Skip to contentSkip to conversation

Priority queuing using tc not working

LARTC Neil Aggarwal 2 participants 3 messages Oct 18, 2002 – Oct 24, 2002

lore
Share & tools
lore
#0 lore raw

Hello:

I am trying to set up priority based queue for my VOIP traffic. I am running a RedHat 8.0 machine that is masquerading my internal network which has my PC and a VOIP phone. All VOIP traffic goes to and from my PBX, which is at 10.0.0.20.

When I use my phone and try to download a file via FTP on my PC, all of the packets are going into the low priority queue.

I typed these commands:
echo 1 > /proc/sys/net/ipv4/ip_forward

# Create the priority queue
/sbin/tc qdisc add dev eth0 root handle 1: prio /sbin/tc qdisc add dev eth0 parent 1:1 handle 10: sfq /sbin/tc qdisc add dev eth0 parent 1:2 handle 20: sfq /sbin/tc qdisc add dev eth0 parent 1:3 handle 30: sfq

# Add filters to put high priority packets into queue 1:1
/sbin/tc filter add dev eth0 pref 1 protocol ip parent 1:0 u32 match ip src 10.0.0.20 flowid 1:10 /sbin/tc filter add dev eth0 pref 1 protocol ip parent 1:0 u32 match ip dst 10.0.0.20 flowid 1:10

# Add a filter to put all remaining packets into queue 1:2
/sbin/tc filter add dev eth0 protocol ip parent 1:0 prio 2 u32 match ip dst 0.0.0.0/0 flowid 1:20

As you can see, from the output of '/sbin/tc -s qdisc ls dev eth0' there are no packets going into the high priority queue:

qdisc sfq 30: quantum 1514b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

qdisc sfq 20: quantum 1514b
Sent 432501 bytes 5118 pkts (dropped 0, overlimits 0)

qdisc sfq 10: quantum 1514b
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

qdisc prio 1: bands 3 priomap 1 2 2 2 1 2 0 0 1 1 1 1 1 1 1 1 Sent 432501 bytes 5118 pkts (dropped 0, overlimits 0)

Here is the output of /sbin/tc -s filter ls dev eth0:
filter parent 1: protocol ip pref 1 u32
filter parent 1: protocol ip pref 1 u32 fh 801: ht divisor 1
filter parent 1: protocol ip pref 1 u32 fh 801::800 order 2048 key ht 801 bkt 0 flowid 1:20
match 00000000/00000000 at 16
filter parent 1: protocol ip pref 1 u32 fh 800: ht divisor 1
filter parent 1: protocol ip pref 1 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:10
match 0a000014/ffffffff at 12
filter parent 1: protocol ip pref 1 u32 fh 800::801 order 2049 key ht 800 bkt 0 flowid 1:10
match 0a000014/ffffffff at 16
filter parent 1: protocol ip pref 2 u32
filter parent 1: protocol ip pref 2 u32 fh 801: ht divisor 1
filter parent 1: protocol ip pref 2 u32 fh 801::800 order 2048 key ht 801 bkt 0 flowid 1:20
match 00000000/00000000 at 16
filter parent 1: protocol ip pref 2 u32 fh 800: ht divisor 1
filter parent 1: protocol ip pref 2 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:10
match 0a000014/ffffffff at 12
filter parent 1: protocol ip pref 2 u32 fh 800::801 order 2049 key ht 800 bkt 0 flowid 1:10
match 0a000014/ffffffff at 16

Any ideas why the high priority traffic is not getting separated from the rest?

Thanks,
Neil

#1 lore raw

Joseph:

Based on you comments, I deleted all of the qdiscs and then typed these commands:
echo 1 > /proc/sys/net/ipv4/ip_forward

/sbin/tc qdisc add dev eth0 root handle 1: prio /sbin/tc qdisc add dev eth0 parent 1:1 handle 1:10 sfq

Immediately on typing this second command, I get this output:
Starting tc: RTNETLINK answers: File exists

Any ideas why I am getting this?

Thanks,
Neil.

--
Neil Aggarwal
JAMM Consulting, Inc. (972) 612-6056, http://www.JAMMConsulting.com
Custom Internet Development Websites, Ecommerce, Java, databases

Quoted 41 lines

-----Original Message-----
From: Joseph Watson [mailto:[email protected]]
Sent: Wednesday, October 23, 2002 8:22 PM
To: Neil Aggarwal
Subject: Re: [LARTC] Priority queuing using tc not working

Quoted 4 lines · Neil Aggarwal

Hello:

I am trying to set up priority based queue for my VOIP traffic. I am running a RedHat 8.0 machine that is masquerading my

internal network

Quoted 6 lines

which has my PC and a VOIP phone. All VOIP traffic goes to and from my PBX, which is at 10.0.0.20.

When I use my phone and try to download a file via FTP on my PC, all of the packets are going into the low priority queue.

