Skip to contentSkip to conversation

Ethloop?

LARTC King Yung Tong 2 participants 15 messages Jun 6, 2002 – Jun 7, 2002

lore
Share & tools
lore
#0 lore raw

Dear all,

I copy a Ethloop script for tc script, but no response??? Does anyone know how to use ethloop?

Ethloop;
#1st parameter -- time in milliseconds from program start #2nd parameter -- operation to do
#3rd parameter -- flow id
#4th parameter -- operation dependent
#
#e.g 5000 R 2 4500000
#means at time 5sec set rate of flow 2 to 4.5MBps
#Time should be in increasing time order
#Each line is executed at its time and will change the ongoing traffic generators

#example1
#Two flow simulation
# Two flow simulation

# lo will be used to TX and RX
0       i       P 0x10010       lo
0       i       P 0x10020       lo
# set simulation packet size to 1k
0       S      P 0x10010        1k
0       S      P 0x10020   1k
# start both flows
0       R      P 0x10010        100k
0       R      P 0x10020        100k
# flow 1 to 50k and 10k later
2000    R      P 0x10010        50k
4000    R      P 0x10020        10k
# finish at 6sec
6000    X      0        0

tc script:

echo Clean all the tc setup
./tc qdisc del dev eth0 root

echo Core router

echo Create qdisc and set default to 1:30
./tc qdisc add dev eth1 root handle 1: htb default 30
./tc class add dev eth1 parent 1: classid 1:1 htb rate 1.5Mbit burst 50k

echo Create class for EF
./tc class add dev eth1 parent 1:1 classid 1:10 htb rate 0.5Mbit ceil 0.5Mbit burst 50k prio 1

echo Create class for AF
./tc class add dev eth1 parent 1:2 classid 1:20 htb rate 0.5Mbit ceil 1Mbit burst 30K prio 1

echo Create class for BE
./tc class add dev eth1 parent 1:2 classid 1:30 htb rate 0.3Mbit ceil 1Mbit burst 30k prio 2
./tc qdisc add dev eth1 parent 1:30 red limit 1800KB min 150KB max 450KB burst 200 avpkt 1000 bandwidth 1Mbit probability 0.4

echo Filter
./tc filter add dev eth1 parent 1: protocol ip prio 1 u32 match ip tos 0xb8 0xff classid 1:10
./tc filter add dev eth1 parent 1: protocol ip prio 2 u32 match ip tos 0x0 0xff classid 1:20
./tc filter add dev eth1 parent 1: protocol ip prio 3 u32 match ip tos 0x98 0xff classid 1:30

Thank you

Patrick

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

What is the problem ? use cat ethloop_script|./ethloop for example ..
devik

Quoted 76 lines · King Yung Tong

Dear all,

I copy a Ethloop script for tc script, but no response??? Does anyone know how to use ethloop?

Ethloop;
#1st parameter -- time in milliseconds from program start #2nd parameter -- operation to do
#3rd parameter -- flow id
#4th parameter -- operation dependent
#
#e.g 5000 R 2 4500000
#means at time 5sec set rate of flow 2 to 4.5MBps
#Time should be in increasing time order
#Each line is executed at its time and will change the ongoing traffic generators

#example1
#Two flow simulation
# Two flow simulation

# lo will be used to TX and RX
0       i       P 0x10010       lo
0       i       P 0x10020       lo
# set simulation packet size to 1k
0       S      P 0x10010        1k
0       S      P 0x10020   1k
# start both flows
0       R      P 0x10010        100k
0       R      P 0x10020        100k
# flow 1 to 50k and 10k later
2000    R      P 0x10010        50k
4000    R      P 0x10020        10k
# finish at 6sec
6000    X      0        0

tc script:

echo Clean all the tc setup
./tc qdisc del dev eth0 root

echo Core router

echo Create qdisc and set default to 1:30
./tc qdisc add dev eth1 root handle 1: htb default 30
./tc class add dev eth1 parent 1: classid 1:1 htb rate 1.5Mbit burst 50k

echo Create class for EF
./tc class add dev eth1 parent 1:1 classid 1:10 htb rate 0.5Mbit ceil 0.5Mbit burst 50k prio 1

echo Create class for AF
./tc class add dev eth1 parent 1:2 classid 1:20 htb rate 0.5Mbit ceil 1Mbit burst 30K prio 1

echo Create class for BE
./tc class add dev eth1 parent 1:2 classid 1:30 htb rate 0.3Mbit ceil 1Mbit burst 30k prio 2
./tc qdisc add dev eth1 parent 1:30 red limit 1800KB min 150KB max 450KB burst 200 avpkt 1000 bandwidth 1Mbit probability 0.4

echo Filter
./tc filter add dev eth1 parent 1: protocol ip prio 1 u32 match ip tos 0xb8 0xff classid 1:10
./tc filter add dev eth1 parent 1: protocol ip prio 2 u32 match ip tos 0x0 0xff classid 1:20
./tc filter add dev eth1 parent 1: protocol ip prio 3 u32 match ip tos 0x98 0xff classid 1:30

Quoted 9 lines

Thank you

Patrick

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to King Yung Tong

Thank you for your reply :)
I try to follow chapter 6 on your user guide.

		1:1
	      /     \ 
 	    1:2     1:12
           /   \
         1:10   1:11
        (prio1) (prio2)

If 1:12 don't have any traffic, all the BW on 1:12 can be assigned to 1:2, is that right?

I try to put all these extra (from 1:12) to 1:10, my htb script is as follows, and I use ethloop to test and I found that 1:10 will not get the extra from 1:12. Could you tell me where I make a mistake? Thank you.

echo Clean all the tc setup
./tc qdisc del dev lo root
./tc qdisc add dev lo root handle 1: htb default 12

./tc class add dev lo parent 1: classid 1:1 htb rate 100kbps ./tc class add dev lo parent 1:1 classid 1:2 htb rate 40kbps ./tc class add dev lo parent 1:2 classid 1:10 htb rate 30kbps prio 0 ./tc class add dev lo parent 1:2 classid 1:11 htb rate 10kbps prio 1 ./tc class add dev lo parent 1:1 classid 1:12 htb rate 60kbps

echo qdisc
./tc qdisc add dev lo parent 1:10 handle 20: pfifo limit 5 ./tc qdisc add dev lo parent 1:11 handle 30: pfifo limit 5 ./tc qdisc add dev lo parent 1:12 handle 40: sfq perturb 10

Input for ethloop:

# lo will be used to TX and RX
0       i       0       lo
0       i       1       lo
0       i       2       lo
# set simulation packet size to 1k
0       S       0       1k
0       S       1       1k
0       S       2       1k
# flow 0 AE, flow 1  BE, flow 2 EF
0       P       0       0x10010
0       P       1       0x10011
0       P       2       0x10012
# start all flow at defined rate
0       R       0       30000
0       R       1       10000
0       R       2       60000
# Create extra at 1:12 and borrow this to 1:2 <------?
5000    R       0       30000
5000    R       1       10000
5000    R       2       0
# 1:10 and 1:11 and 1:10 should get higher value <------?
15000    R      0       40000
15000    R       1      20000
# finish at 8sec
25000    X      0        0

Result is to long, I use gnuplot and found that 1:10 at most get 30000.

Thank you for you help.

