Skip to contentSkip to conversation

questions with Stef's scripts

LARTC James Ma 2 participants 2 messages Dec 5, 2002 – Dec 6, 2002

lore
Share & tools
lore

James Ma

author
#0 lore raw

Hi, Stef,

I have some questions with your following scripts on www.docum.org,

BW1=$1'kbps'
BW2=expr 100 - $1
BW2=$BW2'kbps'

tc qdisc del dev eth0 root handle 1:

tc qdisc add dev eth0 root handle 1: htb default 12
tc class add dev eth0 parent 1: classid 1:1 htb rate 100kbps ceil 100kbps burst 2k tc class add dev eth0 parent 1:1 classid 1:10 htb rate $BW1 ceil 100kbps burst 2k tc class add dev eth0 parent 1:1 classid 1:11 htb rate $BW2 ceil 100kbps burst 2k

tc filter add dev eth0 parent 1: protocol ip prio 3 handle 1 fw classid 10:10 tc filter add dev eth0 parent 1: protocol ip prio 3 handle 2 fw classid 10:11

iptables -F
iptables -X
iptables -N acc_0
iptables -N acc_1
iptables -A OUTPUT -t mangle -p tcp --dport 2000 -j MARK --set-mark 1 iptables -A OUTPUT -t mangle -p tcp --dport 2001 -j MARK --set-mark 2 iptables -A OUTPUT -p tcp --dport 2000 -j acc_0
iptables -A OUTPUT -p tcp --dport 2001 -j acc_1

My questions are as follow,
1.Why the classid in tc filter are "10:10 and 10:11" instead of "1:10 and 1:11"? How can you associate the filters with the classes you defined before?
2.What does "fw" before "classid" in tc filter mean? Does it refer to forward chain? 3.I guess the "handle 1" in tc filter refer to "mark1" in iptables, am I right? But is there any sequence problem to define handle 1 first and mark1 later in the scripts? 4.Where can I find procedure on how to install HTB and compile kernel to use it?

Your answer will be much appreciated,

Regards,

James

#1 lore raw
Quoted 29 lines · James Ma

Hi, Stef,

I have some questions with your following scripts on www.docum.org,

BW1=$1'kbps'
BW2=expr 100 - $1
BW2=$BW2'kbps'

tc qdisc del dev eth0 root handle 1:

tc qdisc add dev eth0 root handle 1: htb default 12
tc class add dev eth0 parent 1: classid 1:1 htb rate 100kbps ceil 100kbps burst 2k tc class add dev eth0 parent 1:1 classid 1:10 htb rate $BW1 ceil 100kbps burst 2k tc class add dev eth0 parent 1:1 classid 1:11 htb rate $BW2 ceil 100kbps burst 2k

tc filter add dev eth0 parent 1: protocol ip prio 3 handle 1 fw classid 10:10 tc filter add dev eth0 parent 1: protocol ip prio 3 handle 2 fw classid 10:11

iptables -F
iptables -X
iptables -N acc_0
iptables -N acc_1
iptables -A OUTPUT -t mangle -p tcp --dport 2000 -j MARK --set-mark 1 iptables -A OUTPUT -t mangle -p tcp --dport 2001 -j MARK --set-mark 2 iptables -A OUTPUT -p tcp --dport 2000 -j acc_0
iptables -A OUTPUT -p tcp --dport 2001 -j acc_1

Quoted 4 lines

My questions are as follow,
1.Why the classid in tc filter are "10:10 and 10:11" instead of "1:10 and 1:11"? How can you associate the filters with the classes you defined before?

Because I did a wrong copy 'n paste :)
Where have you found that scripts so I can corrrect it ?

Quoted 2 lines

2.What does "fw" before "classid" in tc filter mean? Does it refer to forward chain?

No to firewall. Fw is a filter that uses the marks you placed on packets with firewall commands like iptables or ipchains.

Quoted 3 lines

3.I guess the "handle 1" in tc filter refer to "mark1" in iptables, am I right? But is there any sequence problem to define handle 1 first and mark1 later in the scripts?

No, the filtering is done when the packet is sended out on the wire, so long after the iptables rules are processed.

Quoted 2 lines

4.Where can I find procedure on how
to install HTB and compile kernel to use it?

Kernel 2.4.20 has htb support. You only need to patch iproute2 for htb support. Or go to www.docum.org, I placed a tc binary online on the faq page.

Stef

Signature · 8 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.oftc.net

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/