help with routing determined by source address
Hi!
I want to route packets where the gateway is determined by the source address and not the destination address - is this possible with iproute2?
for example:
ISP-A ISP-B
| | +---------------+ | linux machine + +---------------+
default gw is ISP-A interface, but if packet comes via ISP-B, the ISP-B interface should be used instead of ISP-A interface
Signature · 11 lines
Regards
Abraham
There ain't nothin' in this world that's worth being a snot over.
-- Larry Wall in <[email protected]>
___________________________________________________
Abraham vd Merwe [ZR1BBQ] - Frogfoot Networks
P.O. Box 3472, Matieland, Stellenbosch, 7602
Cell: +27 82 565 4451 Http: http://www.frogfoot.net
Email: [email protected]Quoted 2 lines · Abraham van der Merwe
Hi!
Hi,
Quoted 3 lines
I want to route packets where the gateway is determined by the source address and not the destination address - is this possible with iproute2?
Yes.
# When sraddr belongs to ISPA
ip rule add prio $PRIO_ISPA from $ISPA_NET lookup $ISPA_TABLE # When sraddr belongs to ISPB
ip rule add prio $PRIO_ISPB from $ISPB_NET lookup $ISPB_TABLE # Everything else
ip rule add prio $PRIO_DEFAULT lookup $DEFAULT_TABLE
Then;
# Default route through ISPA
ip route add table $ISPA_TABLE default via $ISPA_GW dev $ISPA_DEV # Default route through ISPB
ip route add table $ISPB_TABLE default via $ISPB_GW dev $ISPB_DEV
#For everything else, use a multipath route;
ip route add table $DEFAULT_TABLE nexthop via $ISPA_GW dev $ISPA_DEV nexthop via $ISPB_GW dev $ISPB_DEV
Quoted 10 lines
for example:
ISP-A ISP-B
| | +---------------+ | linux machine + +---------------+default gw is ISP-A interface, but if packet comes via ISP-B, the ISP-B interface should be used instead of ISP-A interface
IPs used on the linux machines, are private or public IPs ?
Cheers,
Vincent.
Signature · 6 lines
Vincent Jaussaud <[email protected]> Kelkoo.com - Security Manager _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Hi Vincent!
Quoted 11 lines
Quoted 3 lines
I want to route packets where the gateway is determined by the source address and not the destination address - is this possible with iproute2?
Yes.
# When sraddr belongs to ISPA
ip rule add prio $PRIO_ISPA from $ISPA_NET lookup $ISPA_TABLE # When sraddr belongs to ISPB
ip rule add prio $PRIO_ISPB from $ISPB_NET lookup $ISPB_TABLE # Everything else
ip rule add prio $PRIO_DEFAULT lookup $DEFAULT_TABLE
Quoted 8 lines
# Default route through ISPA
ip route add table $ISPA_TABLE default via $ISPA_GW dev $ISPA_DEV # Default route through ISPB
ip route add table $ISPB_TABLE default via $ISPB_GW dev $ISPB_DEV#For everything else, use a multipath route;
ip route add table $DEFAULT_TABLE nexthop via $ISPA_GW dev $ISPA_DEV nexthop via $ISPB_GW dev $ISPB_DEV
Thanks, this makes sense. I just don't understand the multipath route? Also, I take it the _TABLE variables can be arbitrary [unique] ids right? And if I want to have ISPB as the exception to the rule, I'll set ISPA's priority the highest?
Quoted 8 lines
Quoted 8 lines
for example:
ISP-A ISP-B
| | +---------------+ | linux machine + +---------------+
Quoted 4 lines
Quoted 2 lines
default gw is ISP-A interface, but if packet comes via ISP-B, the ISP-B interface should be used instead of ISP-A interface
IPs used on the linux machines, are private or public IPs ?
public ips
Signature · 10 lines
Regards Abraham BEWARE! People acting under the influence of human nature. ___________________________________________________ Abraham vd Merwe [ZR1BBQ] - Frogfoot Networks P.O. Box 3472, Matieland, Stellenbosch, 7602 Cell: +27 82 565 4451 Http: http://www.frogfoot.net Email: [email protected]
Quoted 6 lines · Abraham van der Merwe
Quoted 4 lines
#For everything else, use a multipath route;
ip route add table $DEFAULT_TABLE nexthop via $ISPA_GW dev $ISPA_DEV nexthop via $ISPB_GW dev $ISPB_DEVThanks, this makes sense. I just don't understand the multipath route?
I assume you want to be able to use both link simultaneously for the linux host itself (eg, for outgoing connections).
Setting a multipath route as shown below, will instruct the kernel to use the multipath route for all packets which don't have a saddr set. Eg, packets for which you don't care to use either ISP1 or ISP2.
Quoted 2 lines
Also,
I take it the_TABLEvariables can be arbitrary [unique] ids right?
Yes, any names you want, assuming they are present in /etc/iproute2/rt_tables. Otherwise, you can use numbers.
Quoted 4 lines
And if I
want to have ISPB as the exception to the rule, I'll set ISPA's priority the highest?
I'm not sure to understand what you mean.
Priorities means the order your routing tables will be looked at. eg;
ip rule add prio 100 lookup test
ip rule add prio 101 lookup test1
ip rule add prio 200 lookup test2
means that table test will be looked first, then table test1, then table test2.
Quoted 8 lines
Quoted 8 lines
Quoted 8 lines
for example:
ISP-A ISP-B
| | +---------------+ | linux machine + +---------------+
Quoted 6 lines
Quoted 4 lines
Quoted 2 lines
default gw is ISP-A interface, but if packet comes via ISP-B, the ISP-B interface should be used instead of ISP-A interface
IPs used on the linux machines, are private or public IPs ?
public ips
Sounds like you want to setup link redundency for your linux machine. This shouldn't be a problem for outgoing connections [except for FTP :)], but you may face some unexpected issues with incoming connections, for which the replies may not take the proper link; especially if the applications don't set the sraddr in the packet, in which case the multipath route will be used, which is bad.
Tell me how it goes, I'm working on a similar setup.
Cheers,
Vincent.
Signature · 6 lines
Vincent Jaussaud <[email protected]> Kelkoo.com _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/