Pat

Quoted 6 lines · Martin Devera

What is the problem ? use cat ethloop_script|./ethloop for example ..
devik

On Thu, 6 Jun 2002, King Yung Tong wrote:

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to King Yung Tong

You either missed "ceil" parameter or it is missing on my page :) Without ceil it is the same as rate thus all classes are bounded in fact. Add ceil 100kbps to each line.
devik

Quoted 62 lines · King Yung Tong

Thank you for your reply :)
I try to follow chapter 6 on your user guide.

		1:1
	      /     \
 	    1:2     1:12
           /   \
         1:10   1:11
        (prio1) (prio2)

If 1:12 don't have any traffic, all the BW on 1:12 can be assigned to 1:2, is that right?

I try to put all these extra (from 1:12) to 1:10, my htb script is as follows, and I use ethloop to test and I found that 1:10 will not get the extra from 1:12. Could you tell me where I make a mistake? Thank you.

echo Clean all the tc setup
./tc qdisc del dev lo root
./tc qdisc add dev lo root handle 1: htb default 12

./tc class add dev lo parent 1: classid 1:1 htb rate 100kbps ./tc class add dev lo parent 1:1 classid 1:2 htb rate 40kbps ./tc class add dev lo parent 1:2 classid 1:10 htb rate 30kbps prio 0 ./tc class add dev lo parent 1:2 classid 1:11 htb rate 10kbps prio 1 ./tc class add dev lo parent 1:1 classid 1:12 htb rate 60kbps

echo qdisc
./tc qdisc add dev lo parent 1:10 handle 20: pfifo limit 5 ./tc qdisc add dev lo parent 1:11 handle 30: pfifo limit 5 ./tc qdisc add dev lo parent 1:12 handle 40: sfq perturb 10

Input for ethloop:

# lo will be used to TX and RX
0       i       0       lo
0       i       1       lo
0       i       2       lo
# set simulation packet size to 1k
0       S       0       1k
0       S       1       1k
0       S       2       1k
# flow 0 AE, flow 1  BE, flow 2 EF
0       P       0       0x10010
0       P       1       0x10011
0       P       2       0x10012
# start all flow at defined rate
0       R       0       30000
0       R       1       10000
0       R       2       60000
# Create extra at 1:12 and borrow this to 1:2 <------?
5000    R       0       30000
5000    R       1       10000
5000    R       2       0
# 1:10 and 1:11 and 1:10 should get higher value <------?
15000    R      0       40000
15000    R       1      20000
# finish at 8sec
25000    X      0        0

Result is to long, I use gnuplot and found that 1:10 at most get 30000.

Quoted 17 lines

Thank you for you help.

Pat

Quoted 6 lines · Martin Devera

What is the problem ? use cat ethloop_script|./ethloop for example ..
devik

On Thu, 6 Jun 2002, King Yung Tong wrote:

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#4 lore raw
In reply to King Yung Tong

Thank you for you answer, 1:10 is incresed but 1:20 is also increased and increase to the specific rate if I add 100kbps to every line.

In my case, I would like to put all the extra to 1:10 only, is that means I have to give 1:11 ceil to 10kbps. If it is, is that means I don't need prio paramter? How prio parameter works?

echo Clean all the tc setup
./tc qdisc del dev lo root

./tc qdisc add dev lo root handle 1: htb default 12

./tc class add dev lo parent 1: classid 1:1 htb rate 100kbps ceil 100kbps ./tc class add dev lo parent 1:1 classid 1:2 htb rate 40kbps ceil 100kbps ./tc class add dev lo parent 1:2 classid 1:10 htb rate 30kbps ceil 100kbps prio 0
./tc class add dev lo parent 1:2 classid 1:11 htb rate 10kbps ceil 100kbps <-- 10Kbps?? prio 1
./tc class add dev lo parent 1:1 classid 1:12 htb rate 60kbps ceil 100kbps

echo qdisc
./tc qdisc add dev lo parent 1:10 handle 20: pfifo limit 5 ./tc qdisc add dev lo parent 1:11 handle 30: pfifo limit 5 ./tc qdisc add dev lo parent 1:12 handle 40: sfq perturb 10

Quoted 5 lines · Martin Devera

You either missed "ceil" parameter or it is missing on my page :) Without ceil it is the same as rate thus all classes are bounded in fact. Add ceil 100kbps to each line.
devik

Quoted 82 lines
Quoted 79 lines · King Yung Tong

Thank you for your reply :)
I try to follow chapter 6 on your user guide.

		1:1
	      /     \
 	    1:2     1:12
           /   \
         1:10   1:11
        (prio1) (prio2)

If 1:12 don't have any traffic, all the BW on 1:12 can be assigned to 1:2, is that right?

I try to put all these extra (from 1:12) to 1:10, my htb script is as follows, and I use ethloop to test and I found that 1:10 will not get the extra from 1:12. Could you tell me where I make a mistake? Thank you.

echo Clean all the tc setup
./tc qdisc del dev lo root
./tc qdisc add dev lo root handle 1: htb default 12

./tc class add dev lo parent 1: classid 1:1 htb rate 100kbps ./tc class add dev lo parent 1:1 classid 1:2 htb rate 40kbps ./tc class add dev lo parent 1:2 classid 1:10 htb rate 30kbps prio 0 ./tc class add dev lo parent 1:2 classid 1:11 htb rate 10kbps prio 1 ./tc class add dev lo parent 1:1 classid 1:12 htb rate 60kbps

echo qdisc
./tc qdisc add dev lo parent 1:10 handle 20: pfifo limit 5 ./tc qdisc add dev lo parent 1:11 handle 30: pfifo limit 5 ./tc qdisc add dev lo parent 1:12 handle 40: sfq perturb 10

Input for ethloop:

# lo will be used to TX and RX
0       i       0       lo
0       i       1       lo
0       i       2       lo
# set simulation packet size to 1k
0       S       0       1k
0       S       1       1k
0       S       2       1k
# flow 0 AE, flow 1  BE, flow 2 EF
0       P       0       0x10010
0       P       1       0x10011
0       P       2       0x10012
# start all flow at defined rate
0       R       0       30000
0       R       1       10000
0       R       2       60000
# Create extra at 1:12 and borrow this to 1:2 <------?
5000    R       0       30000
5000    R       1       10000
5000    R       2       0
# 1:10 and 1:11 and 1:10 should get higher value <------?
15000    R      0       40000
15000    R       1      20000
# finish at 8sec
25000    X      0        0

Result is to long, I use gnuplot and found that 1:10 at most get 30000.

Thank you for you help.

Pat

Quoted 6 lines · Martin Devera

What is the problem ? use cat ethloop_script|./ethloop for example ..
devik

On Thu, 6 Jun 2002, King Yung Tong wrote:

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#5 lore raw
In reply to King Yung Tong
Quoted 2 lines

Thank you for you answer, 1:10 is incresed but 1:20 is also increased and increase to the specific rate if I add 100kbps to every line.

sounds weird. With higher prio 1:10 should get 90k and 1:11 10k.

Quoted 3 lines

In my case, I would like to put all the extra to 1:10 only, is that means I have to give 1:11 ceil to 10kbps. If it is, is that means I don't need prio paramter? How prio parameter works?

your understanding is ok, tge ceil 10k is correct - the prio is meant for lowering delay and change in excess distribution is only "secondary" product.

