Skip to contentSkip to conversation

help needed using filters

LARTC Abraham van der Merwe 2 participants 4 messages Nov 16, 2002

lore
Share & tools
lore
#0 lore raw

Hi!

I'm trying to shape a traffic to/from a few different subnets using TBF. The way I understand it all I have to do is create a few queueing disciplines and attach a filter to each queueing discipline.

So for instance if I want to shape traffic going to 192.168.1.0/24 via eth0 to 64kbit then it should look like this:

------------< snip <------< snip <------< snip <------------ tc qdisc add dev eth0 root handle 1:0 tbf rate 64kbit burst 4kb latency 100ms peakrate 128kbit mtu 1500

tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip dst 192.168.1.0/24
------------< snip <------< snip <------< snip <------------

I can't add the filter above and I suspect it is due to

a) i can't add filters to tbf queueing disciplines? if so, why not?

b) i'm confused be the parent x:y and flowid a:b terminology in the filter. When do I use what?

Signature · 11 lines
Regards
 Abraham

Anyone can hold the helm when the sea is calm.
		-- Publius Syrus

___________________________________________________
 Abraham vd Merwe [ZR1BBQ] - Frogfoot Networks
 P.O. Box 3472, Matieland, Stellenbosch, 7602
 Cell: +27 82 565 4451 Http: http://www.frogfoot.net
 Email: [email protected]
#1 lore raw
Quoted 13 lines · Abraham van der Merwe

Hi!

I'm trying to shape a traffic to/from a few different subnets using TBF. The way I understand it all I have to do is create a few queueing disciplines and attach a filter to each queueing discipline.

So for instance if I want to shape traffic going to 192.168.1.0/24 via eth0 to 64kbit then it should look like this:

------------< snip <------< snip <------< snip <------------ tc qdisc add dev eth0 root handle 1:0 tbf rate 64kbit burst 4kb latency 100ms peakrate 128kbit mtu 1500

Quoted 7 lines

tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip dst 192.168.1.0/24
------------< snip <------< snip <------< snip <------------

I can't add the filter above and I suspect it is due to

a) i can't add filters to tbf queueing disciplines? if so, why not?

Because the tbf qdisc is classless. And filter are used to put packets in a child class. CBQ/HTB are examples of classfull qdiscs.
You add a tbf qdisc as the root qdisc. The root qdisc contains ALL packets that are sended. So you don't need filters.

Quoted 2 lines

b) i'm confused be the parent x:y and flowid a:b terminology in the filter. When do I use what?

Parent is the class where you add the filter. If you have class 10:1 and you want to add a filter to class 10:1, you have to use parent 10:1. When the filter matches a packet, it's placed in the class you specify with flowid. If you have class 10:1 with class 10:10 attached to it and you want to redirect packets to it, you have to specify "parent 10:1 flowid 10:10" in the filter command.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to Abraham van der Merwe

Hi Stef!

Quoted 15 lines
Quoted 15 lines

I'm trying to shape a traffic to/from a few different subnets using TBF. The way I understand it all I have to do is create a few queueing disciplines and attach a filter to each queueing discipline.

So for instance if I want to shape traffic going to 192.168.1.0/24 via eth0 to 64kbit then it should look like this:

------------< snip <------< snip <------< snip <------------ tc qdisc add dev eth0 root handle 1:0 tbf rate 64kbit burst 4kb latency 100ms peakrate 128kbit mtu 1500

tc filter add dev eth0 parent 1:0 protocol ip prio 1 u32 match ip dst 192.168.1.0/24
------------< snip <------< snip <------< snip <------------

Quoted 7 lines
Quoted 3 lines

I can't add the filter above and I suspect it is due to

a) i can't add filters to tbf queueing disciplines? if so, why not?

Because the tbf qdisc is classless. And filter are used to put packets in a child class. CBQ/HTB are examples of classfull qdiscs.
You add a tbf qdisc as the root qdisc. The root qdisc contains ALL packets that are sended. So you don't need filters.

Ok, so how do you do what I want to do in the example above using the TBF queuing discipline? All the examples I've seen so far uses CBQ, but that is not what I want since I don't want to specify the size of my interface/bandwidth (which is not needed to shape networks).

I obviously need a classful queuing displine so that I can make lots of sibling classes with filters attached to each one (with each filter's flowid pointing to a tbf qdisc in that class), but the question then is which queuing discipline should I use for this "container queueing discipline"?

Quoted 8 lines
Quoted 2 lines

b) i'm confused be the parent x:y and flowid a:b terminology in the filter. When do I use what?

Parent is the class where you add the filter. If you have class 10:1 and you want to add a filter to class 10:1, you have to use parent 10:1. When the filter matches a packet, it's placed in the class you specify with flowid. If you have class 10:1 with class 10:10 attached to it and you want to redirect packets to it, you have to specify "parent 10:1 flowid 10:10" in the filter command.

Thanks. This helps a lot.

Signature · 11 lines
Regards
 Abraham

QOTD:
	"My shampoo lasts longer than my relationships."

___________________________________________________
 Abraham vd Merwe [ZR1BBQ] - Frogfoot Networks
 P.O. Box 3472, Matieland, Stellenbosch, 7602
 Cell: +27 82 565 4451 Http: http://www.frogfoot.net
 Email: [email protected]
#3 lore raw
In reply to Abraham van der Merwe
Quoted 4 lines

Ok, so how do you do what I want to do in the example above using the TBF queuing discipline? All the examples I've seen so far uses CBQ, but that is not what I want since I don't want to specify the size of my interface/bandwidth (which is not needed to shape networks).

Cbq needs to know the NIC bandwidth for the internal calculations. If you have 10Mbit nic, you have to specify 10mbit. This is just for the calculations. Htb does not need this.

Quoted 5 lines

I obviously need a classful queuing displine so that I can make lots of sibling classes with filters attached to each one (with each filter's flowid pointing to a tbf qdisc in that class), but the question then is which queuing discipline should I use for this "container queueing discipline"?

You need to use htb or cbq for it. And you don't need the tbf to throttle the bandwidth. You can throttle the bandwidth of a class with htb or cbq itself. The classes are not reponsible for sending the packets, it's the qdisc attached to them that do this job. So all packets in the class, will get sended by the qdisc, so you don't need a filter to do this.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/