r2q
-> > ->
-> > ->
-> > -> > Hi...
-> > -> >
-> > -> > I'm working with HTB, and have a question...
-> > -> >
-> > -> > what happen if I create a class of ''"''8kbit''"'' ?? -> > -> >
-> > -> > I get a log :
-> > -> >
-> > -> > ''"''HTB: quantum of class .... is small. Consider r2q change''"'' -> > -> >
-> > -> > but, my r2q=1 I can't reduce that variable...
-> > -> >
-> > -> > how must I procced ?
-> > -> >
-> > -> > Thank you!
-> > -> > mac
-> > -> > _______________________________________________
-> > -> > LARTC mailing list / [email protected]
-> > -> > http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
-> http://lartc.org/
-> > -> >
-> > -> _______________________________________________
-> > -> LARTC mailing list / [email protected]
-> > -> http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
http://lartc.org/
Quoted 5 lines
->
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
I newer saw warning mesage about quantum too big.
but probably it is ok to have ANY quantum which is greater than mtu.
probabaly you shpuld not set quantum to 1500 if it is 50000 by defaul, unless you want to lower that class priority very much.
but so high quantums can make trafic very bursty. so you may set that quantum to 15000 for better result.
this will make these classes priority proportion as 1 to 10 ( 1 packet of spare trafic for slow class to 10 packets for fast class)
----- Original Message -----
From: "ThE LinuX_KiD" <[email protected]>
To: "lartc" <[email protected]>
Cc: "Roy" <[email protected]>
Sent: Monday, March 22, 2004 8:50 PM
Subject: RE: [LARTC] r2q
Quoted 33 lines
Thank you, Roy !
I've setted quantum to 1500 when:
quantum = rate / r2q < 1500
and error logs are stopped.
In other hand, I get a new warning message:
'"'HTB: quantum of class .... is BIG. Consider r2q change'"'
because, some rates are about 1500kbits, then with above formula quantum is about 192000 > 60000
But, I can't change r2q, then I put '"'quantum 55000'"' on this rules, and error has been fixed.
Is correct the value '"'quantum 55000'"' ?
Or I must put mtu (1500) value for quantum ?Thank you!
Andres.
Quoted 4 lines
->
->
-> No,
-> leave mtu unchanged, or you risk to have problems with some dumb
servers.
Quoted 69 lines
-> just set qantum to 1500, for each rule when it is lower than mtu -> bu default
->
-> (quantum = rate (bytes) / r2q) this formula is used by tc to calculate -> default quantum
-> you do not need to use it.
->
->
-> ----- Original Message -----
-> From: '"'ThELinuX_KiD'"' <[email protected]>
-> To: '"'lartc'"' <[email protected]>
-> Sent: Saturday, March 20, 2004 10:17 PM
-> Subject: RE: [LARTC] r2q
->
->
-> >
-> >
-> >
-> >
-> > Rate=8 Kbits/s = 1 Kbyte/s = 1024 Bytes
-> > r2q=1
-> >
-> > quantum = 1024/1.
-> >
-> > Then Quantum = 1024
-> >
-> > But MTU00 => MTU > Quantum
-> >
-> > Must I set MTU to 1024 ????
-> >
-> > Thank you!
-> >
-> > Andres.
-> >
-> >
-> >
-> > -> Simply set quantum manualy,
-> > -> now quantum = rate / r2q
-> > -> set quantum to one mtu ( 1500 bytes)
-> > ->
-> > -> Remember that quantum affects priority
-> > -> bigger quantum means higer priority.
-> > ->
-> > ->
-> > -> ----- Original Message -----
-> > -> From: ''"''ThELinuX_KiD''"'' <[email protected]> -> > -> To: ''"''lartc''"'' <[email protected]>
-> > -> Sent: Friday, March 19, 2004 11:20 PM
-> > -> Subject: [LARTC] r2q
-> > ->
-> > ->
-> > -> > Hi...
-> > -> >
-> > -> > I'm working with HTB, and have a question...
-> > -> >
-> > -> > what happen if I create a class of '''"'''8kbit'''"''' ?? -> > -> >
-> > -> > I get a log :
-> > -> >
-> > -> > '''"'''HTB: quantum of class .... is small. Consider r2q change'''"'''
-> > -> >
-> > -> > but, my r2q=1 I can't reduce that variable...
-> > -> >
-> > -> > how must I procced ?
-> > -> >
-> > -> > Thank you!
-> > -> > mac
-> > -> > _______________________________________________
Quoted 15 lines
-> > -> > LARTC mailing list / [email protected] -> > -> > http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
-> http://lartc.org/
-> > -> >
-> > -> _______________________________________________ -> > -> LARTC mailing list / [email protected] -> > -> http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
http://lartc.org/Quoted 5 lines
->
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Ok, in order to conclude: is OK next table ?
QUANTUM values for HTB:
RATE --- QUANTUM
----------------------------------------------
8k --> set QUANTUM = 1500
16k --> Quantum is automatic by HTB algorithm 32k --> Quantum is automatic by HTB algorithm 64k --> Quantum is automatic by HTB algorithm 256k --> Quantum is automatic by HTB algorithm 512k --> set QUANTUM = 15000
----------------------------------------------
each with r2q=1
Also, I set r2q=1 on root class, in order to support diferentes rates.
Thank you!
andres.
-> -----Mensaje original-----
-> De: [email protected] [mailto:[email protected]]En -> nombre de Roy
-> Enviado el: Martes, 23 de Marzo de 2004 12:13 p.m.