Port the resulting graph somewhere so I can look at it.

devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#6 lore raw
In reply to King Yung Tong

What version of HTB do you use ? Send me
tc -s -d class show dev xxx
outoput after test pic5 generation.
devik

Quoted 4 lines · King Yung Tong

Thank you again for you help!
Attach is the pic5 for the ceil equal to 100kbps for all line.
pic10limit for the ceil equal to 100kbps except 1:20.

Quoted 31 lines

My objective is to show if not prio is set the excess should allocate according to rate. If the prio is set, the high prio should get more.

Quoted 21 lines · Martin Devera
Quoted 2 lines

Thank you for you answer, 1:10 is incresed but 1:20 is also increased and increase to the specific rate if I add 100kbps to every line.

sounds weird. With higher prio 1:10 should get 90k and 1:11 10k.

Quoted 3 lines

In my case, I would like to put all the extra to 1:10 only, is that means I have to give 1:11 ceil to 10kbps. If it is, is that means I don't need prio paramter? How prio parameter works?

your understanding is ok, tge ceil 10k is correct - the prio is meant for lowering delay and change in excess distribution is only "secondary" product.

Port the resulting graph somewhere so I can look at it.

devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#7 lore raw
In reply to King Yung Tong

Thank you for you help.
Here is the HTB

echo Clean all the tc setup
./tc qdisc del dev lo root

./tc qdisc add dev lo root handle 1: htb default 12

./tc class add dev lo parent 1: classid 1:1 htb rate 100kbps ceil 100kbps ./tc class add dev lo parent 1:1 classid 1:2 htb rate 40kbps ceil 100kbps ./tc class add dev lo parent 1:2 classid 1:10 htb rate 30kbps ceil 100kbps prio 0
./tc class add dev lo parent 1:2 classid 1:11 htb rate 10kbps ceil 100kbps prio 1
./tc class add dev lo parent 1:1 classid 1:12 htb rate 60kbps ceil 100kbps

echo qdisc
./tc qdisc add dev lo parent 1:10 handle 20: pfifo limit 5 ./tc qdisc add dev lo parent 1:11 handle 30: pfifo limit 5 ./tc qdisc add dev lo parent 1:12 handle 40: sfq perturb 10

            _________________________1:11
	   /
	  /
_________/    ___________________ 1:12 (to should not be increse)???
	     /

-----------/

Result

0.5 23233 23233 0 0 7744 7744 0 0 44545 44545 0 0 1.0 28987 28987 0 0 9662 9662 0 0 57518 57518 0 0 1.5 29609 29609 0 0 10139 10139 0 0 59920 59920 0 0 2.0 30583 30583 0 0 10258 10258 0 0 59877 59877 0 0 2.5 28941 28941 0 0 10308 10308 0 0 58869 58869 0 0 3.0 30374 30374 0 0 10282 10282 0 0 60982 60982 0 0 3.5 29747 29747 0 0 8874 8874 0 0 59755 59755 0 0 4.0 29736 29736 0 0 9818 9818 0 0 59993 59993 0 0 4.5 30679 30679 0 0 10204 10204 0 0 14237 14237 0 0 5.0 29897 29897 0 0 10365 10365 0 0 3378 3378 0 0 5.5 30670 30670 0 0 10318 10318 0 0 802 802 0 0 6.0 30576 30576 0 0 10214 10214 0 0 190 190 0 0 6.5 28799 28799 0 0 10245 10245 0 0 45 45 0 0 7.0 30321 30321 0 0 8340 8340 0 0 11 11 0 0 7.5 45445 45445 0 0 18142 18142 0 0 3 3 0 0 8.0 48046 48046 0 0 19985 19985 0 0 1 1 0 0 8.5 50644 50644 0 0 17879 17879 0 0 0 0 0 0 9.0 50885 50885 0 0 19094 19094 0 0 0 0 0 0 9.5 50467 50467 0 0 20211 20211 0 0 0 0 0 0 10.0 49349 49349 0 0 20513 20513 0 0 0 0 0 0

Quoted 13 lines · Martin Devera
Quoted 2 lines

Thank you for you answer, 1:10 is incresed but 1:20 is also increased and increase to the specific rate if I add 100kbps to every line.

sounds weird. With higher prio 1:10 should get 90k and 1:11 10k.

Quoted 3 lines

In my case, I would like to put all the extra to 1:10 only, is that means I have to give 1:11 ceil to 10kbps. If it is, is that means I don't need prio paramter? How prio parameter works?

your understanding is ok, tge ceil 10k is correct - the prio is meant for lowering delay and change in excess distribution is only "secondary" product.

Quoted 8 lines

Port the resulting graph somewhere so I can look at it.

devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#8 lore raw
In reply to King Yung Tong

Here is the version and info.

Version htb3_2.4.17

[root@samwise htb]# ./tc -s -d class show dev lo
class htb 1:11 parent 1:2 leaf 30: prio 1 quantum 1024 rate 80Kbit ceil 800Kbit burst 1701b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 130048 bytes 127 pkts (dropped 0, overlimits 0)
rate 254bps
lended: 100 borrowed: 27 giants: 0
tokens: -60449 ctokens: 12800

class htb 1:1 root rate 800Kbit ceil 800Kbit burst 2623b/8 mpu 0b cburst 2623b/8 mpu 0b level 7 Sent 730112 bytes 713 pkts (dropped 0, overlimits
0)
rate 1426bps 1pps
lended: 81 borrowed: 0 giants: 0
tokens: 12800 ctokens: 12800

class htb 1:10 parent 1:2 leaf 20: prio 0 quantum 3072 rate 240Kbit ceil 800Kbit burst 1906b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 360448 bytes 352 pkts (dropped 0, overlimits 0)
rate 704bps
lended: 298 borrowed: 54 giants: 0
tokens: -36462 ctokens: 12800

class htb 1:2 parent 1:1 rate 320Kbit ceil 800Kbit burst 2008b/8 mpu 0b cburst 2623b/8 mpu 0b level 6
Sent 490496 bytes 479 pkts (dropped 0, overlimits 0)
rate 958bps
lended: 0 borrowed: 81 giants: 0
tokens: -62221 ctokens: 12800

class htb 1:12 parent 1:1 leaf 40: prio 0 quantum 6144 rate 480Kbit ceil 800Kbit burst 2213b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 239616 bytes 234 pkts (dropped 0, overlimits 0)
rate 426bps
lended: 234 borrowed: 0 giants: 0
tokens: 15867 ctokens: 12800

result for all line with 100kbps (pic5)

0.5 23947 23947 0 0 7982 7982 0 0 45228 45228 0 0 1.0 29036 29036 0 0 9571 9571 0 0 57118 57118 0 0 1.5 29318 29318 0 0 10107 10107 0 0 59489 59489 0 0 2.0 30522 30522 0 0 10253 10253 0 0 59327 59327 0 0 2.5 28197 28197 0 0 10280 10280 0 0 61159 61159 0 0 3.0 30910 30910 0 0 7927 7927 0 0 59985 59985 0 0 3.5 30991 30991 0 0 7935 7935 0 0 60665 60665 0 0 4.0 28994 28994 0 0 9598 9598 0 0 59183 59183 0 0 4.5 30150 30150 0 0 10034 10034 0 0 14044 14044 0 0 5.0 28662 28662 0 0 10458 10458 0 0 3333 3333 0 0 5.5 30876 30876 0 0 10506 10506 0 0 791 791 0 0 6.0 28540 28540 0 0 10523 10523 0 0 188 188 0 0 6.5 29107 29107 0 0 10154 10154 0 0 45 45 0 0 7.0 30387 30387 0 0 8500 8500 0 0 11 11 0 0 7.5 45085 45085 0 0 18230 18230 0 0 3 3 0 0 8.0 49523 49523 0 0 19855 19855 0 0 1 1 0 0 8.5 49546 49546 0 0 20405 20405 0 0 0 0 0 0 9.0 50916 50916 0 0 18643 18643 0 0 0 0 0 0 9.5 50410 50410 0 0 20082 20082 0 0 0 0 0 0 10.0 48597 48597 0 0 20453 20453 0 0 0 0 0 0

