CBQ or HTP accuracy
Hello,
I am rate limiting traffic going to some IP addresses using CBQ
(and want to change to HTB sometime).
While testing with different packet sizes I found out that I could go above the
rate limit I set. (even with HTB)
The values I use are: rate: 768kbit weight 77kbit allot 10000 avpkt 1512 I did not change the cell or other parameters.
My root qdisc is set to 40MBit.
With those values I am able to go up to 840kbit/s with packets sizes of 612 or 1224. With other values it's less except for very low values.
Changing the allot value (If I understood well allot*weight=max packets per round)
it only gets worst (tested with 1000 and 50000).
AVPKT is only used for maxidle so it should not change anything ?
What values should I tweak to have the max rate never exeeded and still be able
to come very near my max-rate using 1460 bytes packets ?
Would HTB be more accruate ?
Thanks for the HELP.
Signature · 9 lines
Thierry Coutelier /'\ ASCII Ribbon Campaign http://www.linux.lu \ / No HTML/RTF in email . × No Word docs in email . / \ Respect for open standards _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Quoted 25 lines · Thierry Coutelier
Hello,
I am rate limiting traffic going to some IP addresses using CBQ
(and want to change to HTB sometime).While testing with different packet sizes I found out that I could go above the
rate limit I set. (even with HTB)The values I use are: rate: 768kbit weight 77kbit allot 10000 avpkt 1512 I did not change the cell or other parameters.
My root qdisc is set to 40MBit.With those values I am able to go up to 840kbit/s with packets sizes of 612 or 1224.
With other values it's less except for very low values.Changing the allot value (If I understood well allot*weight=max packets per round)
it only gets worst (tested with 1000 and 50000).AVPKT is only used for maxidle so it should not change anything ?
Quoted 9 lines
What values should I tweak to have the max rate never exeeded and still be able
to come very near my max-rate using 1460 bytes packets ?Would HTB be more accruate ?
Thanks for the HELP.
Thierry,
to my knowledge, HTB is more predictable than CBQ and easier to set up.
If you want more accuracy, I suggest you modify a file in the kernel
source: include/net/pkt_sched.h
Change the #define for PSCHED_CLOCK_SOURCE from PSCHED_JIFFIES toPSCHED_CPU.
I've read this suggestion on the list but never tried it yet. Note
that this is valid only for CPUs that support a TSC (Pentium and up).
Regards,
Stephane
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
I already tried it and it does not improve much the behaviour.
With which parameters should I play in HTB and CBQ ?
Quoted 53 lines · Stephane Ouellette
Quoted 25 lines · Thierry Coutelier
Hello,
I am rate limiting traffic going to some IP addresses using CBQ
(and want to change to HTB sometime).While testing with different packet sizes I found out that I could go above the
rate limit I set. (even with HTB)The values I use are: rate: 768kbit weight 77kbit allot 10000 avpkt 1512 I did not change the cell or other parameters.
My root qdisc is set to 40MBit.With those values I am able to go up to 840kbit/s with packets sizes of 612 or 1224.
With other values it's less except for very low values.Changing the allot value (If I understood well allot*weight=max packets per round)
it only gets worst (tested with 1000 and 50000).AVPKT is only used for maxidle so it should not change anything ?
Quoted 9 lines
What values should I tweak to have the max rate never exeeded and still be able
to come very near my max-rate using 1460 bytes packets ?Would HTB be more accruate ?
Thanks for the HELP.
Thierry,
to my knowledge, HTB is more predictable than CBQ and easier to set up.
If you want more accuracy, I suggest you modify a file in the kernel
source:include/net/pkt_sched.hChange the #define for
PSCHED_CLOCK_SOURCEfromPSCHED_JIFFIEStoPSCHED_CPU.I've read this suggestion on the list but never tried it yet. Note
that this is valid only for CPUs that support a TSC (Pentium and up).Regards,
Stephane
Signature · 9 lines
Thierry Coutelier /'\ ASCII Ribbon Campaign http://www.linux.lu \ / No HTML/RTF in email . × No Word docs in email . / \ Respect for open standards _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/