Skip to contentSkip to conversation

I can not set up filters

LARTC Gabriel Paues 3 participants 5 messages Jul 3, 2002

lore
Share & tools
lore
#0 lore raw

Hello!

I have set up a htb qdisc:

# tc qdisc show dev eth1
qdisc htb 1: r2q 10 default 12 direct_packets_stat 0

with the following classes attached to it

#tc class show dev eth1
class htb 1:11 parent 1:1 prio 0 rate 80Kbit ceil 800Kbit burst 1575b cburst 1969b
class htb 1:1 root rate 800Kbit ceil 800Kbit burst 1969b cburst 1969b class htb 1:10 parent 1:1 prio 0 rate 240Kbit ceil 800Kbit burst 1772b cburst 1969b
class htb 1:12 parent 1:1 prio 0 rate 480Kbit ceil 800Kbit burst 1181b cburst 1969b

When I try to attach filters to it i get the following answer:

# tc filter add dev eth1 protocol ip parent 1:0 prio 1 u32 match ip
dport 80 0xffff flowid 1:10
RTNETLINK answers: Invalid argument

What am I doing wrong?

I Would really appreciate your help.

Regards,

Gabriel Paues
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Gabriel Paues

Wohhaaa...

Thank you so much for pointing out the obvious...
Now it works..

Thanks!

Gabriel Paues

Quoted 9 lines · Martin Devera
Quoted 7 lines

When I try to attach filters to it i get the following answer:

# tc filter add dev eth1 protocol ip parent 1:0 prio 1 u32 match ip
dport 80 0xffff flowid 1:10
RTNETLINK answers: Invalid argument

What am I doing wrong?

did you load/compile U32 classifier ?

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to Gabriel Paues

Hi,

Quoted 13 lines

qdisc htb 1: r2q 10 default 12 direct_packets_stat 0

with the following classes attached to it

#tc class show dev eth1
class htb 1:11 parent 1:1 prio 0 rate 80Kbit ceil 800Kbit burst 1575b cburst 1969b
class htb 1:1 root rate 800Kbit ceil 800Kbit burst 1969b cburst 1969b class htb 1:10 parent 1:1 prio 0 rate 240Kbit ceil 800Kbit burst 1772b cburst 1969b
class htb 1:12 parent 1:1 prio 0 rate 480Kbit ceil 800Kbit burst 1181b cburst 1969b

Quoted 6 lines

When I try to attach filters to it i get the following answer:

# tc filter add dev eth1 protocol ip parent 1:0 prio 1 u32 match ip
dport 80 0xffff flowid 1:10
RTNETLINK answers: Invalid argument

What am I doing wrong?

My guess:

You try to attach the filter to the class 1:0. Try attaching it to the defined root class 1:1, or even better to the subclasses 1:10, 1:11 or 1:12 (think this is what you want).

Greetings,
Bjoern

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/