Quoted 5 lines · Martin Devera

What version of HTB do you use ? Send me
tc -s -d class show dev xxx
outoput after test pic5 generation.
devik

Quoted 38 lines
Quoted 35 lines · King Yung Tong

Thank you again for you help!
Attach is the pic5 for the ceil equal to 100kbps for all line.
pic10limit for the ceil equal to 100kbps except 1:20.

My objective is to show if not prio is set the excess should allocate according to rate. If the prio is set, the high prio should get more.

Quoted 21 lines · Martin Devera
Quoted 2 lines

Thank you for you answer, 1:10 is incresed but 1:20 is also increased and increase to the specific rate if I add 100kbps to every line.

sounds weird. With higher prio 1:10 should get 90k and 1:11 10k.

Quoted 3 lines

In my case, I would like to put all the extra to 1:10 only, is that means I have to give 1:11 ceil to 10kbps. If it is, is that means I don't need prio paramter? How prio parameter works?

your understanding is ok, tge ceil 10k is correct - the prio is meant for lowering delay and change in excess distribution is only "secondary" product.

Port the resulting graph somewhere so I can look at it.

devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#9 lore raw
In reply to King Yung Tong

Ok. It seems you generate only 40kbps by ethloop script. Then you can't expect your lines to go higher !
Generate 100kbps to 1:11 and 1:10 ...
devik

Quoted 70 lines · King Yung Tong

Here is the version and info.

Version htb3_2.4.17

[root@samwise htb]# ./tc -s -d class show dev lo
class htb 1:11 parent 1:2 leaf 30: prio 1 quantum 1024 rate 80Kbit ceil 800Kbit burst 1701b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 130048 bytes 127 pkts (dropped 0, overlimits 0)
rate 254bps
lended: 100 borrowed: 27 giants: 0
tokens: -60449 ctokens: 12800

class htb 1:1 root rate 800Kbit ceil 800Kbit burst 2623b/8 mpu 0b cburst 2623b/8 mpu 0b level 7 Sent 730112 bytes 713 pkts (dropped 0, overlimits
0)
rate 1426bps 1pps
lended: 81 borrowed: 0 giants: 0
tokens: 12800 ctokens: 12800

class htb 1:10 parent 1:2 leaf 20: prio 0 quantum 3072 rate 240Kbit ceil 800Kbit burst 1906b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 360448 bytes 352 pkts (dropped 0, overlimits 0)
rate 704bps
lended: 298 borrowed: 54 giants: 0
tokens: -36462 ctokens: 12800

class htb 1:2 parent 1:1 rate 320Kbit ceil 800Kbit burst 2008b/8 mpu 0b cburst 2623b/8 mpu 0b level 6
Sent 490496 bytes 479 pkts (dropped 0, overlimits 0)
rate 958bps
lended: 0 borrowed: 81 giants: 0
tokens: -62221 ctokens: 12800

class htb 1:12 parent 1:1 leaf 40: prio 0 quantum 6144 rate 480Kbit ceil 800Kbit burst 2213b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 239616 bytes 234 pkts (dropped 0, overlimits 0)
rate 426bps
lended: 234 borrowed: 0 giants: 0
tokens: 15867 ctokens: 12800

result for all line with 100kbps (pic5)

0.5 23947 23947 0 0 7982 7982 0 0 45228 45228 0 0 1.0 29036 29036 0 0 9571 9571 0 0 57118 57118 0 0 1.5 29318 29318 0 0 10107 10107 0 0 59489 59489 0 0 2.0 30522 30522 0 0 10253 10253 0 0 59327 59327 0 0 2.5 28197 28197 0 0 10280 10280 0 0 61159 61159 0 0 3.0 30910 30910 0 0 7927 7927 0 0 59985 59985 0 0 3.5 30991 30991 0 0 7935 7935 0 0 60665 60665 0 0 4.0 28994 28994 0 0 9598 9598 0 0 59183 59183 0 0 4.5 30150 30150 0 0 10034 10034 0 0 14044 14044 0 0 5.0 28662 28662 0 0 10458 10458 0 0 3333 3333 0 0 5.5 30876 30876 0 0 10506 10506 0 0 791 791 0 0 6.0 28540 28540 0 0 10523 10523 0 0 188 188 0 0 6.5 29107 29107 0 0 10154 10154 0 0 45 45 0 0 7.0 30387 30387 0 0 8500 8500 0 0 11 11 0 0 7.5 45085 45085 0 0 18230 18230 0 0 3 3 0 0 8.0 49523 49523 0 0 19855 19855 0 0 1 1 0 0 8.5 49546 49546 0 0 20405 20405 0 0 0 0 0 0 9.0 50916 50916 0 0 18643 18643 0 0 0 0 0 0 9.5 50410 50410 0 0 20082 20082 0 0 0 0 0 0 10.0 48597 48597 0 0 20453 20453 0 0 0 0 0 0

Quoted 48 lines
Quoted 43 lines · Martin Devera

What version of HTB do you use ? Send me
tc -s -d class show dev xxx
outoput after test pic5 generation.
devik

Quoted 35 lines · King Yung Tong

Thank you again for you help!
Attach is the pic5 for the ceil equal to 100kbps for all line.
pic10limit for the ceil equal to 100kbps except 1:20.

My objective is to show if not prio is set the excess should allocate according to rate. If the prio is set, the high prio should get more.

Quoted 21 lines · Martin Devera
Quoted 2 lines

Thank you for you answer, 1:10 is incresed but 1:20 is also increased and increase to the specific rate if I add 100kbps to every line.

sounds weird. With higher prio 1:10 should get 90k and 1:11 10k.

Quoted 3 lines

In my case, I would like to put all the extra to 1:10 only, is that means I have to give 1:11 ceil to 10kbps. If it is, is that means I don't need prio paramter? How prio parameter works?

your understanding is ok, tge ceil 10k is correct - the prio is meant for lowering delay and change in excess distribution is only "secondary" product.

Port the resulting graph somewhere so I can look at it.

devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#10 lore raw
In reply to King Yung Tong

Thank you, I put 100kbps to both 1:11 and 1:10. 1:10 (prio 0) get almost 50kbps form 60kbps excess and 1:20 (prio 1) get 10kbps form excess. Is it the expected result?
I gussess the all 60kbps (excess) should go to prio 0 or by proportional to rate in each class.

Pat

Quoted 126 lines · Martin Devera

Ok. It seems you generate only 40kbps by ethloop script. Then you can't expect your lines to go higher !
Generate 100kbps to 1:11 and 1:10 ...
devik

Quoted 70 lines · King Yung Tong

Here is the version and info.

