Skip to contentSkip to conversation

TEQL and balancing

LARTC Esteban Ribicic 2 participants 2 messages Nov 3, 2002

lore
Share & tools
lore
#0 lore raw

hi all.

this is my network

	  ----- eth1   
linux box |
	  ----- eth0

those nic connect me to my default router (172.0.0.1) and then to the internet. I always used one NIC but now, i need two. i thought using teql to merge those in one and then, route everything over thtat teql interface..i tryed this and did not work:

(after kernel 2.4 recompilation with QOS stuff)

# /etc/init.d/networking stop
Deconfiguring network interfaces: done.
# ifconfig
(shows nothing: OK)
# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use
Iface
(shows nothing: OK)
#
(set the interfaces i want to attach to teql0)
# tc qdisc add dev eth0 root teql0
# tc qdisc add dev eth1 root teql0
#
(set the ip address of those interfaces to my teql iface, those ips
where the one i used to have in my NIC)
# ip address add 172.0.0.81/24 dev teql0
# ip address add 172.0.0.82/24 dev teql0
#
# ip link set teql0 up
#
#
(set a default route to the device where my router is..used tyo be wth0,
now teql0)
# route add -net 172.0.0.0 netmask 255.255.255.0 dev teql0
(set a default route to my router)
# route add default gw 172.0.0.1
#
# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use
Iface
172.0.0.0       0.0.0.0         255.255.255.0   U     0      0        0
teql0
172.0.0.0       0.0.0.0         255.255.255.0   U     0      0        0
teql0
0.0.0.0         172.0.0.1       0.0.0.0         UG    0      0        0
teql0
(look that all goes to teql)
#
#
# ping 172.0.0.1
PING 172.0.0.1 (172.0.0.1): 56 data bytes

--- 172.0.0.1 ping statistics ---
4 packets transmitted, 0 packets received, 100% packet loss #
(nothing works)..

what could be wrong? im doing this because originaly, im planning to connect two cable modems in my house, and do some BW balancing...

is that posible?

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 64 lines · Esteban Ribicic

hi all.

this is my network

	  ----- eth1
linux box |
	  ----- eth0

those nic connect me to my default router (172.0.0.1) and then to the internet. I always used one NIC but now, i need two. i thought using teql to merge those in one and then, route everything over thtat teql interface..i tryed this and did not work:

(after kernel 2.4 recompilation with QOS stuff)

# /etc/init.d/networking stop
Deconfiguring network interfaces: done.
# ifconfig
(shows nothing: OK)
# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use
Iface
(shows nothing: OK)
#
(set the interfaces i want to attach to teql0)
# tc qdisc add dev eth0 root teql0
# tc qdisc add dev eth1 root teql0
#
(set the ip address of those interfaces to my teql iface, those ips
where the one i used to have in my NIC)
# ip address add 172.0.0.81/24 dev teql0
# ip address add 172.0.0.82/24 dev teql0
#
# ip link set teql0 up
#
#
(set a default route to the device where my router is..used tyo be wth0,
now teql0)
# route add -net 172.0.0.0 netmask 255.255.255.0 dev teql0
(set a default route to my router)
# route add default gw 172.0.0.1
#
# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use
Iface
172.0.0.0       0.0.0.0         255.255.255.0   U     0      0        0
teql0
172.0.0.0       0.0.0.0         255.255.255.0   U     0      0        0
teql0
0.0.0.0         172.0.0.1       0.0.0.0         UG    0      0        0
teql0
(look that all goes to teql)
#
#
# ping 172.0.0.1
PING 172.0.0.1 (172.0.0.1): 56 data bytes

--- 172.0.0.1 ping statistics ---
4 packets transmitted, 0 packets received, 100% packet loss #
(nothing works)..

Quoted 4 lines

what could be wrong? im doing this because originaly, im planning to connect two cable modems in my house, and do some BW balancing...

is that posible?

Yes, but teql is not made for this. Teql can be used to connect 2 linux boxes with 2 links.
There was a chapter in the lartc.org howto but I can't find it right now. You need some extra patches and you need to do natting on the linux box.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/