Skip to contentSkip to conversation

which NIC is which

LARTC John Telford 5 participants 7 messages Jul 9, 2002 – Jul 10, 2002

lore
Share & tools
lore
#0 lore raw

I'm building routers. It's difficult to tell in advance which NIC will be assigned eth0 and which will assigned eth1 when using two NICs. Ping testing usually clears up this simple problem.

The identification problem gets worse when adding a third NIC, after sorting out the first two NICs. Frequently the eth0 or eth1 assignments for the first two NICs change.

Of course adding a fourth and fifth NIC multiplies the identification problem. Yes, some of my routers are supporting five network segments.

My question is, what's the algorithm for assigning Ethernet designations? I know it not placement order in the PCI bus, and I know its not the NIC data-link address.

So what is it?

Thanks ...John

Signature · 8 lines
John Telford - Owner
JohnTelford.com LLC
503-292-6865 - fax:503-292-3094
[email protected] - www.johntelford.com

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw
Quoted 8 lines · John Telford

I'm building routers. It's difficult to tell in advance which NIC will be assigned eth0 and which will assigned eth1 when using two NICs. Ping testing usually clears up this simple problem.

The identification problem gets worse when adding a third NIC, after sorting out the first two NICs. Frequently the eth0 or eth1 assignments for the first two NICs change.

Quoted 8 lines

Of course adding a fourth and fifth NIC multiplies the identification problem. Yes, some of my routers are supporting five network segments.

My question is, what's the algorithm for assigning Ethernet designations? I know it not placement order in the PCI bus, and I know its not the NIC data-link address.

So what is it?

Almost random. However, there's some evidence to suggest:
order of probing of device drivers
order of I/O addresses

Unfortunately, in systems with identical cards that are configured using plug-and-play methods such as those used by PCI random is the best shot you have...

Doei, Arthur.

Signature · 7 lines
  /\    / |      [email protected]      | Work like you don't need the money
 /__\  /  | A friend is someone with whom | Love like you have never been hurt
/    \/__ | you can dare to be yourself   | Dance like there's nobody watching

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to John Telford
Quoted 5 lines · Arthur van Leeuwen

Unfortunately, in systems with identical cards that are configured using plug-and-play methods such as those used by PCI random is the best shot you have...

'Deterministic' is more accurate. It seems to be random, on first boot. But it will almost never change after that unless you make hardware changes, in my experience.

Signature · 7 lines
Michael T. Babcock
CTO, FibreSpeed Ltd.


_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#3 lore raw
In reply to John Telford
Quoted 10 lines · Michael T. Babcock
Quoted 5 lines · Arthur van Leeuwen

Unfortunately, in systems with identical cards that are configured using plug-and-play methods such as those used by PCI random is the best shot you have...

'Deterministic' is more accurate. It seems to be random, on first boot. But it will almost never change after that unless you make hardware changes, in my experience.

Not in mine. Every time the PCI bus settings (can't recall the name right now, have been playing with a fixed hardware platform for quite a while) get reset there will probably be a different assignation. Yeah, it'll probably be deterministic *somehow*, but you'll be hard pressed to come up with any rules.

Doei, Arthur.

Signature · 7 lines
  /\    / |      [email protected]      | Work like you don't need the money
 /__\  /  | A friend is someone with whom | Love like you have never been hurt
/    \/__ | you can dare to be yourself   | Dance like there's nobody watching

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#4 lore raw
In reply to John Telford
Quoted 7 lines · John Telford

I'm building routers. It's difficult to tell in advance which NIC will be assigned eth0 and which will assigned eth1 when using two NICs. Ping testing usually clears up this simple problem.

The identification problem gets worse when adding a third NIC, after sorting out the first two NICs. Frequently the eth0 or eth1 assignments for the first two NICs change.

There are tricks to configure based on the MAC address of your interface instead of on its place in the probe. Perhaps googling on that will help.

Regards,

bert

Signature · 6 lines
http://www.PowerDNS.com          Versatile DNS Software & Services
http://www.tk                              the dot in .tk
http://lartc.org           Linux Advanced Routing & Traffic Control HOWTO
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#5 lore raw
In reply to John Telford

Thus spake bert hubert:

Quoted 11 lines · John Telford
Quoted 7 lines

I'm building routers. It's difficult to tell in advance which NIC will be assigned eth0 and which will assigned eth1 when using two NICs. Ping testing usually clears up this simple problem.

The identification problem gets worse when adding a third NIC, after sorting out the first two NICs. Frequently the eth0 or eth1 assignments for the first two NICs change.

There are tricks to configure based on the MAC address of your interface instead of on its place in the probe. Perhaps googling on that will help.

A script to rename interfaces with "ip link ... set name ..." after modprobe according to their hw addresses should suffice.

I never tried this because in my experience order of detection was always consistant between reboots assuming there are no hardware chasnges.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#6 lore raw
In reply to John Telford
Quoted 5 lines · Vladimir B. Savkin

A script to rename interfaces with "ip link ... set name ..." after modprobe according to their hw addresses should suffice.

I never tried this because in my experience order of detection was always consistant between reboots assuming there are no hardware chasnges.

If you turn on APIC you are in for a surprise I gather :-)

Regards,

bert

Signature · 6 lines
http://www.PowerDNS.com          Versatile DNS Software & Services
http://www.tk                              the dot in .tk
http://lartc.org           Linux Advanced Routing & Traffic Control HOWTO
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/