Version htb3_2.4.17

[root@samwise htb]# ./tc -s -d class show dev lo
class htb 1:11 parent 1:2 leaf 30: prio 1 quantum 1024 rate 80Kbit ceil 800Kbit burst 1701b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 130048 bytes 127 pkts (dropped 0, overlimits 0)
rate 254bps
lended: 100 borrowed: 27 giants: 0
tokens: -60449 ctokens: 12800

class htb 1:1 root rate 800Kbit ceil 800Kbit burst 2623b/8 mpu 0b cburst 2623b/8 mpu 0b level 7 Sent 730112 bytes 713 pkts (dropped 0, overlimits
0)
rate 1426bps 1pps
lended: 81 borrowed: 0 giants: 0
tokens: 12800 ctokens: 12800

class htb 1:10 parent 1:2 leaf 20: prio 0 quantum 3072 rate 240Kbit ceil 800Kbit burst 1906b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 360448 bytes 352 pkts (dropped 0, overlimits 0)
rate 704bps
lended: 298 borrowed: 54 giants: 0
tokens: -36462 ctokens: 12800

class htb 1:2 parent 1:1 rate 320Kbit ceil 800Kbit burst 2008b/8 mpu 0b cburst 2623b/8 mpu 0b level 6
Sent 490496 bytes 479 pkts (dropped 0, overlimits 0)
rate 958bps
lended: 0 borrowed: 81 giants: 0
tokens: -62221 ctokens: 12800

class htb 1:12 parent 1:1 leaf 40: prio 0 quantum 6144 rate 480Kbit ceil 800Kbit burst 2213b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 239616 bytes 234 pkts (dropped 0, overlimits 0)
rate 426bps
lended: 234 borrowed: 0 giants: 0
tokens: 15867 ctokens: 12800

result for all line with 100kbps (pic5)

0.5 23947 23947 0 0 7982 7982 0 0 45228 45228 0 0 1.0 29036 29036 0 0 9571 9571 0 0 57118 57118 0 0 1.5 29318 29318 0 0 10107 10107 0 0 59489 59489 0 0 2.0 30522 30522 0 0 10253 10253 0 0 59327 59327 0 0 2.5 28197 28197 0 0 10280 10280 0 0 61159 61159 0 0 3.0 30910 30910 0 0 7927 7927 0 0 59985 59985 0 0 3.5 30991 30991 0 0 7935 7935 0 0 60665 60665 0 0 4.0 28994 28994 0 0 9598 9598 0 0 59183 59183 0 0 4.5 30150 30150 0 0 10034 10034 0 0 14044 14044 0 0 5.0 28662 28662 0 0 10458 10458 0 0 3333 3333 0 0 5.5 30876 30876 0 0 10506 10506 0 0 791 791 0 0 6.0 28540 28540 0 0 10523 10523 0 0 188 188 0 0 6.5 29107 29107 0 0 10154 10154 0 0 45 45 0 0 7.0 30387 30387 0 0 8500 8500 0 0 11 11 0 0 7.5 45085 45085 0 0 18230 18230 0 0 3 3 0 0 8.0 49523 49523 0 0 19855 19855 0 0 1 1 0 0 8.5 49546 49546 0 0 20405 20405 0 0 0 0 0 0 9.0 50916 50916 0 0 18643 18643 0 0 0 0 0 0 9.5 50410 50410 0 0 20082 20082 0 0 0 0 0 0 10.0 48597 48597 0 0 20453 20453 0 0 0 0 0 0

Quoted 48 lines
Quoted 43 lines · Martin Devera

What version of HTB do you use ? Send me
tc -s -d class show dev xxx
outoput after test pic5 generation.
devik

Quoted 35 lines · King Yung Tong

Thank you again for you help!
Attach is the pic5 for the ceil equal to 100kbps for all line.
pic10limit for the ceil equal to 100kbps except 1:20.

My objective is to show if not prio is set the excess should allocate according to rate. If the prio is set, the high prio should get more.

Quoted 21 lines · Martin Devera
Quoted 2 lines

Thank you for you answer, 1:10 is incresed but 1:20 is also increased and increase to the specific rate if I add 100kbps to every line.

sounds weird. With higher prio 1:10 should get 90k and 1:11 10k.

Quoted 3 lines

In my case, I would like to put all the extra to 1:10 only, is that means I have to give 1:11 ceil to 10kbps. If it is, is that means I don't need prio paramter? How prio parameter works?

your understanding is ok, tge ceil 10k is correct - the prio is meant for lowering delay and change in excess distribution is only "secondary" product.

Port the resulting graph somewhere so I can look at it.

devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Quoted 4 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#11 lore raw
In reply to King Yung Tong

ethloop output (as text)

Quoted 7 lines · King Yung Tong

Thank you, I put 100kbps to both 1:11 and 1:10. 1:10 (prio 0) get almost 50kbps form 60kbps excess and 1:20 (prio 1) get 10kbps form excess. Is it the expected result?
I gussess the all 60kbps (excess) should go to prio 0 or by proportional to rate in each class.

Quoted 137 lines

Pat

Quoted 130 lines · Martin Devera

Ok. It seems you generate only 40kbps by ethloop script. Then you can't expect your lines to go higher !
Generate 100kbps to 1:11 and 1:10 ...
devik

Quoted 70 lines · King Yung Tong

Here is the version and info.

Version htb3_2.4.17

[root@samwise htb]# ./tc -s -d class show dev lo
class htb 1:11 parent 1:2 leaf 30: prio 1 quantum 1024 rate 80Kbit ceil 800Kbit burst 1701b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 130048 bytes 127 pkts (dropped 0, overlimits 0)
rate 254bps
lended: 100 borrowed: 27 giants: 0
tokens: -60449 ctokens: 12800

class htb 1:1 root rate 800Kbit ceil 800Kbit burst 2623b/8 mpu 0b cburst 2623b/8 mpu 0b level 7 Sent 730112 bytes 713 pkts (dropped 0, overlimits
0)
rate 1426bps 1pps
lended: 81 borrowed: 0 giants: 0
tokens: 12800 ctokens: 12800

class htb 1:10 parent 1:2 leaf 20: prio 0 quantum 3072 rate 240Kbit ceil 800Kbit burst 1906b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 360448 bytes 352 pkts (dropped 0, overlimits 0)
rate 704bps
lended: 298 borrowed: 54 giants: 0
tokens: -36462 ctokens: 12800

class htb 1:2 parent 1:1 rate 320Kbit ceil 800Kbit burst 2008b/8 mpu 0b cburst 2623b/8 mpu 0b level 6
Sent 490496 bytes 479 pkts (dropped 0, overlimits 0)
rate 958bps
lended: 0 borrowed: 81 giants: 0
tokens: -62221 ctokens: 12800

class htb 1:12 parent 1:1 leaf 40: prio 0 quantum 6144 rate 480Kbit ceil 800Kbit burst 2213b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 239616 bytes 234 pkts (dropped 0, overlimits 0)
rate 426bps
lended: 234 borrowed: 0 giants: 0
tokens: 15867 ctokens: 12800

result for all line with 100kbps (pic5)

