GRED queues in Diffserv
Hi all,
I am setting up a Diffserv router. Part of the script that I use it as follows:
---------------------------------------------------
sudo /usr/bin/tc qdisc add dev r1p4 handle 1:0 root dsmark indices 64 set_tc_index
sudo /usr/bin/tc filter add dev r1p4 parent 1:0 protocol ip prio 1 tcindex mask 0xfc shift 2 pass_on
sudo /usr/bin/tc qdisc add dev r1p4 parent 1:0 handle 2:0 cbq bandwidth 10Mbit allot 1514 cell 8 avpkt 1456 mpu 64
sudo /usr/bin/tc filter add dev r1p4 parent 2:0 protocol ip prio 1 tcindex mask 0xf0 shift 4 pass_on
sudo /usr/bin/tc class add dev r1p4 parent 2:0 classid 2:1 cbq bandwidth 10Mbit rate 6Mbit avpkt 1456 prio 5 bounded allot 1514 weight 600Kbit maxburst 21
sudo /usr/bin/tc filter add dev r1p4 parent 2:0 protocol ip prio 1 handle 1 tcindex classid 2:1
sudo /usr/bin/tc qdisc add dev r1p4 parent 2:1 gred setup DPs 3 default 2 grio
---------------------------------------------------
This last line where I setup the gred qdisc shows a message in the logs as "NO GRED Queues setup! ". Can anybody comment on what this could mean? I am using 2.2.18 with a Diffserv patch.
TIA,
Amit
PS.The remainin lines of the script include creating 3 gred qdiscs, setting their limits and creating another CBQ class (2:2) for un(ds)marked traffic.
Signature · 13 lines
I'm an angel!!! Honest!
The horns are just there to hold the halo up straight.
^-^-^-^-^-^-^-^-^-^-^-^-^-^-^-^-^-^-^-^-^-^-^-^-^-^-^
Amit Kucheria
EECS Grad. Research Assistant
University of Kansas @ Lawrence
(R): +1-785-830-8521 ||| (C): +1-785-760-2871
____________________________________________________
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/Hi Amit,
Quoted 8 lines · Amit Kucheria
sudo
/usr/bin/tcqdisc add dev r1p4 parent 2:1 gred setup DPs 3 default 2 grio
---------------------------------------------------This last line where I setup the gred qdisc shows a message in the logs as "NO GRED Queues setup! ". Can anybody comment on what this could mean? I am using 2.2.18 with a Diffserv patch.
Quoted 6 lines
TIA,
AmitPS.The remainin lines of the script include creating 3 gred qdiscs, setting their limits and creating another CBQ class (2:2) for un(ds)marked traffic.
Same thing here. I looked into sch_gred.c and it looks like gred complains about the lack of DP entries in the table as soon as you issue the gred setup command. I didn't succeed in defining the virtual queues before I issue the gred setup command, so I decided to live with the log message.
Perhaps there is a better way to do it, but honestly I doubt it - and, hey, Almesberger uses the same approach in his tcng example script, so at least it can't be complete nonsense. :)
Kurt
P.S.: attached is my way of doing it - produces the log message, but works...
#!/bin/sh
#
# author: Kurt Wagner, [email protected]
# last changed: 25.04.02 # # Script to setup GRED # # Gred uses the 4 least sig. bits of skb->tc_index to map packets to # virtual queues (DP, which stands for drop precedence). This script # setups 4 virtual queues, packets with tc_index = 0x01 are mapped # to DP1, 0x02 to DP2 and so on. # # The ECN bits (least sig. 2 bits of DS field) are masked out and # most apps are only able to set a value for the whole DS field (if # at all), so be carefull which DS field values you choose. # # e.g.: # # | DS field | tc_index | DP | # +----------+----------+----+ # | 0x04 | 0x01 | 1 | # | 0x08 | 0x02 | 2 | # | 0x0C | 0x03 | 3 | # | 0x10 | 0x04 | 4 | #
DEV="eth1"
function usage
{
echo "Usage:" basename $0 "COMMAND"
echo "where COMMAND := { start | stop | status }" exit 1
}
if [ $# = 0 ]; then usage ; fi
case "$1" in
start)
# add the dsmarker as root and copys DS field to skb->tc_index tc qdisc add dev $DEV handle 1:0 root dsmark indices 4 set_tc_index # mask out ECN bits and shift right by 2 to extract DSCP tc filter add dev $DEV parent 1:0 protocol ip prio 1 \ tcindex mask 0xfc shift 2
# general gred setup, 4 queues, nr 4 is the default queue, 'grio' says # we use the RIO like multi-RED behavior to calculate the average queue # lengths tc qdisc add dev $DEV parent 1:0 handle 2:0 \ gred setup DPs 4 default 4 grio
# setup virtuall queues, priority 1 is the highest
tc qdisc change dev $DEV handle 2:0 gred limit 200KB min 15KB max 45KB \ burst 20 avpkt 1000 bandwidth 10Mbit probability 0.02 DP 1 prio 1 tc qdisc change dev $DEV handle 2:0 gred limit 200KB min 15KB max 45KB \ burst 20 avpkt 1000 bandwidth 10Mbit probability 0.02 DP 2 prio 2 tc qdisc change dev $DEV handle 2:0 gred limit 200KB min 15KB max 45KB \ burst 20 avpkt 1000 bandwidth 10Mbit probability 0.02 DP 3 prio 3 tc qdisc change dev $DEV handle 2:0 gred limit 200KB min 15KB max 45KB \ burst 20 avpkt 1000 bandwidth 10Mbit probability 0.2 DP 4 prio 4
echo -e "basename $0 enabled \n"
;;
stop)
tc qdisc del dev $DEV root
echo -e "basename $0 disabled \n"
;;
status)
tc -s -s -s qdisc ls dev $DEV
;;
*)
usage
;;
esac
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/