-> Para: lartc
-> Asunto: Re: [LARTC] r2q
->
->
-> I newer saw warning mesage about quantum too big.
-> but probably it is ok to have ANY quantum which is greater than mtu. ->
-> probabaly you shpuld not set quantum to 1500 if it is 50000 by defaul, -> unless you want to lower that class priority very much.
->
-> but so high quantums can make trafic very bursty.
-> so you may set that quantum to 15000 for better result.
->
-> this will make these classes priority proportion as 1 to 10 ( 1 packet of -> spare trafic for slow class to 10 packets for fast class)
->
-> ----- Original Message -----
-> From: "ThE LinuX_KiD" <[email protected]>
-> To: "lartc" <[email protected]>
-> Cc: "Roy" <[email protected]>
-> Sent: Monday, March 22, 2004 8:50 PM
-> Subject: RE: [LARTC] r2q
->
->
-> >
-> > Thank you, Roy !
-> >
-> > I've setted quantum to 1500 when:
-> >
-> > quantum = rate / r2q < 1500
-> >
-> > and error logs are stopped.
-> >
-> > In other hand, I get a new warning message:
-> >
-> > '"'HTB: quantum of class .... is BIG. Consider r2q change'"' -> >
-> > because, some rates are about 1500kbits, then with
-> > above formula quantum is about 192000 > 60000
-> >
-> > But, I can't change r2q, then I put '"'quantum 55000'"'
-> > on this rules, and error has been fixed.
-> >
-> > Is correct the value '"'quantum 55000'"' ?
-> > Or I must put mtu (1500) value for quantum ?
-> >
-> > Thank you!
-> >
-> > Andres.
-> >
-> >
-> >
-> >
-> >
-> >
-> >
-> >
-> > ->
-> > ->
-> > -> No,
-> > -> leave mtu unchanged, or you risk to have problems with some dumb -> servers.
-> > -> just set qantum to 1500, for each rule when it is lower than mtu -> > -> bu default
-> > ->
-> > -> (quantum = rate (bytes) / r2q) this formula is used by tc -> to calculate
-> > -> default quantum
-> > -> you do not need to use it.
-> > ->
-> > ->
-> > -> ----- Original Message -----
-> > -> From: '"'ThE LinuX_KiD'"' <[email protected]> -> > -> To: '"'lartc'"' <[email protected]>
-> > -> Sent: Saturday, March 20, 2004 10:17 PM
-> > -> Subject: RE: [LARTC] r2q
-> > ->
-> > ->
-> > -> >
-> > -> >
-> > -> >
-> > -> >
-> > -> > Rate=8 Kbits/s = 1 Kbyte/s = 1024 Bytes
-> > -> > r2q=1
-> > -> >
-> > -> > quantum = 1024/1.
-> > -> >
-> > -> > Then Quantum = 1024
-> > -> >
-> > -> > But MTU00 => MTU > Quantum
-> > -> >
-> > -> > Must I set MTU to 1024 ????
-> > -> >
-> > -> > Thank you!
-> > -> >
-> > -> > Andres.
-> > -> >
-> > -> >
-> > -> >
-> > -> > -> Simply set quantum manualy,
-> > -> > -> now quantum = rate / r2q
-> > -> > -> set quantum to one mtu ( 1500 bytes)
-> > -> > ->
-> > -> > -> Remember that quantum affects priority
-> > -> > -> bigger quantum means higer priority.
-> > -> > ->
-> > -> > ->
-> > -> > -> ----- Original Message -----
-> > -> > -> From: ''"''ThE LinuX_KiD''"'' <[email protected]> -> > -> > -> To: ''"''lartc''"'' <[email protected]>
-> > -> > -> Sent: Friday, March 19, 2004 11:20 PM
-> > -> > -> Subject: [LARTC] r2q
-> > -> > ->
-> > -> > ->
-> > -> > -> > Hi...
-> > -> > -> >
-> > -> > -> > I'm working with HTB, and have a question...
-> > -> > -> >
-> > -> > -> > what happen if I create a class of '''"'''8kbit'''"''' ?? -> > -> > -> >
-> > -> > -> > I get a log :
-> > -> > -> >
-> > -> > -> > '''"'''HTB: quantum of class .... is small. Consider r2q -> > change'''"'''
-> > -> > -> >
-> > -> > -> > but, my r2q=1 I can't reduce that variable...
-> > -> > -> >
-> > -> > -> > how must I procced ?
-> > -> > -> >
-> > -> > -> > Thank you!
-> > -> > -> > mac
-> > -> > -> > _______________________________________________ -> > -> > -> > LARTC mailing list / [email protected]
-> > -> > -> > http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
-> > -> http://lartc.org/
-> > -> > -> >
-> > -> > -> _______________________________________________
-> > -> > -> LARTC mailing list / [email protected]
-> > -> > -> http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
-> > http://lartc.org/
-> > > ->
-> > > _______________________________________________
-> > > LARTC mailing list / [email protected]
-> > > http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:
http://lartc.org/
Quoted 3 lines
Quoted 1 line
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 2 lines · Roy
I newer saw warning mesage about quantum too big.
but probably it is ok to have ANY quantum which is greater than mtu.
There is a maximum of 60000 for quantum to prevent class starvation.
Stef
Signature · 7 lines
[email protected] "Using Linux as bandwidth manager" http://www.docum.org/ #lartc @ irc.openprojects.net _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/