0.5 23947 23947 0 0 7982 7982 0 0 45228 45228 0 0 1.0 29036 29036 0 0 9571 9571 0 0 57118 57118 0 0 1.5 29318 29318 0 0 10107 10107 0 0 59489 59489 0 0 2.0 30522 30522 0 0 10253 10253 0 0 59327 59327 0 0 2.5 28197 28197 0 0 10280 10280 0 0 61159 61159 0 0 3.0 30910 30910 0 0 7927 7927 0 0 59985 59985 0 0 3.5 30991 30991 0 0 7935 7935 0 0 60665 60665 0 0 4.0 28994 28994 0 0 9598 9598 0 0 59183 59183 0 0 4.5 30150 30150 0 0 10034 10034 0 0 14044 14044 0 0 5.0 28662 28662 0 0 10458 10458 0 0 3333 3333 0 0 5.5 30876 30876 0 0 10506 10506 0 0 791 791 0 0 6.0 28540 28540 0 0 10523 10523 0 0 188 188 0 0 6.5 29107 29107 0 0 10154 10154 0 0 45 45 0 0 7.0 30387 30387 0 0 8500 8500 0 0 11 11 0 0 7.5 45085 45085 0 0 18230 18230 0 0 3 3 0 0 8.0 49523 49523 0 0 19855 19855 0 0 1 1 0 0 8.5 49546 49546 0 0 20405 20405 0 0 0 0 0 0 9.0 50916 50916 0 0 18643 18643 0 0 0 0 0 0 9.5 50410 50410 0 0 20082 20082 0 0 0 0 0 0 10.0 48597 48597 0 0 20453 20453 0 0 0 0 0 0

Quoted 48 lines
Quoted 43 lines · Martin Devera

What version of HTB do you use ? Send me
tc -s -d class show dev xxx
outoput after test pic5 generation.
devik

Quoted 35 lines · King Yung Tong

Thank you again for you help!
Attach is the pic5 for the ceil equal to 100kbps for all line.
pic10limit for the ceil equal to 100kbps except 1:20.

My objective is to show if not prio is set the excess should allocate according to rate. If the prio is set, the high prio should get more.

Quoted 21 lines · Martin Devera
Quoted 2 lines

Thank you for you answer, 1:10 is incresed but 1:20 is also increased and increase to the specific rate if I add 100kbps to every line.

sounds weird. With higher prio 1:10 should get 90k and 1:11 10k.

Quoted 3 lines

In my case, I would like to put all the extra to 1:10 only, is that means I have to give 1:11 ceil to 10kbps. If it is, is that means I don't need prio paramter? How prio parameter works?

your understanding is ok, tge ceil 10k is correct - the prio is meant for lowering delay and change in excess distribution is only "secondary" product.

Port the resulting graph somewhere so I can look at it.

devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#12 lore raw
In reply to King Yung Tong

Thank you, I put 100kbps to both 1:11 and 1:10. 1:10 (prio 0) get almost 50kbps form 60kbps excess and 1:20 (prio 1) get 10kbps form excess. Is it the expected result?
I gussess the all 60kbps (excess) should go to prio 0 or by proportional to rate in each class. The rate on the original class is 1:3. ./tc class add dev lo parent 1:2 classid 1:10 htb rate 30kbps ceil 100kbps prio 0
./tc class add dev lo parent 1:2 classid 1:11 htb rate 10kbps ceil 100kbps prio 1

0.5 23490 23490 0 0 7830 7830 0 0 46202 46202 0 0
1.0 29308 29308 0 0 9471 9471 0 0 57537 57537 0 0
1.5 30066 30066 0 0 10311 10311 0 0 58370 58370 0 0
2.0 30364 30364 0 0 10190 10190 0 0 59133 59133 0 0
2.5 28144 28144 0 0 10251 10251 0 0 61029 61029 0 0
3.0 30859 30859 0 0 7907 7907 0 0 59899 59899 0 0
3.5 30563 30563 0 0 8694 8694 0 0 60245 60245 0 0
4.0 29243 29243 0 0 9873 9873 0 0 58596 58596 0 0
4.5 83553 74535 30 0 78956 16722 205 0 13905 13905 $5.0 97047 89562 20 0 95957 10635 438 0 3300 3300 0 05.5 100414 88939 38 0 100155 13212 553 0 783 783 0 06.0 101170 92980 20 0 101108 9802 570 0 186 186 0 0 6.5 98639 89751 38 0 98624 13015 577 0 44 44 0 0
7.0 99815 93172 20 0 99812 9755 578 0 10 10 0 0
7.5 63232 65056 0 0 39204 23397 41 0 3 3 0 0
8.0 54142 54575 0 0 22722 18971 3 0 1 1 0 0
8.5 51258 51361 0 0 21080 20189 0 0 0 0 0 0
9.0 50674 50698 0 0 20406 20195 0 0 0 0 0 0
9.5 49723 49729 0 0 20402 20351 0 0 0 0 0 0
10.0 51020 51021 0 0 20529 20517 0 0 0 0 0 0

Quoted 144 lines · Martin Devera

ethloop output (as text)

Quoted 139 lines · King Yung Tong

Pat

Quoted 130 lines · Martin Devera

Ok. It seems you generate only 40kbps by ethloop script. Then you can't expect your lines to go higher !
Generate 100kbps to 1:11 and 1:10 ...
devik

Quoted 70 lines · King Yung Tong

Here is the version and info.

Version htb3_2.4.17

[root@samwise htb]# ./tc -s -d class show dev lo
class htb 1:11 parent 1:2 leaf 30: prio 1 quantum 1024 rate 80Kbit ceil 800Kbit burst 1701b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 130048 bytes 127 pkts (dropped 0, overlimits 0)
rate 254bps
lended: 100 borrowed: 27 giants: 0
tokens: -60449 ctokens: 12800

class htb 1:1 root rate 800Kbit ceil 800Kbit burst 2623b/8 mpu 0b cburst 2623b/8 mpu 0b level 7 Sent 730112 bytes 713 pkts (dropped 0, overlimits
0)
rate 1426bps 1pps
lended: 81 borrowed: 0 giants: 0
tokens: 12800 ctokens: 12800

class htb 1:10 parent 1:2 leaf 20: prio 0 quantum 3072 rate 240Kbit ceil 800Kbit burst 1906b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 360448 bytes 352 pkts (dropped 0, overlimits 0)
rate 704bps
lended: 298 borrowed: 54 giants: 0
tokens: -36462 ctokens: 12800

class htb 1:2 parent 1:1 rate 320Kbit ceil 800Kbit burst 2008b/8 mpu 0b cburst 2623b/8 mpu 0b level 6
Sent 490496 bytes 479 pkts (dropped 0, overlimits 0)
rate 958bps
lended: 0 borrowed: 81 giants: 0
tokens: -62221 ctokens: 12800

class htb 1:12 parent 1:1 leaf 40: prio 0 quantum 6144 rate 480Kbit ceil 800Kbit burst 2213b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 239616 bytes 234 pkts (dropped 0, overlimits 0)
rate 426bps
lended: 234 borrowed: 0 giants: 0
tokens: 15867 ctokens: 12800

result for all line with 100kbps (pic5)