Quoted 6 lines

I typed these commands:
echo 1 > /proc/sys/net/ipv4/ip_forward

# Create the priority queue
/sbin/tc qdisc add dev eth0 root handle 1: prio /sbin/tc qdisc add dev eth0 parent 1:1 handle 10: sfq

                                                                     ^^^
                                                                    1:10
Quoted 1 line

/sbin/tc qdisc add dev eth0 parent 1:2 handle 20: sfq

                                                                     ^^^
                                                                    1:20
Quoted 1 line

/sbin/tc qdisc add dev eth0 parent 1:3 handle 30: sfq

                                                                     ^^^
                                                                    1:30
Quoted 3 lines

# Add filters to put high priority packets into queue 1:1 /sbin/tc filter add dev eth0 pref 1 protocol ip parent 1:0

u32 match ip

Quoted 1 line

src 10.0.0.20 flowid 1:10 /sbin/tc filter add dev eth0 pref 1

protocol ip

Quoted 2 lines

parent 1:0 u32 match ip dst 10.0.0.20 flowid 1:10

Quoted 13 lines
Quoted 2 lines

# Add a filter to put all remaining packets into queue 1:2 /sbin/tc filter add dev eth0 protocol ip parent 1:0 prio 2

u32 match ip

Quoted 1 line

dst 0.0.0.0/0 flowid 1:20

^^^
Here is the problem, You dont have a 1:10
or 1:20 qdisc unless you make the
above corrections.

Signature · 3 lines
Regards

Joseph Watson

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Neil Aggarwal

I guess Probably this qdisc alread exist . Try to delete it and add it again and see what you are getting.
Nitin

Quoted 102 lines · --- Neil Aggarwal

Joseph:

Based on you comments, I deleted all of the qdiscs and
then typed these commands:
echo 1 > /proc/sys/net/ipv4/ip_forward

/sbin/tc qdisc add dev eth0 root handle 1:
prio
/sbin/tc qdisc add dev eth0 parent 1:1
handle 1:10 sfq

Immediately on typing this second command, I get
this output:
Starting tc: RTNETLINK answers: File exists

Any ideas why I am getting this?

Thanks,
Neil.

--
Neil Aggarwal
JAMM Consulting, Inc. (972) 612-6056,
http://www.JAMMConsulting.com
Custom Internet Development Websites, Ecommerce,
Java, databases

Quoted 5 lines

-----Original Message-----
From: Joseph Watson [mailto:[email protected]]
Sent: Wednesday, October 23, 2002 8:22 PM
To: Neil Aggarwal
Subject: Re: [LARTC] Priority queuing using tc not

working

Quoted 3 lines

On Friday 18 October 2002 07:43 pm, Neil Aggarwal

Quoted 3 lines · wrote:
Quoted 3 lines

Hello:

I am trying to set up priority based queue for

my VOIP traffic.

Quoted 1 line
Quoted 1 line

I am running a RedHat 8.0 machine that is

masquerading my

Quoted 2 lines

internal network

Quoted 1 line

which has my PC and a VOIP phone. All VOIP

traffic goes to and from

Quoted 3 lines
Quoted 3 lines

my PBX, which is at 10.0.0.20.

When I use my phone and try to download a file

via FTP on my PC,

Quoted 1 line
Quoted 1 line

all of the packets are going into the low

priority queue.

Quoted 6 lines
Quoted 6 lines

I typed these commands:
echo 1 > /proc/sys/net/ipv4/ip_forward

# Create the priority queue
/sbin/tc qdisc add dev eth0 root handle 1:

prio

Quoted 1 line
Quoted 1 line

/sbin/tc qdisc add dev eth0 parent 1:1 handle

10: sfq

Quoted 1 line
                  ^^^
Quoted 1 line
                 1:10
Quoted 1 line
Quoted 1 line

/sbin/tc qdisc add dev eth0 parent 1:2 handle

20: sfq

Quoted 1 line
                  ^^^
Quoted 1 line
                 1:20
Quoted 1 line
Quoted 1 line

/sbin/tc qdisc add dev eth0 parent 1:3 handle

30: sfq

Quoted 1 line
                  ^^^
Quoted 1 line
                 1:30
Quoted 2 lines
Quoted 2 lines

# Add filters to put high priority packets

into queue 1:1

Quoted 1 line
Quoted 1 line

/sbin/tc filter add dev eth0 pref 1 protocol

ip parent 1:0

Quoted 2 lines

u32 match ip

Quoted 1 line

src 10.0.0.20 flowid 1:10 /sbin/tc filter add

dev eth0 pref 1

Quoted 2 lines

protocol ip

Quoted 1 line

parent 1:0 u32 match ip dst 10.0.0.20 flowid

1:10

Quoted 2 lines
Quoted 2 lines

# Add a filter to put all remaining packets

into queue 1:2

Quoted 1 line
Quoted 1 line

/sbin/tc filter add dev eth0 protocol ip

parent 1:0 prio 2

Quoted 7 lines

u32 match ip

Quoted 1 line

dst 0.0.0.0/0 flowid 1:20

^^^
Here is the problem, You dont have a 1:10
or 1:20 qdisc unless you make the
above corrections.

Quoted 7 lines
Quoted 4 lines
Signature · 3 lines
Regards

Joseph Watson

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO:

http://lartc.org/

__________________________________________________
Do you Yahoo!?
Y! Web Hosting - Let the expert host your web site
http://webhosting.yahoo.com/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/