0.5 23947 23947 0 0 7982 7982 0 0 45228 45228 0 0 1.0 29036 29036 0 0 9571 9571 0 0 57118 57118 0 0 1.5 29318 29318 0 0 10107 10107 0 0 59489 59489 0 0 2.0 30522 30522 0 0 10253 10253 0 0 59327 59327 0 0 2.5 28197 28197 0 0 10280 10280 0 0 61159 61159 0 0 3.0 30910 30910 0 0 7927 7927 0 0 59985 59985 0 0 3.5 30991 30991 0 0 7935 7935 0 0 60665 60665 0 0 4.0 28994 28994 0 0 9598 9598 0 0 59183 59183 0 0 4.5 30150 30150 0 0 10034 10034 0 0 14044 14044 0 0 5.0 28662 28662 0 0 10458 10458 0 0 3333 3333 0 0 5.5 30876 30876 0 0 10506 10506 0 0 791 791 0 0 6.0 28540 28540 0 0 10523 10523 0 0 188 188 0 0 6.5 29107 29107 0 0 10154 10154 0 0 45 45 0 0 7.0 30387 30387 0 0 8500 8500 0 0 11 11 0 0 7.5 45085 45085 0 0 18230 18230 0 0 3 3 0 0 8.0 49523 49523 0 0 19855 19855 0 0 1 1 0 0 8.5 49546 49546 0 0 20405 20405 0 0 0 0 0 0 9.0 50916 50916 0 0 18643 18643 0 0 0 0 0 0 9.5 50410 50410 0 0 20082 20082 0 0 0 0 0 0 10.0 48597 48597 0 0 20453 20453 0 0 0 0 0 0

Quoted 48 lines
Quoted 43 lines · Martin Devera

What version of HTB do you use ? Send me
tc -s -d class show dev xxx
outoput after test pic5 generation.
devik

Quoted 35 lines · King Yung Tong

Thank you again for you help!
Attach is the pic5 for the ceil equal to 100kbps for all line.
pic10limit for the ceil equal to 100kbps except 1:20.

My objective is to show if not prio is set the excess should allocate according to rate. If the prio is set, the high prio should get more.

Quoted 21 lines · Martin Devera
Quoted 2 lines

Thank you for you answer, 1:10 is incresed but 1:20 is also increased and increase to the specific rate if I add 100kbps to every line.

sounds weird. With higher prio 1:10 should get 90k and 1:11 10k.

Quoted 3 lines

In my case, I would like to put all the extra to 1:10 only, is that means I have to give 1:11 ceil to 10kbps. If it is, is that means I don't need prio paramter? How prio parameter works?

your understanding is ok, tge ceil 10k is correct - the prio is meant for lowering delay and change in excess distribution is only "secondary" product.

Port the resulting graph somewhere so I can look at it.

devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Quoted 4 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#13 lore raw
In reply to King Yung Tong
Quoted 3 lines

6.0 101170 92980 20 0 101108 9802 570 0 186 186 0 0 6.5 98639 89751 38 0 98624 13015 577 0 44 44 0 0 7.0 99815 93172 20 0 99812 9755 578 0 10 10 0 0

here it is exacly what you want

7.5 63232 65056 0 0 39204 23397 41 0 3 3 0 0

Quoted 5 lines

8.0 54142 54575 0 0 22722 18971 3 0 1 1 0 0 8.5 51258 51361 0 0 21080 20189 0 0 0 0 0 0 9.0 50674 50698 0 0 20406 20195 0 0 0 0 0 0 9.5 49723 49729 0 0 20402 20351 0 0 0 0 0 0 10.0 51020 51021 0 0 20529 20517 0 0 0 0 0 0

end here generated rate seems to be 50k not 100 ! seems you need to repair other line in your ethloop script

Quoted 148 lines · Martin Devera
Quoted 145 lines

ethloop output (as text)

Quoted 139 lines · King Yung Tong

Pat

Quoted 130 lines · Martin Devera

Ok. It seems you generate only 40kbps by ethloop script. Then you can't expect your lines to go higher !
Generate 100kbps to 1:11 and 1:10 ...
devik

Quoted 70 lines · King Yung Tong

Here is the version and info.

Version htb3_2.4.17

[root@samwise htb]# ./tc -s -d class show dev lo
class htb 1:11 parent 1:2 leaf 30: prio 1 quantum 1024 rate 80Kbit ceil 800Kbit burst 1701b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 130048 bytes 127 pkts (dropped 0, overlimits 0)
rate 254bps
lended: 100 borrowed: 27 giants: 0
tokens: -60449 ctokens: 12800

class htb 1:1 root rate 800Kbit ceil 800Kbit burst 2623b/8 mpu 0b cburst 2623b/8 mpu 0b level 7 Sent 730112 bytes 713 pkts (dropped 0, overlimits
0)
rate 1426bps 1pps
lended: 81 borrowed: 0 giants: 0
tokens: 12800 ctokens: 12800

class htb 1:10 parent 1:2 leaf 20: prio 0 quantum 3072 rate 240Kbit ceil 800Kbit burst 1906b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 360448 bytes 352 pkts (dropped 0, overlimits 0)
rate 704bps
lended: 298 borrowed: 54 giants: 0
tokens: -36462 ctokens: 12800

class htb 1:2 parent 1:1 rate 320Kbit ceil 800Kbit burst 2008b/8 mpu 0b cburst 2623b/8 mpu 0b level 6
Sent 490496 bytes 479 pkts (dropped 0, overlimits 0)
rate 958bps
lended: 0 borrowed: 81 giants: 0
tokens: -62221 ctokens: 12800

class htb 1:12 parent 1:1 leaf 40: prio 0 quantum 6144 rate 480Kbit ceil 800Kbit burst 2213b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 239616 bytes 234 pkts (dropped 0, overlimits 0)
rate 426bps
lended: 234 borrowed: 0 giants: 0
tokens: 15867 ctokens: 12800

result for all line with 100kbps (pic5)

0.5 23947 23947 0 0 7982 7982 0 0 45228 45228 0 0 1.0 29036 29036 0 0 9571 9571 0 0 57118 57118 0 0 1.5 29318 29318 0 0 10107 10107 0 0 59489 59489 0 0 2.0 30522 30522 0 0 10253 10253 0 0 59327 59327 0 0 2.5 28197 28197 0 0 10280 10280 0 0 61159 61159 0 0 3.0 30910 30910 0 0 7927 7927 0 0 59985 59985 0 0 3.5 30991 30991 0 0 7935 7935 0 0 60665 60665 0 0 4.0 28994 28994 0 0 9598 9598 0 0 59183 59183 0 0 4.5 30150 30150 0 0 10034 10034 0 0 14044 14044 0 0 5.0 28662 28662 0 0 10458 10458 0 0 3333 3333 0 0 5.5 30876 30876 0 0 10506 10506 0 0 791 791 0 0 6.0 28540 28540 0 0 10523 10523 0 0 188 188 0 0 6.5 29107 29107 0 0 10154 10154 0 0 45 45 0 0 7.0 30387 30387 0 0 8500 8500 0 0 11 11 0 0 7.5 45085 45085 0 0 18230 18230 0 0 3 3 0 0 8.0 49523 49523 0 0 19855 19855 0 0 1 1 0 0 8.5 49546 49546 0 0 20405 20405 0 0 0 0 0 0 9.0 50916 50916 0 0 18643 18643 0 0 0 0 0 0 9.5 50410 50410 0 0 20082 20082 0 0 0 0 0 0 10.0 48597 48597 0 0 20453 20453 0 0 0 0 0 0

Quoted 48 lines
Quoted 43 lines · Martin Devera

What version of HTB do you use ? Send me
tc -s -d class show dev xxx
outoput after test pic5 generation.
devik

Quoted 35 lines · King Yung Tong

Thank you again for you help!
Attach is the pic5 for the ceil equal to 100kbps for all line.
pic10limit for the ceil equal to 100kbps except 1:20.

My objective is to show if not prio is set the excess should allocate according to rate. If the prio is set, the high prio should get more.

Quoted 21 lines · Martin Devera
Quoted 2 lines

Thank you for you answer, 1:10 is incresed but 1:20 is also increased and increase to the specific rate if I add 100kbps to every line.

sounds weird. With higher prio 1:10 should get 90k and 1:11 10k.

Quoted 3 lines

In my case, I would like to put all the extra to 1:10 only, is that means I have to give 1:11 ceil to 10kbps. If it is, is that means I don't need prio paramter? How prio parameter works?

your understanding is ok, tge ceil 10k is correct - the prio is meant for lowering delay and change in excess distribution is only "secondary" product.

Port the resulting graph somewhere so I can look at it.

devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Quoted 10 lines
Quoted 4 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#14 lore raw
In reply to King Yung Tong

It is working. Thank you. I really appreciate your help. :) Thank you!!!!!!!!!!

Pat

Quoted 7 lines · Martin Devera
Quoted 3 lines

6.0 101170 92980 20 0 101108 9802 570 0 186 186 0 0 6.5 98639 89751 38 0 98624 13015 577 0 44 44 0 0 7.0 99815 93172 20 0 99812 9755 578 0 10 10 0 0

here it is exacly what you want

7.5 63232 65056 0 0 39204 23397 41 0 3 3 0 0

Quoted 168 lines
Quoted 5 lines

8.0 54142 54575 0 0 22722 18971 3 0 1 1 0 0 8.5 51258 51361 0 0 21080 20189 0 0 0 0 0 0 9.0 50674 50698 0 0 20406 20195 0 0 0 0 0 0 9.5 49723 49729 0 0 20402 20351 0 0 0 0 0 0 10.0 51020 51021 0 0 20529 20517 0 0 0 0 0 0

end here generated rate seems to be 50k not 100 ! seems you need to repair other line in your ethloop script

Quoted 158 lines · Martin Devera
Quoted 145 lines

ethloop output (as text)

Quoted 139 lines · King Yung Tong

Pat

Quoted 130 lines · Martin Devera

Ok. It seems you generate only 40kbps by ethloop script. Then you can't expect your lines to go higher !
Generate 100kbps to 1:11 and 1:10 ...
devik

Quoted 70 lines · King Yung Tong

Here is the version and info.

Version htb3_2.4.17

[root@samwise htb]# ./tc -s -d class show dev lo
class htb 1:11 parent 1:2 leaf 30: prio 1 quantum 1024 rate 80Kbit ceil 800Kbit burst 1701b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 130048 bytes 127 pkts (dropped 0, overlimits 0)
rate 254bps
lended: 100 borrowed: 27 giants: 0
tokens: -60449 ctokens: 12800

class htb 1:1 root rate 800Kbit ceil 800Kbit burst 2623b/8 mpu 0b cburst 2623b/8 mpu 0b level 7 Sent 730112 bytes 713 pkts (dropped 0, overlimits
0)
rate 1426bps 1pps
lended: 81 borrowed: 0 giants: 0
tokens: 12800 ctokens: 12800

class htb 1:10 parent 1:2 leaf 20: prio 0 quantum 3072 rate 240Kbit ceil 800Kbit burst 1906b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 360448 bytes 352 pkts (dropped 0, overlimits 0)
rate 704bps
lended: 298 borrowed: 54 giants: 0
tokens: -36462 ctokens: 12800

class htb 1:2 parent 1:1 rate 320Kbit ceil 800Kbit burst 2008b/8 mpu 0b cburst 2623b/8 mpu 0b level 6
Sent 490496 bytes 479 pkts (dropped 0, overlimits 0)
rate 958bps
lended: 0 borrowed: 81 giants: 0
tokens: -62221 ctokens: 12800

class htb 1:12 parent 1:1 leaf 40: prio 0 quantum 6144 rate 480Kbit ceil 800Kbit burst 2213b/8 mpu 0b cburst 2623b/8 mpu 0b level 0
Sent 239616 bytes 234 pkts (dropped 0, overlimits 0)
rate 426bps
lended: 234 borrowed: 0 giants: 0
tokens: 15867 ctokens: 12800

result for all line with 100kbps (pic5)

0.5 23947 23947 0 0 7982 7982 0 0 45228 45228 0 0 1.0 29036 29036 0 0 9571 9571 0 0 57118 57118 0 0 1.5 29318 29318 0 0 10107 10107 0 0 59489 59489 0 0 2.0 30522 30522 0 0 10253 10253 0 0 59327 59327 0 0 2.5 28197 28197 0 0 10280 10280 0 0 61159 61159 0 0 3.0 30910 30910 0 0 7927 7927 0 0 59985 59985 0 0 3.5 30991 30991 0 0 7935 7935 0 0 60665 60665 0 0 4.0 28994 28994 0 0 9598 9598 0 0 59183 59183 0 0 4.5 30150 30150 0 0 10034 10034 0 0 14044 14044 0 0 5.0 28662 28662 0 0 10458 10458 0 0 3333 3333 0 0 5.5 30876 30876 0 0 10506 10506 0 0 791 791 0 0 6.0 28540 28540 0 0 10523 10523 0 0 188 188 0 0 6.5 29107 29107 0 0 10154 10154 0 0 45 45 0 0 7.0 30387 30387 0 0 8500 8500 0 0 11 11 0 0 7.5 45085 45085 0 0 18230 18230 0 0 3 3 0 0 8.0 49523 49523 0 0 19855 19855 0 0 1 1 0 0 8.5 49546 49546 0 0 20405 20405 0 0 0 0 0 0 9.0 50916 50916 0 0 18643 18643 0 0 0 0 0 0 9.5 50410 50410 0 0 20082 20082 0 0 0 0 0 0 10.0 48597 48597 0 0 20453 20453 0 0 0 0 0 0

Quoted 48 lines
Quoted 43 lines · Martin Devera

What version of HTB do you use ? Send me
tc -s -d class show dev xxx
outoput after test pic5 generation.
devik

Quoted 35 lines · King Yung Tong

Thank you again for you help!
Attach is the pic5 for the ceil equal to 100kbps for all line.
pic10limit for the ceil equal to 100kbps except 1:20.

My objective is to show if not prio is set the excess should allocate according to rate. If the prio is set, the high prio should get more.

Quoted 21 lines · Martin Devera
Quoted 2 lines

Thank you for you answer, 1:10 is incresed but 1:20 is also increased and increase to the specific rate if I add 100kbps to every line.

sounds weird. With higher prio 1:10 should get 90k and 1:11 10k.

Quoted 3 lines

In my case, I would like to put all the extra to 1:10 only, is that means I have to give 1:11 ceil to 10kbps. If it is, is that means I don't need prio paramter? How prio parameter works?

your understanding is ok, tge ceil 10k is correct - the prio is meant for lowering delay and change in excess distribution is only "secondary" product.

Port the resulting graph somewhere so I can look at it.

devik

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

Quoted 4 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/